So i have a T-Mobile Galaxy S4 SGH-M919, and the story goes like this
so i decided to root it, and used CWM, and installed superuser. Superuser read that there was no binary, so i searched on forums to help me out. Someone said that installing MDB-setuidoff.zip would help, and now it is soft bricked, stuck on the Galaxy S4 logo reading
"Kernel Not Seandroid Enforcing"
So i figured, that it was a kernel problem, so i looked for the stock kernel, and upon attempted installation, CWM recovery said it was aborted and not installed. At this point i said screw it, and decided to try and unroot, but now using ODIN 3.07, using the stock tar.md5 from galaxys4root website
when i try to flash the PDA, it reads "FAIL" and an error
"<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sbl2.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl3.mbn
<ID:0/006> rpm.mbn
<ID:0/006> aboot.mbn
<ID:0/006> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)"
i can still reach odin, and recovery mode, but need help getting a working phone again. Completely out of ideas, maybe someone can chime in and help? I don't mind going back into stock unrooted state, or some kind of different root/rom as long as its stable. Help me get my phone back!
thanks in advance
Get the stock firmware from Sammobile . com
My S4 Is Insane
Deviant Team Member
The Sickness said:
Get the stock firmware from Sammobile . com
My S4 Is Insane
Deviant Team Member
Click to expand...
Click to collapse
do i have to be a premium member, or is something wrong with their site, it wont let me download the firmware, page just says "user is not a premium member"
thewrongkyle said:
do i have to be a premium member, or is something wrong with their site, it wont let me download the firmware, page just says "user is not a premium member"
Click to expand...
Click to collapse
Just register
My S4 Is Insane
Deviant Team Member
Related
Here's the error I get:
Code:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> sbl2.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks guys!
The phone is an I747 from AT&T.
I'm trying to flash the Rogers ROM on it because I am on a Rogers plan and the AT&T version is full of bloatware.
bump
Try downloading the file again. I would also try another usb slot or even pc
Sent from my SAMSUNG-SGH-I747M
mymusicathome said:
Try downloading the file again. I would also try another usb slot or even pc
Sent from my SAMSUNG-SGH-I747M
Click to expand...
Click to collapse
Just tried it again. It keeps failing at sbl2.mbn it seems.
If it means anything, I just noticed in download mode it says
Code:
SECURE CHECK FAIL : sbl2
SevKempf said:
Here's the error I get:
Code:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> sbl2.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks guys!
The phone is an I747 from AT&T.
I'm trying to flash the Rogers ROM on it because I am on a Rogers plan and the AT&T version is full of bloatware.
Click to expand...
Click to collapse
I may be wrong but I don't think you can flash the stock ATT ROM on a Rogers device and vice versa. Also, the ATT ROM contains a different modem that may not work well for us on Rogers. Your best bet is to keep the ATT ROM and freeze/delete the bloatware using Titanium Backup Pro and flash the Rogers modem.
Or run a custom ROM.
Tony_YYZ said:
I may be wrong but I don't think you can flash the stock ATT ROM on a Rogers device and vice versa. Also, the ATT ROM contains a different modem that may not work well for us on Rogers. Your best bet is to keep the ATT ROM and freeze/delete the bloatware using Titanium Backup Pro and flash the Rogers modem.
Or run a custom ROM.
Click to expand...
Click to collapse
Yeah, I'm currently running CM10 but I find it has WAY too many bugs for me to use it, things constantly crashing, graphical glitches. The LED doesn't light up for anything except charging.
I originally did use TiBa to delete the bloat, no problem. Except AT&T replaces the Address Book with their own version the "AT&T Address Book" which syncs with some AT&T server every time I open it, super annoying.
Then why not try using one of the custom ICS/JB stock-based ROMs? As he said, i'm pretty sure it's impossible to flash a Rogers ROM on an AT&T device.
And.... which build of CM10 are you using? You could always try Task & Ktoonsez CM10-based ROM. Never experience a graphical glitch (though, i never did even on older CM10 builds, either), hardly ever have anything crash..... and as far as i'm aware, even in stock CM10, you actually have to go into the settings or find an app and manually set up the notification LED colors and what they blink for.
elementaldragon said:
Then why not try using one of the custom ICS/JB stock-based ROMs? As he said, i'm pretty sure it's impossible to flash a Rogers ROM on an AT&T device.
Click to expand...
Click to collapse
Where can I find one of these ROMs? I've searched for them but I haven't found anything. I asked someone and they suggested an AOSP, but I wasn't able to find any, so I used a AOKP ROM and when I booted the phone all that displayed was some 8bit looking gradient from Yellow to Purple, got worried and rebooted my phone and reinstalled Cyanogenmod.
elementaldragon said:
And.... which build of CM10 are you using? You could always try Task & Ktoonsez CM10-based ROM. Never experience a graphical glitch (though, i never did even on older CM10 builds, either), hardly ever have anything crash..... and as far as i'm aware, even in stock CM10, you actually have to go into the settings or find an app and manually set up the notification LED colors and what they blink for.
Click to expand...
Click to collapse
I installed Cyanogenmod from the ROM Manager app. This ROM, specifically.
Also, when I install a ROM, can I do it from CWM? Or do I need to install using Odin?
SevKempf said:
Where can I find one of these ROMs? I've searched for them but I haven't found anything. I asked someone and they suggested an AOSP, but I wasn't able to find any, so I used a AOKP ROM and when I booted the phone all that displayed was some 8bit looking gradient from Yellow to Purple, got worried and rebooted my phone and reinstalled Cyanogenmod.
I installed Cyanogenmod from the ROM Manager app. This ROM, specifically.
Also, when I install a ROM, can I do it from CWM? Or do I need to install using Odin?
Click to expand...
Click to collapse
That link you provided shows that it points to a Galaxy S2 ROM in the url. The link itself didn't work though when i clicked on it.
Try this ROM: http://forum.xda-developers.com/showthread.php?t=1766684
I wonder if the problem you're having is related to the build.prop
ATT have a device model name d2att while the Canadian variants have device model name d2can.
Search the forums add I think I've read something about that.
Also, even though you want to flash a Rogers Rom, make sure you use an ATT modem.
Sent from my SGH-I747M using xda premium
what can be error sbl2.mbn than use Odin ?
i try use other usb port in notebook, any versions Odin (v. 1.85; 3.4; 3.7), reinstalling the USB drivers and use stock SGS3 USB but problem steel be
Thanks
Definitely try out Task650's AOKP rom, Its very stable and has very few (if any) bugs.
nate_benji said:
Definitely try out Task650's AOKP rom, Its very stable and has very few (if any) bugs.
Click to expand...
Click to collapse
i'm use Task650's AOKP rom at that moment, but they are not support extSdCard 64Gb and then i'm try upload stok JB 4.1.1. from Odin i recive a fail massage i think truble in sbl2.mbn
Code:
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I747MVLDLK4_I747MOYCDLK4_538866_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> sbl2.mbn
<ID:0/009> NAND Write Start!!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tybalt said:
Also, even though you want to flash a Rogers Rom, make sure you use an ATT modem.
Click to expand...
Click to collapse
Are you suggesting that I download both stock ROMs, extract them, then do a simultaneous mix and match of the parts in ODIN?
I have the AT&T i747 but want to have the reduced Rogers bloatware.
Anonymously_Unknown said:
Are you suggesting that I download both stock ROMs, extract them, then do a simultaneous mix and match of the parts in ODIN?
I have the AT&T i747 but want to have the reduced Rogers bloatware.
Click to expand...
Click to collapse
No, just get a cwm recovery and flash a AT&T modem.
Also, there's a unbloated AT&T stock ROM, why go for Rogers?
Go to twrp or cwm website and get the recovery for d2can instead of d2att. I'm not sure but it could be the source of your issue.
Sent from my SGH-I747 using xda app-developers app
Im having similar problem and need help too
I also have this secure check fail:sbl2 problem, but what I did was diffident. installed ParanoidKangDroid custom rom and then i realized that i use allshare play from stock rom pretty much so i decided to put back to stock my GS3. I used odin 3.0.7 to do that. I download the original stock rom from sammobile exactly the puerto rico version (were i live), but as i said it gives me the sbl2 fail problem.
---------- Post added at 05:19 AM ---------- Previous post was at 05:07 AM ----------
As you see Im a noobie here and I have another question. I like ParanoidKangDroid in my device but cant install allshare play so th question is: If i flash the [KERNEL][AT&T][AOSP/Touchwiz][JELLYBEAN][4/6/2013] KT747 - LJ7 - KTweaker, Can I install allshare play then? if yes what do i need to install it. Is there any other 4.2.2 rom that i can use the kernel mentioned above? or is there any rom which has touchwiz integrated?
sycol65 said:
but as i said it gives me the sbl2 fail problem.
Click to expand...
Click to collapse
I had downloaded the one from the stock firmware page and flashed it with the custom recovery to eliminate that issue. What you are experiencing is a bootloader mismatch.
Can you explain me the correct entire process to do that?
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
slb2.mbn error, fail
SevKempf said:
Here's the error I get:
Code:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> sbl2.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks guys!
The phone is an I747 from AT&T.
I'm trying to flash the Rogers ROM on it because I am on a Rogers plan and the AT&T version is full of bloatware.
Click to expand...
Click to collapse
This error is caused because a BAD USB CABLE. Please, use an original Samsung GGalaxy Cable. I had that problem with my GT-I9195. Fortunatelly it's working again.
The symptom was that i couldn't copy files from my computer to my smartphone.
I need help recovering my GS3, i tried using CF auto root to root my phone and i guess it didnt work because my phone doesnt boot past the samsung screen. I didnt have any custom recovery installed so i dont believe and thing was backed up. I am able to get into download mode and recovery mode. I tried flashing stock firmware using kies but it encounters a error saying its a problem with my phone, I tried using odin but it also gives me an error when flashing firmware saying
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_ATT_I747UCDLK3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1
What do I do to fix my phone?
FuTuRisTiC Zo3 said:
I need help recovering my GS3, i tried using CF auto root to root my phone and i guess it didnt work because my phone doesnt boot past the samsung screen. I didnt have any custom recovery installed so i dont believe and thing was backed up. I am able to get into download mode and recovery mode. I tried flashing stock firmware using kies but it encounters a error saying its a problem with my phone, I tried using odin but it also gives me an error when flashing firmware saying
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_ATT_I747UCDLK3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1
What do I do to fix my phone?
Click to expand...
Click to collapse
Ok I Installed Insecure Boot img via odin3 and my phone rebooted but now instead of it booting at the 1 second samsung screen it goes past it to the galaxy s 3 screen and just sits there. i also installed twrp, it let me mount everything but i cant u adb to push anything and it says i have no os installed. i dont know what moves to make anymore someone please help me out!!!
What version of Android did you have on your phone when it last worked, stock or custom ROM?
dawgdoc said:
What version of Android did you have on your phone when it last worked, stock or custom ROM?
Click to expand...
Click to collapse
its was a stock android rom i believe im not sure what version though.
Are you still able to get it into download mode?
Press and hold volume down + home + power at the same time
lemngo02 said:
Are you still able to get it into download mode?
Press and hold volume down + home + power at the same time
Click to expand...
Click to collapse
yes im able to go into download and recovery mode
lemngo02 said:
Are you still able to get it into download mode?
Press and hold volume down + home + power at the same time
Click to expand...
Click to collapse
oops didnt fully read your 1st post
lemngo02 said:
oops didnt fully read your 1st post
Click to expand...
Click to collapse
thats koo but the problem is i dont think my phone is rooted, i cant adb push using twrp cause my device wont show up when i adb devices
If you had the 4.3 bootloader on your phone, you cannot use Odin to flash a stock ROM.
Were you running the stock AT&T 4.3 ROM?
FuTuRisTiC Zo3 said:
thats koo but the problem is i dont think my phone is rooted, i cant adb push using twrp cause my device wont show up when i adb devices
Click to expand...
Click to collapse
Based on your Odin printout in the first post you were flashing a modified 4.1.1 kernel to install root. This should be fine if you were on either the 4.1.1 or 4.1.2 stock ROM. If you were on the 4.3 stock ROM your root attempt is probably the source of the problem.
IMPORTANT How to proceed from here depends on if you were on 4.3 or an earlier version of stock.
Also, since this forum is for AT&T and Canadian variants; I see the title of the first post says i747 - is this correct? It matters.
dawgdoc said:
Based on your Odin printout in the first post you were flashing a modified 4.1.1 kernel to install root. This should be fine if you were on either the 4.1.1 or 4.1.2 stock ROM. If you were on the 4.3 stock ROM your root attempt is probably the source of the problem.
IMPORTANT How to proceed from here depends on if you were on 4.3 or an earlier version of stock.
Also, since this forum is for AT&T and Canadian variants; I see the title of the first post says i747 - is this correct? It matters.
Click to expand...
Click to collapse
ok, not to jack his thread, but what if you are on the 4.3 bootloader? i didnt do what he did, but i am stuck in a similar situation. I am on the 4.3 bootloader, but i do have a custom recovery installed. problem is i get an error when i try to wipe. Ive tried flashing stock 4.3 rom via sideload in stock recovery, and modified rom though twrp. both roms install fine, but dont boot, but they do freeze in different points so i know something is being flashed. ive also tried wiping in cwm and stock. im bout ready to flash anything to this phone. oh and a nandroid restore fails after boot img flashes.
FuTuRisTiC Zo3 said:
its was a stock android rom i believe im not sure what version though.
Click to expand...
Click to collapse
From your message, you likely were on stock 4.3. Since you are able to get into recovery and download modes, you may try a restore via custom recovery. Please see the thread below on how to install custom recovery and do a stock restore ...
<http://forum.xda-developers.com/showthread.php?t=2658486>
fastludeh22 said:
ok, not to jack his thread, but what if you are on the 4.3 bootloader? I am on the 4.3 bootloader, but i do have a custom recovery installed.
Click to expand...
Click to collapse
I would then link you to the same thread Larry2999 provided.
dawgdoc said:
I would then link you to the same thread Larry2999 provided.
Click to expand...
Click to collapse
thanks. i had found that thread right after i posted. lets hope. its halfway downloaded. if that doesnt work,ill be posting a thread about the weird way i ended up here and detailed report of what i did and what ive tried...
dawgdoc said:
Based on your Odin printout in the first post you were flashing a modified 4.1.1 kernel to install root. This should be fine if you were on either the 4.1.1 or 4.1.2 stock ROM. If you were on the 4.3 stock ROM your root attempt is probably the source of the problem.
IMPORTANT How to proceed from here depends on if you were on 4.3 or an earlier version of stock.
Also, since this forum is for AT&T and Canadian variants; I see the title of the first post says i747 - is this correct? It matters.
Click to expand...
Click to collapse
audit13 said:
If you had the 4.3 bootloader on your phone, you cannot use Odin to flash a stock ROM.
Were you running the stock AT&T 4.3 ROM?
Click to expand...
Click to collapse
Yes the phone is AT&T and more than likely it was on 4.3 now what do i do
never mind folks i got it up and running my only option was to use the sd card so i found my adapter and fixed it. im on 4.1.2 now its updating software now im guessing to 4.3. thank you guys for all the help
FuTuRisTiC Zo3 said:
Yes the phone is AT&T and more than likely it was on 4.3 now what do i do
Click to expand...
Click to collapse
Before doing anything else, boot into recovery. If you are on a stock recovery the very first line will tell you that the system recovery is 3e
If you have one of the custom recoveries it will be different. If you have one of the custom recoveries, TWRP or CWM, you can use the link Larry299 posted earlier in this thread to restore your phone. If you are on the stock recovery and the 4.3 bootloader I don't know what to suggest.
dawgdoc said:
Before doing anything else, boot into recovery. If you are on a stock recovery the very first line will tell you that the system recovery is 3e
If you have one of the custom recoveries it will be different. If you have one of the custom recoveries, TWRP or CWM, you can use the link Larry299 posted earlier in this thread to restore your phone. If you are on the stock recovery and the 4.3 bootloader I don't know what to suggest.
Click to expand...
Click to collapse
I got everything back to normal im rooted on 4.1.2 and have a pending up date, is it safe for me to update via software updater or do i have to do something else
FuTuRisTiC Zo3 said:
I got everything back to normal im rooted on 4.1.2 and have a pending up date, is it safe for me to update via software updater or do i have to do something else
Click to expand...
Click to collapse
There is a chance that being rooted will prevent you from using the OTA official update. I've seen reports of people being able to update to the official 4.3 while rooted, but I've also seen reports of people not being able to update.
Before you make that update, bear in mind that the official 4.3 bootloader, its name ends in MJB, is the one that will prevent you from ever going back to an older bootloader. Some of the devs and the more experienced on here have no problem with that. Others do consider it an issue. An alternative is to install the leaked 4.3 bootloader, it's name ends in MJ2. That bootloader will allow you to downgrade to the 4.1.1 or 4.1.2 bootloaders, or so I have read. There is information about this in the development and the general forums for our device.
To muddy the waters more; if you intend to sim unlock your device without gettings codes from your carrier you need to do it from the 4.1.1 official ROM. A point you can not return to from the official 4.3 ROM, or so I've read.
I am having a huge booting issue with my Samsung Galaxy S3. Its a brand new one and I tried rooting it but it gave me this error:
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I can get to download mode, but not recovery nor does it boot into the Android OS. I tried putting back the stock OS and it gave me this error:
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've tried follow a bunch of these threads, but I can't seem to resolve my issue yet. I probably have that 4.3 bootloader which screwed everything up. Can someone help me resolve my issue? I literally got this phone today from AT&T. Thank you.
I have been running a rooted version of 4.3 (UCUBMK6) with TWRP recovery for some time, and want to do the OTA update to Kitkat. So I'll need to bring it back to stock first. I ran TriangleAway and rebooted to download mode afterward. Then I followed THIS guide to flash back to stock ROM 4.2.1 "KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5".
I tried several times with Odin 3.07, but every time it fails:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I then went back into download mode and flashed the rooted UCUBMK6 ROM, which works just fine (and also took it back from TWRP to stock recovery).
Does anyone have any idea how I can get it back to a stock, unrooted ROM, so that I can run OTA? Thx!
mobidutch said:
I have been running a rooted version of 4.3 (UCUBMK6) with TWRP recovery for some time, and want to do the OTA update to Kitkat. So I'll need to bring it back to stock first. I ran TriangleAway and rebooted to download mode afterward. Then I followed THIS guide to flash back to stock ROM 4.2.1 "KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5".
I tried several times with Odin 3.07, but every time it fails:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I then went back into download mode and flashed the rooted UCUBMK6 ROM, which works just fine (and also took it back from TWRP to stock recovery).
Does anyone have any idea how I can get it back to a stock, unrooted ROM, so that I can run OTA? Thx!
Click to expand...
Click to collapse
what bootloader are you running , also this ( http://forum.xda-developers.com/showthread.php?t=2589891 ) is a great thread and may help you make sure u read second or third post i dont remember witch . also ( http://forum.xda-developers.com/showthread.php?t=2581321 )
I tried to do the same for the update to kk. 3.09 said pass but bootlooped. Had to use 1.85, now on kk. Good luck.
Sent from my Note 3...making all others drool!
mobidutch said:
I have been running a rooted version of 4.3 (UCUBMK6) with TWRP recovery for some time, and want to do the OTA update to Kitkat. So I'll need to bring it back to stock first. I ran TriangleAway and rebooted to download mode afterward. Then I followed THIS guide to flash back to stock ROM 4.2.1 "KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user_low_ship.tar.md5".
I tried several times with Odin 3.07, but every time it fails:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I then went back into download mode and flashed the rooted UCUBMK6 ROM, which works just fine (and also took it back from TWRP to stock recovery).
Does anyone have any idea how I can get it back to a stock, unrooted ROM, so that I can run OTA? Thx!
Click to expand...
Click to collapse
Follow this. http://forum.xda-developers.com/show....php?t=2618447 .
I followed sections all sections 1 threw 3. At section 2 the link for the I317UCUBMK6-TZ-PARAM.zip did not work. I used this link instead.
http://www56.zippyshare.com/v/16559598/file.html
At section 3 don't be alarmed when it says it's downloading the update but it doesn't show percentages. It is downloading. In fact for me it automatically downloaded the 4.4.2 update instead of 4.3. It skipped it and went straight to kitkat. It took some time but I have Official KItkat 4.4.2.
Hit Thanks
Sent from my SAMSUNG-SGH-I317 using XDA Premium 4 mobile app
---------- Post added at 12:08 AM ---------- Previous post was at 12:07 AM ----------
djbrian52 said:
I tried to do the same for the update to kk. 3.09 said pass but bootlooped. Had to use 1.85, now on kk. Good luck.
Sent from my Note 3...making all others drool!
Click to expand...
Click to collapse
Whate are you talkin about 1.85? Instead of 3.09?
Sent from my SAMSUNG-SGH-I317 using XDA Premium 4 mobile app
You mentioned that you used Odin 3.07. I used 3.09 with no success. Had to use version 1.85.
Sent from my Note 3...making all others drool!
djbrian52 said:
You mentioned that you used Odin 3.07. I used 3.09 with no success. Had to use version 1.85.
Sent from my Note 3...making all others drool!
Click to expand...
Click to collapse
Lol i didnt even know 3.09 was out i just have it saved on my pc & just always use 3.07 works perfect
Sent from my SAMSUNG-SGH-I317 using XDA Premium 4 mobile app
help me pls
06SilveradoZ71 said:
Follow this. http://forum.xda-developers.com/show....php?t=2618447 .
I followed sections all sections 1 threw 3. At section 2 the link for the I317UCUBMK6-TZ-PARAM.zip did not work. I used this link instead.
http://www56.zippyshare.com/v/16559598/file.html
At section 3 don't be alarmed when it says it's downloading the update but it doesn't show percentages. It is downloading. In fact for me it automatically downloaded the 4.4.2 update instead of 4.3. It skipped it and went straight to kitkat. It took some time but I have Official KItkat 4.4.2.
Hit Thanks
Sent from my SAMSUNG-SGH-I317 using XDA Premium 4 mobile app
[SIZE=hi, my note 2 i317 got stuck on samsung logo & cnt get it to recovery mode. as i told that i need to flash the param files but the files that is link on the thread doesn't work. & you mention about the link that works. well i click it & it says files doesnt exist. do you think you can help me find a link or if you have the files that i needed. thank you so much
Click to expand...
Click to collapse
My n7100 got soft brick out of blue. it kept stuck on Logo and there was no way to make it to main menu. anyways i tried to flash stock rom that I found online and it gave me fail!, When I ran it again it stoped showing logo. instead it keeps showing update failure messege. any ideas how to fix it please
I have been running stock rom, never tried to root it and i have decent knowledge in using odin (I've done rooting and flashing roms many times before with my previous devices)
Mohammed Al Jubouri said:
My n7100 got soft brick out of blue. it kept stuck on Logo and there was no way to make it to main menu. anyways i tried to flash stock rom that I found online and it gave me fail!, When I ran it again it stoped showing logo. instead it keeps showing update failure messege. any ideas how to fix it please
I have been running stock rom, never tried to root it and i have decent knowledge in using odin (I've done rooting and flashing roms many times before with my previous devices)
Click to expand...
Click to collapse
this is what i get with odin
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007>
<ID:0/007> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I think you mesed up partition with some rom,so now you must flash with pit ,but dont lisent to me wait for someone who knows. I have this situation with mu sgs2 and i must to replace morherboard.
Sent from my GT-N7100 using XDA Free mobile app
when i run the device now the screen goes all white
i still can get easily to download mode with no issues
Help me guys
???
Try mskips toolkit from skipsoft.net. It has a recovery package that should fix your pit
Sent from my SM-G900F using Tapatalk
Hi,
I have a N7105 with stock firmware. I have not flashed any ROMS or anything like that on this phone.
I woke up this morning and found the phone on the 'Samsung Galaxy Note 2' boot screen.
I had to take the battery out to turn the phone off.
I booted into recovery mode and all these 'E: Error....' messages popped up.
I clicked on the 'reset data/factory settings option', it asked me to confirm. I selected Yes and more red 'E: Error' messages popped up.
I haven't been in this forum since I owned a Samsung Galaxy S and was flashing 'Darkys ROM' back in the day. So it has been 4-5 years since I last flashed or installed a ROM on a phone.
I need some help please with fixing my N7105. I believe that my only option is to flash a ROM or something via ODIN? Any help/guidance would be much appreciated.
Thanks!
layziebone said:
Hi,
I have a N7105 with stock firmware. I have not flashed any ROMS or anything like that on this phone.
I woke up this morning and found the phone on the 'Samsung Galaxy Note 2' boot screen.
I had to take the battery out to turn the phone off.
I booted into recovery mode and all these 'E: Error....' messages popped up.
I clicked on the 'reset data/factory settings option', it asked me to confirm. I selected Yes and more red 'E: Error' messages popped up.
I haven't been in this forum since I owned a Samsung Galaxy S and was flashing 'Darkys ROM' back in the day. So it has been 4-5 years since I last flashed or installed a ROM on a phone.
I need some help please with fixing my N7105. I believe that my only option is to flash a ROM or something via ODIN? Any help/guidance would be much appreciated.
Thanks!
Click to expand...
Click to collapse
yes, use odin, flash custom recovery and then install rom with recovery.
I think this is unfortunately SDS
Ahh this is so frustrating.
Just tried flashing stock rom again via ODIN and now I am getting this error in Odin..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Help Please!
read about SDS, cuz that's whatchappened to your device for 99%
Thanks.
I've done some research and found that the only fix is to take it in for repairs?
layziebone said:
Thanks.
I've done some research and found that the only fix is to take it in for repairs?
Click to expand...
Click to collapse
yes, you have to replace emmc chip on motherboard.
You can try to flash, but as you see and described it points to SDS.