Hello,
i have a problem with my proximity sensor... it simply doesn't work with CM 7 (neither the RCs nor the final 7.0.0), on HTC stock it worked properly (switched display off when i took the phone to my face while calling someone).
When i install Sensor List it shows constantly the Value 9 not regarding if i touch the sensor or hold the phone to my face.
I did a lot of research... but nothing helps.
Many people say that i should change the ro.lge.proximity.delay in build.prop.
But i dont have this value in build.prop. Tried adding it with recommended value 200 but no change.
Also tried the Proximity calibrator from this forum and Sensor Doctor from Marked. Both Apps crash (i think because it doesn't find the ro.lge.proximity.delay value in build.prop).
Also have the always force proximity sensor option in CM setting set.
What can i try? Someone else this issue?
And why isn't there a ro.lge.proximity.delay option in /system/build.prop?
Thanks a lot
to finish this post: i found out that it's a hardware issue, my proximity sensor seems to be defect
and now your warranty is void! xD
time to unroot?
Will unroot if other Hardware defects should appear...
Only this defect is to small to give My Vision away for some weeks
Same her my proximity sensor seems to be defect but i think it's maby dust on it.
As title says: since i rooted my desire hd and flashed a custom rom, the proximity sensor ( G-sensor) and compass aren't working anymore. Tried to calibrate, reset, hard reset, flashed other roms, nothing helped. While calibrating, nothing moved, not the levelers and not the needle of the compass.
What relation do they have together? Is it one part? Could it be a hardware problem or just software?
I noticed some threads about a locked G-sensor. Tried to "shake" them loose. No result. Who can and is willing to help me? thnx.
Mine proximity s. isn't working either. I guess I will take it apart and have a look at it, could be dust or smth.
-SmOgER said:
Mine proximity s. isn't working either. I guess I will take it apart and have a look at it, could be dust or smth.
Click to expand...
Click to collapse
I replaced my Earspeaker yesterday since the sound had been really bad for som time.. while doing this I removed loads of dust located behind the Grid at the top the phone.. doing this ofc fixed the sound, but i also made my Proximity sensor work again.. and made the GPS get a better signal.. so really try cleaning it.. does wonders...
stormyb said:
As title says: since i rooted my desire hd and flashed a custom rom, the proximity sensor ( G-sensor) and compass aren't working anymore. Tried to calibrate, reset, hard reset, flashed other roms, nothing helped. While calibrating, nothing moved, not the levelers and not the needle of the compass.
What relation do they have together? Is it one part? Could it be a hardware problem or just software?
I noticed some threads about a locked G-sensor. Tried to "shake" them loose. No result. Who can and is willing to help me? thnx.
Click to expand...
Click to collapse
Try a fresh install of an RUU (going back to stock).
If it doesn't work then it shouldn't be a software issue.
Normally rooting does not affect those things.
When I flashed cm7 to my DHD the proximity sensor stopped working. It was an issue with the sensitivity settings of the sensor not being correct for AOSP roms. I fixed it using the app in this thread.
http://forum.xda-developers.com/showthread.php?t=951858
hi i just recently bought a galaxy note 2 phablet, im very happy with it every thing works perfectly fine, however i did come across a slight problem which is bugging me alot, as i loaded the phone up it shows you all the tutorials and stuff, for panning and zooming in using motion control.... i did not realise the problem before as i was really happy to just get the phone after so long, My motion sensor and gyroscope functions are not working
i have tried everything from factory reset to restarting , taking the battery out and putting it back in, has anyone stumbled upon this problem, and is there a solution to this problem, whether this is a software glitch/problem or a hardware issue. if anyone can help me please and thanks in advance
*#0*# check there if they are working.
Sent from my GT-N7100 using xda premium
mariosraptor said:
*#0*# check there if they are working.
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
hi thank you for the quick reply, i had a look at what you asked me to do and i did manage to find all the settings, however it looks to me everything is working apart from the light sensor one, all the other settings came up as a PASS apart from the light sensor which came as level 0, which i dont know what that means, while i was on the sensor screen i swiped my hand across the sensor and the screen shifted colour from white to yellow, which is a good indication that it is working , however i went back on the operating system and tried the palm swipe and it did not work, niether did the quick glance, and the pan to zoom features are not working either, i did test the gyrocope settings and it came out as a PASS too, could you explain maybe why this may be happening and what does the level 0 on the light sensor option means, please and thank you , i really do appreciate it.
Lavel 0 says to all phones I have tried including mine. As long as the LUX changes it is working.
Now for your primary problem try to recalibrate gyroscope.
Do it by going settings-motion-advanced settings-gyroscope calibration.
If that does not help try clearing cache in recovery.
If that does not help then backup and try reflashing your rom.
Sent from my GT-N7100 using xda premium
darkgallion said:
hi i just recently bought a galaxy note 2 phablet, im very happy with it every thing works perfectly fine, however i did come across a slight problem which is bugging me alot, as i loaded the phone up it shows you all the tutorials and stuff, for panning and zooming in using motion control.... i did not realise the problem before as i was really happy to just get the phone after so long, My motion sensor and gyroscope functions are not working
i have tried everything from factory reset to restarting , taking the battery out and putting it back in, has anyone stumbled upon this problem, and is there a solution to this problem, whether this is a software glitch/problem or a hardware issue. if anyone can help me please and thanks in advance
Click to expand...
Click to collapse
Hello in response to your issues with the motion sensor. Have you installed a screen protector on your note 2? i noticed that after installing the screen protector on my Note 2 some of the motion actions did not work properly. So if you do have one on remove it and see if that corrects the issue. :good:
Useful help.
This was a very Useful thread, thanks. I've done the tests and came up vitha a fail when i tried my motion sensor. Is it likely to be broken? I'm going to reset to factory settings and pull of my screenprotector and se what happens before i do anything else. Is there anyone out there who has replaced the motion sensor? Is it soldered to the main board? Hard to replace?
Thanks beforehand. Tommie.
i thnk my sensor is nt wrkin... when i do the test, d color is alredy green nd isnt changin nd is vibratin continuosly?? is it broken or somthng lyk dat??
note 2 sensor help
mariosraptor said:
*#0*# check there if they are working.
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
can't get quick glance to work
*#06*# does nothing on my note 2 why? Sensor not working was but stopped for some reason?:crying:
Samsung Galaxy Note 2 Motion Sensor and Gyroscope not working
hi my samsung note 2 was working well for last 2 years bur recenrtly its motion sensor has stopped working.
i have checked all settings, it isnt working at all..
gyroscope and motionsensor tests are fail on checking. please help me, what to do?
I have had the exact same issue. The only way to fix it is to get the whole motherboard replaced. I went into Samsung store and they said that. Issue here is that it costs £145 to replace the main board. The sensors are on the main board itself and that is why it costs a lot to fix. I've been using my Note 2 with no gyroscope for a few months now, going to buy a new phone. Rather buy a brand new phone than get it fixed
just loosen the screw nearest to the microsd card. motion sensor is under it. it work on my phone.
gyroscope sensor
Hi,
my gyroscope is burned and i buy it and now i opened my phone and i don't know how to replace it. Any help is welcome...
haakhan said:
just loosen the screw nearest to the microsd card. motion sensor is under it. it work on my phone.
Click to expand...
Click to collapse
Yeahhh!!!
You are a Hero! I tried nearly everythink since January 2016! I took the screw out, shut down my phone, put it into download mode and pull the battery out.
Im not shure if a restart would do it alone, i did all to be shure. And it now works again. My srew was magnetized! Maybe that was the reason or the chip has
a loosen contact.
Up to now it works great! I thought my sensor was dead.
I have recently got my phone back from repair and I have done some tests on it. It seems the magnetic sensor isn't working, most compasses don't work and ones that do are way off and seem to be using the gyro not the magnetic sensor. Hardware test apps report the sensor as there but no readings. Also the pedometer does seem to work either in the fitbit app as it does not register any steps.
I have used the Sensor List app from the store and these seem to be the only 2 not working. Is this just me or does anybody else have this problem?
ashyx said:
I have recently got my phone back from repair and I have done some tests on it. It seems the magnetic sensor isn't working, most compasses don't work and ones that do are way off and seem to be using the gyro not the magnetic sensor. Hardware test apps report the sensor as there but no readings. Also the pedometer does seem to work either in the fitbit app as it does not register any steps.
I have used the Sensor List app from the store and these seem to be the only 2 not working. Is this just me or does anybody else have this problem?
Click to expand...
Click to collapse
just you mate all mine working fine
What did you use to determine they are working? I have used the native hardware test using the code *#*#3424#*#* and it seems to fail there too. Apparantly the hall sensor test which is the magnetic sensor is supposed to show the clock when a magnet is put near a blue square on the screen. On mine it doesn't, but instead it turns the screen off and I can hear a click . However the magnet is fairly powerful so it maybe affecting something else. There doesn't seem to be a pedometer test and all the other tests seem fine.
Thanks
My s4's gyro sensor stopped working one day. After some research, this is a pretty common issue. I really hope it can be fixed with just software, but I am willing to accept it's a hardware issue. Nothing I've tried works, including flashing to stock and calibration. I'm stuck here, and I'm wondering if there's a way to switch between portrait and landscape using the auto-rotate button in quick settings. on lollipop, by the way. thanks