(SOLVED) [HELP] Almost dead Wildfire S! - HTC Wildfire S

Hello Everybody
Well, a few days ago while i was calling somebody, my Wildfire S "a510b" had turned itself off and when i tried to turn it back on it vibrate once then never did that again.
i've tried to connect it to charger, all what i got is a blinking orange led... seems to be not charging for the low voltage of the battery.
I've tried to connect it to PC, same Blinking led and nothing on PC at all... even no notification that a dvice is connected!
I've tried to start it in different modes, and this is what i got:
Power button = nothing
Vol up + Power = nothing
Vol down + Power = nothing
Vol up + Vol down + Power = 5 vibrates and solid orange led, here i tried to connect it to PC and it recognized it as "qualcomm cdma technologies msm " no drivers found so i download them manually...
i've tried this post:
http://forum.xda-developers.com/showpost.php?p=14831391&postcount=9
did not work...
please, what is my situation and what can i do?
I'm looking into this forum for 3 days and nothing seemed to work!
thanks in advanced
Edit: it's a problem with the hard disk. Repairing it coasts a lot so I'll keep my phone as a good memory.
Thanks for all the helping tries.

FerasAlfrih777 said:
Hello Everybody
Well, a few days ago while i was calling somebody, my Wildfire S "a510b" had turned itself off and when i tried to turn it back on it vibrate once then never did that again.
i've tried to connect it to charger, all what i got is a blinking orange led... seems to be not charging for the low voltage of the battery.
I've tried to connect it to PC, same Blinking led and nothing on PC at all... even no notification that a dvice is connected!
I've tried to start it in different modes, and this is what i got:
Power button = nothing
Vol up + Power = nothing
Vol down + Power = nothing
Vol up + Vol down + Power = 5 vibrates and solid orange led, here i tried to connect it to PC and it recognized it as "qualcomm cdma technologies msm " no drivers found so i download them manually...
i've tried this post:
http://forum.xda-developers.com/showpost.php?p=14831391&postcount=9
did not work...
please, what is my situation and what can i do?
I'm looking into this forum for 3 days and nothing seemed to work!
thanks in advanced
Click to expand...
Click to collapse
The thread you mentioned is the solution, but you might have to use a PG76IMG.zip suited for you model, you can try using an RUU and take the file from that. Where did you buy the device from? That will help narrow down the file you have to use.

csoulr666 said:
The thread you mentioned is the solution, but you might have to use a PG76IMG.zip suited for you model, you can try using an RUU and take the file from that. Where did you buy the device from? That will help narrow down the file you have to use.
Click to expand...
Click to collapse
thank you for replying, but i've tried this... and renamed the rom PG76IMG.zip,
the problem is Vol down + Power does nothing!
i've tried it using Vol down Vol up and Power... but nothing happened
Does the keys i pressed in my model replaces the keys they mentioned in PG31?
thanks again

FerasAlfrih777 said:
thank you for replying, but i've tried this... and renamed the rom PG76IMG.zip,
the problem is Vol down + Power does nothing!
i've tried it using Vol down Vol up and Power... but nothing happened
Does the keys i pressed in my model replaces the keys they mentioned in PG31?
thanks again
Click to expand...
Click to collapse
What rom did you use?

well
csoulr666 said:
What rom did you use?
Click to expand...
Click to collapse
i use RUU_Marvel_HTC_ARA_1.47.415.1_R3_Radio_47.10b.35.3030H_7.47.36.10M_release_196164_signed.exe
i've downloaded it from: shipped-roms (sorry i can't post links yet)
after opening the exe file i went to %temp% and searched for ROM.zip and renamed it as PG76IMG.zip and followed the post steps

FerasAlfrih777 said:
i use RUU_Marvel_HTC_ARA_1.47.415.1_R3_Radio_47.10b.35.3030H_7.47.36.10M_release_196164_signed.exe
i've downloaded it from: shipped-roms (sorry i can't post links yet)
after opening the exe file i went to %temp% and searched for ROM.zip and renamed it as PG76IMG.zip and followed the post steps
Click to expand...
Click to collapse
Elaborate a bit on what happened when following the steps, that might help in pointing out any errors

csoulr666 said:
Elaborate a bit on what happened when following the steps, that might help in pointing out any errors
Click to expand...
Click to collapse
well, after renaming the ROM.zip i formatted the SD card format Fat32 and copied the rom there then pushed the buttons up + down + power and i had 5 vibrates and a solid orange led and waited 4 mins then pressed up to confirm the update then waited another 5 mins then pressed up again... at this point -as they said- i should have a single vibrate but i had nothing at all.
i have charged the battery to full on a wall charger... also during the proccess the screen is black...

FerasAlfrih777 said:
well, after renaming the ROM.zip i formatted the SD card format Fat32 and copied the rom there then pushed the buttons up + down + power and i had 5 vibrates and a solid orange led and waited 4 mins then pressed up to confirm the update then waited another 5 mins then pressed up again... at this point -as they said- i should have a single vibrate but i had nothing at all.
i have charged the battery to full on a wall charger... also during the proccess the screen is black...
Click to expand...
Click to collapse
is your bootloader unlocked? Unlocked bootloaders are unable to install stock roms by this method

csoulr666 said:
is your bootloader unlocked? Unlocked bootloaders are unable to install stock roms by this method
Click to expand...
Click to collapse
no sir, it's not

still unsolved
could Riff box help in my case?

FerasAlfrih777 said:
could Riff box help in my case?
Click to expand...
Click to collapse
It will if you know how to use it.

Related

flashed wrong kernel

guys unfortunately i just flashed xperia Z kernel using fasboot in my beloved xperia zl..now it is not booting up,only red light glowing...i think it is dead please help..
vivekrules said:
guys unfortunately i just flashed xperia Z kernel using fasboot in my beloved xperia zl..now it is not booting up,only red light glowing...i think it is dead please help..
Click to expand...
Click to collapse
Calm dowm man, i already did that **** once kkkkkk
Simple: Hold down the reset buton till your cellphone vibrate 3 times (That hide one beside your SD Card). That'll turn it off. So hold down your Volume ( - ) button and plug your USB, now you are in flash mode.
Open Flash Tools and flash a Stock ROM (Recommended) or Stock Kernel, That's it!
viniciusnc said:
Calm dowm man, i already did that **** once kkkkkk
Simple: Hold down the reset buton till your cellphone vibrate 3 times (That hide one beside your SD Card). That'll turn it off. So hold down your Volume ( - ) button and plug your USB, now you are in flash mode.
Open Flash Tools and flash a Stock ROM (Recommended) or Stock Kernel, That's it!
Click to expand...
Click to collapse
thanks for your reply buddy..but nothing is happening when i press that yellow reset button beside my sd card
vivekrules said:
thanks for your reply buddy..but nothing is happening when i press that yellow reset button beside my sd card
Click to expand...
Click to collapse
You need to hold it down till it vibrate three times.
No fear, only hold it down
viniciusnc said:
You need to hold it down till it vibrate three times.
No fear, only hold it down
Click to expand...
Click to collapse
Thanks a ton buddy..u saved my A**:good:
vivekrules said:
Thanks a ton buddy..u saved my A**:good:
Click to expand...
Click to collapse
Sorry for bumping this thread, but I got exactly the same problem described by OP. But I simply can't get into the flashmode.
When I hold the volume (-) button and plug the cable at the phone, I got nothing more than the Windows USB sound and a red led of death on my ZL (C6503).
What I've already did:
1) Pressed the "Off" button beside the SD card slot a lot of times (holding it for a few seconds of course) before trying to get into the flashmode;
2) Tried SUS, PC Companion and Flashtool but couldn't get the flashmode or detected by any of them;
3) Keep it charging for more than 12 hours and all I got is this red led of Death!
Any help is welcome.
Cheers.
Edit:
Got the flashmode holding at the following way.
1) Pressed the "off" button beside the SD card slot for a few seconds and instead the 3 vibrations the red led blinked 3 times;
2) Hold the volume (-) button, connected the USB cable and keep holding for a lot of seconds, you will hear the Windows USB sound disconnecting and connecting a few times, wait until Flashtool recognize it and start flashing.

[Q] [HELP NEEDED] desire hd bootloader won't open

I have a desire hd which was previously at Android 2.3 Sense 2.1. I used AAHK2 fastboot mode to install custom unlocked hboot. After custom hboot was installed, I downloaded the official update for Sense 3.0 Android 2.3.5. The update downloaded and booted into recovery and it stuck on the recovery. After some time, the stuck still remained so I removed the battery and tried to reboot into bootloader but instead of bootloader, the same recovery opens which is stuck. Please help sorry for my bad english.
Bootloader not opening nor phone showing any response when I connect it to PC in semi-recovery state.
can you more cleared explained what do you mean by "semi recovery state"?
is the phone still can turn it on..?
what happen while you tried pressing and holding vol down+power button...?
JJeamy said:
can you more cleared explained what do you mean by "semi recovery state"?
is the phone still can turn it on..?
what happen while you tried pressing and holding vol down+power button...?
Click to expand...
Click to collapse
Thanks for your reply, I have attached the screenshot to show you what I mean by semi-recovery state. When I tried pressing the Vol Dn + Power button, the screenshot I attached appears. Also, I wanted to tell you that before applying the official update, I used AAHK 2 to attain S-OFF and SuperCID on my device :'(
coolyahya said:
Thanks for your reply, I have attached the screenshot to show you what I mean by semi-recovery state. When I tried pressing the Vol Dn + Power button, the screenshot I attached appears. Also, I wanted to tell you that before applying the official update, I used AAHK 2 to attain S-OFF and SuperCID on my device :'(
Click to expand...
Click to collapse
you shouldn't be flashing official again after gaining s-off with AAHK2 script...
did the green bar off flashing process that you already say is semi recovery..did you ever tried waiting that bar until finish..?, or is just stuck in the half process like in your screen shot..?
if the process bar is not ever finish..just tried removed your battery..then removed your sdcard too..then put it in back again just your battery (leave the sdcard out)..then try it to booting your phone to the bootloder with pressing and hold vol down+power again..just let me know what happen..?
JJeamy said:
you shouldn't be flashing official again after gaining s-off with AAHK2 script...
did the green bar off flashing process that you already say is semi recovery..did you ever tried waiting that bar until finish..?, or is just stuck in the half process like in your screen shot..?
if the process bar is not ever finish..just tried removed your battery..then removed your sdcard too..then put it in back again just your battery (leave the sdcard out)..then try it to booting your phone to the bootloder with pressing and hold vol down+power again..just let me know what happen..?
Click to expand...
Click to collapse
The green loading bar always stucks when I power on the phone (left for almost 1 hour), and the same semi-recovery state opens after I removed sd card and battery and pressed the Vol Dn+Power
coolyahya said:
The green loading bar always stucks when I power on the phone (left for almost 1 hour), and the same semi-recovery state opens after I removed sd card and battery and pressed the Vol Dn+Power
Click to expand...
Click to collapse
did you already tried connecting your phone to pc..while the phone is in that position..?, did the computer detected your phone..i mean is it adb or fastboot command work while in there..?
JJeamy said:
did you already tried connecting your phone to pc..while the phone is in that position..?, did the computer detected your phone..i mean is it adb or fastboot command work while in there..?
Click to expand...
Click to collapse
Yeah also tried that :'( . Computer not giving response. Also if I press vol Up + power, a red led blinks, if I press Vol Up+Vol Dn + Power button, a stable yellow LED lights up and if I connect my cell to the PC in such state, a Qualcomm CDMA notification pops up in my PC as "driver not found'
coolyahya said:
Yeah also tried that :'( . Computer not giving response. Also if I press vol Up + power, a red led blinks, if I press Vol Up+Vol Dn + Power button, a stable yellow LED lights up and if I connect my cell to the PC in such state, a Qualcomm CDMA notification pops up in my PC as "driver not found'
Click to expand...
Click to collapse
did you already tried removed the battery in some of hours..maybe?, what happen after that if tried press and hold vol down+power again..?
if still can't go to bootloader..i think there's no way to fix your back to normal again...unless you brought it to the service center to do flashing of emmc chip from the beginning again..
sorry i can't help you more than this..
JJeamy said:
did you already tried removed the battery in some of hours..maybe?, what happen after that if tried press and hold vol down+power again..?
if still can't go to bootloader..i think there's no way to fix your back to normal again...unless you brought it to the service center to do flashing of emmc chip from the beginning again..
sorry i can't help you more than this..
Click to expand...
Click to collapse
Yeah I think I have to give my phone for flashing in local mobile market as the HTC service centres aren't available in my country, Anyways, thank you very much for your support

Completely unable to boot to download mode

Hi, as the title says I am completely unable to boot to download mode on my E988. I have literally tried every possible combination of button pressing but nothing works. I have tried rebooting to bootloader from cwm but that doesnt work either, all it does is reboot, show the LG logo, then it reboots normally.. I have tried using terminal emulator to use the command "reboot download" but it doesnt work either, all it does is reboot, show the LG logo, then it reboots normally again. It seems that I am completely unable to access it at all. Any ideas?
Have you try with one end of the usb cord already plug in either your computer or phone, hold down both volume buttons, and plug in the other end. This was the only way down load mode would came on for me until I fixed the phone.
Yup I have. No combination of keys and button pressing seems to work for me it's odd.
Sent from my LG-E988 using XDA Free mobile app
To add on to my previous post, when I do the method whereby I hold vol + and vol - and plugging the usb cord in without my phone's battery, a message shows up when it is detected saying that a "...usb device has malfunctioned...". My phone will then just keep showing the lg logo over and over again causing the message to pop up again and again as the phone is detected and then not detected and the cycle just repeats itself. I have tried to reinstall lg drivers but nothing seems to work...
Edit: It would seem that the phone is indeed trying to boot to download mode whether I use the key combination or command, but it is unsuccessful in doing so and just reboots. Has anyone ever encountered this problem?
i can't access download mode on my lg f240l
guys please help me
i have tried to install a cwm on my lf but when i tried to restart it boots up and stopped on lg logo
i want to use flash tool i have the dll and tot file bot i can't access download mode (does not work vol + and connecting it with usb)
and when you start the power button menu and back keys blinking
Does anyone know what to do?
sllavy said:
i can't access download mode on my lg f240l
guys please help me
i have tried to install a cwm on my lf but when i tried to restart it boots up and stopped on lg logo
i want to use flash tool i have the dll and tot file bot i can't access download mode (does not work vol + and connecting it with usb)
and when you start the power button menu and back keys blinking
Does anyone know what to do?
Click to expand...
Click to collapse
i made it
1 pulled out the battery
2 press volume key up and down(at the same time)
3 plug the usb
and it worked !!!!
happy with download mode and flash tool
sllavy said:
i made it
1 pulled out the battery
2 press volume key up and down(at the same time)
3 plug the usb
and it worked !!!!
happy with download mode and flash tool
Click to expand...
Click to collapse
I have tried that at least a 100 times (I really did) but it doesnt work for me...
Me too, I'm having the same problem, I'm totally unable to get into download mode using standard methods (vol up/down, battery in, battery out etc etc)
dkusnierz said:
Me too, I'm having the same problem, I'm totally unable to get into download mode using standard methods (vol up/down, battery in, battery out etc etc)
Click to expand...
Click to collapse
I have the same problem, and I don´t know what to do. I get lost.....
I can understand why this happend. It should be a simple way to enter in download mode, but nothing results. I´m almost crazy...
Rucosta said:
I have the same problem, and I don´t know what to do. I get lost.....
I can understand why this happend. It should be a simple way to enter in download mode, but nothing results. I´m almost crazy...
Click to expand...
Click to collapse
Please help. I am stuck too... No download mode is insane

Just another person who has Hard Bricked his M8

Hello Everyone
TL;DR Screen doesn't come on at all, battery led only flashes while it is rebooting (More details below), and When plugged in to my windows pc, a bunch of "Local Disk Found" pop up, some of the volumes I can access, most I cannot.
I have searched and searched the internet the past 24 for solutions, and have yet to find one. So imma walk you through what led up to the issue, as well what solutions I have tried.
Yesterday while I was trying to update my rom, I ended up getting stuck in what I thought was a boot loop. I then decided to hard reset my phone and go into recovery in hope to try to reinstall the rom. To my surprise, I could not access the internal sd card in the phone. Data was unmounted in the "Mount" settings and I could not what so ever remount it. After this I tried to side load it, but to no avail.
In response to all my attempts to fix the phone at that point, in frustration, I just said "**** it" and went into factory reset in the bootloader. This is where the hard brick happened. At this point, the screen would not come one, and the battery led was not lit when plugged in. I tried letting my phone charge over night and then, tried the "Battery Recalibrate method". I then tried the "Hold Pwr + Volume up for 10 seconds, then Power + volume Down until you access the bootloader"
After that, I then thought that the firmware was corrupted, so I tried to see if I could push an img to the phone, however fastboot does not see the device. I tried RUU, it does not see the device. I tried the HTC Unbrick method by Dexter that required me to install ubuntu and do some things in terminal, that also did not find the device. And here I am stuck. One thing unique to my situation that I have yet seen reported in the countless threads I have searched, is that when I plug my phone to my pc, a large amount of disk drives are found. Most of them are not accessible, but there are a couple that I can go in and see files for. Windows asks me if I want to format the ones I can't access. When hooked to my pc, I tried the the Power + volume button combinations, the only thing that seems to happen off of this is that my phone seems to reboots, and the battery indicator briefly shows.
Anyways, this is all I can remember. Any help would be GREATLY appreciated. I don't really think it is a hardware related issue since my phone does somewhat boot. However it seems it can't get to a bootloader what so ever.
Try holding power and vol up for a long time, like a minute or more. Try with and without charger attached, and after sitting on charger overnight.
If the bootloader is intact, the phone is likely not truly bricked (recoverable). And I don't see how you could have damaged hboot by the actions you mentioned.
What is the phone's original CID (carrier version) and are you s-on or s-off?
redpoint73 said:
Try holding power and vol up for a long time, like a minute or more. Try with and without charger attached, and after sitting on charger overnight.
If the bootloader is intact, the phone is likely not truly bricked (recoverable). And I don't see how you could have damaged hboot by the actions you mentioned.
What is the phone's original CID (carrier version) and are you s-on or s-off?
Click to expand...
Click to collapse
Verizon is the carrier version, and I am s-off.
Held vol + up for 5 minutes both with and without the charger. One time with the charger into my computer, and another into the wall. When it was in my pc, I can tell its doing nothing but rebooting over and over by the notification sound, and the constant "Found new disk" notifications I got. However still no luck, no screen turns on, no sign of hboot. I'm hoping to have some luck after leaving it on charge overnight and trying again.
TheBizkit said:
Held vol + up for 5 minutes both with and without the charger. One time with the charger into my computer, and another into the wall. When it was in my pc, I can tell its doing nothing but rebooting over and over by the notification sound, and the constant "Found new disk" notifications I got. However still no luck, no screen turns on, no sign of hboot. I'm hoping to have some luck after leaving it on charge overnight and trying again.
Click to expand...
Click to collapse
So still nothing after leaving it on charge overnight and I held vol + up for about 5 minutes. Things seem grim.
I think the proper thing to do when you discovered internal storage was not mountable, would have been to use the TWRP option to format internal storage (in Advanced Wipe options).
But now I'm baffled as to what happened that would have rendered the phone unable to boot into fastboot mode. Fastboot won't recognize the device if you can't boot into fastboot mode, which leaves use kinda stuck.
So you didn't try to flash anything during the course of all this troubleshooting?
What you did - "Hold Pwr + Volume up for 10 seconds, then Power + volume Down until you access the bootloader" is totally wrong
I used to get this bunch of local disk pop-up and this is how I get out the problem
Connect the device to pc, you can hear notification sound on pc that device is connected. Ignore all those bunch of local disk pop-up
Press & hold both power button & volume up button until you hear another notification sound that device is disconnected from PC (that's the indication that device is restarted)
Release both power & volume up button and quickly press & hold volume down button (only this one button)
This should get you on bootloader
redpoint73 said:
I think the proper thing to do when you discovered internal storage was not mountable, would have been to use the TWRP option to format internal storage (in Advanced Wipe options).
But now I'm baffled as to what happened that would have rendered the phone unable to boot into fastboot mode. Fastboot won't recognize the device if you can't boot into fastboot mode, which leaves use kinda stuck.
So you didn't try to flash anything during the course of all this troubleshooting?
Click to expand...
Click to collapse
No, nothing was flashed except the original Rom update that got this snowball rolling (Not saying its the roms fault, most likely mine).
ckpv5 said:
What you did - "Hold Pwr + Volume up for 10 seconds, then Power + volume Down until you access the bootloader" is totally wrong
I used to get this bunch of local disk pop-up and this is how I get out the problem
Connect the device to pc, you can hear notification sound on pc that device is connected. Ignore all those bunch of local disk pop-up
Press & hold both power button & volume up button until you hear another notification sound that device is disconnected from PC (that's the indication that device is restarted)
Release both power & volume up button and quickly press & hold volume down button (only this one button)
This should get you on bootloader
Click to expand...
Click to collapse
This is the one combination I forgot to mention in the op, sorry for that.
But I have tried this, before and after your post, still no luck.
If it worth mentioning, I can just hold power + down and it still reboots over and over. As well as just power. As a matter of fact, all button combinations reboot the phone over and over.
TheBizkit said:
If it worth mentioning, I can just hold power + down and it still reboots over and over. As well as just power. As a matter of fact, all button combinations reboot the phone over and over.
Click to expand...
Click to collapse
I thought the screen was dead? If so, how do you know its rebooting?
redpoint73 said:
I thought the screen was dead? If so, how do you know its rebooting?
Click to expand...
Click to collapse
By it constantly connecting and disconnecting from my pc. If that doesn't mean its rebooting, then I guess I'm mistaken.
TheBizkit said:
By it constantly connecting and disconnecting from my pc. If that doesn't mean its rebooting, then I guess I'm mistaken.
Click to expand...
Click to collapse
Well, it might mean that.
If it in fact is rebooting over and over on its won, simply holding the vol down button for a long time, should put you into bootloader (on the next reboot "cycle"). Again, assuming it is in fact rebooting, and that bootloader is intact.

ZE551ML keeps vibrating, won't start.

Hi everyone,
Yesterday, as usual, i plugged my zenphone to its charger, but it almost instantly turned off and won't restart since.
The phone keeps vibrating every minute as if it was booting, but the screen doesn't light up, nor the led while charging.
I've read a lot of thread with similar problems, which were solved by replugging the battery, but this solution won't work for me.
Here is what i've tried so far:
-Changing the charger/cable
-Replugging the battery
-Leaving the battery unplugged over night, then replug
-Leaving the phone rest for 8 hours
-Pressed every possible combination of button for 20 sec
None of the above solutions changed anything.
I don't think that it could be a battery problem, the phone shut down at arround 40% and my multimeter still indicates a voltage of 4.20V at the battery.
Hope you guys will be able to help me !
Thanks
4.2 means battery more than 80 percent. you seems bricked. use the following guide step by step read everything carefully. any question post there in the thread. please search around before starting new thread.
https://forum.xda-developers.com/zenfone2/help/thead-bricked-phone-updating-to-mm-tips-t3452785
@Solasmeryl
Was you in M when you bricked ?
If you was and are getting 'continuing to os ' error in xFSTK .
Try this > in xFSTK
1) fwr dnx = your normal file you used before
2)Ifwi = try this >
http://www.mediafire.com/file/xjhv9gfiv5sn7xx/tmp_17491-ifwi_ann_a0-mofd_v1-ze551ml1929259488.bin
3) is skipped = per usual
4) OS = your usual posignbin you used before
If you get bootloader now , it will be 0094.0183 for M , flash M raw file.
Then you flash M raw file (twice) in AFTools, raw M = 4.21.40.184
First flash for approx 3 to 4 mins, where on-screen cmds pauses on "RESULT=OK" on phone.
Close flashtools , force close.
Open flashtools again , input raw , press vol+ (once) and serial now is corrected , flash till it boots into system.approx 8 mins
Notes..
If serial number is correct after xFSTK flash , you only flash raw once only. Flash Twice if serial is 0123456789ABCDEF
.
.
When connecting to xFSTK. Connect data lead.
Press power and vol-, press download , connect phone, release vol- and power
If fail , press vol + and power till first of two vibes , release buttons , hit download button in xFSTK at the same time you release buttons on phone , tricky but you can do it .
There's AFT and links to needed files in my unbrick thread in my signature , even a video showing flashing procedure
Fixed LINK , added M .184 ifwi for xFSTK
@timbernot
Hi, thank you for helping me out, i didn't though my problem could be a brick, but my symptoms are the same.
I was running CM 13, so yeah, the android version was M.
I tried your IFWI file but it doesn't seem to have fixed anything, except, the phone doesn't vibrate anymore now.
I don't know i just accidentally destroyed the vibration motor or if the IFWI file has anything to do with it.
Solasmeryl said:
@timbernot
Hi, thank you for helping me out, i didn't though my problem could be a brick, but my symptoms are the same.
I was running CM 13, so yeah, the android version was M.
I tried your IFWI file but it doesn't seem to have fixed anything, except, the phone doesn't vibrate anymore now.
I don't know i just accidentally destroyed the vibration motor or if the IFWI file has anything to do with it.
Click to expand...
Click to collapse
Nothing to do with Motor i`m afraid
Battery dead , will be the main cause .
Leave connected to charger for a good few hrs :good:
Each flash in xFSTK uses approx 10% battery , more if you sit there watching it `continuing to os`
See my video in link -- the button process and connection -- i do it just the once , admittedly i have unbricked many zens and know exactly when to press dload in xFSTK :good:
https://www.youtube.com/watch?v=PmbRaJijIBs&feature=youtu.be
ps cm13 was based on LP mainly , only the latter versions and cm 14 had bootloader upgrades.
So return to original flashing files
Solasmeryl said:
@timbernot
Hi, thank you for helping me out, i didn't though my problem could be a brick, but my symptoms are the same.
I was running CM 13, so yeah, the android version was M.
I tried your IFWI file but it doesn't seem to have fixed anything, except, the phone doesn't vibrate anymore now.
I don't know i just accidentally destroyed the vibration motor or if the IFWI file has anything to do with it.
Click to expand...
Click to collapse
Just FYI, if you were on cm13 official then your base was LP not MM. Even though it's an MM rom
Sent from my ASUS_Z00A using Tapatalk
timbernot said:
Nothing to do with Motor i`m afraid
Battery dead , will be the main cause .
Leave connected to charger for a good few hrs :good:
Each flash in xFSTK uses approx 10% battery , more if you sit there watching it `continuing to os`
See my video in link -- the button process and connection -- i do it just the once , admittedly i have unbricked many zens and know exactly when to press dload in xFSTK :good:
https://www.youtube.com/watch?v=PmbRaJijIBs&feature=youtu.be
ps cm13 was based on LP mainly , only the latter versions and cm 14 had bootloader upgrades.
So return to original flashing files
Click to expand...
Click to collapse
Ok, so i charged up the phone, went back to the original file as suggested. Vibrations are back, but i still can't figure out how to pass the "Continuing to OS" error :/
Here is how i seem to understand the steps:
1. I Click begin download (which start the 120sec timer)
2. I press Power and Vol - for 4 sec then release
3. I Connect the phone to the PC, hear the windows "device connect" sound
4.Messages show up in xFSTK, sometimes errors, sometimes the download begins, and back to the "Continuing to OS"
5.The phone vibrates, the software attemps 20 reconnect then aborts.
I've also tried a lot of different combinations such as pressing power after plugging, not pressing power at all, etc (The software indicates 41 tries).
It just seems that the phone is completely dead :/
Thans a lot for the help, i really hope that i doesn't bother you too much by making mistakes !
Do you usual flash , soon as you see continuing to os Press power and vol + , at first of of two vibes - release and hit download.
Note , if only one vibe , re press and keep pressed vol+ and power immediately.
Do press download first like in the video..but you have to double click it to stop and to begin again at the exact time of releasing at first of two vibes
Ps , depending on pc speeds etc etc , it is wise to come off the internet , disable anti virus , clean pc from junk, c cleaner free is good and do a reboot.
Also , some people report it just flashing after hrs of failures by just leaving phone connected after a failure with xFSTK still open, then restarting flash after a good break of half hr plus
@Solasmeryl
Hows it going ??
timbernot said:
@Solasmeryl
Hows it going ??
Click to expand...
Click to collapse
No change :/ even tho i've tried every button timing possible i guess.
I've noticed that pressing Power and Vol- before plugging in the phone always leads to an error. The only way to get to the continuing to os is by pressing these buttons while the phone is already connected, and then hit download.
Could there be any other software problem that could **** things up and that i forgot to mention ?
Solasmeryl said:
No change :/ even tho i've tried every button timing possible i guess.
I've noticed that pressing Power and Vol- before plugging in the phone always leads to an error. The only way to get to the continuing to os is by pressing these buttons while the phone is already connected, and then hit download.
Could there be any other software problem that could **** things up and that i forgot to mention ?
Click to expand...
Click to collapse
Can you ignore xFSTK for a moment
try this without being connected to pc either.
(A)Press and keep pressed power and vol+ . Does your phone vibrate (twice) ?
timbernot said:
Can you ignore xFSTK for a moment
try this without being connected to pc either.
(A)Press and keep pressed power and vol+ . Does your phone vibrate (twice) ?
Click to expand...
Click to collapse
Yes, the phone vibrates twice
Solasmeryl said:
Yes, the phone vibrates twice
Click to expand...
Click to collapse
Well , somehow you gotta release both buttons and hit download at the same time at first vibrations of the two .
Do what you need regarding pressing power and vol- to connect initially . Then go about trying to get the above two vibes process while downloading . Be fast to double click download at the first of two vibes --
Thats it !
That is all anyone has to do :good:
One other thing to try is - just try power , on its own(like power off), press and keep pressed after initial connection download process, once it vibrates - release and -- go for the power and vol+ 2 vibe process again. Get ready to hit download !
---------- Post added at 05:42 PM ---------- Previous post was at 05:25 PM ----------
If that doesnt work ^^^ i will begin to start asking questions about the settings you have applied
Double check this ->
(fast forward to 18:30 mins in of this video for settings to be modified in XFSTK re... changing GP over ride to 0x80000807 ) . Make sure you modified the correct CRC+ box at the bottom
https://www.youtube.com/watch?v=PmbRaJijIBs&feature=youtu.be
timbernot said:
Well , somehow you gotta release both buttons and hit download at the same time at first vibrations of the two .
Do what you need regarding pressing power and vol- to connect initially . Then go about trying to get the above two vibes process while downloading . Be fast to double click download at the first of two vibes --
Thats it !
That is all anyone has to do :good:
One other thing to try is - just try power , on its own(like power off), press and keep pressed after initial connection download process, once it vibrates - release and -- go for the power and vol+ 2 vibe process again. Get ready to hit download !
---------- Post added at 05:42 PM ---------- Previous post was at 05:25 PM ----------
If that doesnt work ^^^ i will begin to start asking questions about the settings you have applied
Double check this ->
(fast forward to 18:30 mins in of this video for settings to be modified in XFSTK re... changing GP over ride to 0x80000807 ) . Make sure you modified the correct CRC+ box at the bottom
https://www.youtube.com/watch?v=PmbRaJijIBs&feature=youtu.be
Click to expand...
Click to collapse
Hi, sorry for the delay, i had a lot of work the past two days.
I've tried everything you said, double checked every parameter, and even tried the manipulation on another computer, but there is no change.
The weird thing is, that if i plug the phone into the computer, it gets detected, but there is no vibe, so no way to know when to click on download. I only get vibes on boot if it is not connected in USB.
Moreover, i don't really understand what you mean by " double click at the first 2 vibes", since the button gets "gray" after 1 press, and there is no way to double click it.
I'm sorry, you have put a lot of effort into helping me, but i really think that my phone may be more damaged than a simple brick :/
Solasmeryl said:
Hi, sorry for the delay, i had a lot of work the past two days.
I've tried everything you said, double checked every parameter, and even tried the manipulation on another computer, but there is no change.
The weird thing is, that if i plug the phone into the computer, it gets detected, but there is no vibe, so no way to know when to click on download. I only get vibes on boot if it is not connected in USB.
Moreover, i don't really understand what you mean by " double click at the first 2 vibes", since the button gets "gray" after 1 press, and there is no way to double click it.
I'm sorry, you have put a lot of effort into helping me, but i really think that my phone may be more damaged than a simple brick :/
Click to expand...
Click to collapse
Hi there ,
From first line of original post >
"..............Hi everyone,
Yesterday, as usual, i plugged my zenphone to its charger, but it almost instantly turned off and won't restart since.........................."
And last reply ..........
"..........................The weird thing is, that if i plug the phone into the computer, it gets detected, but there is no vibe, so no way to know when to click on download. I only get vibes on boot if it is not connected in USB..........................."
Suggests it will be USB board /port /cable :good:
Do the same again with data cable connected to phone but not connected to anything to rule out cable :good:
sukhwant717 said:
4.2 means battery more than 80 percent. you seems bricked. use the following guide step by step read everything carefully. any question post there in the thread. please search around before starting new thread.
https://forum.xda-developers.com/zenfone2/help/thead-bricked-phone-updating-to-mm-tips-t3452785
Click to expand...
Click to collapse
sukhwant717,
I registered (not only) but basically to say thank you.
kefalva said:
sukhwant717,
I registered (not only) but basically to say thank you.
Click to expand...
Click to collapse
Glad to know it helped
timbernot said:
Hi there ,
From first line of original post >
"..............Hi everyone,
Yesterday, as usual, i plugged my zenphone to its charger, but it almost instantly turned off and won't restart since.........................."
And last reply ..........
"..........................The weird thing is, that if i plug the phone into the computer, it gets detected, but there is no vibe, so no way to know when to click on download. I only get vibes on boot if it is not connected in USB..........................."
Suggests it will be USB board /port /cable :good:
Do the same again with data cable connected to phone but not connected to anything to rule out cable :good:
Click to expand...
Click to collapse
I'm not sure to really understand your last sentence ? Do you mean like removing the 2 power cables inside the USB ?
I've tried with different USB cables, and no change either :/
Solasmeryl said:
I'm not sure to really understand your last sentence ? Do you mean like removing the 2 power cables inside the USB ?
I've tried with different USB cables, and no change either :/
Click to expand...
Click to collapse
You can now only pray it is the USB board and not Mainboard , order a new USB board and a `new` Data cable, do not use old data cables with new board just incase your phones charge port has altered pins on either or both cables or data cable has changed pins on usb or vice versa :good:
ps , make sure it is a quality data cable you order too, some sell data when only a charge cable

Categories

Resources