Hy. I install some software to add the posibility to reset my tablet when my son put pasword and forget :silly:...al good for 2 days,but now my tablet is not switch on again,I try al the difrent combination with presing and hold difrent buttons but nothing.Strange is that if i conect on the USB my computer signal me the something is conecting...but under ODIN nothing apear.
What to do???
livirys said:
Hy. I install some software to add the posibility to reset my tablet when my son put pasword and forget :silly:...al good for 2 days,but now my tablet is not switch on again,I try al the difrent combination with presing and hold difrent buttons but nothing.Strange is that if i conect on the USB my computer signal me the something is conecting...but under ODIN nothing apear.
What to do???
Click to expand...
Click to collapse
At first charge your Tab for 4-5 hours,than try to Boot into Recovery mode and do a factory reset.
You will lost all your privat settings, also your look pin.
bierma32 said:
At first charge your Tab for 4-5 hours,than try to Boot into Recovery mode and do a factory reset.
You will lost all your privat settings, also your look pin.
Click to expand...
Click to collapse
I let'it charge 8 hours but nothing,If i try to but on recovery nothing apear on screen..is dead.Only when i conect to USB port it apear on my computer,but is UNKNON DEVICE.No ODIN no KIES nothing.I thing that is briked :crying:
Btw.Thx for your help.
hmmm
livirys said:
I let'it charge 8 hours but nothing,If i try to but on recovery nothing apear on screen..is dead.Only when i conect to USB port it apear on my computer,but is UNKNON DEVICE.No ODIN no KIES nothing.I thing that is briked :crying:
Btw.Thx for your help.
Click to expand...
Click to collapse
hey,
take your tab into a DARK room, power on like you would normally, look at the screen at an angle while holding down
the power on button, if no light emits from it, do the recovery boot, and if again odin mode.
if you see light emitting from your screen on regular boot do not shut tab down, take it directly to your computer
and connect open your my computer icon on desktop after get adb running, in adb type adb start-service [enter]
then, adb devices [enter] if it's connecting your device number will show. additionally ask your son specifically what happened,
dropped,submerged,power surge,left sitting in sun etc.
for odin try connecting your tab FIRST then fire up Odin and see if it grabs. keep you flashable firmware/kernel/recovery
ready.
now the device i used to have was a rockchip tab but, i had a similar problem.
if any results please post an update.
m
Try in a dark room...nothing.It stay for 24 hour at charge. When i conect to cumputer it apear as a device cal EMEI.But canot fiind drivers...
I try even with ADB but nothing
,,C:\Users\Iry>adb devices
List of devices attached"
I dont know what to do ...
livirys said:
Try in a dark room...nothing.It stay for 24 hour at charge. When i conect to cumputer it apear as a device cal EMEI.But canot fiind drivers...
I try even with ADB but nothing
,,C:\Users\Iry>adb devices
List of devices attached"
I dont know what to do ...
Click to expand...
Click to collapse
Problem Solved...Samsung replace this device becouse of motherboard problem...Thx a lot for trying to help to evrybady.
livirys said:
Try in a dark room...nothing.It stay for 24 hour at charge. When i conect to cumputer it apear as a device cal EMEI.But canot fiind drivers...
I try even with ADB but nothing
,,C:\Users\Iry>adb devices
List of devices attached"
I dont know what to do ...
Click to expand...
Click to collapse
bro; your device bricked. need special tool like easy jtag box..
shanavas74 said:
bro; your device bricked. need special tool like easy jtag box..
Click to expand...
Click to collapse
Thx man,problem solved.Samsung replace the device ))Have a nice day.
Related
I want to upgrade rom on may diamond but when conect the phone to my conputer the phone it just starts to charge. The computer does not detect him and I have activated usb conection on the phone.
I am using a standard miniusb cable used also for canon fotcamera, Nokia N95, motorola V3 (v360 L6, L7 etc.)
I did instaled Activesync on my computer but still no result.
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
R3PUBL1K said:
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Click to expand...
Click to collapse
I am using Win XP SP2 and I have tried every thing that you said but nothing.
band27 said:
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
I did uncheck that box but without any results so now I will try internal method. But I'll have to send the file to the phone via bluetooth and see if it works.
band27 said:
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
How much is it supose to take "Internal method"?
After pressing Vol_Down + Back button it showed the three color screen then it changed to a white screen with loading on it and it stays like that (after pressing Vol_Down + Back button I didn't press nothing else).
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
band27 said:
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
Click to expand...
Click to collapse
I have tried everything that you said and nothing.
The only diference is that now when I conect the cable to the phone it asks me witch mode to conect it (Activesync or storage), but the computer still doesn't see's it.
Tried another USB-cable?
chribruu said:
Tried another USB-cable?
Click to expand...
Click to collapse
I tried with 3 diferent cables.
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
band27 said:
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
Click to expand...
Click to collapse
It doesn't switch's to usb it only shows "serial". If I put it into bootmode while it is conected to USB it shows nothing, not "USB" or "Serial" it's blank.
I am begining to belive that there is a hardware problem in my phone.
Do you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
If this is a spam, plz forgive me
Well, 2 all. I booted my Diamond with a 6.5 ROM. Normallt, it worked well. But this time, the ROM got some mistake that when it was goin' to finish, it froze it still kept the static in 30 mins later, and I got to reset it. Then, my Diamond restarted, and... froze at the Bootloader screen (3 colors screen) ( I tried all things to recover it, searching on the web, but nothing's ok I plugged it into my PC and my PC doesn't recognize it ( anyone knows out there plz help!!!!!!!
which version of windows operating system are you using. also try to reset and then again go into bootloader MANUALLY by pressing volume down key. see if the pc detects. also do you have ur stock rom?
meteorain08 said:
If this is a spam, plz forgive me
Well, 2 all. I booted my Diamond with a 6.5 ROM. Normallt, it worked well. But this time, the ROM got some mistake that when it was goin' to finish, it froze it still kept the static in 30 mins later, and I got to reset it. Then, my Diamond restarted, and... froze at the Bootloader screen (3 colors screen) ( I tried all things to recover it, searching on the web, but nothing's ok I plugged it into my PC and my PC doesn't recognize it ( anyone knows out there plz help!!!!!!!
Click to expand...
Click to collapse
enter bootloader, connect to PC. in white bar the 'Serial' will change to 'USB'
then you can run customeRUU to flash again
if the PC don't detect, try on other PC.
Well, if u know how to up ROM via PC then tell me, because I often up ROM directly on my Diamond, not via PC. And I plugged it to PC and the word "Serial" disappeared, but the word "USB" did not display on the screen
Did you make MTTY befor instal 6.5 rom try to make it and reinstal the rom
:crying: Hi there, yesterday i tried to remove cwm from my galaxy gt-i8150 and i've referred to many solution they mentioned that do it same way as how i flashed cwm...but at last i failed, my SGW do turn up when i press the power button but it stuck at "Warning!! A custom OS can cause......." there have prompt to press volume up or down and a triangle exclamation mark at below (i dont know whether this is download mode or not)
When i pressed volume down button it reboot and then come back to this screen again, i've tried many times pressing volume down button and pull out & place back my battery, it still shown up this screen allover again. I viewed other unbricking solution thread but didn't found any situation same as mine. When i pressed volume up button nothing happen, i can't boot into recovery mode. please help ...:crying::crying::crying:
http://androidforums.com/galaxy-y-a...ne-using-odin-v1-85-also-fixes-bootloops.html
This link will help. But it's for galaxy Y. Download the stock ROM. (Its in the galaxy W forums) Boot into download mode is pressing Power button, Volume down and Menu button. Good luck mate.
patrickdass said:
This link will help. But it's for galaxy Y. Download the stock ROM. (Its in the galaxy W forums) Boot into download mode is pressing Power button, Volume down and Menu button. Good luck mate.
Click to expand...
Click to collapse
thanks for response sir, i already viewed many thread that were talking about this method, but the problem is when i press the power button to switch on my phone, it straight away goes to download mode after samsung logo shown up, i dont even have to use combo press to boot into download mode.
And nothing happen when i press volume up button that stated "continue" but volume down button do restart my phone and boot into download screen again. When i plugged in USB, pc couldn't detect my phone.. any solution..?
will_wl said:
thanks for response sir, i already viewed many thread that were talking about this method, but the problem is when i press the power button to switch on my phone, it straight away goes to download mode after samsung logo shown up, i dont even have to use combo press to boot into download mode.
And nothing happen when i press volume up button that stated "continue" but volume down button do restart my phone and boot into download screen again. When i plugged in USB, pc couldn't detect my phone.. any solution..?
Click to expand...
Click to collapse
try to install CWM again on your mob by using odin .. your mob should be detected when you press continue if you install Samsung drive on your pc
Ahmed.ragab said:
try to install CWM again on your mob by using odin .. your mob should be detected when you press continue if you install Samsung drive on your pc
Click to expand...
Click to collapse
yeap i do installed samsung driver on my pc from kies, but when im in download mode and plugged in usb windows message pop out "The USB device attached to the computer has malfunctioned and Windows does not recognize it." Whereas in odin when i click start is says "please connect phone"
will_wl said:
yeap i do installed samsung driver on my pc from kies, but when im in download mode and plugged in usb windows message pop out "The USB device attached to the computer has malfunctioned and Windows does not recognize it." Whereas in odin when i click start is says "please connect phone"
Click to expand...
Click to collapse
did you pressed continue while you are in download mode ?
Ahmed.ragab said:
did you pressed continue while you are in download mode ?
Click to expand...
Click to collapse
Yes i did
boot into download mode, then connect usb, windows show unknow device, odin not detected
will_wl said:
Yes i did
boot into download mode, then connect usb, windows show unknow device, odin not detected
Click to expand...
Click to collapse
I will upload Samsung drive for you to try
Ahmed.ragab said:
I will upload Samsung drive for you to try
Click to expand...
Click to collapse
Thankyou dude. Appreciate your reply
will_wl said:
Thankyou dude. Appreciate your reply
Click to expand...
Click to collapse
welcome Bro
here it is
http://www.mediafire.com/download/dg0s1jff9lmmgii/Samsung_Galaxy_W_Drivers.exe
Ahmed.ragab said:
welcome Bro
here it is
http://www.mediafire.com/download/dg0s1jff9lmmgii/Samsung_Galaxy_W_Drivers.exe
Click to expand...
Click to collapse
Too bad it still not working Thanks anyway.
Currently using windows 8, i think this is windows vista package? Should use driver for windows 8?
i seek into device manager and found Samsung Mobile Composite Device with exclamation mark on it, it say 'Device Cannot Start (Code 10)'
i spent my whole day on this problem already yet still haven't found a method to solve it :crying::crying:
will_wl said:
i seek into device manager and found Samsung Mobile Composite Device with exclamation mark on it, it say 'Device Cannot Start (Code 10)'
i spent my whole day on this problem already yet still haven't found a method to solve it :crying::crying:
Click to expand...
Click to collapse
I think as it is able to go in download mode there is a hope .. don't worry will be fixed
Follow this tutorial: http://forum.xda-developers.com/showthread.php?t=1467128
And download the firmware for your country from sammobile
Try to install adb driver (but first remove samsung usb driver if are installed)follow this guide:http://technologyandroid.com/2013/0...river-adb-di-qualsiasi-dispositivo-android-2/(it's in italian language)
then install samsung usb driver and check if odin recognize the device.
I have tried this guide yesterday for galaxy s2 and it works.
If after that don't works try to change the usb port , open odin by run as administrator and don't reboot odin.
Redwraith96 said:
Try to install adb driver (but first remove samsung usb driver if are installed)follow this guide:http://technologyandroid.com/2013/0...river-adb-di-qualsiasi-dispositivo-android-2/(it's in italian language)
then install samsung usb driver and check if odin recognize the device.
I have tried this guide yesterday for galaxy s2 and it works.
If after that don't works try to change the usb port , open odin by run as administrator and don't reboot odin.
Click to expand...
Click to collapse
when i click on the download link ads window pop-out and download does not go on, any idea?
miki2o said:
Follow this tutorial: http://forum.xda-developers.com/showthread.php?t=1467128
And download the firmware for your country from sammobile
Click to expand...
Click to collapse
Thankyou for trying to help
but seems like u don't get what is my problem now, when im in download mode and plugged in usb windows message pop out "The USB device attached to the computer has malfunctioned and Windows does not recognize it." Whereas in odin when i click start is says "please connect phone"
will_wl said:
when i click on the download link ads window pop-out and download does not go on, any idea?
Click to expand...
Click to collapse
install the latest USB drivers from here:http://uploaded.net/file/xdloq4jw (after installing the adb driver!!)
Windows 8 has major problems with compatibility with Odin ......that is probably the issue here.......
Try a PC with an older OS (preferably XP but vista or 7 should work)
If you're using vista or 7, run Odin as administrator.
If XP, run normally.
Then......
Make sure....
1) kies is NOT running (kill in task manager)
2) any installed firewalls/anti virus are disabled
3) have a selection of USB cables on hand to try if one doesn't work.
4) the USB port you are using needs to be a primary port (connected directly to the PC motherboard)......but try them all anyway....
Good luck....
Sent from my GT-I9100 using xda app-developers app
hi. I encountered a problem on my phone that doesn't boot properly.
When i tried to switch on my phone it showed at first the welcome msg "Samsung S4 mini gt-i9192" then after that, a pitch black screen, could not properly boot. But i learn that it does not turns off after the screen turns all black, i have to press the power button first to turn off the phone.
This problem started when i installed an app with some compatibility problems.
I wanted to root my phone hoping that can solve the problem, but then again a problem occurred when i tried to connect my phone to my laptop. It fails to install MTP usb device to my computer. I tried connecting it again provided that samsung kies was installed but again failed to connect my phone. Therefore i cant root my phone because i cant copy the files needed to root to my phone sd card.
I tried reinstalling kies, installing mtp drivers but nothing happened. I tried also restoring the previous boot image, restoring factory settings using recovery mode. But then problem still exist.
And fyi my phone can't mount any external sd card using recovery mode. And i think it was not in a debugging mode.
Phone: samsung s4 mini gt-i9192
firmware: i dont know
So basically, the problem is:
my phone wont boot,
i cant connect it to my pc
and i cant root it.
How should i root or even flash my phone when i cant connect to my computer? Do you have any idea on how to solve this problem? Any solutions or suggestions would be much appreciated. tnx.
champagneerantja
emzgames said:
snipped.
Click to expand...
Click to collapse
Have you tried putting the phone in download mode (Volume Down + Home + Power) and then connecting it your p,c , if not give this a shot it should pick up the drivers , once done , take out the usb cable hold the power the button to shut down and boot up .
since you have not mentioned your OS am assuming it is windows , try taking out Kies via some software like revo uninstaller which will remove all directories plus all registry entires then reinstall it if you really need it.
dovakinn said:
Have you tried putting the phone in download mode (Volume Down + Home + Power) and then connecting it your p,c , if not give this a shot it should pick up the drivers , once done , take out the usb cable hold the power the button to shut down and boot up .
since you have not mentioned your OS am assuming it is windows , try taking out Kies via some software like revo uninstaller which will remove all directories plus all registry entires then reinstall it if you really need it.
Click to expand...
Click to collapse
tried both yet still unable to connect.
emzgames said:
tried both yet still unable to connect.
Click to expand...
Click to collapse
dial *#0808# from your cell this would take you in usb settings, tick both mtp+adb , reboot , if they art already ticked uncheck them and check them again.
dovakinn said:
dial *#0808# from your cell this would take you in usb settings, tick both mtp+adb , reboot , if they art already ticked uncheck them and check them again.
Click to expand...
Click to collapse
im afraid i cant do this coz i cant boot my phone properly, up to welcome msg only then screen black out, but not power off.
emzgames said:
im afraid i cant do this coz i cant boot my phone properly, up to welcome msg only then screen black out, but not power off.
Click to expand...
Click to collapse
ohhh best take your cell to your nearest service center then . if you can't flash anything and usb is not getting detected i don't see any other option , maybe someone more experienced here can help.
dovakinn said:
ohhh best take your cell to your nearest service center then . if you can't flash anything and usb is not getting detected i don't see any other option , maybe someone more experienced here can help.
Click to expand...
Click to collapse
yah, thats what im thinking. i just brought this here hoping to solve this problem without going to a shop. thanks anyway.
aac. To me put your phone in download mode then use moborobo(a windows software) . Just open it and it will install the driver. If it dies not work then use adb installer . Remember you should have only any one of the software at one tim means either moborobo or kies or adb installer
Sent from my GT-I9001 using xda app-developers app
btw have you tried to boot the phone in safe mode ?? if it boots in safe mode it is still fixable without going to service center. power down , power up+ tap the menu button 3 or 4 times at THE same time to boot into safe mode if it boots into safe mode that means the hardware and OS is fine if it does not well then your out of luck.
dovakinn said:
btw have you tried to boot the phone in safe mode ?? if it boots in safe mode it is still fixable without going to service center. power down , power up+ tap the menu button 3 or 4 times at THE same time to boot into safe mode if it boots into safe mode that means the hardware and OS is fine if it does not well then your out of luck.
Click to expand...
Click to collapse
tnx man, but no luck..
Tried flashing a custom rom?
I was clearing the sde partitions and my phone suddenly went blank and it is not starting any more.
if I plug it to the laptop it shows charging symbol and "press any key to shutdown" message on left top corner.
It is not getting detected as qualcom or anything it is not booting to bootloader. sometimes it is showing tmobile boot image.
Phone model XT1789-04
Please help , how can blankfash and get the bootloader back? how to go to EDL mode from here ?
latadswapnil said:
I was clearing the sde partitions and my phone suddenly went blank and it is not starting any more.
if I plug it to the laptop it shows charging symbol and "press any key to shutdown" message on left top corner.
It is not getting detected as qualcom or anything it is not booting to bootloader. sometimes it is showing tmobile boot image.
Phone model XT1789-04
Please help , how can blankfash and get the bootloader back? how to go to EDL mode from here ?
Click to expand...
Click to collapse
The phone is unbrickable unless the hardware issue.
Sent from my LG-LS997 using Tapatalk
cgigate said:
The phone is unbrickable unless the hardware issue.
Sent from my LG-LS997 using Tapatalk
Click to expand...
Click to collapse
Can you please suggest a way to get into bootloader ? because currently whenever I switch on phone it shows tmobile logo(boot screen) and nothing happens and there is a message in left top corner "press any key to shutdown" . I tried to switch it on with volume down and power key but nothing happens blank screen.
Also it is not getting detected on my laptop not even as unknown device.
latadswapnil said:
Can you please suggest a way to get into bootloader ? because currently whenever I switch on phone it shows tmobile logo(boot screen) and nothing happens and there is a message in left top corner "press any key to shutdown" . I tried to switch it on with volume down and power key but nothing happens blank screen.
Also it is not getting detected on my laptop not even as unknown device.
Click to expand...
Click to collapse
Have you tried holding vol up and pwr to boot into bootloader?
41rw4lk said:
Have you tried holding vol up and pwr to boot into bootloader?
Click to expand...
Click to collapse
Yes I did try that and it only shows the Tmobile boot screen and "press any key to shutdown" on left top of screen as attached in the picture. :crying:
latadswapnil said:
Yes I did try that and it only shows the Tmobile boot screen and "press any key to shutdown" on left top of screen as attached in the picture. :crying:
Click to expand...
Click to collapse
Make sure you're using a 2.0 port from your mobo, not a hub and not a 3.0+ port.
Unplug your phone and try entering these commands one at a time, you might need to unplug before each command.
This all depends on whether you had your bootloader unlocked, adb enabled, etc. You put yourself in a weird state.
Unplug, open cmd prompt and enter
fastboot reboot bootloader it should say waiting for device
plug in your phone and hopefully it'll get you there. If not, repeat above and try
adb reboot bootloader
following the same procedure
fastboot reboot recovery
like above
adb reboot recovery
Hopefully one of those will get you somewhere where you can try to reflash the phone, factory reset, whatever it takes.
Since your pc doesn't recognize your device... who knows.
Last resort
Fastboot oem blankflash
If that works you should be ready to blankflash
41rw4lk said:
Make sure you're using a 2.0 port from your mobo, not a hub and not a 3.0+ port.
Unplug your phone and try entering these commands one at a time, you might need to unplug before each command.
This all depends on whether you had your bootloader unlocked, adb enabled, etc. You put yourself in a weird state.
Unplug, open cmd prompt and enter
fastboot reboot bootloader it should say waiting for device
plug in your phone and hopefully it'll get you there. If not, repeat above and try
adb reboot bootloader
following the same procedure
fastboot reboot recovery
like above
adb reboot recovery
Hopefully one of those will get you somewhere where you can try to reflash the phone, factory reset, whatever it takes.
Since your pc doesn't recognize your device... who knows.
Last resort
Fastboot oem blankflash
If that works you should be ready to blankflash
Click to expand...
Click to collapse
Yes bootloader was unlocked and adb was enabled also phone was rooted.
I am trying what you have suggested but its not working till now. I tried on USB 2.0 ports and 3.0 as well but nothing happens. neither blankflash executes nor any of fastboot or adb commands executes.
will linux OS help ?
latadswapnil said:
Yes bootloader was unlocked and adb was enabled also phone was rooted.
I am trying what you have suggested but its not working till now. I tried on USB 2.0 ports and 3.0 as well but nothing happens. neither blankflash executes nor any of fastboot or adb commands executes.
will linux OS help ?
Click to expand...
Click to collapse
Never hurts to try, the thing is your phone is in some limbo state and your pc doesn't doesn't see it. I can't imagine that linux will help much. Have you tried holding the power button for a minute or so? I don't know what the sde partition is honestly, but obviously you shouldn't have messed with it. What lead you to that partition and what exactly did you do?
You might uninstall your moto drivers, adb drivers, and fastboot drivers and see if plugging your phone in will detect on your pc as new hardware. Might try installing qualcomm diag drivers to see it it will recognize your phone. I afraid that until your pc sees it, any command is pointless since it can't communicate with your phone.
41rw4lk said:
Never hurts to try, the thing is your phone is in some limbo state and your pc doesn't doesn't see it. I can't imagine that linux will help much. Have you tried holding the power button for a minute or so? I don't know what the sde partition is honestly, but obviously you shouldn't have messed with it. What lead you to that partition and what exactly did you do?
You might uninstall your moto drivers, adb drivers, and fastboot drivers and see if plugging your phone in will detect on your pc as new hardware. Might try installing qualcomm diag drivers to see it it will recognize your phone. I afraid that until your pc sees it, any command is pointless since it can't communicate with your phone.
Click to expand...
Click to collapse
SDE are mobile partitions and I was trying to delete modem partitions as I had installed pie modem on my device and I might have accidentally deleted the bootloader partition or something like that.
after holding power button for a minute nothing happens same screen appears and disappears as I have attached in my previous reply.
is there a button combination which can direct this device in edl mode?
laptop is not reading my device yet, I tried different laptops different ports and different cables. linux is also not reading the device.
please let me know if you know any way I can boot this in edl mode to blankflash. I tried that cable way green and black cable short thats not working either on this device.
latadswapnil said:
SDE are mobile partitions and I was trying to delete modem partitions as I had installed pie modem on my device and I might have accidentally deleted the bootloader partition or something like that.
after holding power button for a minute nothing happens same screen appears and disappears as I have attached in my previous reply.
is there a button combination which can direct this device in edl mode?
laptop is not reading my device yet, I tried different laptops different ports and different cables. linux is also not reading the device.
please let me know if you know any way I can boot this in edl mode to blankflash. I tried that cable way green and black cable short thats not working either on this device.
Click to expand...
Click to collapse
There is no key combo as far as I know to enter edl mode on this phone, and most likely it wouldn't solve your problem. You flashed pie modems on a TMO device, that has been done before and no one has been able to recover from that. Even if you were to somehow get your phone booting, you wouldn't have a baseband or any cell service.
41rw4lk said:
There is no key combo as far as I know to enter edl mode on this phone, and most likely it wouldn't solve your problem. You flashed pie modems on a TMO device, that has been done before and no one has been able to recover from that. Even if you were to somehow get your phone booting, you wouldn't have a baseband or any cell service.
Click to expand...
Click to collapse
While if the OP is correct, and the problem is that they replaced their bootloader, then that's exactly what edl mode is for. However, you're definitely right that there's no key combination. I've been trying to get my moto into edl for days. I even got the battery to die. It just makes other diagnostics more annoying when I need to charge. So far, from what I can tell, the MSM8998 in a Z2 force first of all plays by different rules, uses a different programmer, and is generally not going to respond to the stock "qualcomm unbrick" tutorials. If it gets into edl, then you might be able to blankflash. But I guess keep trying different things, from what I've read the drivers and usb ports are finicky even with phones where this is known to work. It is not known to work with TX1789, at least not with the ease it works in other snapdragon phones. It's actually a massive security vulnerability (if it works it allows arbitrary read/write from the lowest level of the chain of trust, bypassing most security by default. It's a total backdoor), it's just unfortunate we're on that side of the fence. It doesn't have to be that way, but it was designed to see all unsigned software as equally malicious.
latadswapnil said:
I was clearing the sde partitions and my phone suddenly went blank and it is not starting any more.
if I plug it to the laptop it shows charging symbol and "press any key to shutdown" message on left top corner.
It is not getting detected as qualcom or anything it is not booting to bootloader. sometimes it is showing tmobile boot image.
Phone model XT1789-04
Please help , how can blankfash and get the bootloader back? how to go to EDL mode from here ?
Click to expand...
Click to collapse
Does anybody have any new suggestion how I can get into EDL mode?
my phone is still stuck on to the screen where it says press any key to shutdown. It doesn't get detected at all on any USB port or with different cables.
Does anybody know if there are any EDL short points on motherboard or deep flashing cable?
although I tried cutting regular USB C cable for trying to short the two cables and force put it in edl mode but nothing worked yet.
If anybody has any suggestion please throw some light.