hey guys finally managed to unbrick my xolo q1010i.. did tried a lot to get it back..
in case you get locked at abd sideload <filename>"...
just press power button + volume dowm button for 10sec
phone will restart...
FIRSTLY DON't EVER... AND NEVER EVER INSTALL "CHAINFIRE 3D" ON ANY XOLO WITH MEDIATEK PROCESSORS!!!!
its because chainfire is specially made for ARM devices and not for our MEDIATEK neon processors..
so before we start we need these tools and files...
SP TOOLS
Stock Q1010i 4.4.2 S002https://www.dropbox.com/s/1ih3a4nnma9g3mo/Stock q1010i 4.4.2 S002.7z?dl=0
DRIVERS
Driver_Auto_Installer_v1.1236.00.7z
this thread is for both hardbrick and softbrick.
there are two possibilites you might have caught up with..
Stuck at XOLO logo...
Not booting up...
so in either case follow this steps..
unfortunately i got caught in both...
so lets begin...
Phase 1: Installing drivers..
no matter if you have already installed the drivers... please make sure you install these again..
unzip the file " Driver_Auto_Installer_v1.1236.00.7z" from link.
run install.bat a command screen will popup saying install sp unsigned inf..
and pop up will come warning to ask you to install the driver or not simply install it.. the warning comes coz its just unsigned drivers not a big deal..
so the pop up will come like 2 or 4 times i actually didnt counted and it will take around 3 to 5 min to install it.. after installation of drivers the command screen will say
install complete press any key to continue... :good:
Phase 2: Installing SPtools, setting up ROM
so download the SPtools ROM from link
extract SPTOOLS in some folder say folder1;
and extract ROM in folder say folder2;
then
start flash_tool.exe
select scatter file from folder where ROM is ectracted.. (folder2)
all the files will be then automatically loaded
just make sure that phone is turned off in any case..
download button... and connect the phone
there will be loading of files and then green circle window will open..
disconnect the phone then you're done and phone is back from dead... :laugh: :angel: :highfive:
PRESS THAnKS OR PAYPAL ME IF I'D HELPED YOU...
I haven't been in such a condition but still thanks for informing..
Sent from my Q1010i using Tapatalk
My phone is not booting, even after installing drivers provided here.
It is now saying Device not recognized whenever i connect my phone. I have also tried other jacks, uninstalled and re-installed the drivers but nothing.
I think it is hard brick!!
Help please!!!
hey man, I have got my Xolo q1010i bricked and have come here to you for a solution. But I have one thing to ask you that, my phone has built-in battery and in the phase 2, you ask me to keep my phone off when I connect it to my PC. But it is out of my control and when I connect it to my PC through USB, it turns on to the xolo logo. What is a possible solution? Do I have to remove the battery socket to keep it off?
It is possible for me. Tell me if it is to be done.
.
[Reply by self]
Dude, solved the issue. Actually there were no issue as when I connect the phone to my PC when the "Download" button is already pressed in the SP Tool app, it automatically prevents the phone from booting up and solves the problem. If the phone is connected properly and the driver is installed OK, then there is actually no possibility for an error to occur.
Thanks dude, You saved my phone.
xolo q1010i hang on XOLO logo
Hello, I clear eMMC of my mobile. After that it hangs on XOLO logo. I tried to install ROM using SP tool. The process complete and it shows "Download OK" at the end but still when i start after process it hangs on XOLO logo. I tried to download different ROM but the situation remains same.
Am I missing some process that is needed after clear eMMC?
hello geeks,
I really need serious help. First the setup I have is as follows
1. I have LG G3 D855 but its european or Hong Kong or Taiwan version I don't know. I bought it in India. I updated it to android 5.0 Lollipop. Everything is fine till now.
2. Then I rooted my phone. This step was also fine. No problem.
3. Then I tried to download camera mod v2.0 to get some extra camera features like 60fps. In this step I got problems. I downloaded the media_profile.xml and copied it to /system/etc. But I made a mistake that I did not change its permission and rebooted the phone.
I am troubleshooting from a windows 8.1 PC. I downloaded the LG USB driver.
Due to this my phone stop at initial LG,Life is Good Screen. I tried different methods in internet.
1. I tired to access the device file file through adb. But the adb does not list the device.
2. I tried to use fastboot mode, but still fastboot does not list device when in the boot screen.
3. I pressed down pwr + volume down button and release after screen come up and then press again. I was asked to erase user data. I said yes and it erased the data. But still the same symptom when I reboot. Stuck at initial screen.
4. I tried to use LG PC Suite. But it does not even detect phone through the USB and there is no repair button.
5. I tried to enter downloading mode. This one is strange. I pressed down the vol up and then connected USB. But sometimes only it enters downloading mode and sometimes not. May be once in 10 times it enters downloading mode and 9 times it goes to initial boot LG screen.
I am not sure whats going on. Can anybody help me to figure it out ? Please help.
Thats because your not doing it properly
Research a guide on how to enter download mode and after that you can use flashtool to wipe your system and reinstall the original lg firmware
I have a canvas a1 AQ4501. Some days ago it just stopped working normally. When it turns on, I see the company logo with half screen turned yellow. Then it tries to restart but the same problem.
I have tried:
Using SP flash tools version 5.1524 but it goes into 2020 error while flashing, without battery. With battery phone is not detected.
Using twrp recovery to install cyanogenmod but it says partition had unexpected data after OTA update, something of this kind (did this using adb sideload)
The only thing that I can do with the phone is go into fastboot mode, recovery mode gets stuck on company logo. I can go to twrp recovery mode successfully.
I am using a windows 10 computer. Phone was on marshmallow when it last worked. I do not have an SD card. I have tried pressing both volume up and down with and without power button to flash using sp tool but phone is not detected bu sp flash tool in this case. I have tired meta mode (pressing volume up and power) here, phone is detected by sp flash tool but it goes into 2020 error BROM ERROR : S_BROM_CHKSUM16_MEM_RESULT_DIFF (2020).
Please help me as this phone is dear to me and has sentimental value.
Thanks for your time.
Bro give ur phone to MMX service center they will solve ur problem
I have a phone Lenovo Vibe shot z90a40 . Few days ago I have successfully flashed firmware with root facilities with Miflash . Phone was working fine . Then I tried to flash again another firmware with QFIL . I marked the options "Reset after Download" . After downloding the new ROM my vibe shot never start , it always stuck on Lenovo logo/text .
The problem are below -
1. When I press/hold Volume + button and plug in usb cable , the phone vibarte 2 times . So Miflash/QFIL could not detect com port .
2. I could not enable usb debugging mode because my phone never startup after last flashing , so ' adb reboot edl' command not working . device not found .
3. Also I can't enter any Mode , so I could not reset data , could not update from any update.zip from recovery .
4. If I press and hold volume + , volume - and power button at same time , PC detect comport as 9006 , its shows not writable .
5. I tried eMMC downloader to switch to Download mode but failed . :crying:
Please help me . Thanks
zahidbd2 said:
I have a phone Lenovo Vibe shot z90a40 . Few days ago I have successfully flashed firmware with root facilities with Miflash . Phone was working fine . Then I tried to flash again another firmware with QFIL . I marked the options "Reset after Download" . After downloding the new ROM my vibe shot never start , it always stuck on Lenovo logo/text .
The problem are below -
1. When I press/hold Volume + button and plug in usb cable , the phone vibarte 2 times . So Miflash/QFIL could not detect com port .
2. I could not enable usb debugging mode because my phone never startup after last flashing , so ' adb reboot edl' command not working . device not found .
3. Also I can't enter any Mode , so I could not reset data , could not update from any update.zip from recovery .
4. If I press and hold volume + , volume - and power button at same time , PC detect comport as 9006 , its shows not writable .
5. I tried eMMC downloader to switch to Download mode but failed . :crying:
Please help me . Thanks
Click to expand...
Click to collapse
Hello, it seems I really am facing the same problem here.
I tried all those steps above, and then I even tried to wipe and formal users data, even factory reset, but then, when I boot the phone, it is stuck on the booting screen saying Initializing. I wish I could give you all screenshot for this.
So, would anyone help us?
Hello
I m facing the same problem... initializing. http://forum.xda-developers.com/android/help/lenovo-vibe-z90-7-brick-stucking-t3328123
3 night that I m investigating this... No luck...
Hello! This happened to me just yesterday and I managed to solve it by following these steps:
- Download an official rom update (in a QSB file) - try googling Lenovo Z90-7 Vibe Shot - QSB.
- Create sdfuse folder on the sdcard (using computer) and copying qsb file there.
- Insert sdcard into phone
- Enter factory menu by powering off and then turning it on using POWER BUTTON + VOLUME DOWN
- There's an "SD Update" option, use it.
After that, my phone booted successfully!
Hooray. BUT: the first problem ("1. When I press/hold Volume + button and plug in usb cable , the phone vibarte 2 times . ") persisted
So, still haven't found a way to use miflash again
If anyone finds a way to solve this one, I will buy him a beer. Or a cat.
---------- Post added at 05:29 PM ---------- Previous post was at 05:28 PM ----------
If links are allowed here, you will find both rom and info here:
http://www.needrom.com/download/lenovo-z90-7-vibe-shot/
I tried the qsb files but my phone simply ignore them on the external sd , i saw some ppl that put them on the internal sd but i ve no access to the drive.
zahidbd2 said:
I have a phone Lenovo Vibe shot z90a40 . Few days ago I have successfully flashed firmware with root facilities with Miflash . Phone was working fine . Then I tried to flash again another firmware with QFIL . I marked the options "Reset after Download" . After downloding the new ROM my vibe shot never start , it always stuck on Lenovo logo/text .
The problem are below -
1. When I press/hold Volume + button and plug in usb cable , the phone vibarte 2 times . So Miflash/QFIL could not detect com port .
2. I could not enable usb debugging mode because my phone never startup after last flashing , so ' adb reboot edl' command not working . device not found .
3. Also I can't enter any Mode , so I could not reset data , could not update from any update.zip from recovery .
4. If I press and hold volume + , volume - and power button at same time , PC detect comport as 9006 , its shows not writable .
5. I tried eMMC downloader to switch to Download mode but failed . :crying:
Please help me . Thanks
Click to expand...
Click to collapse
Hi,
here is my solution if can help.
I had on my vibe shot s208 rooted ROW. It stacked after SU update in boot loop.
1. I did wipe data without formatting from recovery mode (Vol+ and Vol- and Power button. When Logo is on release power button and hold Vol+ and Vol - until you are in recovery mode). STILL boot loop.
2. I did wipe data with formatting from the same menu. - STILL boot loop.
3. I did factory reset from recovery menu (Vol - and Power after logo is on release Power and hold Vol - until you get recovery mode) - STILL boot loop.
Then I did next:
1. I downloaded and installed QFIL (QPST_2.7.422) - I am not allowed to post links yet.
2. I have connected OTG adapter to phone. Phone was off.
3. then connected OTG to PC. It was some HDD activities but I did not hear any sound.
4. press Vol- for as long as something is going on - HDD activities. Then I think came up sound too - but not sure.
5. I had installed Qualcomm USB drivers from before I suppose.
6. Because I couldn't see my device as ...908 I disconnected and connected again usb cable... then I got my device as ...908 in device manager, but it was written "RECONNECTED" or similar in front of word "QUALCOM".
7. Then just follow instructions for QFIL. and ROM will be installed.
First I have installed INTERNATIONAL no root ROM. But because I needed phone to be rooted in order to use data recovery software I flashed again with s240 ROOTED. When I flashed second time I did not use OTG, just direct usb cable connection to PC, and my phone was again recognized after I reconnected usb cable and in device manger was "RECONNECTED" in front of word "QUALCOM".
Hello and thanks!
Could you please provide more details regarding last step - quoted below?
Did you use the same software for flashing? What state was the phone in? How did you get it there?
dejxda said:
First I have installed INTERNATIONAL no root ROM. But because I needed phone to be rooted in order to use data recovery software I flashed again with s240 ROOTED. When I flashed second time I did not use OTG, just direct usb cable connection to PC, and my phone was again recognized after I reconnected usb cable and in device manger was "RECONNECTED" in front of word "QUALCOM".
Click to expand...
Click to collapse
daddy32 said:
Hello and thanks!
Could you please provide more details regarding last step - quoted below?
Did you use the same software for flashing? What state was the phone in? How did you get it there?
Click to expand...
Click to collapse
Well, after phone was recognized I did exactly the same procedure like in step 7. - Followed QFIL procedure (brows for 3 files and hit download).
lenovo vibe shot z90-7 brick
Hi.Before few days i had to flash an official rom on my vibe shot (s208) and after I was requested for OTA update the mobile stopped working.Trying to turn it on using recovery mode doesn't work.I tried several tricks but still nothing.The recovery mode,though,seems to work.But when I try to run a zipped rom on the external sd fails.I tried MiFlash too.When flashing begins it stops with the following notification:faulted function(0x80070001:WriteFile position 0x00000004000000,size 1048576).I also tried QFIL.I get this notification:Qualcomm HS-USB Diagnostics 9006(COM 5).I am desperate.I find no way to fix my mobile.pls help!
How To fix This Issue
I had a similar problem 2 days ago. I tried all methods but was unsuccessful. My computer couldn't detect my port as Qualcomm HS-USB QDLoader 9008 but rather Qualcomm HS-USB Diagnostic 9008 .
I found a way to fix that driver issue and i was able to flash my phone. And now My lenovo vibe shot is back to life.
I am not allowed to post links yet but i have provided the name of the sites
I hope this works for you
First Make sure your phone is turned off. U can do that by booting to recovery mode and sellect shutdown
Step 0
Download the right firmware for your device. I use other ones they didnt work.
This one worked perfectly for my device firmware version S118: Z90a40_USR_S118_1505272046_Q2020131.4_ROW_qpst.7z
Find it at boycracked forum or xda-developers forum
Step 1
Disable driver signature enforcement
Find the steps here
Step 2
Install the qdLoader HS-USB Driver
Find the steps at androidbrick
at this point your computer cant still recognise the device as Qualcomm HS-USB QDLoader 9008. You have to do the next step
Step 3
Manually Install VCOM Drivers on your Computer. This will enable your computer to detect your device as Qualcomm HS-USB QDLoader 9008
Find the steps at hovatek forum
Step 4
Head to this site and use the second method to flash your phone
( SECOND METHODS ) Installing the firmware using QPST/QFIL
Find the steps here
_ go to boycracked blog
dejxda said:
Hi,
3. then connected OTG to PC. It was some HDD activities but I did not hear any sound.
Click to expand...
Click to collapse
How do you connect your OTG to your PC?
This is how it looks...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How I fixed this
I fixed it installing a update.zip via recovery (vol + plus vol - plus power) I found here
http://forum.xda-developers.com/andr...posed-t3409989
This not fixed the phone , but allowed me to unlock bootloader entering in fastboot mode (vol + plus vol - plus plug usb) using this
http://lenovo-forums.ru/topic/18149-...B0-bootloader/
Then I was allowed to install TWRP as explained here
http://lenovo-forums.ru/topic/18150-...-by-sevenmaxs/
Then I was able to go to TWRP terminal and type
reboot edl
Phone rebooted into downloader mode and I was able to install this rom with QFIL
http://www.needrom.com/download/leno...encn-unlocked/
and I restored NVRAM with a qcn file I found in Ebay after putting the phone in diagnostics mode. Then I changed imeis, meid and esn to the original ones I found in the box. Phone fixed.
Just note that this file was for a Z90-7 rom and it will not work with a Z40a20 rom.
Hope this helps someone.
Lenovo Vibe shot z90a40 unbircked sucessfully
i posted a video on youtube about it where i sucessfully unbrick the device
josepgb said:
I fixed it installing a update.zip via recovery (vol + plus vol - plus power) I found here
http://forum.xda-developers.com/andr...posed-t3409989
This not fixed the phone , but allowed me to unlock bootloader entering in fastboot mode (vol + plus vol - plus plug usb) using this
http://lenovo-forums.ru/topic/18149-...B0-bootloader/
Then I was allowed to install TWRP as explained here
http://lenovo-forums.ru/topic/18150-...-by-sevenmaxs/
Then I was able to go to TWRP terminal and type
reboot edl
Phone rebooted into downloader mode and I was able to install this rom with QFIL
http://www.needrom.com/download/leno...encn-unlocked/
and I restored NVRAM with a qcn file I found in Ebay after putting the phone in diagnostics mode. Then I changed imeis, meid and esn to the original ones I found in the box. Phone fixed.
Just note that this file was for a Z90-7 rom and it will not work with a Z40a20 rom.
Hope this helps someone.
Click to expand...
Click to collapse
Hi, I managed to install twrp ( Chinese) but I can't install any rom .. After successful flashing ROM via twrp, system reboot with lenovo logo, then long vibrates.. When I connect it to PC. It show number of partition and need to format popup.. I tried different ROMs.. All via twrp. I don't use miflash or qfil.. Do I have to use miflash or qfil to solve the problem?? Mi or qfil?
I got this error in lenovo vibe x3 using QPST ..
any onehelp me?
Start Download
Program Path:E:\New folder\myphone\twrp3.0.2 QPST\prog_emmc_firehose_8974.mbn
Binary build date: May 13 2015 @ 14:41:37
QSAHARASERVER CALLED LIKE THIS: 'C:\Program Files\Qualcomm\QPST\bin\QSaharaServer.exe -p \\.\COM7 -s 13:E:\New folder\myphone\twrp3.0.2 QPST\prog_emmc_firehose_8974.mbn 'Current working dir: C:\Users\Ketul\AppData\Roaming\Qualcomm\QFIL
Sahara mappings:
2: amss.mbn
6: apps.mbn
8: dsp1.mbn
10: dbl.mbn
11: osbl.mbn
12: dsp2.mbn
16: efs1.mbn
17: efs2.mbn
20: efs3.mbn
21: sbl1.mbn
22: sbl2.mbn
23: rpm.mbn
25: tz.mbn
28: dsp3.mbn
29: acdb.mbn
30: wdt.mbn
31: mba.mbn
13: E:\New
19:11:49: ERROR: function: sahara_rx_data:194 Unable to read packet header. Only read 0 bytes.
19:11:49: ERROR: function: sahara_main:854 Sahara protocol error
19:11:49: ERROR: function: main:265 Uploading Image using Sahara protocol failed
Download Fail:Sahara Fail:QSaharaServer Failrocess fail
Finish Download
appu1988 said:
Hi, I managed to install twrp ( Chinese) but I can't install any rom .. After successful flashing ROM via twrp, system reboot with lenovo logo, then long vibrates.. When I connect it to PC. It show number of partition and need to format popup.. I tried different ROMs.. All via twrp. I don't use miflash or qfil.. Do I have to use miflash or qfil to solve the problem?? Mi or qfil?
Click to expand...
Click to collapse
miflash and qfil cannot help at this state.
go into twrp, and restore backup.
if you dont have backup, dont know how to help.
i cannot flash any other rom too with twrp.
I have bricked lg e988 indonesia firmware rooted,updated to kitkat 4.4.2,cwm 6.4.0.4
Due to some issue I factory reset from settg menu and the phone rebooted to cwm recvry mode
I tried to rebootd to system but fail
I tried to flash stock rom via adb sideload but fail too so does with lg flash tool
So I thght smtg wth cwm then I tried to flash twrp loki 2.6 and then stuck to lg logo only until now
Pls help
You're still soft bricked, just force your device into download mode and use LG Flash Tool to return back to stock and start again.
ShadySquirrel said:
You're still soft bricked, just force your device into download mode and use LG Flash Tool to return back to stock and start again.
Click to expand...
Click to collapse
Thank you for the respond. Mind if you share me on how to force my device into download mode?
I have tried the power + volume keys combination but nothing happened, back and stop at lg logo
Before i flash the twrp, i tried the LG Flash Tool, but i wont recognize the phone, something like usb connection issue
hotmatua.parulian said:
Thank you for the respond. Mind if you share me on how to force my device into download mode?
I have tried the power + volume keys combination but nothing happened, back and stop at lg logo
Before i flash the twrp, i tried the LG Flash Tool, but i wont recognize the phone, something like usb connection issue
Click to expand...
Click to collapse
If I remember correctly (please check threads here, it's been a long time since I've used this device, so memories are fading), download mode is activated when you press Volume Up (or both of volume buttons) and insert USB cable. I know that E98x has some strange button sequences, like rebooting to recovery is a two step operation (Volume Up + Power until navbar blinks, then power button twice, that's the only way mine wanted to boot into recovery), so please check around.
As far as USB connection issues, don't use USB3+ ports and if you're on Windows 8.1+ and later, run with Administrator privileges. I never experienced that one (used LGFlashTools from inside VirtualBox running Win XP for all my needs, I'm not a Windows user), so can't really help much but forums are full with explanations how.
ShadySquirrel said:
If I remember correctly (please check threads here, it's been a long time since I've used this device, so memories are fading), download mode is activated when you press Volume Up (or both of volume buttons) and insert USB cable. I know that E98x has some strange button sequences, like rebooting to recovery is a two step operation (Volume Up + Power until navbar blinks, then power button twice, that's the only way mine wanted to boot into recovery), so please check around.
As far as USB connection issues, don't use USB3+ ports and if you're on Windows 8.1+ and later, run with Administrator privileges. I never experienced that one (used LGFlashTools from inside VirtualBox running Win XP for all my needs, I'm not a Windows user), so can't really help much but forums are full with explanations how.
Click to expand...
Click to collapse
Thank you very much...now the phone is back to initial state. This what i've done:
1. Download LG Flash tool from http://lgflashtool.com/
2. Download LG USB Drivers from http://lgflashtool.com/
3. Install LG flash tool and LG USB Drivers
4. Plug usb cable to phone
5. Hold volume buttons and then plug the usb cable to PC (i use win 10)
6. Voila, the Download Mode icon is showed up
7. Run LG Flash Tool (Administrator privilege) & follow the instruction (i use e988 v20c stock firmware)
8. Phone back to normal (only if you use the correct stock firmware)
A very big thanks to ShadySquirrel
Hopefully this thread can also be used as reference for anyone who has the same issue as i had