Develop Bugs

[Q] pls answer me ASAP urgentlyyyyyyyyyy !!

hello ,,
pls i have t-mobile galaxy s3 and its screen has broken :S and turned into black but the device still working ,, so i need to delete all my data from it cos im gonna change it by warranty !! so please help me to delete all my files without root !!
thanks in advance guys

Can you see anything on screen or just black ??

bikrame said:
Can you see anything on screen or just black ??
Click to expand...
Click to collapse
no just black

Do u have any hdmi output cable ?

bikrame said:
Can you see anything on screen or just black ??
Click to expand...
Click to collapse
bikrame said:
Do u have any hdmi output cable ?
Click to expand...
Click to collapse
what's hdmi cable ??

Its a cable to join phon with tv or laptop where you can view your phone screen on tv.
I dont think there is any option left for you then. Becoz for alll process you need to see whats on ur screen and u say your screen is all blank.
Sorry man

Find out if your TV support HDMI port...if it does and you are willing to cough up few bucks, get this to connect it
http://www.amazon.com/Skiva-Samsung...403295&sr=8-3&keywords=hdmi+samsung+galaxy+s3

**** !!
so what if i installed a new rom via odin ?

You can install a stock ROM through Odin. Only thing is that the only way you will see it has properly connected in Download mode is throuhg the Com: box in Odin and you probably won't know if it boots up or not.
Couple of things.
Try to get an HDMI cable from a friend or something and use the TV as a monitor.
What recovery are you using? You might be able to get someone to walk you through some screen clicks (that is if your screen even registers the touches) to wipe /data (either through recovery or through Settings>Security>Factory Reset) or even /mounts and pull off through your PC that way.
Best bet is to get an HDMI cable and then once you have your new phone, you'll have all the wonders that the cable provides on a fully functioning phone.
You could always pull the internal SD from ADB and wipe through that avenue as well.

while in recovery on cwm touch, I'm almost positive that volume rockers and power button still react to clicks

Woody said:
You can install a stock ROM through Odin. Only thing is that the only way you will see it has properly connected in Download mode is throuhg the Com: box in Odin and you probably won't know if it boots up or not.
Couple of things.
Try to get an HDMI cable from a friend or something and use the TV as a monitor.
What recovery are you using? You might be able to get someone to walk you through some screen clicks (that is if your screen even registers the touches) to wipe /data (either through recovery or through Settings>Security>Factory Reset) or even /mounts and pull off through your PC that way.
Best bet is to get an HDMI cable and then once you have your new phone, you'll have all the wonders that the cable provides on a fully functioning phone.
You could always pull the internal SD from ADB and wipe through that avenue as well.
Click to expand...
Click to collapse
thanks alot ,, but could you please tell me where could i find stock Rom for it !! and tell me all steps to do it cause i dont have much info about android

Use odin I guarantee thats the best bet .
Do this pull battery, then put it back in.
Hold home button first then volume down and power at same time for 6seconds after right after 6 seconds release all buttons at once then immediately press vol up for half a second
Now the test to see if its in download mode connect to Odin plug usb into pc if u see "com" in one of the ports you are good to flash the stock tar file in the Pda section only
Remember to follow the steps they are timed as I have tested the time it takes to boot into download mode
First download the following files on your pc in order .Here is the files first is odin which is the tool to flash to stock. Extract it to a desktop folder named odin .Next is the usb drivers download and install and next and last is the actual firmware .tar file to flash in odin And only select pda section then find file and click start when says pass/reset its complete
1# http://hotfile.com/dl/161620048/6c6d559/Odin3_v3.07.rar.html
2# http://hotfile.com/dl/167907224/256bf74/T-Mobile_T999_GSIII_Samsung_USB_Driver_v1_4_6_0.exe.html
3# http://hotfile.com/dl/179539523/d0bd79a/SGH-T999_TMB_T999UVDLJA_T999TMBDLJA_Original.zip.html
Sent from my SGH-T999 using xda app-developers app

lojak29 said:
Use odin I guarantee thats the best bet .
Do this pull battery, then put it back in.
Hold home button first then volume down and power at same time for 6seconds after right after 6 seconds release all buttons at once then immediately press vol up for half a second
Now the test to see if its in download mode connect to Odin plug usb into pc if u see "com" in one of the ports you are good to flash the stock tar file in the Pda section only
Remember to follow the steps they are timed as I have tested the time it takes to boot into download mode
First download the following files on your pc in order .Here is the files first is odin which is the tool to flash to stock. Extract it to a desktop folder named odin .Next is the usb drivers download and install and next and last is the actual firmware .tar file to flash in odin And only select pda section then find file and click start when says pass/reset its complete
1# http://hotfile.com/dl/161620048/6c6d559/Odin3_v3.07.rar.html
2# http://hotfile.com/dl/167907224/256bf74/T-Mobile_T999_GSIII_Samsung_USB_Driver_v1_4_6_0.exe.html
3# http://hotfile.com/dl/179539523/d0bd79a/SGH-T999_TMB_T999UVDLJA_T999TMBDLJA_Original.zip.html
Sent from my SGH-T999 using xda app-developers app
Click to expand...
Click to collapse
thanksssss so much for ur help
i will try it and hope it work :good:

[Q] Need Help :( :( Bricked SGW

:crying: Hi there, yesterday i tried to remove cwm from my galaxy gt-i8150 and i've referred to many solution they mentioned that do it same way as how i flashed cwm...but at last i failed, my SGW do turn up when i press the power button but it stuck at "Warning!! A custom OS can cause......." there have prompt to press volume up or down and a triangle exclamation mark at below (i dont know whether this is download mode or not)
When i pressed volume down button it reboot and then come back to this screen again, i've tried many times pressing volume down button and pull out & place back my battery, it still shown up this screen allover again. I viewed other unbricking solution thread but didn't found any situation same as mine. When i pressed volume up button nothing happen, i can't boot into recovery mode. please help ...:crying::crying::crying:

http://androidforums.com/galaxy-y-a...ne-using-odin-v1-85-also-fixes-bootloops.html
This link will help. But it's for galaxy Y. Download the stock ROM. (Its in the galaxy W forums) Boot into download mode is pressing Power button, Volume down and Menu button. Good luck mate.

patrickdass said:
This link will help. But it's for galaxy Y. Download the stock ROM. (Its in the galaxy W forums) Boot into download mode is pressing Power button, Volume down and Menu button. Good luck mate.
Click to expand...
Click to collapse
thanks for response sir, i already viewed many thread that were talking about this method, but the problem is when i press the power button to switch on my phone, it straight away goes to download mode after samsung logo shown up, i dont even have to use combo press to boot into download mode.
And nothing happen when i press volume up button that stated "continue" but volume down button do restart my phone and boot into download screen again. When i plugged in USB, pc couldn't detect my phone.. any solution..?

will_wl said:
thanks for response sir, i already viewed many thread that were talking about this method, but the problem is when i press the power button to switch on my phone, it straight away goes to download mode after samsung logo shown up, i dont even have to use combo press to boot into download mode.
And nothing happen when i press volume up button that stated "continue" but volume down button do restart my phone and boot into download screen again. When i plugged in USB, pc couldn't detect my phone.. any solution..?
Click to expand...
Click to collapse
try to install CWM again on your mob by using odin .. your mob should be detected when you press continue if you install Samsung drive on your pc

Ahmed.ragab said:
try to install CWM again on your mob by using odin .. your mob should be detected when you press continue if you install Samsung drive on your pc
Click to expand...
Click to collapse
yeap i do installed samsung driver on my pc from kies, but when im in download mode and plugged in usb windows message pop out "The USB device attached to the computer has malfunctioned and Windows does not recognize it." Whereas in odin when i click start is says "please connect phone"

will_wl said:
yeap i do installed samsung driver on my pc from kies, but when im in download mode and plugged in usb windows message pop out "The USB device attached to the computer has malfunctioned and Windows does not recognize it." Whereas in odin when i click start is says "please connect phone"
Click to expand...
Click to collapse
did you pressed continue while you are in download mode ?

Ahmed.ragab said:
did you pressed continue while you are in download mode ?
Click to expand...
Click to collapse
Yes i did
boot into download mode, then connect usb, windows show unknow device, odin not detected

will_wl said:
Yes i did
boot into download mode, then connect usb, windows show unknow device, odin not detected
Click to expand...
Click to collapse
I will upload Samsung drive for you to try

Ahmed.ragab said:
I will upload Samsung drive for you to try
Click to expand...
Click to collapse
Thankyou dude. Appreciate your reply

will_wl said:
Thankyou dude. Appreciate your reply
Click to expand...
Click to collapse
welcome Bro
here it is
http://www.mediafire.com/download/dg0s1jff9lmmgii/Samsung_Galaxy_W_Drivers.exe

Ahmed.ragab said:
welcome Bro
here it is
http://www.mediafire.com/download/dg0s1jff9lmmgii/Samsung_Galaxy_W_Drivers.exe
Click to expand...
Click to collapse
Too bad it still not working Thanks anyway.
Currently using windows 8, i think this is windows vista package? Should use driver for windows 8?

i seek into device manager and found Samsung Mobile Composite Device with exclamation mark on it, it say 'Device Cannot Start (Code 10)'
i spent my whole day on this problem already yet still haven't found a method to solve it :crying::crying:

will_wl said:
i seek into device manager and found Samsung Mobile Composite Device with exclamation mark on it, it say 'Device Cannot Start (Code 10)'
i spent my whole day on this problem already yet still haven't found a method to solve it :crying::crying:
Click to expand...
Click to collapse
I think as it is able to go in download mode there is a hope .. don't worry will be fixed

Follow this tutorial: http://forum.xda-developers.com/showthread.php?t=1467128
And download the firmware for your country from sammobile

Try to install adb driver (but first remove samsung usb driver if are installed)follow this guide:http://technologyandroid.com/2013/0...river-adb-di-qualsiasi-dispositivo-android-2/(it's in italian language)
then install samsung usb driver and check if odin recognize the device.
I have tried this guide yesterday for galaxy s2 and it works.
If after that don't works try to change the usb port , open odin by run as administrator and don't reboot odin.

Redwraith96 said:
Try to install adb driver (but first remove samsung usb driver if are installed)follow this guide:http://technologyandroid.com/2013/0...river-adb-di-qualsiasi-dispositivo-android-2/(it's in italian language)
then install samsung usb driver and check if odin recognize the device.
I have tried this guide yesterday for galaxy s2 and it works.
If after that don't works try to change the usb port , open odin by run as administrator and don't reboot odin.
Click to expand...
Click to collapse
when i click on the download link ads window pop-out and download does not go on, any idea?

miki2o said:
Follow this tutorial: http://forum.xda-developers.com/showthread.php?t=1467128
And download the firmware for your country from sammobile
Click to expand...
Click to collapse
Thankyou for trying to help
but seems like u don't get what is my problem now, when im in download mode and plugged in usb windows message pop out "The USB device attached to the computer has malfunctioned and Windows does not recognize it." Whereas in odin when i click start is says "please connect phone"

will_wl said:
when i click on the download link ads window pop-out and download does not go on, any idea?
Click to expand...
Click to collapse
install the latest USB drivers from here:http://uploaded.net/file/xdloq4jw (after installing the adb driver!!)

Windows 8 has major problems with compatibility with Odin ......that is probably the issue here.......
Try a PC with an older OS (preferably XP but vista or 7 should work)
If you're using vista or 7, run Odin as administrator.
If XP, run normally.
Then......
Make sure....
1) kies is NOT running (kill in task manager)
2) any installed firewalls/anti virus are disabled
3) have a selection of USB cables on hand to try if one doesn't work.
4) the USB port you are using needs to be a primary port (connected directly to the PC motherboard)......but try them all anyway....
Good luck....
Sent from my GT-I9100 using xda app-developers app

[Q] How to back from CW11 to Stock 4.2.1?

Hi,
I was using my Grand Duos I9082 with great CWM11 4.4.2..
But due to change my phone with LG G2 nowadays, I'll give my phone to a friend but he needs dual sim option..
So, I need to flash original rom to on it.. I've downloaded these files:
Duos4.2.2stock-TUR-I9082XXUBMHC-20130906121521.zip (975.573.674 bytes)
and
I9082XXAMC7_I9082OJVAMC1_TUR.zip (827.176.269 bytes)...
I'm not sure which one is suitable for Turkish stock rom..
And how can I flash one of the file (if possible, tell me which one is better) via Odin?
I think I'll choose as PDA but I'm not sure another options required for Odin process..
If some expert tell me the whole process?
Thanks..

COA said:
Hi,
I was using my Grand Duos I9082 with great CWM11 4.4.2..
But due to change my phone with LG G2 nowadays, I'll give my phone to a friend but he needs dual sim option..
So, I need to flash original rom to on it.. I've downloaded these files:
Duos4.2.2stock-TUR-I9082XXUBMHC-20130906121521.zip (975.573.674 bytes)
and
I9082XXAMC7_I9082OJVAMC1_TUR.zip (827.176.269 bytes)...
I'm not sure which one is suitable for Turkish stock rom..
And how can I flash one of the file (if possible, tell me which one is better) via Odin?
I think I'll choose as PDA but I'm not sure another options required for Odin process..
If some expert tell me the whole process?
Thanks..
Click to expand...
Click to collapse
Here's the process
1.Turn off the device.
2. Boot in into Download Mode (to enter into download
mode you have to: press and keep holding the power,
volume down and home buttons in the same time).
3. While the device is into Download Mode, connect the
Samsung Galaxy Grand device to the PC via USB
cable.
4. Now, ensure that ODIN recognize the device, and the
“added” message is displayed, and ID:COM section is
yellow or blue. Note: if not, you will have to close the
ODIN app, disconnect the device by removing the
USB cable, change the USB port from the PC and
reinstall the USB Grand drivers once again. Then,
repeat all the steps from above.
5. Now, if everything is ok you can move to the next
step.
6. From ODIN app click on the “PDA” button.
7. Browse and pick the extracted firmware file from your pc
8. Next, from ODIN click on “START” button.
9. The installation process should begin immediately,
and you must wait until the firmware is being flashed.
10. When into ODIN app the “pass” message will be
displayed and the ID:COM section will turn green,
then the firmware is completely installed.
11. Now, you can disconnect the USB cable from PC.
12. Reboot the Galaxy Grand device.
Note: the first boot after the installation
process will take longer than usual, just be
patient.
If you still face some problem you can refer to guides in the general section.
There are some great guides there.
Sent from my GT-I9082 using XDA Premium 4 mobile app

manthan29jamdagni said:
Here's the process
1.Turn off the device.
2. Boot in into Download Mode (to enter into download
mode you have to: press and keep holding the power,
volume down and home buttons in the same time).
3. While the device is into Download Mode, connect the
Samsung Galaxy Grand device to the PC via USB
cable.
4. Now, ensure that ODIN recognize the device, and the
“added” message is displayed, and ID:COM section is
yellow or blue. Note: if not, you will have to close the
ODIN app, disconnect the device by removing the
USB cable, change the USB port from the PC and
reinstall the USB Grand drivers once again. Then,
repeat all the steps from above.
5. Now, if everything is ok you can move to the next
step.
6. From ODIN app click on the “PDA” button.
7. Browse and pick the extracted firmware file from your pc
8. Next, from ODIN click on “START” button.
9. The installation process should begin immediately,
and you must wait until the firmware is being flashed.
10. When into ODIN app the “pass” message will be
displayed and the ID:COM section will turn green,
then the firmware is completely installed.
11. Now, you can disconnect the USB cable from PC.
12. Reboot the Galaxy Grand device.
Note: the first boot after the installation
process will take longer than usual, just be
patient.
If you still face some problem you can refer to guides in the general section.
There are some great guides there.
Sent from my GT-I9082 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Next time just give link to the all in one thread...
http://forum.xda-developers.com/showthread.php?t=2616816
And it's called CM11 (CyanogenMod 11) not CWM (Clockworkmod)

naufalhadyan said:
Next time just give link to the all in one thread...
http://forum.xda-developers.com/showthread.php?t=2616816
And it's called CM11 (CyanogenMod 11) not CWM (Clockworkmod)
Click to expand...
Click to collapse
Ya ohk.
Sent from my GT-I9082 using XDA Premium 4 mobile app

Thank you for your help..
Dear manthan29jamdagni & naufalhadyan,
Thank you for your great help..
I'd handled it by your steps easily..
Fully appreciated..
Thank you very very much...

Samsung Galaxy S4 ACTIVE shv-e470s Rooting Guide

Use this tutorial only with the Samsung Galaxy S4 ACTIVE shv-e470s smartphone.
CAUTION:THIS ROOTING METHOD IS ONLY FOR THE KOREAN VERSION SHV-E470S!!!
It was tested successfully on Samsung Galaxy S4 Active SHV-E470S Android version 4.2.2
Firmware version:E470SKSUANA1
Abstract:
Do not attempt to root any other smartphones with the files that you wil find in this articles.
This tutorial is destined to be used by advanced Android users.
I won’t be blamed in case you brick the phone or lose any data in the process!!!
Rooting the Galaxy S4 ACTIVE SHV-E470S will revoke its warranty. If you want to restore your phone's warranty then you will need to flash an official Samsung Android ROM OS.
Pre-requisites :
Download and install the Samsung USB Drivers on your computer
Disable Samsung KIES program if you have it installed on your computer
Disable any antivirus applications from running on your computer
Enable USB Debugging from Developer Options.
If Developer Options doesn’t appear in Settings, then you need to enable it.
go to Settings, then More, open About Device.
tap seven times on the Build Number.
you will now be enabling Developer Option, go back to main Settings section, scroll down and enable USB Debugging
Check your phone’s battery and make sure that there is at least 50% left before the device switches off
Read the entire post, don’t skip any steps and the guide should be completed in under ten minutes with success.
In case you have trouble completing the guide, then you are free to ask for extra help in comments
Download required files (see attachments)
Odin3 1.85
UPDATE-SuperSU-v1.93
unofficial_philz_touch_6.12.8-e470s
Process:
1. Copy the "UPDATE-SuperSU-v1.93.zip" into your phone internal or external memory
2. Extract the contents of the Odin zip file and place them on your computer’s desktop screen.
3. Power off the Galaxy S4 active shv-e470s now.
4. After that you have to boot the device in Android Download Mode (press and hold: volume down,home and power buttons}
5. Launch Odin on your PC as administrator
6. Connect the phone with your computer via USB cable.(make sure antivirus+firewall is now disabled!!)
7. Wait for ODIN to detect your device,(you should see the "added" message) then continue to the next step.
8. If the phone is not recognized by your PC, then you should re-install the Samsung USB Drivers.
9. Go to ODIN’s main window, click on PDA and then find the "unofficial_philz_touch_6.12.8-e470s.tar" Load it in ODIN.
10. Do not change any other Odin default settings
11. Make sure that the Re-Partition option is not enabled
12. When ready, hit the START button for the process to begin.
13. Don’t press any buttons until the process is complete
14. When ODIN completes the process it will show the PASS alert, then the phone will reboot in normal mode. You can unplug the device from PC when the Samsung Galaxy S4 active shv-e470s boot animation screen loads.
15. Now power off your phone again and boot in recovery mode (press and hold: volume up,home and power buttons)
16. Once in recovery mode,find and install the "UPDATE-SuperSU-v1.93.zip" .To do this,in the recovery menu choose the "install zip" option and then find the directory u have saved the zip file and choose it for installing.
17. Wait for the process to finish and then ur phone will reboot.once reboot u can download "root checker" from play store and verify that u have root access.
18. Have fun and enjoy your rooted SHV-E470s

Did anyone try with E470SKSUAND1 yet?

story said:
Did anyone try with E470SKSUAND1 yet?
Click to expand...
Click to collapse
I tried and it works.

req new download links
The download links has expired . please give me another links.thx

This phone is update to 4.4.2. Are we can't root our phone such as #1?

new files
nickserbanoiu said:
The download links has expired . please give me another links.thx
Click to expand...
Click to collapse
hello my friend....i just renewed the files.

Thanks you !
how about 4.4.2 root, can we use this tool to root?

story said:
I tried and it works.
Click to expand...
Click to collapse
Hi, I also have E470SKSUAND1, but my recovery mode only shows me 4 or 5 options, no install zip option. I looked for the cwm but the shv e470s isn´t supportet yet. How did you do it?

Hi, I need pit file for this phone or 2gb system dump. Pls help me. My phone is brick now.

shv-e470s
Thanh_GSM said:
Hi, I need pit file for this phone or 2gb system dump. Pls help me. My phone is brick now.
Click to expand...
Click to collapse
Bro!! did you repair your shv-e470s boot-loader ?
i have hard bricked my shv-e470s any help?

Does anyone try on E470SKSUCOE1? (lollipop 5.0.1)

Bump for lollipop E470SKSUCOH1 rooting...

Hi, I downgrade my Samsung Galaxy S4 Active (SHV-E470s) from Android 4.4.2 kitkat to Android 4.2.2 JellyBean, Odin says "PASS", it means i successfully flash the 4.2.2 jellybean firmware, then I try to reboot my phone, nothing happens, It won't turn on, I try to charge it but no response, no vibration, it is like completely dead, It is Hard brick? How can I unbrick and revive it? Thank you.

[Q] Wont enter download mode! Phone stuck in boot loop.

After downloading the new AT&T update yesterday my phone (No root) went thru the update process and completed and then restarted itself and ever since then has been stuck in a boot loop on the LG logo screen. Was going to do the flashing procedure but when I try to boot the phone in download mode the little box appears saying "download mode" but instead of the "firmware update" screen appearing shortly after that my screen just goes black again. Have tried every port using the stock chord on my computer (Windows 8.1, USB 3.0) and have tried every port on another computer (Windows 7, USB 2.0) and still the same thing every time. Have installed the proper LG drivers on both computers but still fails to recognize the phone correctly under device manager as well.
ANY HELP IS MUCH APPRECIATED!

Update to lollipop? Wow sorry to hear that OP. Did you pull out the battery? Sometimes that helps strangely.

squall458 said:
Update to lollipop? Wow sorry to hear that OP. Did you pull out the battery? Sometimes that helps strangely.
Click to expand...
Click to collapse
Update to lolipop went fine it was this update that enables VoLTE that screwed it up. I cant post link because I am a new member but google it and you will find it.
But yes pulled the battery out first to end the boot loop and thats where the original post picks up from.

Sometimes to get into Download Mode:
Remove Battery.
Press Volume Up.
While still pressing Volume Up, replace Battery.
Still pressing Volume Up, connect to p.c. by USB Cable. Phone should now enter Download Mode......

jac10000 said:
Sometimes to get into Download Mode:
Remove Battery.
Press Volume Up.
While still pressing Volume Up, replace Battery.
Still pressing Volume Up, connect to p.c. by USB Cable. Phone should now enter Download Mode......
Click to expand...
Click to collapse
Thanks for the tip but still the same outcome.

craincrizzy said:
Thanks for the tip but still the same outcome.
Click to expand...
Click to collapse
How is it recognized in dvice manger on your computer. USB port ? COM port ?

jac10000 said:
How is it recognized in dvice manger on your computer. USB port ? COM port ?
Click to expand...
Click to collapse
Shows up under other devices as "QHSUSB_BULK"

craincrizzy said:
Shows up under other devices as "QHSUSB_BULK"
Click to expand...
Click to collapse
Ok your G3 is brick, you can try that : http://forum.xda-developers.com/lg-g2/general/tool-unbrick-lg-g2-qualcomm-9008-board-t3072073

Thank you so much for pointing me to that program! Worked like a charm.
Sent from my LG-D850 using XDA Free mobile app

craincrizzy, I am having the same issue with my LG G3 D850. Device manager shows QHUSB_bulk. What steps did you take to get your issue resolve?

I'm at work right now but once I'm home I will give you a step by step.
Sent from my LG-D850 using XDA Free mobile app

craincrizzy said:
I'm at work right now but once I'm home I will give you a step by step.
Sent from my LG-D850 using XDA Free mobile app
Click to expand...
Click to collapse
Thanks man, I will wait for you.
What driver do you use?
I have conecct a pin of the micro to the ground (how I read) and no more HQSUBS, now Windows detect a unknow device USB.

phillye said:
craincrizzy, I am having the same issue with my LG G3 D850. Device manager shows QHUSB_bulk. What steps did you take to get your issue resolve?
Click to expand...
Click to collapse
Before I even start just gonna let you know you have to flash the phone back to the stock firmware meaning you will lose anything saved on your phone but this is the only way to get it back functional.
Pre-requirements
1. Stock LG cord that came with phone
2. Desktop computer with USB 2.0 ports (3.0 wouldnt work for me)
3. Disable driver signature enforcement (Depends on OS as to how to do this so just google it. Takes just a few minutes)
*UNPLUG PHONE BEFORE STARTING*
1. Download and install the QDLoader HS-USB Driver here: http://www.androidbrick.com/download/qdloader-hs-usb-driver/
2. Plug your phone in while holding volume up to initiate "Download Mode" and it should now show up under "Ports" as "Qualcomm HS-USB QDLoader 9008"
3. Download and extract this: https://www.drive.google.com/file/d/0B_Hol5T47S-bYjNETmVPZkdWUms/view
4. Now download the stock fimware files (the .zip and .dll files) here: http://downloadandroidfiles.org/directory-php/?Directory=/LG%20G3/Stock%20Files/ATT%20D850
5. Extract the .tot file out of the .zip file and place it and your .dll file on your desktop.
6. Now open (be sure to right click and run as administrator!) BoardDiag which is located in the BoardDiag_V2_9 folder you downloaded in step 3.
7. If you need pictures to follow along with the next few steps go here: http://forum.xda-developers.com/lg-g2/general/tool-unbrick-lg-g2-qualcomm-9008-board-t3072073 and see the Attached Thumbnails at the bottom of the first post.
7. At the bottom under "Image Extraction" place the .tot file in the BIN field and make the DIR wherever you wish the files to be extracted to and then hit "Extract" and wait for process to finish.
8. Now under "Board Diag Test" check the boxes beside "AP check" and "EMMC TEST"
9. In the right column make sure "B2 (MSM8974AC)" is selected in dropdown "AP Chipset"
10. On the "Com Port" dropdown select the COM number your device shows up with in Device Manager.
11. In the "Target Dir" type the destination where you extracted the .tot file to in Step 7.
12. Click "START" and wait for process to finish. If the test passes the AP check and the EMMC TEST then you're good to go. If not then im afraid you have a hard brick and I cant help you there.
13. Uncheck "EMMC TEST" and check "RESTORE BOOT IMG" under "Restore Device"
14. In the dropdown beside "RESTORE BOOT IMG" choose the following in the order typed and hit "START" after choosing each file letting it flash the stock file to your phone: aboot--Backupgpt--boot--dbi--laf--Primarygpt--recovery--rpm--tz--sbl1
15. Your phone should now have the LG logo and underneath that say "Security Error".
16. Unplug your phone and pop your battery out and back in. Now plug your phone in while holding volume up for "Download Mode" and this time it should display the "Firmware Update" screen after a few seconds.
17. Now that you have the Firmware screen this guide will help you get your phone software back up and going (THIS IS WHERE YOU NEED A USB 2.0 PORT): http://www.androidrootz.com/2014/07/how-to-unroot-lg-g3-all-variants.html
Good Luck!!
Imporatant: If the OTA update boot looped your phone like mine DO NOT apply any OTA updates your phone tells you to apply because the same thing will happen again (Trust me I tried it)

craincrizzy, much thanks. Well written. I finally got the phone up. Good to be back in business. Thank you a million times again!

Good to hear. Glad I could help.
Sent from my LG-D850 using XDA Free mobile app