Develop Bugs

[Solved] Request for root, unlock , cwm recovery for Lenovo Ideaphone A390

I own a Lenovo Ideaphone A390 and have noticed that root, unlock,cwm has not been released for this phone yet. It is an amazing phone and would like it very much if someone could plzz help me root my phone.
I would appreciate all and any help.
Thnx in advanced

DarthRecca said:
I own a Lenovo Ideaphone A390 and have noticed that root, unlock,cwm has not been released for this phone yet. It is an amazing phone and would like it very much if someone could plzz help me root my phone.
I would appreciate all and any help.
Thnx in advanced
Click to expand...
Click to collapse
Hi.. Did you try unlockroot.com???? Or SRSRoot??? Try it

mohamadraisbinrahim said:
Hi.. Did you try unlockroot.com???? Or SRSRoot??? Try it
Click to expand...
Click to collapse
Incompatible with Unlock root
Same with SRSRoot
Please suggest something else

Lenovo A390 Rooted
DarthRecca said:
I own a Lenovo Ideaphone A390 and have noticed that root, unlock,cwm has not been released for this phone yet. It is an amazing phone and would like it very much if someone could plzz help me root my phone.
I would appreciate all and any help.
Thnx in advanced
Click to expand...
Click to collapse
I found instructions to root the A390 here.
Step 1: Download and unzip the three attached files.
Step 2: To install the drivers for the computer, had to reboot the computer (Win8 64x) and disable driver signing. Then turn off the phone, connect to the computer, and run the InstallDriver.exe. After the driver installation is complete, disconnect the phone. The phone only makes the pre-loader interface available for a couple seconds when the USB cable is first plugged into the computer.
Step 3: Open the folder with the flash tool, and run Flash_tool.exe. Click the scatter-loading button and select "MT6577_Android_scatter_emmc.txt" from the recovery folder you downloaded. The recovery check box should automatically be populated with the TWRP.img file.
Step 4: Click download button and select "yes" to ignore the dialogue box. The flash software will now wait till it sees the MT6577 interface from the phone. With the phone off. Plug the USB cable into the phone and then into the computer. The flashing software will automatically load the recovery image to the phone. The flash-tool will show the power status bar red to yellow then wait for the message "OK" green is successful, then disconnect the phone, the TWRP recovery has been flashed. If the flash does not detect the phone when you plug it in, check your driver installation from step 2.
Step 5: Access recovery mode by pressing volume up + home + power key until the phone vibrates or it boots into recovery mode, then let go. This time open Team Win Recovery. You now have TW recovery and you can now root your device. (Make android backup first before rooting you phone)
Rooting Lenovo Ideaphone A390
After boot in recovery it will ask you to install superSU just drag/swipe to install. After you reboot the phone, you will have to have internet access to download the GUI. You can download the GUI from the play store, or download a zip which you can flash from recovery.
You are now rooted!
Good Luck
I also found a video walk through here.

thnx

srs root is working
DarthRecca said:
Incompatible with Unlock root
Same with SRSRoot
Please suggest something else
Click to expand...
Click to collapse
srsroot is working with a390 , i've rooted many a390 with connected pc/notebook to internet when you start the programs,

Voice Calls
hello! Recently, I bought a Lenovo A390 and i think that it has a problem with the voice calls. During the voice call, the person who i´m talking doesn´t hear me no more and end the call. I think the phone have a problem with the sensor because the screen flash when i put it on the ear. Anyone knows what i´m talking about? Thanks!

Just can not send the recovery file to my Lenovo A390 using SP Flashtool
Hello,
I have installed the correct drivers because I did manage to flash my ZTE v889s phone and send a recovery.file to it.
But with my Lenovo A390 I have tried over a week and nothing will work. After SP Flashtool finds the phone, it gives an error message after 4 seconds, saying:
BROM_ERROR: S_FT_NEED_DOWNLOAD_ALL_FAIL (4050)
I am sure this must be some kind of locking mechanics on the phone, and not a problem with the drivers, since they are working with other Android devices. Do you know what could be the problem?
The phone is suposed to be rooted, I am using SuperSU, that I installed using the USB cable on the device.
All your good advice is highly appreciated!
Thanks!

warcious said:
Hello,
I have installed the correct drivers because I did manage to flash my ZTE v889s phone and send a recovery.file to it.
But with my Lenovo A390 I have tried over a week and nothing will work. After SP Flashtool finds the phone, it gives an error message after 4 seconds, saying:
BROM_ERROR: S_FT_NEED_DOWNLOAD_ALL_FAIL (4050)
I am sure this must be some kind of locking mechanics on the phone, and not a problem with the drivers, since they are working with other Android devices. Do you know what could be the problem?
The phone is suposed to be rooted, I am using SuperSU, that I installed using the USB cable on the device.
All your good advice is highly appreciated!
Thanks!
Click to expand...
Click to collapse
Hi everyone, i just bought an a390 and i'm using the same tools as described here. I cant' install the recovery because i'm having the same problem that warcious is having. Any ideas what's happening this and how to fix it? Thanks.

Lenovo A390T Rooting?
scoutdriver73 said:
I found instructions to root the A390
Step 1: Download and unzip the three attached files.
Step 2: To install the drivers for the computer, had to reboot the computer (Win8 64x) and disable driver signing. Then turn off the phone, connect to the computer, and run the InstallDriver.exe. After the driver installation is complete, disconnect the phone. The phone only makes the pre-loader interface available for a couple seconds when the USB cable is first plugged into the computer.
Step 3: Open the folder with the flash tool, and run Flash_tool.exe. Click the scatter-loading button and select "MT6577_Android_scatter_emmc.txt" from the recovery folder you downloaded. The recovery check box should automatically be populated with the TWRP.img file.
Step 4: Click download button and select "yes" to ignore the dialogue box. The flash software will now wait till it sees the MT6577 interface from the phone. With the phone off. Plug the USB cable into the phone and then into the computer. The flashing software will automatically load the recovery image to the phone. The flash-tool will show the power status bar red to yellow then wait for the message "OK" green is successful, then disconnect the phone, the TWRP recovery has been flashed. If the flash does not detect the phone when you plug it in, check your driver installation from step 2.
Step 5: Access recovery mode by pressing volume up + home + power key until the phone vibrates or it boots into recovery mode, then let go. This time open Team Win Recovery. You now have TW recovery and you can now root your device. (Make android backup first before rooting you phone)
Rooting Lenovo Ideaphone A390
After boot in recovery it will ask you to install superSU just drag/swipe to install. After you reboot the phone, you will have to have internet access to download the GUI. You can download the GUI from the play store, or download a zip which you can flash from recovery.
You are now rooted!
Good Luck
I also found a video walk through
Will this procedure work on the Lenovo A390T ?
Thank you
Click to expand...
Click to collapse

Root using Framaroot...after that install twrp...just search recovery.img using googles..
Sent from my Lenovo A390_ROW

Will this procedure work on the Lenovo A390T ?
Will this procedure work on the Lenovo A390T ?
Thank you

My Lenovo A390 has problems with its ANDROID CORE AND ALL THE ANDROID COMPONENTS!!!!
Hi all. I got a rooted Lenovo A390 and I downloaded ROM Toolbox LITE. I used build.prop editor. I accidentally edited the vm growth heapsize from 16 to 10. then after rebooting the phone, everything didn't work anymore. The android phone, android core, google services, gapps, and everything else stopped working and the notification bar dissapeared and nothing in the phone will open. Does somebody know how to reverse it without using the apps in the phone since nothing would open?

ultimate bootloop
i think i got a dead end, just trying (desperately) to fix my phone,
the situation is :
usb debugging is off
stucks at boot
the recover is not functional (just an android logo and red exclamation point
can't install the drivers
how can i fix this? or is it really dead?
thank to those who will help

TheMaskaras said:
scoutdriver73 said:
I found instructions to root the A390
Step 1: Download and unzip the three attached files.
Step 2: To install the drivers for the computer, had to reboot the computer (Win8 64x) and disable driver signing. Then turn off the phone, connect to the computer, and run the InstallDriver.exe. After the driver installation is complete, disconnect the phone. The phone only makes the pre-loader interface available for a couple seconds when the USB cable is first plugged into the computer.
Step 3: Open the folder with the flash tool, and run Flash_tool.exe. Click the scatter-loading button and select "MT6577_Android_scatter_emmc.txt" from the recovery folder you downloaded. The recovery check box should automatically be populated with the TWRP.img file.
Step 4: Click download button and select "yes" to ignore the dialogue box. The flash software will now wait till it sees the MT6577 interface from the phone. With the phone off. Plug the USB cable into the phone and then into the computer. The flashing software will automatically load the recovery image to the phone. The flash-tool will show the power status bar red to yellow then wait for the message "OK" green is successful, then disconnect the phone, the TWRP recovery has been flashed. If the flash does not detect the phone when you plug it in, check your driver installation from step 2.
Step 5: Access recovery mode by pressing volume up + home + power key until the phone vibrates or it boots into recovery mode, then let go. This time open Team Win Recovery. You now have TW recovery and you can now root your device. (Make android backup first before rooting you phone)
Rooting Lenovo Ideaphone A390
After boot in recovery it will ask you to install superSU just drag/swipe to install. After you reboot the phone, you will have to have internet access to download the GUI. You can download the GUI from the play store, or download a zip which you can flash from recovery.
You are now rooted!
Good Luck
I also found a video walk through
Will this procedure work on the Lenovo A390T ?
Thank you
Click to expand...
Click to collapse
Click to expand...
Click to collapse

i just wanted to clear everything off and back to stock. hopefully the stock recovery can do that?

no download mode

Hy guys i have a G E-975 with korean kit kat from leaked F180K unlocked with freegee and framaroot my phone works perfect boots to recovery normal open and close the same normal my problem is that it doesn't boot to download mode for no reason i installed all the drivers i read all the articles of xda tried many times unistall and reinstall try different computer exactly the same normal boot normal recovery no download mode......please help i want to downgrade to the official but if i can't i will stay to custom for ever.....

soniccm said:
Hy guys i have a G E-975 with korean kit kat from leaked F180K unlocked with freegee and framaroot my phone works perfect boots to recovery normal open and close the same normal my problem is that it doesn't boot to download mode for no reason i installed all the drivers i read all the articles of xda tried many times unistall and reinstall try different computer exactly the same normal boot normal recovery no download mode......please help i want to downgrade to the official but if i can't i will stay to custom for ever.....
Click to expand...
Click to collapse
Stupid question, but are you sure you are doing it right? To enter download mode, first turn the phone off. Then hold both volume buttons, and plug in the USB cable to your computer. Do NOT press the power button. Is this what you are doing?
Also, are you saying you rooted an F180 KitKat with Framaroot?!?! I find that very hard to believe, as it failed for me, and other people also confirmed that it didn't work...

kt-Froggy said:
Stupid question, but are you sure you are doing it right? To enter download mode, first turn the phone off. Then hold both volume buttons, and plug in the USB cable to your computer. Do NOT press the power button. Is this what you are doing?
Also, are you saying you rooted an F180 KitKat with Framaroot?!?! I find that very hard to believe, as it failed for me, and other people also confirmed that it didn't work...
Click to expand...
Click to collapse
sorry dude if i was sure that i made ir right that would be a problem... I have try both with power and volumes +,- and without power deeply black screen nothing more less. My lg is not an F180 is an E975 rooted and cwm recovery with leaked kit kat from the korean F180 i wrote it in first post

Anybody knows how to boot my E 975 into download mode????
any solution i tried from internet didn't work...please help
today tried and hard reset it nothing happens only 2 sort vibrates and nothing more is a protection of the phone or i bricked it any help???
anybody????

The same thing happened to me .. The phone didn't show DOWNLOAD MODE. ... i still flashed the stock kdz by these steps
1.. switch off ur phone
2.. keep the up and down volume buttons pressed and insert the usb cable
3.. open Kdz updater ..
4 .. click read phone information. .and wait for a minute
5.. if it even shows a slight progress seen in the green bar , then you have a go..
Notes
:1.. if the kdz updater even hangs and stops responding while reading ur phone info.. and takes some time.. ur phone is connected in download mode even it shows the slightest progress in the progress bar ( green coloured)
2... if u cant switch off ur phone due to frequent restarts. . just keep the cable connected and the volume buttons pressed while it is restarting
[you can also see ur computer's device mgr for ur phone connection ]
then just flash the Kdz as you do..
I HAVE DONE IT MYSELF several times when my phone didn't show Download mode on the screen.. but cannot guarantee it'll work for you too.. I I'd recommend you to give it a try as it always worked fir me..
BEST IF LUCK

MasterFURQAN said:
The same thing happened to me .. The phone didn't show DOWNLOAD MODE. ... i still flashed the stock kdz by these steps
1.. switch off ur phone
2.. keep the up and down volume buttons pressed and insert the usb cable
3.. open Kdz updater ..
4 .. click read phone information. .and wait for a minute
5.. if it even shows a slight progress seen in the green bar , then you have a go..
Notes
:1.. if the kdz updater even hangs and stops responding while reading ur phone info.. and takes some time.. ur phone is connected in download mode even it shows the slightest progress in the progress bar ( green coloured)
2... if u cant switch off ur phone due to frequent restarts. . just keep the cable connected and the volume buttons pressed while it is restarting
[you can also see ur computer's device mgr for ur phone connection ]
then just flash the Kdz as you do..
I HAVE DONE IT MYSELF several times when my phone didn't show Download mode on the screen.. but cannot guarantee it'll work for you too.. I I'd recommend you to give it a try as it always worked fir me..
BEST IF LUCK
Click to expand...
Click to collapse
please tell me how u flash kdz my which method on which operating system bcoz ican enter into download mode but never got success in flashing kdz please elaborate whole procedure for me i am from india

I already elaborated. . jjust. follow the steps.. i also have the e975 indian..
just reply if you have problems with any steps
---------- Post added at 08:14 AM ---------- Previous post was at 08:10 AM ----------
worldone98 said:
please tell me how u flash kdz my which method on which operating system bcoz ican enter into download mode but never got success in flashing kdz please elaborate whole procedure for me i am from india
Click to expand...
Click to collapse
i have flashed it on Win 7 x86 and win 8.1 pro x64
---------- Post added at 08:19 AM ---------- Previous post was at 08:14 AM ----------
worldone98 said:
please tell me how u flash kdz my which method on which operating system bcoz ican enter into download mode but never got success in flashing kdz please elaborate whole procedure for me i am from india
Click to expand...
Click to collapse
follow these steps.. :if you have less than 1 gb kdz file
1) Download the latest KDZ from LG's server for your phone via
the app below (kudos to the creator)
http://www.mediafire.com/?cgeb6o5osy2yl9c
2) Make sure you have LG United Drivers already installed,
otherwise download from below
http://www.mediafire.com/?82nt1aeh04aqa3m
3) Download LG KDZ Updater
http://www.mediafire.com/?sj5y073xal03ntw
4) Download the manual adb wipe batch file
http://www.mediafire.com/?ru7erfxsz7p7s3p
5) Put your Optimus G into Download Mode by switching it off,
attaching the usb cable to the phone, holding both the up and
down volume buttons at the same time and lastly inserting the
usb cable into the computer; wait for the drivers to finish
loading if doing it for the first time.
6) Unzip the downloaded updater zip file and run KDZ_FW_
UPD.exe. Use the settings below
Type: 3GQCT
Phone Mode: CS_Emergency
KDZ file: navigate to the folder which you have saved the
downloaded KDZ from the step (1)
Click Launch Software Update and wait for the flash process to
finish
7) Your phone will restart itself when IParam = 90 is displayed
and proceed slower until you see IParam=1 again (which
signals the end of flash, you can safely exit the program then
and remove the cable from the phone). If phone boots up
normally, congrats, skip the steps below and proceed to use the
phone as per normal.
However, this most probably will not be the case for newer
Optimus-es, as the data partition somehow wasn't wiped even
when KDZ-ed, remaining 'dirty', thus causing bootloop or
security infringement.
8) If the phone is stuck at the booting up LG/Telco logo, you
will need to manually wipe the data partition.
9) Force the phone off by holding the power button for appx
15secs.
10) Put the phone into recovery mode by holding the volume up
and home button concurrently, then press the power button. Let
go of all the buttons after you see the LG logo on screen for the
2nd time and the screen goes blank thereafter (backlight may
still be on). The phone will kind of reboot and then enters
recovery mode. Repeat the process if you did not get it the first
time.
11) With the phone in Recovery Mode, connect it to the
computer, wait for the drivers to load (if doing it for the first
time), unzip the wipe batch file downloaded earlier from step (4)
, double click on wipe.bat to execute the wipe command.
12) Your phone will auto reboot when wiped and (hopefully)
boot as per normal.
Hope with this simple guide fellow members will feel safer when
rooting or removing non essential LG wares from their Optimus
---------- Post added at 08:24 AM ---------- Previous post was at 08:19 AM ----------
worldone98 said:
please tell me how u flash kdz my which method on which operating system bcoz ican enter into download mode but never got success in flashing kdz please elaborate whole procedure for me i am from india
Click to expand...
Click to collapse
if you have greater thsn 1 gb kdz file
REQUIREMENTS:
MUST HAVE LG DRIVERS
MSXML
.NET FRAMEWORK INSTALLED
1.DOWNLOAD THE ROM/KDZ
2.DOWNLOAD LATEST LG MOBILE SUPPORT TOOL
http://csmg.lgmobile.com:9002/client...2CAppSetup.exe
INSTALL IT WHEN DONE. CLOSE AND END PROCESS ON
TASKMANGER.
3.DOWNLOAD LG R&D TOOL
http://storagecow.eu/index.php?dir=X.../Programs/
4.GO TO DOWNLOAD MODE POW+BOTH VOL BUTTON
PRESSED+CONNECT USB
6) Extract FlashTool and run UpTestEX.exe
7) In R&D Test Tool window,
Select Type = 3GQCT (top left hand side)
PhoneMode = DIAG (top right hand side)
Select kdz file = click to select your LG stock rom *.kdz
Click "Normal web upgrade test" (bottom right hand side)
Then another window will pop up, click "Upgrade Start" button
wait a few seconds, another window "Select Country &
Language" pop up,
=> Country=Republic of Korea
=> Language=English
you can click ok to proceed
8) All Done and wait for finish!
---------- Post added at 08:34 AM ---------- Previous post was at 08:24 AM ----------
worldone98 said:
please tell me how u flash kdz my which method on which operating system bcoz ican enter into download mode but never got success in flashing kdz please elaborate whole procedure for me i am from india
Click to expand...
Click to collapse
IMPIRTANT NOTE: DO NOT USE USB 3.0 PORT FOR THIS.. use only usb 2.0 port with a good usb cable as provided with the phone

when i hit update button the app crash for both solutions....
I don't understand my phone works fine but i can't boot to download mode or recovery from the start (with button press) i can boot recovery only with rom manager please somebody which is the combinations for LG E975 for download mode and for recovery because i mess my mind with all this models?????

flash other bootloader in recovery! (z30d mako bootloader but look at updater script and when needed, delete first lines with device info ****...)

2nd Sky said:
flash other bootloader in recovery! (z30d mako bootloader but look at updater script and when needed, delete first lines with device info ****...)
Click to expand...
Click to collapse
hey budy i'm a noob i don't understand what should be needed to delete and replace with what and where is this script make it clearer if that is possible (i don't want to brick my G just want to go back to stock)
ps. so easy to go to custom so hard to go back to stock

[Q] [URgENT] Need Help for A Hard Bricked Device

I have a hard bricked xolo q1000 with me. Installed some drivers (hopefully these are the correct drivers)
Phone is detected in SP and on PC as MTK USB COM.. (COM32) so atleast that part is good
I also downloaded the stock ROMs
I DONT HAVE MTKDROID backup.
i am getting a 5069 No Space error \ -_- / so i am unable to flash either of the stock roms (from needrom)
->> can someone please upload PMT file and SCATTER FILE here.. i even tried creating my own scatter file but everything leads to the SAME ERROR.. 5069.. Tried ALL VERSIONS OF SP F T (Attached Screenshot)
i am 90% sure that the emmc is not physically damaged..
If someone could give me the link to the PROPER PRELOADER too.. that would be nice
->> i also have ADB, havent tried using that here..
->> Also need some instructions for flashing and removing 5069 error so phone can boot up..

Hello TC... before your Phone Is HArd Brick Which Rom You Are Using???

Same problem in my xolo q1000 mobile
I have rooted my xolo q1000 phone by kingsoroot software from my PC. After that I have uploaded the image file from the falshify app from the play store. On rebooting it got hard-bricked. I tried to go to recovery mode by pressing volume up key and power button but not able to go to recovery mode.
as it has changed my setting. by pressing camera + power button I am able to get into the recovery mode. i can choose the items by camera button, but not able to do the OK on any of the option.
Please help.
Its not even getting detected by device manager in the PC as it keep refreshing it several times at a gap 1 second.
Thanks in advance.

How to "debrick/unbrick"an oppo find 7/7a

Greetings,im Akmal and today I will be sharing some helpful solution to unbrick your Oppo Find 7/7A.​Short Story(myb a lil bit longer)¬
So my find 7A got soft bricked when I install custom rom without using TWRP(pretty stupid to do so)
After rebooting my phone keeps on booting to fastboot mode and no matter it happen the same if i press vol up/vol down and power button.
At this stage I knew my phone is soft bricked.So I found the solution to it through some old posts which you have to extract the ColorOS blablabla and adb thingy(I dont wanna go through it here)
But I dont realised that i forget to flash a file name "TZ.MBN"
Now that my phone wont ever boot or even to fastboot which resulted to hard brick.
No recovery screen.
No Charging status screen
No Fastboot screen
No sign of vibrating when i push the power button
-So here is the solution-
Disclaimer-I am not responsible for what ever happen to your device after this-
-there are already some other posts like this but I make this post to let you know that its still working.
1a)First,download the OPPO UNBRICK TOOL HERE
bit.ly/OPPOUNBRICK
1b)goto Google and search for Qualcomm qd loader.download,install and restart your pc.
2)After restarting,Extract the file from OPPO UNBRICK TOOL and open "Msm8974DownloadTool.exe"
3)as you may have notice,its chinese language or some aliens language but dont worry it isn't corrupted,just follow through↓
4)disconnect your device battery,then open the software and press start,after that connect the phone to your pc/laptop (WITHOUT BATTERY) and hold volume up button
5)please wait patiently as it is reflashing stock rom to your device.
6)as you may have noticed maybe your device disconnected but DONT GET PANICKED! press again the power button until its downloading again on the software.
7)If it has done downloading,some row should be in a Green colour.
8)disconnect your cable and try turning on your device again.
That's it!Any comment or curiosity I will try helping you through the comment section but I not guaranteed everything I can answer
P/S:if your device is softbricked,you just should disconnect your battery,and then open the software and press start,then connect the phone to your pc/laptop (WITHOUT BATTERY) and hold volume up button.
If your device is hard bricked(like mine)only holding the power button could work as well
*UPDATE* 24/2/2019
-If you guys still have any concerns kindly contact me through twitter (0728mal)
*UPDATE* 4/7/2020
-yes it is still working guys,no worries kayy
-no you don't need internet for it to work,the software already has all the files needed to flash the device,which is why the file is pretty big.
best regards,
Akmal

Link updated :good:

akmlfhm said:
Greetings,im Akmal and today I will be sharing some helpful solution to unbrick your Oppo Find 7/7A.​Short Story(myb a lil bit longer)¬
So my find 7A got soft bricked when I install custom rom without using TWRP(pretty stupid to do so)
After rebooting my phone keeps on booting to fastboot mode and no matter it happen the same if i press vol up/vol down and power button.
At this stage I knew my phone is soft bricked.So I found the solution to it through some old posts which you have to extract the ColorOS blablabla and adb thingy(I dont wanna go through it here)
But I dont realised that i forget to flash a file name "TZ.MBN"
Now that my phone wont ever boot or even to fastboot which resulted to hard brick.
No recovery screen.
No Charging status screen
No Fastboot screen
No sign of vibrating when i push the power button
-So here is the solution which make my phone came to life again-
Disclaimer-I am not responsible for what ever happen to your device after this-
-there are already some other posts like this but I make this post to let you know that its still working.
-make sure to charge the phone first even if you do not know if it charging or not
1)First,download the OPPO UNBRICK TOOL HERE
bit.ly/OPPOUNBRICK
2)Extract the file and open "Msm8974DownloadTool.exe"
3)as you may have notice,its chinese language or some aliens language but dont worry its not corrupted,just follow through
4)Connect your phone to PC and press the power button until you heard some like mounted usb alert on windows.(its ok aslong windows does not detect it on device manager but its ok if you can hear the alert sound.
5)back to the software,no need to mess around with it.Click on start until its downloading a "new life" to your phone.
6)as you may have noticed maybe your device disconnected but DONT GET PANICKED! press again the power button until its downloading again on the software.
7)If it has done downloading,some row should be in a Green colour.
8)disconnect your cable and try to turning on your device again.
That's it!Any comment or curiosity I will try helping you through the comment section but I not guaranteed everything I can answer
best regards,
Akmal
Click to expand...
Click to collapse
hi im having this problem as well. my find 7a is hard bricked after i flash coloros v2.1.5i without twrp. the problem is, my computer does not detect my phone at all even after i hard reset and hold power button for 30 seconds. i dont think the battery is drained because before this happened, my phones battery was about 90% and i try recharging the phone for 30 minutes, and nothing happened. so the debrick tool cannot be used. can you suggest anything for my problem?

Got excited when I read this post! Is there an Oppo Unbrick tool for Mac? I don't have a Windows machine so I can't run the .exe file... Is there an equivalent for those of us not on Windows? Thank you

Shadician said:
Got excited when I read this post! Is there an Oppo Unbrick tool for Mac? I don't have a Windows machine so I can't run the .exe file... Is there an equivalent for those of us not on Windows? Thank you
Click to expand...
Click to collapse
On Mac's OS, you can always install Windows on its proprietary virtual machine and get the process going that way.

babyenchantress said:
hi im having this problem as well. my find 7a is hard bricked after i flash coloros v2.1.5i without twrp. the problem is, my computer does not detect my phone at all even after i hard reset and hold power button for 30 seconds. i dont think the battery is drained because before this happened, my phones battery was about 90% and i try recharging the phone for 30 minutes, and nothing happened. so the debrick tool cannot be used. can you suggest anything for my problem?
Click to expand...
Click to collapse
hello there!I'm really sorry for not checking this that often and really sorry if i let you down because im too busy with my schools work
btw before my computer can detect my phone i have to download a driver which detect qualcomm processor for my oppo then it can be detected by my pc therefore i can do the unbrick process:good:

Shadician said:
Got excited when I read this post! Is there an Oppo Unbrick tool for Mac? I don't have a Windows machine so I can't run the .exe file... Is there an equivalent for those of us not on Windows? Thank you
Click to expand...
Click to collapse
yeah you can try WINE also but i never have any experience with mac os before so i cant guarantee that it will work considering that you're configuring your drivers,which can go wrong if not done correctly

So I have bricked my phone (X9006) while trying to install TWRP recovery. It is stuck on logo and adb/ fastboot does not recognise it anymore. I have tried the above-mentioned tool, but this program also does not do anything for a long time. Am I missing something in applying this solution?
Edit: I am an Windows 10 and I might not have the Qualcomm drivers installed. I don't know how to install

true_friend2004 said:
So I have bricked my phone (X9006) while trying to install TWRP recovery. It is stuck on logo and adb/ fastboot does not recognise it anymore. I have tried the above-mentioned tool, but this program also does not do anything for a long time. Am I missing something in applying this solution?
Edit: I am an Windows 10 and I might not have the Qualcomm drivers installed. I don't know how to install
Click to expand...
Click to collapse
Hello there.have you tried downloading the "Qualcomm"
Driver software on your PC?

is it necessary to remove the battery? I don't have tools for opening my phone and it's battery is non-removable

Perhaps an important step is missing. The Qualcomm qd loader driver is may not signed. I had to boot into the extended start menu on Windows 10 and disable the driver signature check - point 7 - and could now successfully debrick my find7.

Vibe P1A42 stuck at Lenovo logo bootloop

Hello Guys,
My Lenovo P1A42 is stuck in Lenovo logo bootloop.
I tried to flash the stock rom "P1a42_S288_160721_ROW_RAW_QFIL" with QFIL.
So with QFIL, I see the Qualcomm HS-USB QDLoader 9008 (COM3).
I select "P1a42_S288_160721_ROW_RAW_QFIL\prog_emmc_firehose_8936.mbn" for programmer path.
I select build "P1a42_S288_160721_ROW_RAW_QFIL"
I also select rawprogram0.xml and patch0.xml.
It takes about 10 minutes to download and in the end "Download succeed. Finish download" message appears.
After this step, I press power+vol up+vol down together for around 12 secs to let the phone start with the downloaded new rom but again the phone goes to lenovo logo bootloop.
I have been continuosly searching for the solution but I still could not find it.
Probably I am missing a very small detail.
Can somebody please help me with this problem?
Thanks in advance.
Regards.

After a lot of trials I could solve the problem, but I dont know what I did different.
I did everything the same.
Anyway thanks to everybody who read.
Regards.

hagiwatt said:
Hello Guys,
My Lenovo P1A42 is stuck in Lenovo logo bootloop.
I tried to flash the stock rom "P1a42_S288_160721_ROW_RAW_QFIL" with QFIL.
So with QFIL, I see the Qualcomm HS-USB QDLoader 9008 (COM3).
I select "P1a42_S288_160721_ROW_RAW_QFIL\prog_emmc_firehose_8936.mbn" for programmer path.
I select build "P1a42_S288_160721_ROW_RAW_QFIL"
I also select rawprogram0.xml and patch0.xml.
It takes about 10 minutes to download and in the end "Download succeed. Finish download" message appears.
After this step, I press power+vol up+vol down together for around 12 secs to let the phone start with the downloaded new rom but again the phone goes to lenovo logo bootloop.
I have been continuosly searching for the solution but I still could not find it.
Probably I am missing a very small detail.
Can somebody please help me with this problem?
Thanks in advance.
Regards.
Click to expand...
Click to collapse
Please follow Getting Ready and Flashing ROM from the link https://forum.xda-developers.com/vibe-p1/development/qpst-flashing-vibeui-3-1-s272-rom-t3386650 . Once Success, The system/Phone reboots itself, You need not hold any combination of keys to reboot
Primarily make sure Your PC?Laptop detects QComm Driver when you Hold Vol Up+USB. If the device is detected and Driver not installed, You can install the same from the above link.
Verify the above using Device manager.

pavanpilot94 said:
Please follow Getting Ready and Flashing ROM from the link https://forum.xda-developers.com/vibe-p1/development/qpst-flashing-vibeui-3-1-s272-rom-t3386650 . Once Success, The system/Phone reboots itself, You need not hold any combination of keys to reboot
Primarily make sure Your PC?Laptop detects QComm Driver when you Hold Vol Up+USB. If the device is detected and Driver not installed, You can install the same from the above link.
Verify the above using Device manager.
Click to expand...
Click to collapse
Dear pavanpilot94,
Thank you for your message.
I had already made the procedure following the instructions in the link you sent to me. In the end of the download "Download succeed. Finish download" message appeared, but it did not restart automatically.
That is why as mentioned in the instructions you sent; ("If "ready" message appears and device does not go to reboot, then hold Volume UP + Power buttons for ~12 sec.")), I had to make the key combination.
But everytime the device went to reboot the old Android in the device, so flashing was not successful.
I do not know where the problem was. After many trials, I could flash successfully, but everytime I had to do the same things. I did not make anything different.
Anyway the problem is solved now, but next time flashing, I do not know how to avoid this problem.
Thank you very much.

hagiwatt said:
Dear pavanpilot94,
Thank you for your message.
I had already made the procedure following the instructions in the link you sent to me. In the end of the download "Download succeed. Finish download" message appeared, but it did not restart automatically.
That is why as mentioned in the instructions you sent; ("If "ready" message appears and device does not go to reboot, then hold Volume UP + Power buttons for ~12 sec.")), I had to make the key combination.
But everytime the device went to reboot the old Android in the device, so flashing was not successful.
I do not know where the problem was. After many trials, I could flash successfully, but everytime I had to do the same things. I did not make anything different.
Anyway the problem is solved now, but next time flashing, I do not know how to avoid this problem.
Thank you very much.
Click to expand...
Click to collapse
I now understand very clearly hagiwatt,
I'm happy that Device is back!!! :good::good::highfive:
On a Guess from the above understood there might be corrupt emmc locations, For this to be verified we might have to format the entire emmc. I'm too stuck with Logo Screen now, Unfortunately my Device is not getting detected by the Computer(Qcomm QDLoader) to have it flashed.
Trying to Fix it, I did a entire Format & Verified any Bad sectors as suggested by one of the developer, Unfortunately still not able to get the device detected.

pavanpilot94 said:
I now understand very clearly hagiwatt,
I'm happy that Device is back!!! :good::good::highfive:
On a Guess from the above understood there might be corrupt emmc locations, For this to be verified we might have to format the entire emmc. I'm too stuck with Logo Screen now, Unfortunately my Device is not getting detected by the Computer(Qcomm QDLoader) to have it flashed.
Trying to Fix it, I did a entire Format & Verified any Bad sectors as suggested by one of the developer, Unfortunately still not able to get the device detected.
Click to expand...
Click to collapse
I struggled for it since I wanted to send the device to warranity for vibration problem. I am happy that I could flash with the raw rom. I also wanted to reset the binary counter but no way.
Triangle Away does not support Lenovo.
I hope they are not checking the binary counter in the service center.
Does anyone have an experience about it?
Thanks.

hagiwatt said:
I struggled for it since I wanted to send the device to warranity for vibration problem. I am happy that I could flash with the raw rom. I also wanted to reset the binary counter but no way.
Triangle Away does not support Lenovo.
I hope they are not checking the binary counter in the service center.
Does anyone have an experience about it?
Thanks.
Click to expand...
Click to collapse
Hi Everybody!
I have just recieved the phone from service center. They fixed the vibration problem under warranity.
So binary counter did not affect the warranity status.
I dont know if they checked the counter or not.
For information to anyone who has the same issue.
Regards.

pavanpilot94 said:
Please follow Getting Ready and Flashing ROM from the link https://forum.xda-developers.com/vibe-p1/development/qpst-flashing-vibeui-3-1-s272-rom-t3386650 . Once Success, The system/Phone reboots itself, You need not hold any combination of keys to reboot
Primarily make sure Your PC?Laptop detects QComm Driver when you Hold Vol Up+USB. If the device is detected and Driver not installed, You can install the same from the above link.
Verify the above using Device manager.
Click to expand...
Click to collapse
and if the pc did not detecte the phone and i cant see any thing new in device manager ,plz help me