Develop Bugs

Boot problems - can't get to Tricolor, but boots to Android

Hello all,
I've searched and found some things, but nothing that matches my problem.
HTC Kaiser, branded Swisscom. HardSPL, I don't remember the version. Trying to get to tricolor screen, no key combo works. Camera+reset w/stylus, camera+power, even the two soft keys to reinstall the rom in memory.
After pulling the battery (and waiting more than 5 minutes) and inserting again, pushing the power button turns on the green LED, but goes no further, even after waiting up to 10 minutes. Pulling the battery, then plugging in the USB charger (without presses the power button) will flash a white screen after 7 seconds, then a pause of another 10 seconds, then the phone boots in to Android (again, without pushing the power button, just plugging in the USB cable.
Once in Android, everything works (except the factory reset, it just hangs forever). I need to install WM 6.5 ROM.
Tried the KAISDIAG.NBH and the 329 HardSPL recovery, but no reaction and still can't get to the tricolor.
One last piece of information, when I plug in the USB data cable, the phone flashes the "USB connected" message, and then repeatedly flashes it again every 3 seconds. The computer makes the USB connected sound, but no communication and the KaiserCustomRUU.exe can't see the phone.
Any suggestions to get to the tricolor? It unusual to turn on the phone by just plugging in the USB cable.
Thank you and great work.

Try power+camera+stylus pressing the reset.

A while back the charging behaviour was changed, so that now plugging in a charger, or usb, boots the phone, ( previously we could not charge if it was switched off).
Your problem of `losing` the bootloader has been seen before, but is rare, and seems to have no definite cause, the last time I remember seeing it turned out to be a faulty camera button.
Sent from my HTC Dream using Tapatalk

Thanks and one more question
Thanks Zenity.
I'll continue working on it. One quick question, is there a command in Android to force a hard reset or to the boot loader?

Camera Button
Ok, after searching more (due to Zenity's suggestion) and reading other threads, I don't think it's a faulty (Fawlty?) camera button.
Somehow, the phone takes along time to boot, and must use some info from the bootloader, as it loads Android.
But all attempts to get into the bootloader fail. I can't establish communication by USB, but I think I will focus my efforts there. I've pushed and help all the buttons in different combinations for too long.
I'll let you know, and thanks again!

Ok, done some research into way to detect that the camera button is functioning, ( since this button is vital in getting the bootloader), no luck yet, but research continues, looking at remapping the camera button using atools, just so i can get a response of some sort, ( normally the camera button does nothing in android, it's unmapped).
Edit: nope, atools won't help, won't let me remap the camera button.

Atools-keymapper remap the key only in the android GUI not in kernel so any change doesn't effect directly the kernel.

Yeah, realised that, just thought there might have been an easy way of diagnosing the camera button, to see if it was at least functioning, but if it's not enabled at kernel level then it will be difficult to test without disassembly and getting a meter on it.
Sent from my HTC Dream using Tapatalk

Update - Android.process.acore
Hey all, still trying to connect by USB to use the CustomRUU tool. Now when I plug in the USB, I get a repeating 'Process android.process.acore has stopped etc".
when I click force close, it pops up again and again.
Pulled the battery, and rebooted. Now it boots repeatedly, it shows the splash screen, right when it should go to the Android home screen, it reboots.
Any ideas? Thank you!

probable that the FC and subsequent reboot corrupted the data partition, which is known to happen when the device shuts down unexpectedly.
You can try a 'fix permissions', and 'clear dalvik cache', but normally it takes a wipe and re-install of the system, you may get away with not clearing data, but it's often safer to go for the full wipe of system and data.

[Q] Tried to install Beatmod ICS, stuck on "screensaver" usb and recovery won't work

[Q] Tried to install Beatmod ICS, stuck on "screensaver" usb and recovery won't work
Hi guys,
I've watched the n00b video and been googling for the last few hours as well as reading through various pages on the XDA forum. I've found a lot of problems that are kinda similar and tried various solutions but don't seem to be quite getting there.
Basically I had Virtuous Affinity as the OS and clockworkmod installed (should be the most up to date versions of both, they were put on no more than a week ago) as well. I also had a backup of current OS and so on on the SD card, as well as the original zip of the rom.
I decide I want to give ICS a go and so I downloaded the betamod ICS and then loaded it. It asked me if I wanted to do a dalvik cache wipe, a dalvik cache + data wipe and a third option I don't recall. I went with the dalvik cache wipe (at the time I was under the impression that was the correct course of action) then put it back in my pocket while ICS installed.
I get my phone out of my pocket later and it's kinda stuck on what looks like (but logically isn't, I'm guessing it was meant to be a splash screen type thing while ICS installed or some such) a screensaver which just loops endlessly. The only thing you can really do is take the battery out and turn her on again, in which case you once again end up in the endless screensaver loop.
I've tried booting to recovery using volume - and the power button and unfortunately it just boots straight into the looping screensaver again.
Getting a bit worried and feeling adventurous I tried seeing what I could do with ADB, however the computer seemed unable to recognise that any device was connected with ADB devices not listing anything.
I've read up a lot and I'm at a loss as to what to do - there's a rom on the SD card and there also should have been a backup but I just can't get it into recovery.
I do have the ability to view the SD card on another device and interact with it, so if there's a potential SD fix, that's certainly not out the window.
But yeah, I'm clueless how to proceed here and very green at the whole rom business. Can anyone advise what I might try to do from here? I don't care what state I end up going back to, or if I lose my data, I can get all that back, I just want the phone in some semblance of basic operation.
I'll be keeping an eye on the thread, if I've left out any pertinent data ask away and thanks in advance for anyone with a clue how I can fix this mess .
EDIT: Post may be better off in ICS thread above and I do apologise if so, I would move it but I seem unable to delete it.

Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.

ik222 said:
Remove battery for 5 seconds and then try again to boot into recovery using volume -and power button.
Click to expand...
Click to collapse
I have, it doesn't work. I've left the battery out for a fairly long period. Volume - + power still just brings it back to the "screensaver" loop.
Thanks for the suggestion though.

Turn the phone off completely; pull the battery out for a bit then replace it and don't touch anything. Don't try to turn it on. Plug the phone by usb to your pc (still turned off). At the command prompt in the folder containing adb.exe type "adb reboot recovery" - the phone should power on and go to recovery where you can wipe properly and reflash whatever you want.
You should be able to boot to recovery using the volume down + power button combo (hold the volume-down key, then press and hold the power button and keep both held until you get to the bootloader menu); the only thing that's wrong with your phone is that you've flashed one ROM over another without wiping it first, so the ROM can't load but this shouldn't affect your bootloader or recovery.
Worst case you can flash a RUU which will restore it to the official firmware; you'll then need to re-root and re-install a recovery image to be able to flash custom ROMs again.

Very helpful post, thanks! I'll try all that and see how I go, I'll post if I still have trouble.
Yeah I dunno why I can't boot to recovery it's weird. The volume button wasn't working, so I removed it and am pressing in the volume down portion of the volume button with a pen while holding down the power button. It's possible perhaps I'm not successfully depressing volume down, but I'm 99% sure I am and that that's not it. I am however doing it as you and other guides advise, depress volume down, hold it and then depress power and hold both for about three seconds, no joy!
Anyway, as said, I'll try what you're recommending and see how I go. Thanks!

hopscotchjunkie said:
At the command prompt in the folder containing adb.exe type "adb reboot recovery"
Click to expand...
Click to collapse
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.

Ethicistabdiel said:
Curious what you mean by this? Cause there's no command prompt in the folder ADB is in. Do you mean in command prompt, be in the folder, i.e. c:\abd kinda thing? I tried just loading command prompt and typing abd reboot recovery, no device detected - no joy.
Click to expand...
Click to collapse
Yeah that was what I meant; I've got a feeling that that only works when the phone is powered off if you had USB debugging activated on the phone beforehand, so if that's not working that might be why.

c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.

Accidental double post, sorry.

You need to try get into recovery mode, where you can do a full wipe and see if that fixes anything.
Firstly, remove your battery then re-install it, your phone should still be turned off at this stage. Press and hold the volume down button, then additionally press and hold the power butter, until something appears on the screen. If the bootloader appears, you can then boot into recovery from there.
If the above fails to work, report back with your results and hopefully something else will be suggested.

Ethicistabdiel said:
c:\adb
results in error: device not found.
ADB app itself is in C:\adb\platform-tools but when I try that it goes The System cannot find the path specified. I've tried cd/adb and I can get that far but I can't get to adb/platform-tools.
EDIT:
Okay, I managed to get to c:\adb\platform-tools but adb reboot recovery is still advising error: device not found. Guessing perhaps I didn't have usb debugging enabled. Are you able to suggest another work around at all? I'm happy to flash it to whatever, I don't mind losing data, just want to get it in working order again. I don't see how I can though when I seemingly don't have access to recovery or USB...hrmm, must be some way around.
Click to expand...
Click to collapse
Your only other option to get into recovery is the volume-down/power-on combination. Like I said, I can't think why that's not working unless it's related to your missing volume button (maybe it's not maintaining a constant pressure on the button when you're using whatever to press through the hole).
If you still can't get that to work, I would suggest finding a stock RUU and flashing that. It's an .exe file that runs from your PC and will return your ROM, bootloader and radio back to stock. Obviously that means you'll lose root and your custom recovery so you'll need to do all that again from scratch. There's a sticky in the dev section with a link to a thread with various RUUs (it's named something along the lines of "shipped & test ROMs" - I'll check that and link to it once I've dragged myself out of bed to the computer). You'll lose all your data, but if you took a backup beforehand you can restore that once you're back up and running.
//sent from my Desire HD using Tapatalk; all errors entirely intentional.

Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.

http://forum.xda-developers.com/showthread.php?t=824357&page=5
Guessing you mean that as far as the ruu thread. Am downloading a stock rom atm, with shaped internet till tomorrow, meh! Will see how I go. Have a feeling phone was probably Vodafone branded at stock though, so that could make for extra fiddling but yeah, fingers crossed.

If you are able too install a stock-rom you can work from their than install 4EXT recovery
touch than you doen't need the volume buttons.

I downloaded the most recent stock rom on the link above. When I try to install it though, phone off or on, it advises a USB connection error. Is this likely to be because I originally had vodafone stock and need to make a gold card, or should it still at least be recognising it? It does advise not to run any programs on the phone or anything when while installing the update, but of course, as long as my phones turned on it's stuck on the damned screensaver loop.

http://forum.xda-developers.com/archive/index.php/t-841890.html
Gonna give that a go, fingers crossed!
D'oh, just found out my mobile was Three at stock and not Vodafone, the search continues .

Gah, I'm about tearing my hair out here, I want my damned phone back . Stuck using a $79 Huwawei Vodafone thing at the moment and it's so so so awful.
Anyway. I was under the impression that making a goldcard would mean I could RUU a non-Three stock rom on the phone. I made a goldcard following these instructions; http://www.addictivetips.com/mobile/how-to-make-gold-card-for-htc-desire-hd/
Then I turned the phone on as the RUU advises, (meaning it's scrolling through the feckin' "screensaver") and start the process and once again get a USB connection error.
What's the better process at this stage, try and take it back to Three stock? I don't see how I can at the moment, the only Three stock I can find seems to be rom, not RUU, meaning I'd need to load from the phone, which I can't due to no recovery. Or should I keep trying to get the goldcard thing to work, maybe try some different RUU's or something?
I'm open to any other suggestions as well. Had a bit more of a fiddle around with my volume down button, no matter what I do though, I can't get recovery mode. Always boots first to the white HTC screen and then starts the infernal "screensaver" loop.

Ethicistabdiel said:
Yeah I'm starting to think perhaps the down button is just broken.
What state should the phone be for the RUU, turned off with usb plugged in or turned on? Bearing in mind, that when on, all it will do is the "screensaver". Will it work in either of those states?
Thanks, will deffo research more when I get home. Appreciate the help immensely.
Click to expand...
Click to collapse
How come the volume down button be broken. When you were using Affinity Rom weren't you able to use your volume button for music. Remove SD card from phone then press "First - Volume down gently for 2 sec" & press-hold power button when it goes into bootload place your sd card back select option "REBOOT RECOVERY". I think your panicking too much just be patient nothing is wrong, i think your just hurrying it up...

The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .

Ethicistabdiel said:
The volume button didn't work before either. I had to manually adjust volume from settings. I thought it was just because of the dodgy plastic button on top, but using a pen to depress the button underneath doesn't work either.
Believe me, I've been trying to fix this for days now, every different way of depressing volume down in order to get to recovery has not worked. Short of taking the phone apart and seeing if I can see what's wrong with the button (doubtful with my level of expertise) then it ain't happening via that method.
Got a little bit hopeful with this;
http://www.htcdev.com/bootloader/ruu-downloads
But that too requires my phone to be in usb debugging mode, which of course, it isn't.
Is there anyway to force the phone into usb debugging mode using some form of hack or some such? The thing is, it is powered and everything, I can turn it on, the screen works and all that jazz and indeed the phone will charge from USB and the computer makes a noise when I plug or unplug it, the phone itself however won't do anything other than the "screensaver" ICS installation loop. I guess I'm thinking where there's life there's hope and perhaps there's some way in that state I can get it to switch debugging on, though I think I'm reaching at this point .
Click to expand...
Click to collapse
The only option i can think of is "Fix your volume button from your nearest Service centre". Without that you cant do anything. I am Sorry....

[Q] My HTC Desire doesn't unlock...! Please help

Hi,
I've locked my phone yesterday and I've found a problem that doesn't let me unlock the device. I couldn't unlock and reboot the phone, so I took off the battery and placed it on and started up the phone. It freezed again on the unlocking. Tried this a couple of times - same problem. It has no wallpaper, the SD card reacts very slowly, the network also, and the screen doesn't turn off by itself if you don't do it so. Sometimes I can't even answer a call, it shows somthing like "Application not responding. Wait/Force close". I doubt it's the HTC Sense broken down or something similar. Please help me, I need my phone very quickly!
P.S. The phone is NOT rooted
Thanks!

kdervisov said:
Hi,
I've locked my phone yesterday and I've found a problem that doesn't let me unlock the device. I couldn't unlock and reboot the phone, so I took off the battery and placed it on and started up the phone. It freezed again on the unlocking. Tried this a couple of times - same problem. It has no wallpaper, the SD card reacts very slowly, the network also, and the screen doesn't turn off by itself if you don't do it so. Sometimes I can't even answer a call, it shows somthing like "Application not responding. Wait/Force close". I doubt it's the HTC Sense broken down or something similar. Please help me, I need my phone very quickly!
P.S. The phone is NOT rooted
Thanks!
Click to expand...
Click to collapse
You will lose all your data by doing this.
Boot into the bootloader (power off, press and hold volume down, press and hold power).
Wait for some green writing to appear and then disappear (about 7 seconds).
Use the volume down button to navigate to "clear storage", then press power.
Once this is done, reboot the phone and hope for the best.
----------------
If this doesn't work, make a goldcard (google how to) with any other android phone you may have, insert the goldcard in your desire
download the latest WWE RUU (look on resources in my guide)
boot into fastboot mode (hold back & power) and plug it in via USB to your PC
Run RUU.exe and do not touch the phone til it completes.

bortak said:
You will lose all your data by doing this.
Boot into the bootloader (power off, press and hold volume down, press and hold power).
Wait for some green writing to appear and then disappear (about 7 seconds).
Use the volume down button to navigate to "clear storage", then press power.
Once this is done, reboot the phone and hope for the best.
----------------
If this doesn't work, make a goldcard (google how to) with any other android phone you may have, insert the goldcard in your desire
download the latest WWE RUU (look on resources in my guide)
boot into fastboot mode (hold back & power) and plug it in via USB to your PC
Run RUU.exe and do not touch the phone til it completes.
Click to expand...
Click to collapse
Well thanks man for the work, but I'm kinda n00b at all these phone system stuff, is there any other way that has less consequences than this, I mean, no losing all the data stored?

no, not without a properly functioning device.

[Q] Phone won't boot. Vibrates three times. Need advice.

My G2 won't boot normaly and is acting very straingly. I did a search of other similar problems people have had, but nothing matches what is happening to mine. It started when I noticed my power button and volume up button stoped working. I assumed it was a glitch and thought a reboot might help. Since the power button wasn't functioning, I pulled the battery to reboot it. That's when it stoped working. When I turn it on normaly with the power button, the screen stays off, it vibrates three times, and the led blinks orange untill I put the battery. If I attempt to boot into recovery with the button combination, it does the same. If I attempt to boot into HBoot, it vibrates five times and the led lights up solid green. Here's where things get realy strange. When I plug the phone into the charger while the phone is off, after about five seconds the phone comes on into the recovery bootloader even though when I boot while holding the buttons it dosn't work. I have the ClockworkMod touch recovery installed. From within the recovery I have full access to everything including ADB with root access. When I select the reboot option from recovery, it does the same thing with the vibrating and the blinking led. I tried the key test in the recovery and I discovered that my volume up button only works intermitently and my power button seems to be working fine. I haven't attempted to flash a new rom yet because I'm assuming it must be something else since I can't even access HBoot, and I'm scared if I touch anything I'll loose access to recovery and ADB as well.
Any advice? Could a damaged volume up button contact cause all this to happen? Should I try flashing it from recovery even though I can't access HBoot?

Thread moved to Q & A section, post in the relevant section next time.

in adb try
adb reboot-bootloader

demkantor said:
in adb try
adb reboot-bootloader
Click to expand...
Click to collapse
Just tried it. Screen goes black, vibrates three times, and led blinks orange untill I pull the battey. It was a good Idea though, I didn't think to try that myself.

you know what, are these very quick vibrates? you mentioned there is a problem with your volume rocker (sticky keys?) your phone may be trying to get into the jtag/download mode.
not sure how to use this mode on the vision but tell me if this is the same response you get.
take out battery, hold both volume buttons, plug phone into computer.
it should vibrate three times rapidly and computer should look for driver :
Qualcomm CDMA Technolgies MSM driver
not sure where to get the proper driver for the vision but ive used this mode to root other android phones and i know there is a "unbricking project" for various phones that use this mode.
nothing for the vision that i know of though.
but being you have adb access maybe test a few things first like see if anything is accessible from your emmc
type:
Code:
adb shell
dmesg | grep mmc0
and see what happens
edit:
i can replicate you situation by holding volume up while powering on
you have a stuck volume up key, almost 100% just open up phone and clean it out and you should be just fine!

[Q] I can't access Bootloader or Recovery PLEASE Help!

My HTC One M8 (Verizon) is seemingly bricked. My phone is rooted, S-Off, with the stock ROM. I have been trying to update to the latest OTA update by returning to stock. I had previously modified some entries in the Build.prop and Platform.xml. I knew those had to be default in order for the OTA to work. I had copied the original files and pasted them to my SD Card so that I could simply cut the modified versions, paste them to my SD Card, and cut the originals from my SD Card and put them in their corresponding system folders.
Upon a reboot something apparently went horribly wrong because all my phone does now is boot with the white screen and green HTC Logo, then the screen goes black. I have tried the typical Power Button + Volume Down but it won't enter the boot loader. The good news is that the USB port seems to still work for my windows computer recognizes a device connecting to it but it doesn't show up as an interactive device in windows explorer..if that makes sense.
Please Help!

SF-Echo18 said:
My HTC One M8 (Verizon) is seemingly bricked. My phone is rooted, S-Off, with the stock ROM. I have been trying to update to the latest OTA update by returning to stock. I had previously modified some entries in the Build.prop and Platform.xml. I knew those had to be default in order for the OTA to work. I had copied the original files and pasted them to my SD Card so that I could simply cut the modified versions, paste them to my SD Card, and cut the originals from my SD Card and put them in their corresponding system folders.
Upon a reboot something apparently went horribly wrong because all my phone does now is boot with the white screen and green HTC Logo, then the screen goes black. I have tried the typical Power Button + Volume Down but it won't enter the boot loader. The good news is that the USB port seems to still work for my windows computer recognizes a device connecting to it but it doesn't show up as an interactive device in windows explorer..if that makes sense.
Please Help!
Click to expand...
Click to collapse
When you connect it to the PC can you pick up the device with adb? If so, have you tried to run the command from adb to boot it into bootloader? adb devices ... if found, adb reboot bootloader
:fingers-crossed:

BerndM14 said:
When you connect it to the PC can you pick up the device with adb? If so, have you tried to run the command from adb to boot it into bootloader? adb devices ... if found, adb reboot bootloader
:fingers-crossed:
Click to expand...
Click to collapse
I'm not too familiar with ADB commands but I typed in "adb reboot recovery" and it said: "error: device not found" so even if my command was wrong it's still not detecting it. I also tried: "fastboot reboot bootloader" and it just says "waiting for device"
Also I feel like it's worth mentioning the phone is automatically rebooting every two minutes or so (haven't timed it exactly but it's a while). Still showing the green HTC Logo then the screen goes dim, then the screen turns off.

SF-Echo18 said:
I'm not too familiar with ADB commands but I typed in "adb reboot recovery" and it said: "error: device not found" so even if my command was wrong it's still not detecting it. I also tried: "fastboot reboot bootloader" and it just says "waiting on device for device"
Also I feel like it's worth mentioning the phone is automatically rebooting every two minutes or so (haven't timed it exactly but it's a while). Still showing the green HTC Logo then the screen goes dim, then the screen turns off.
Click to expand...
Click to collapse
Try holding volume UP + Power button, this simulates a "battery pull", just hold it in for a while it can take a while to "pull", when it's off try again booting into bootloader, volume DOWN + Power button.

BerndM14 said:
Try holding volume UP + Power button, this simulates a "battery pull", just hold it in for a while it can take a while to "pull", when it's off try again booting into bootloader, volume DOWN + Power button.
Click to expand...
Click to collapse
I held Volume Up + Power Button and it showed the white screen with the green HTC logo. I then released all buttons. Once the screen turned off I then held Volume Down + Power Button for two minutes straight and nothing happened.
Even though we haven't found a solution yet, I am appreciative of the help.

sounds like you never installed the htc drivers for your phone, hence your pc doesn't see the phone when you are doing ADB commands.
install the drivers for it, then try the ADB commands via your pc
and dont mess with the build prop or other system files unless you have a working back up and are 101% certain about what you are doing..

Just remember to change directory in command prompt to the folder where adb.exe is located.
I don't know why the device doesn't reboot into bootloader though when you hold volume down + power button, shouldn't have to hold it for 2minutes. Holding volume up + power button to simulate a "pull" should only take up to 20 seconds or so at most and pressing volume down + power will then immediately take you into bootloader mode, or at least it's supposed to.
Did you release the volume up / power combo when the screen went dead or before? Try holding it until the phone shuts off and then right away press volume down + power.
Sorry if I'm not answering right away though, busy eating, and will be here and away for the next hour or so while I get ready for work =o( once I leave for work I'll only be able to help some more after like 2 hours or so. Hopefully we can do something before then though =o)

wase4711 said:
sounds like you never installed the htc drivers for your phone, hence your pc doesn't see the phone when you are doing ADB commands.
install the drivers for it, then try the ADB commands via your pc
and dont mess with the build prop or other system files unless you have a working back up and are 101% certain about what you are doing..
Click to expand...
Click to collapse
You're right, I didn't install the drivers. I did so and ADB was able to recognize it and I was able to access the bootloader. Thank you everyone for your help. I won't be making the mistake again.

SF-Echo18 said:
You're right, I didn't install the drivers. I did so and ADB was able to recognize it and I was able to access the bootloader. Thank you everyone for your help. I won't be making the mistake again.
Click to expand...
Click to collapse
So you'll be able to fix it from here on then? I was just about to link this thread to you as well should you have gotten adb to work again, it's for the RUU for Verizon seeing as you said you're on Verizon.
But going by your response up there you might already know how to fix this issue further :good:

BerndM14 said:
So you'll be able to fix it from here on then? I was just about to link this thread to you as well should you have gotten adb to work again, it's for the RUU for Verizon seeing as you said you're on Verizon.
But going by your response up there you might already know how to fix this issue further :good:
Click to expand...
Click to collapse
Indeed I appreciate it, but I just finished installing the RUU ha. Hopefully this thread will be of use to someone in a similar circumstance in the future.

Share another method of getting into recovery mode on non-responsive blank screen
Hi,
I just want to share how I accessed recovery mode with the same build.prop issue but with S-ON (might work with S-Off too).
I found the solution from here:
http://forum.xda-developers.com/htc...ter-download-mode-t2853100/page2#post62490577
To get into recovery mode on a non-responsive blank screen, hold the power button and volume up button at the same time and then approximately after 10 seconds, switch from pressing the volume up to volume down button before the HTC logo white screen shows while still holding down the power button. After, a white boot screen will give an option to go into recovery mode.