Got a little problem, maybe big =(
Basically the phone one day decided not to work
i can get only two screens
either the start-up splash screen displaying CINGLAR and the firmware stuff on the bottom corner
or
if i enter bootloader mode, i get SERIAL 2.07 and nothing else
i have tried hard reset, take out the battery for ever, even flash
hard reset does nothing, soft does nothing
take out the battery does nothing
the phone won't charge through the cradle or charger, i can only charge the battery alone using the cradle
as for flashing it won't flash in the cingular splash screen or the bootloader screen, it doesn't change from SERIAL to USB when connected, thus the computer can't send anything to it
what can i do ?????
Do you have an SDIO card in the top slot? That can cause problems with the bootloader accepting the image from the PC.
nope only have the original DEMO SD plastic
any one what could be wrong ?
had same problem
dont know if you are doing the wm5.0 hard reset or teh old style hard reset that we used to on wm2003se. its teh notes button, camera, power and soft reset button. clear registry and the storage and then it should work. it did for me.
tried your reset steps boots the bootloader =(
Re: BA - SX66 Variant won't load - stuck in Splash or Bootlo
evilgabbie said:
if i enter bootloader mode, i get SERIAL 2.07 and nothing else
...
what can i do ?????
Click to expand...
Click to collapse
BigDamHero said:
If you got bootloader mode then you should be able to upgrade your rom to whatever you like.
Step by step insturctions are on WIKKI. The page for upgrading to the most recent ROM for the Blue Angel that IS NOT WM2005 is here:
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
If your device is in bootloader mode just put it in the cradle (activsync won't start but don't worry about that) and start the upgrade!
Click to expand...
Click to collapse
When you get to the Bootloader screen, probably you are home free. Just use the abouve link to resolve you problem.
BootLoader Loop Issue - SX66 Siemens
I am having a similar issue , where i am unable to hard reset or soft reset ,If I place SX66 (SIEMENS) in cradle it appears to charge after charge is complete , it will go to bootloader menu.
==========================================================
I have downloaded the MTTY , and would to know the settings required for USB , is selected from dropdown what is the optimal choice to make.
Im not seeing the cmd line " CMD> " in using MTTY.
I was gonna use com ports but dont know the settings to set:
==========================================================
parity
data bits
stop bits
flow control
local echo
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
had exactly the same problem, follow these steps for hard reset
my phone came good after (running wm6)
Hi, All
I just tried the WM6 for x51v last night, but my x51 can not boot up any more. The SD image loader processed the image loading without any error and when it asked hard reset, I did right as it said. But after I saw the hard reset screen, which showed "press contact key to restore, press message key to cancel". I tried both keys in diferent hard reset, no one works. The screen got dark again without anything displayed. I waited over 5 minutes to see anything happen. But nothing.
Now the x51 only can show hard reset screen, can not power on. And can not run SD image loader again. Anyone here has any idea about how to solve the problem? Thanks in advance.
Tried to upload the software on my MDA Pro and all of a sudden the screen on the MDA goes blank. I've tried master reset and i press 0 and it says clearing or whatever. Then it goes to the USB/Serial Screen and it reads v1.01 at the bottom. What do I do?
Hi, could you please post some more details? e.g. Which version was originally on the Universal and which version did you flash....
Cheers
Michael
Hi,
You just need to run the Upgrade again. As long as it says USB when you have it connected, no harm is done.
Cheers,
vma
No...There is definately some damage done. Its stuck on the boot load screen Where it says Serial at the top and V1.01 on the bottom. I just got it new in the box untouched and totally screwed it up trying to update the software to "UNI_TMUK_130114_130232_11003_WWE_BL101_Ship" I dont know what the original rom software was at all. It went to the grey screen that it is stuck on now and the power nor reset button works. The letters are still there in black on a grey non lit screen. Master reset (soft keys+rest) brings me to the screen but after i press 0 it says clearing now but goes right back to the serial/v# screen(boot load mode)....thats it...
Look it's not damaged. It boots to the bootloader. So long as it has the bootloader it's COMPLETELY recoverable.
1st thing you need to do is look here.
Scroll to the bottom and use method 2... It's a LOT easier and has saved my bacon many times!.
Psi
Hi all,
Just received my Vodafone-branded Diamond, and I'm afraid I already managed to brick it!
It was equipped with version "1.37.172.3 NLD" so I decided to upgrade it to the latest version.
The installation of OliNex Hard-SPL 1.93 went flawless, but the installation of ROM "RUU_Diamond_HTC_WWE-ME_1.93.456.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe" stopped at about 25% with error code 302. The recovery method that came with the package didn't help, every time the upgrade stopped at the same moment.
Since the device is stuck in the bootloader, and I'm left with a non-chargeable battery, I tried the official Vodafone-branded "RUU_Diamond_Vodafone_NL_1.97.172.4_Radio_Signed_Diamond_52.44.25.24_1.08.25.08_Ship.exe" ROM. Unfortunately, this upgrade stops at 48% and throws the same 302 error.
Anyone who can tell me what I'm doing wrong, and what I can do to solve all this?
I hope I don't have a brand new, but bricked device on Christmas!
TIA and have a nice day.
Try a hard reset first. If this doesn't help google or search at XDA for MTTY.
This tool can fix your device
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
Try this, maybe will work
Try a Vodafone branded stock rom before mtty.
Regards,
Carty..
He already tried a stock rom....
Potential Solution
Have you looked at the thread titled,
[UPG][TRBL]How-to fix: Update/Flash doesnt work, stops at 0% or 5% (invalid model ID)
It may just be a model ID glitch that can me fixed.
Take a look. It's in this forum in a sticky by cptsunshine.
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Besides, the bootloaders says upgrade ROM code error please try again.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Install Rom via Internal Memory Method
Steps from Suiller:
1. open from your PC the rar or zip archive and extract only the BIG .nbh file
2. rename as DIAMIMG.NBH
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!)
4. reset your device and within 3 seconds push together the Vol_Down + Back button (the one on the right above the hangup button) and keep pressed until the boot loader appears (the one with the color stripes)
5. soon as you see the bootloader stop to press those poor buttons
6. a very simple gray menu will appear asking you what to do, simple press the power button to perform the ROM/Radio upgrade
7. while the upgrade runs be patient and don't press again the power button, reset the device or play with it until it finishes, when finished a message "UPDATE SUCCESS" will appear, now you can safely reset your device
8. who prefer can perform a hard reset after the fresh cook (soon after reset simply press Vol_Down + Circle button, then when you see another simple gray menu choose Vol_Up to confirm format), even if this has no-sense because internal memory is pre-formatted during flash, but... there is always a but... for some unknown "scientific" reason sometimes an hard-reset can save time & headache
Let me know how it goes.
Make sure you have Net framework 3.5 installed on devices.
Nakkie27 said:
Thanks all for the help, I'll have a look at your suggestions.
The problem isn't that it stops at 0% or 5%, it stops at random percentages (depending on the ROM I use).
I also see the bootloader (red / green / blue), so it's not dead. I guess it's just that it doesn't pick up a ROM.
Edit:
A hard reset doesn't seem to work. In the bootloader, when I press "volume down" and "enter" together, and press the "reset button" the screen goes black, but then goes back to the bootloader screen after a sec or 2.
Edit 2:
MTTY doesn't do much either, after executing "boot" the phone is showing me the Vodafone logo and that's it.
For the rest, MTTY shows me the following:
Cmd>boot
InitDisplay: Display_Chip=1
dwDirectNum: 0, dwMatrixNum: 0, dwMicroPNum: 0
Fixed new dwPSImageSize = 0x53E0000
Click to expand...
Click to collapse
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
band27 said:
Steps from Suiller:
3. copy the renamed file into the root dir of your "Storage Card" or "Internal Storage" (the one of 4Gb... NOT to the internal phone memory!
Click to expand...
Click to collapse
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
janielsen said:
u can do one thing then press woluem down and reset bottom at the same time then u go to rescue mode then u wait and put in the usb stick and there stand seriel when u put in the cable it will change to usb thenu can load the firmware again
Click to expand...
Click to collapse
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Nakkie27 said:
I wish I could mate, but I cannot put files on it anymore, since ActiveSync doesn't recognize my device when it's in the bootloader.
Can you please be more specific? Are you telling me how to do a hard reset? I tried as to do a hard reset, but it goes back to the bootloader instead of resetting. USB stick?
Thanks all, much appreciated. A pain this can happen, looking at the fact that I did everything exactly as described in all these flashing manuals.
Click to expand...
Click to collapse
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
janielsen said:
first push the volum down buttom at the same time press the reset buttom then the 3 color display will appear and in the buttom will stand seriel then u putt in the usb cable to ur phone whit u have attact to ur pc then it will say usb now u can load new firmware
Click to expand...
Click to collapse
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on, and I can't get a USB-connection.
Edit:
Volume down + reset brought me in the bootloader again, although it's saying SPL-1.93.OliNex.
Nakkie27 said:
No mate, I never had problems getting into the 3 color screen. The problem was updating afterwards, which never completed without error code 302.
Anyway, I guess I just fully bricked my device after putting SPL-1.40.OliNex (according to the guide at http://forum.xda-developers.com/showthread.php?t=416211) on it. The SPL install was succesful, but when booting I'm now not even getting to see the 3 color bootloader. All I see is the Vodafone logo with some version numbers at the bottom, but that's it. It doesn't boot further on.
Click to expand...
Click to collapse
that i know but as i say in the post that when u do it that way i say u can load new firmware whitout it needs to boot try my friend i have done it 3 times because wrong loading of firmware
u have to only push thoose 2 buttom then it will work because u go to rescue mode
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Nakkie27 said:
But what will that give me extra? I can access the Hard-SPL 1.93 bootloader (3 color screen), and I can get into USB mode. It's just that the upgrade of both firmwares stop at a certain percentage.
I'm constantly trying to hard reset the device, but after pushing the reset button (with both volumn down + enter pressed down), the device just reboots back into the bootloader and doesn't give me the hard reset warning.
Click to expand...
Click to collapse
u need to hold them down until it leave the 3 color display an turns into grey
Ok, finally managed to do a hard reset. Afterwards I tried upgrading to the official Vodafone NL 1.97 ROM once more, but it failed at 48% again.
Any ideas what to do? I know have Diamond with Hard-SPL 1.93 (which says upgrade ROM code error) with no working OS.
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Hi all,
I have a quit similar problem. I've read a lot, but couldn't find an answer to my problem - may bye someone can help me.
I updated my Dimond (OliNex Hard-SPL 1.93, radio 1.09.25.23 and rom dutty V4). When I start my phone most of the time (95% plus) I end up in the color screen - however some time it's starts perfect (without changing anything).
When I get stock in the color screen, I can start the phone with mtty and the command "boot".
What can I do to make my phone always start in the normal way?
Thanks!
Nakkie27 said:
Ok all, got it finally working again!
Don't ask me why, but flashing the newest Dutty ROM (and the included radio) did work.
Thanks for all your help, and a wonderful evening!
Click to expand...
Click to collapse
i smell a radio issue - last time i was trying to upgrade my radio - ended up with something similar, managed it out like you did - but now you're up - so that's good!!
try some other rom (this time without radio) - i don't think you should have any issues going forward... good luck and have fun!
Hi, yesterday, suddenly, my Artemis no longer starts.
On the screen appears only the bootscreen with IPL;SPL and GSM code...no Os and then the screen sweetly disappears!
J tried to soft and hard reset more and more times ....but nothing.....!!!!
Is there something i can try to do before throwing in the trash my Artemis......
Thanks
that happened to me before try entering bootloader and flashing from there
to enter bootloader you hold the to top buttons, power and voice commander and insert the stylus enter the soft reset hole
Solved
Thanks
pablo34 said:
that happened to me before try entering bootloader and flashing from there
to enter bootloader you hold the to top buttons, power and voice commander and insert the stylus enter the soft reset hole
Click to expand...
Click to collapse
no problem just helping out