[Q] Should I consider this N7100 emmc is dead? - Galaxy Note II Q&A, Help & Troubleshooting

The image in the picture is the only thing it shows when I try to turn it on normally. It will get in download mode normally so I tried to flash a bootloader and ODIN said there is no PIT partition. I don't know much about samsung phones but reading some posts the only explanation I can figure is that the emmc died.
The thing is that on the download mode I can see the model and the knox count.

U r able to get into download mode......so that is not the sds or wht u say emmc dead....just flash a stohk firmware via Odin and follow the instructions properly.....make sure that u uncheck repartition. ....that shld sovle the issue.....
Hope this helps. .......cheers:good::good:
---------- Post added at 10:18 AM ---------- Previous post was at 10:12 AM ----------
Do a factory reset after flashing.......all issues solved for good

devrog17 said:
U r able to get into download mode......so that is not the sds or wht u say emmc dead....just flash a stohk firmware via Odin and follow the instructions properly.....make sure that u uncheck repartition. ....that shld sovle the issue.....
Hope this helps. .......cheers:good::good:
---------- Post added at 10:18 AM ---------- Previous post was at 10:12 AM ----------
Do a factory reset after flashing.......all issues solved for good
Click to expand...
Click to collapse
Thanks, I'll give it a try...

My international Note 2 is doing this exact same thing, it's there anyone who could help? When I try to flash with odin, it tells me No Pit Partition.
Sent from my XT1068 using Tapatalk

Dear all
You have an eMMC failure.
My Note 2 had the same issue where the product name did appear in download mode however no amount of flashing (ROM or PIT) solved the issue. ODIN always failed with the message "there is no PIT partition"
This was aslo confirmed by a workshop i sent the phone to for fixing.
Solution is new motherboard or eMMC chip replacement
Best of luck

Related

[Q] Corrupted EFS- with no restore

Hi
Last night i tired to root my phone using a firmware but kinda ran in some what a major issue. As i was updating the ROM using ODIN it decided to fail and kinda soft brick my device. After trying to find ways to get round i mange to find a stock ROM which got it back to the main screen. The issue that i've got now is that the IMEI number is 0049 and getting no service or mobile data.
Looked on a couple forums about trying to fix the IMEI. I came across one including the NV_Data and another one using EFS restore. The issue is that i haven't got a working NV_Data file or a full back up of a EFS partition. (yeah i know that i've should've backed up the EFS had it all today off my mate hehe)
Was wondering if anyone could help me or point me in the right direction.
Phone: Samsung Galaxy Note 2 GT-N7100- SIM: T-mobile
Thank you
from dr.ketam thread
http://forum.xda-developers.com/showthread.php?t=2420881
How to recover lost IMEI that happens with downgrading ROM
If you have lost IMEI just by downgrading (as said by above by flashing older ROM), still you can recover IMEI without having EFS backup.
-Again upgrade ROM will restore IMEI OR
-Flash latest Modem. You can find it here.. You can download MG1 modem and flash using PC Odin with 'Phone' tab instead of PDA.
Remember above said works only if IMEI is corrupted by downgrading ROM only, if it was corrupted by other things, this won't be helpful.
---------- Post added at 10:05 PM ---------- Previous post was at 10:03 PM ----------
try flashing DDDMG1 or DXDMF1 modem from this thread
http://forum.xda-developers.com/showthread.php?t=2044937
Thank you for the reply.
Just to double check is it this what i need to download from the link you gave me
Modem
N7100XXALJ1 (modem version N7100XXALIH) [Thnx AdamLange]
If so for some reason the file cant be found
no i meant the latest 3 modems for 4.1.2
XXDME4
DXDMF1
DDDMG1
because flashing old modem over one of the 3 newer modems makes the same problem as yours ..
so installing the newer modem might fix things for you without having to install the whole rom
-------------------
u nead a custom recovery(philz or Twrp) to install these modems ...
Really grateful for the help
When you say i need to install the modem using a recovery (philz or twrp) would you happen to know were i can find a step by step guide on how to use the recovery??
Cheers
u already used odin so u must have samsung drivers and odin ... just dowanload twrp for ur n7100 from there site http://teamw.in/project/twrp2/115
then download the Odin Method
select the file from the pda button in odin and flash ....it should even root ur phone if it wasn't .. there is a lot of ways to reset ur phone to stock so it's not a dangerous operation
this vid is for s3 but it's the same method http://www.youtube.com/watch?v=_f9QdsnSTso just use the file from the link above
OOOOOSHHHHHH!!!!!!!
Thank you very much for all help manage to get it working now. Everything you said has helped.
Cheers mate really appreciate everything you done :victory:
don't want to confuse you but if u don't want to root ur phone / install custom recovery
u can download stock rom http://forum.xda-developers.com/showthread.php?t=2230250
it should be same result ...
---------- Post added at 11:38 PM ---------- Previous post was at 11:21 PM ----------
u r welcome .....just make a nandroid backup (using the custom reecovery ) and the make sure to include the EFS and place it somewhere secure extsd and the pc to save u from alot of trouble in the future

[Q] Help With My Soft Bricked AT&T GS3?

So I flashed a rom called SlimKat, didn't like it, and tried to flash back to stock. Before though I used TriangleAway to clear my binary counter. I noticed it download mode that it says the following
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: OFFICIAL
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BIT: 1
BOOTLOADER AP SWREV: 2
and after I attempt to flash something with Odin, it will say below the bootloader thing
SW REV CHECK FAIL: FUSED 2> BINARY 0
When I try to boot regularly it gets passed the first Samsung logo, but it will get stuck at the first SlimKat logo screen.
I've tried everything that worked every other time I've bricked my phone, but this time I guess it's different. I also currently have CWM recovery if that helps anything. Also, my microSD card doesn't work anymore, but I should be getting a new one soon, just in case i can put a rom on there and flash it from CWM. Any suggestions, or should I just send it in at this point?
http://forum.xda-developers.com/showthread.php?t=1984717
---------- Post added at 05:50 PM ---------- Previous post was at 05:49 PM ----------
leave it un download Mode band plug it to kies go ti firmware restore option follow these steps ur good to go
MrFhenix said:
http://forum.xda-developers.com/showthread.php?t=1984717
---------- Post added at 05:50 PM ---------- Previous post was at 05:49 PM ----------
leave it un download Mode band plug it to kies go ti firmware restore option follow these steps ur good to go
Click to expand...
Click to collapse
didnt work. said there was an error
Did you install an AT&T OTA 4.3 update?

[Q] HELP PLS!! Bricked phone

Hello!
First, I apologize for not knowing english, I'm Brazilian.
and also because I do not know if here is the right place to post.
I have a problem, need help very much!
I'll try to explain perfectly.
I had installed TWRP;
and the rom SlimWiz SL1.
I thought about changing rom, then
I was trying to install DN3_v5.5.
I selected the TWRP, I selected to wipe cache, dalvik cache, system and data,
tried installing DN3, but do not know for what reason, did not install the file,
said that there were installers but not charged anything on the phone,
I could not add another rom to install, then hung up.
Now I can not install anything because I have no access recover, TWRP
I can only access the download mode.
When I try to install the odin the following error appears:
<ID: 0/003> Added !!
<ID: 0/003> Odin v.3 engine (ID: 3) ..
<ID: 0/003> File analysis ..
<ID: 0/003> SetupConnection ..
<ID: 0/003> Initialzation ..
<ID: 0/003> Set PIT file ..
<ID: 0/003> DO NOT TURN OFF TARGET !!
<ID: 0/003> FAIL!
<ID: 0/003>
<ID: 0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
or the following message appears when I will try to install a rom: "There is no PIT partition"
I try to use everything in ODIN.
download mode looks like this:
ODIN MODE
PRODUCT NAME: GT-N7100
CUSTOM BINARY DOWNLOAD: YES (1 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
WARRANTY BIT: 0
Does anyone know how I can revive my phone? :crying:
maskara said:
Hello!
First, I apologize for not knowing english, I'm Brazilian.
and also because I do not know if here is the right place to post.
I have a problem, need help very much!
I'll try to explain perfectly.
I had installed TWRP;
and the rom SlimWiz SL1.
I thought about changing rom, then
I was trying to install DN3_v5.5.
I selected the TWRP, I selected to wipe cache, dalvik cache, system and data,
tried installing DN3, but do not know for what reason, did not install the file,
said that there were installers but not charged anything on the phone,
I could not add another rom to install, then hung up.
Now I can not install anything because I have no access recover, TWRP
I can only access the download mode.
When I try to install the odin the following error appears:
<ID: 0/003> Added !!
<ID: 0/003> Odin v.3 engine (ID: 3) ..
<ID: 0/003> File analysis ..
<ID: 0/003> SetupConnection ..
<ID: 0/003> Initialzation ..
<ID: 0/003> Set PIT file ..
<ID: 0/003> DO NOT TURN OFF TARGET !!
<ID: 0/003> FAIL!
<ID: 0/003>
<ID: 0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
or the following message appears when I will try to install a rom: "There is no PIT partition"
I try to use everything in ODIN.
download mode looks like this:
ODIN MODE
PRODUCT NAME: GT-N7100
CUSTOM BINARY DOWNLOAD: YES (1 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
WARRANTY BIT: 0
Does anyone know how I can revive my phone? :crying:
Click to expand...
Click to collapse
This does not happen unless you are careless with the given processes. I have flashed custom ROM for over 30 times and have never faced a problem.
Anyway, flash pit file for your device via ODIN.
Then install stock ROM via ODIN.
If pit file flashing fails, report back with error.
Sent from my GT-N7100 using Tapatalk
ceomaverick said:
This does not happen unless you are careless with the given processes. I have flashed custom ROM for over 30 times and have never faced a problem.
Anyway, flash pit file for your device via ODIN.
Then install stock ROM via ODIN.
If pit file flashing fails, report back with error.
Sent from my GT-N7100 using Tapatalk
Click to expand...
Click to collapse
using the pit file I got the following error:
<ID: 0/005> Added !!
<ID: 0/005> Odin v.3 engine (ID: 5) ..
<ID: 0/005> File analysis ..
<ID: 0/005> SetupConnection ..
<ID: 0/005> Initialzation ..
<ID: 0/005> Set PIT file ..
<ID: 0/005> DO NOT TURN OFF TARGET !!
<ID: 0/005> Get PIT for mapping ..
it stops running at this time
maskara said:
using the pit file I got the following error:
Added !!
Odin v.3 engine (ID: 5) ..
File analysis ..
SetupConnection ..
Initialzation ..
Set PIT file ..
DO NOT TURN OFF TARGET !!
Get PIT for mapping ..
it stops running at this time
Click to expand...
Click to collapse
If you can go to download mode at all, means your phone is soft bricked. Pit file should always work...no reason not to.
I guess you have a broken cable that is causing problems.
Does your phone charge when its off...showing green battery logo?
Also, which ODIN version you are using?
Also, tell me which firmware you are using to flash via ODIN?
Also, before brick was your phone running 4.1.2 or 4.3 or 4.4.2?
Post back.
Sent from my GT-N7100 using Tapatalk
ceomaverick said:
If you can go to download mode at all, means your phone is soft bricked. Pit file should always work...no reason not to.
I guess you have a broken cable that is causing problems.
Does your phone charge when its off...showing green battery logo?
Also, which ODIN version you are using?
Also, tell me which firmware you are using to flash via ODIN?
Also, before brick was your phone running 4.1.2 or 4.3 or 4.4.2?
Post back.
Sent from my GT-N7100 using Tapatalk
Click to expand...
Click to collapse
My Phone is soft bricked too... i need .pit file can you link it?
Shady95 said:
My Phone is soft bricked too... i need .pit file can you link it?
Click to expand...
Click to collapse
8gb?
16gb?
32gb ?
Sent from my GT-N7100 using Tapatalk
ceomaverick said:
8gb?
16gb?
32gb ?
Sent from my GT-N7100 using Tapatalk
Click to expand...
Click to collapse
16gb
Shady95 said:
16gb
Click to expand...
Click to collapse
Link:
http://forum.xda-developers.com/showthread.php?t=1927983
If this does not work. Try to flash 4.4.2 Stock ROM. Of that too fails, you have to get it repaired.
Sent from my GT-N7100 using Tapatalk
Hi I know how irritating soft brick is, I have done it twice and both times I got my phone back using KIES by Samsung.
You can do initialization of the Firmware using an option under tools in KIES, it will ask for ur model number and Serial number. It will install Stock ROM back on your phone with Stock Recovery, just follow the on screen instructions!!
I have done it twice and I think it should work for you too!!.
Let us know if you find another solution!!
ceomaverick said:
Link:
http://forum.xda-developers.com/showthread.php?t=1927983
If this does not work. Try to flash 4.4.2 Stock ROM. Of that too fails, you have to get it repaired.
Sent from my GT-N7100 using Tapatalk
Click to expand...
Click to collapse
i have to use .pit file alone or with PDA?
---------- Post added at 08:32 PM ---------- Previous post was at 08:14 PM ----------
arbaheti said:
Hi I know how irritating soft brick is, I have done it twice and both times I got my phone back using KIES by Samsung.
You can do initialization of the Firmware using an option under tools in KIES, it will ask for ur model number and Serial number. It will install Stock ROM back on your phone with Stock Recovery, just follow the on screen instructions!!
I have done it twice and I think it should work for you too!!.
Let us know if you find another solution!!
Click to expand...
Click to collapse
Kies said that is impossible upgrade this device
Shady95 said:
i have to use .pit file alone or with PDA?
---------- Post added at 08:32 PM ---------- Previous post was at 08:14 PM ----------
Kies said that is impossible upgrade this device
Click to expand...
Click to collapse
Chose as a pit file ...There is a pit tab in odin 3.07 or 3.09.
Sent from my GT-N7100 using Tapatalk
Shady95 said:
i have to use .pit file alone or with PDA?
---------- Post added at 08:32 PM ---------- Previous post was at 08:14 PM ----------
Kies said that is impossible upgrade this device
Click to expand...
Click to collapse
Dont upgrade... there is an option of Initialize firmware, it will take you back to Stock ROM!
Step by step solution!!
Shady95 said:
i have to use .pit file alone or with PDA?
---------- Post added at 08:32 PM ---------- Previous post was at 08:14 PM ----------
Kies said that is impossible upgrade this device
Click to expand...
Click to collapse
I have done it twice so I think it shouldn't be a problem but let me guide you through it:
Install KIES and follow steps below
Step 1 : Click on Tools > Firmware Upgrade & Initialisation
Step 2: Enter Device information > Model Name and click OK.
Step 3: Enter Device's Serial Number (its in the battery compartment, you need to remove battery and note down the S/N)
Step 4 : Read the information and click OK
Step 5 : It will show you the available firmware available and ask to confirm
Step 6 : It will download components
Step 7 : Agree to terms and conditions and you are good to go!
arbaheti said:
I have done it twice so I think it shouldn't be a problem but let me guide you through it:
Install KIES and follow steps below
Step 1 : Click on Tools > Firmware Upgrade & Initialisation
Step 2: Enter Device information > Model Name and click OK.
Step 3: Enter Device's Serial Number (its in the battery compartment, you need to remove battery and note down the S/N)
Step 4 : Read the information and click OK
Step 5 : It will show you the available firmware available and ask to confirm
Step 6 : It will download components
Step 7 : Agree to terms and conditions and you are good to go!
Click to expand...
Click to collapse
kies show "the version of the device cannot be updated"
---------- Post added at 12:57 PM ---------- Previous post was at 12:54 PM ----------
ceomaverick said:
Chose as a pit file ...There is a pit tab in odin 3.07 or 3.09.
Sent from my GT-N7100 using Tapatalk
Click to expand...
Click to collapse
didn't work
Shady95 said:
kies show "the version of the device cannot be updated"
---------- Post added at 12:57 PM ---------- Previous post was at 12:54 PM ----------
didn't work
Click to expand...
Click to collapse
Have you tried downloading Stock ROM and falsh it using ODIN??
arbaheti said:
Have you tried downloading Stock ROM and falsh it using ODIN??
Click to expand...
Click to collapse
yes but didn't work
Shady95 said:
yes but didn't work
Click to expand...
Click to collapse
Where did you download the Stock ROM from?
Have you tried one from sammobile.com ???
I have soft bricked my note 2 at least 5-7 times in past 2 years and the best solution I had was from KIES, second Best was Stock ROM from sammobile.com flashed via odin!!
arbaheti said:
Where did you download the Stock ROM from?
Have you tried one from sammobile.com ???
I have soft bricked my note 2 at least 5-7 times in past 2 years and the best solution I had was from KIES, second Best was Stock ROM from sammobile.com flashed via odin!!
Click to expand...
Click to collapse
yes i downloaded the ROMs from sammobile
Shady95 said:
yes i downloaded the ROMs from sammobile
Click to expand...
Click to collapse
can you tell me how did you try to flash Stock ROM??
Which ODIN are you using ( I used V 3.07)!
Oi, vou tentar te ajuda.
Me diz qual o modelo seu aparelho?
E a versao 4g?
---------- Post added at 05:52 PM ---------- Previous post was at 05:38 PM ----------
http://forum.xda-developers.com/showthread.php?t=2745828
Tente por aqui
Baixe este odin
E o recorvery, tente
Se nao der baixa a rom, tenta novamente.
Se nao der tem a opção mas arriscada que envolve abrir o aparelho e da um curto em um resitor

Help With Root and Going Back To Stock Firmware Problems N910p

Hey guys im kinda new here and english isnt my native language so mind the punctuation and bad english
so here goes
I have a Note 4 910p which was working fine until i decided to root it with the cf-root method for note 4 available on XDA . everything went fine but i needed root to install few ported stuff from other brands. I wanted to install a ported SONY XPERIA CAMERA , for that i needed a recovery i installed a CWM recovery , i installed the camera and after flashing it and finishing of the work , in the end it asked me if i wanted to root. i didnt know what to do i click okay. so it rooted after that my cell booted and the touch calibration was off . i fixed that by *#2663# code .
the main problem im facing is that after the whole process i cannot install any apks, like i can click the install button but as soon as it starts installing i get an error "App not installed . Package may be corrupted" i thought it was with just one apk file. i tried multiple apks on my cell and other cells. its working on other cells but not on mine. secondly i cannot seem to activate the Private Mode no matter how much i try. i have tried factory resetting it from the OS. ive tried factory reseting it from the CWM recovery. everytime i factory reset the calibration goes whack.
I downloaded 2 different STOCK FIRMWARD Tar files but every time i try installing them , its starts installing and ends with
AUTH Fail in Odin
Please help me.
PS : The Camera Apps From XPERIA package stay no matter how many times i factory reset please help
if it helps i cant post images but i can give u the spec and other details of my cell if it can help u people in understanding my problem
Bootloader
N910PVPS4DPE2
PDA VERSION
N910PVPS4DPE2
CSC VERSION
N910PVPS4DPE2
KERNEL VERSION
3.10.40-7972192
[email protected] #1
32-BIT
Try a different version of odin s9me times when I odin stock tar it takes a couple times for it to stick on latest tar I think I use odin 3.10.7 other way you can go is odin twrp recovery put a stock rom (look for one's by tx)on SD card boot into recovery flash tx's rom and reboot
I have tried it what I wanna know is how can I unroot and flash stock firmware because when I flash with Odin it gives me error
Fail auth something
Flash An ok1 tar then take ota
I meant ok1 stock rom
So you must odin ok1 bb and bl
---------- Post added at 11:34 PM ---------- Previous post was at 11:28 PM ----------
Are you pulling battery out and waiting 20 sec before you boot to download mode?
---------- Post added at 11:36 PM ---------- Previous post was at 11:34 PM ----------
I see you have cwm try flashing twrp
---------- Post added at 11:37 PM ---------- Previous post was at 11:36 PM ----------
You can find a zip for twrp so you don't have to use odin
---------- Post added at 11:44 PM ---------- Previous post was at 11:37 PM ----------
If you just want 100%stock you will need odin so keep trying deferent version of odin, reboot pc and start fresh also boot into download after you pull the battery
Because if you want to use Kies you will need stock recovery even for ota's you need stock recovery so best bet is to get odin to work properly
thank u guys for ur quick response. i couldnt find the proper solution for the APK and Private Mode problem but i did manage to find the solution for going back to stock
What i was doing wrong was that i had the OTA update upto 6.01 and i was trying to flash a 5.0 firmware tar . i was researching where i came across that after the 5.01 update u cant downgrade to older one thats y i was facing the
AUTH Fail
Error while using ODIN thank u all for ur help and suggestions

Hard brick!! Help!!!

my note 4 sm-n910v does not do anything,only when i conect it to the computer shows up QHS_BULK.
I already tried unbrick image and now i can but into download mode but when i try to flash with PDA and PIT i got e_mmc write filed.
What can i do?
alfrecuba said:
my note 4 sm-n910v does not do anything,only when i conect it to the computer shows up QHS_BULK.
I already tried unbrick image and now i can but into download mode but when i try to flash with PDA and PIT i got e_mmc write filed.
What can i do?
Click to expand...
Click to collapse
You shouldnt be flashing pda bro , just to start with you should be flashing ap. secondly that is a very old odin to even have that option so upgrade and thirdly if a device turns on it is not hard bricked. You misinstalled an os you need to wipe . If you didnt screw up your recovery partition try from there if you cant....idk im not going to explain adb because its a lengthy explanation and you would have had to have it enabled in dev options to work so i guess flash anyway. you must be using samsung stock firmware or odin wouldnt flash it needs to be bpa1 or cq....i cant remeber the last 2 idrntifiers but its 6.0.1 the very first marshmellow . You cant get below 5.1.1. Its savable just relax and start over .
mojoswagger1980 said:
You shouldnt be flashing pda bro , just to start with you should be flashing ap. secondly that is a very old odin to even have that option so upgrade and thirdly if a device turns on it is not hard bricked. You misinstalled an os you need to wipe . If you didnt screw up your recovery partition try from there if you cant....idk im not going to explain adb because its a lengthy explanation and you would have had to have it enabled in dev options to work so i guess flash anyway. you must be using samsung stock firmware or odin wouldnt flash it needs to be bpa1 or cq....i cant remeber the last 2 idrntifiers but its 6.0.1 the very first marshmellow . You cant get below 5.1.1. Its savable just relax and start over .[/QUOT
sorry i mean AP not PDA, iam using last odin version,i have downloaded last 6.0.1 firmware from sammobile,and i tryed to flash on AP,fail and fail again, odin says no pit partition file,even i find pit file and tick repartition and it still saying same error,thanks for answering
Click to expand...
Click to collapse
alfrecuba said:
my note 4 sm-n910v does not do anything,only when i conect it to the computer shows up QHS_BULK.
I already tried unbrick image and now i can but into download mode but when i try to flash with PDA and PIT i got e_mmc write filed.
What can i do?
Click to expand...
Click to collapse
It sounds like your eMMC is failing
ryanbg said:
It sounds like your eMMC is failing
Click to expand...
Click to collapse
Or DM verity got tripped .
---------- Post added at 10:04 AM ---------- Previous post was at 10:01 AM ----------
alfrecuba said:
mojoswagger1980 said:
You shouldnt be flashing pda bro , just to start with you should be flashing ap. secondly that is a very old odin to even have that option so upgrade and thirdly if a device turns on it is not hard bricked. You misinstalled an os you need to wipe . If you didnt screw up your recovery partition try from there if you cant....idk im not going to explain adb because its a lengthy explanation and you would have had to have it enabled in dev options to work so i guess flash anyway. you must be using samsung stock firmware or odin wouldnt flash it needs to be bpa1 or cq....i cant remeber the last 2 idrntifiers but its 6.0.1 the very first marshmellow . You cant get below 5.1.1. Its savable just relax and start over .[/QUOT
sorry i mean AP not PDA, iam using last odin version,i have downloaded last 6.0.1 firmware from sammobile,and i tryed to flash on AP,fail and fail again, odin says no pit partition file,even i find pit file and tick repartition and it still saying same error,thanks for answering
Click to expand...
Click to collapse
Sorry bud i can't say I've ever heard of what your describing, (your phone shows up as q_bulk ) try flashing 5.1.1 bpa1 and see if it will take ... Hopefully it isn't a bad emmc chip
Click to expand...
Click to collapse

Categories

Resources