Hi all! I hope I'm not disturbing here, but I'm quite desperate with regards to my poor BA... After replacing the display about a year ago (the touch-sensitive layer had broken) everything was going well, but something bad has been happening for some months now, and I think it has come to the point of no-return...
At first, when I slid the BA open, there would be a point in which a change in the colors on the display happened, as if the the Red and Blue channels worked well while the Green one was dim (as noticeable during the boot process). Then, opening it completely, it came back to the normal state. The situation worsened, sort of "interference" could be seen while opening the BA, the touchscreen would lose calibration after some openings and closings and so on...
Now the worst: when I turn it on, the screen is completely blank and white; sliding it back and forth would once get it to work, but now it is completely useless. About halfway between the open and closed positions the backlight itself turns off and then on again. It is impossible to see anything and it is unusable!! I opened the BA and made sure everything was connected, I re-connected the LCD and the touchscreen cable but nothing changed... I don't know what to do...
Does anyone have any suggestions? Can I try to repair it or to have it repaired, or, as it is a bit visibly used, should I resign myself to saying it goodbye?? Thanks for your patience and help...
News!! I rried to replace the new screen with the old (broken touchscreen) one, and that one works. Save for a problem, the green colour is lightly dim in the exact positions in which the backlight goes off with the "new" but not working display... Does anyone have an explanation for this behaviour? Thanx again!!
I have put in a new LCD screen into the device and it refuses to power up.
I can still hear wm6 in the background loading with all my reminders etc.
The old screen is cracked but still powers up etc.
Any ideas?
Fixed the problem.
I had to make sure all the contacts were touching for the LCD screen to work properly.
I guess during the cracking it bent something....
Hi! I have a big problem with my Rhodium.
I have post another similar thread before but aybody seems to respoding..
I don't know what happened to my phone.
The touchflo3D seems to not responding. in other words the screen reacts when I tap on it, but I can't move or select anything on the screen.
I don't understand if it's a software or hardware problem.
The problem born with a custom rom I installed.
R [WWE|GER|FRA|ITA|NLD] |Feb 12| Energy™-.¸¸.·´¯ 6.5|21916 / 6.5.X|28244 * Sense 2021
after few days of no problem, the screen became as I described, incapable to select anything.
I tried also to move to the settings to disactivate sense but it was impossible with only the keyboard.
I searched on the forum for the solution, but the methods proposed didn't resolve the problem!
So I decided to return to the ufficial Rom.
RUU_Rhodium_HTC_ITA_1.19.408.1_Radio_Rhodium_3.44. 25.27_Signed_Ship
I performed a HardReset before the reinstall of the ufficial rom, but the problem remained.
So I performed a task29, but after the reinstall nothing changed and the TouchFlo seem to be broken.
I followed the guides proposed but I don't think I commited something wrong...
I suppose is a problem of the software because, I repeat, the screen react to my tap when is in minimum light.
Please help me because I don't know whato to do...
Tnx to All!!!!
Is the issue *only* with Touchflo? Can you tap on the Start menu and bring it up?
I'm confused as to why you say "the screen reacts when I tap on it, but I can't move or select anything on the screen"
How can you tell if the screen reacts?
Mnementh666 said:
Is the issue *only* with Touchflo? Can you tap on the Start menu and bring it up?
I'm confused as to why you say "the screen reacts when I tap on it, but I can't move or select anything on the screen"
How can you tell if the screen reacts?
Click to expand...
Click to collapse
Hi! No I can't tap on the start menù and when I tap on any icon on the screen nothing happens!
What I meant with "the screen seems to react" is that (sorry for my English XD!) before the screen goes black, the light goes high to low, ok?
when the screen has low light, and I tap on the screen, the light goes to high, so it seems that the screen can react to my tap.
tnk you very much for your response.
If I wasn't capable to explain correctly, please tell me 'cause I'm a little worried for my phone!
Bye.
i don't want to bring down any hope left, but if it does not respond to anything you do, i think your phone has just lost its flat cable. It might be broken and fixing it up would be a total pain. I would bring it back to where you bought it. Contact me through pm for further details, if u're still wondering what does this mean.
G4rreT84 said:
Hi! No I can't tap on the start menù and when I tap on any icon on the screen nothing happens!
What I meant with "the screen seems to react" is that (sorry for my English XD!) before the screen goes black, the light goes high to low, ok?
when the screen has low light, and I tap on the screen, the light goes to high, so it seems that the screen can react to my tap.
tnk you very much for your response.
If I wasn't capable to explain correctly, please tell me 'cause I'm a little worried for my phone!
Bye.
Click to expand...
Click to collapse
This sounds either like a broken / damaged ribbon cable (the "flat cable" the previous poster was referring to) or a damaged / broken digitizer.
On my old phone, the digitizer slowly broke - first the accuracy of the touchscreen would slide, then it got to the point where it wouldn't register 'on screen' at all, even though the phone could still tell I was tapping the screen because the backlight would come on etc, just as you describe.
Replacing the digitizer will cost money, but if you're going to do that find someone good at doing it! And also consider getting the device checked out and replacing the ribbon cable too, it's probably one of the most vulnerable parts of the device so it can never hurt to be overly cautious and replace both of them. Unfortunately there's always a cost involved
Let us know how you get on...
Hi the cable is not the only thing that can couse your screen to not respond, ive seen a tp2 that stoped responding because IT captured humidity in the digitizer screen, you can tell if this is the case by mooving your phone under the sun light and you will notice a kind of rainbow loking transparente spot, this humidity causes the digitizer screen to get stuck, the Solution can be to let it dry in the sun, or to rub it jently against your leg, the fricción can help to dry out the humidity, hope IT helps.
Search on here "tp2 screen not responding"
There is a thread on here I found about the screen not responding, and cleaning around the chrome edge with something thin, carefully, (I used my fingernail, which worked, but I lifted the contact too much down by the buttons on the bottom of screen). Worked for me and a few others. Good luck.
Hello
i have an issue that makes my screen is not rotating when i slide down the screen.
It seems that the hardware screen closed detection is not responding.
my problem is that i have totaly disassembly my tp2 in order to change some parts.
After cleening all the electronics part i h'ave re-assembly every things. Now it's working fine exepted this issue.
The screen is keeping the landscape mode without possibility to change it.
Do you have any idea ?
Does any body know how the screen closed sensor works ? An where it is ?
any picture ?
my problem is exactly the same as
http://forum.xda-developers.com/showthread.php?t=1282596
It's a magnetic sensor, but I don't know much more about it.
iFixIt might help you.
Hi.
My LG G3 D850 have some hardware issue.It is working i can receive calls but showes blank screen .when i tap on screen it lights up but blank.
I have replaced screen but it seems its problem in the board,not in screen .
I am also 100 percent sure its not software issue .
Kindly if someone had this kind of problem then guide me which component of the board is causing this problem.
Hi,
Attached picture shows a blue screen not a blank screen : symptom of a dead motherboard (defective GPU connection : no repair)
Sorry