Develop Bugs

[Q] htx one x stuck on splash screen

So I just rooted my phone and tried to install new room cyanogenmod 10 in recovery mode .. after the installation was complete, a simple reboot and after about 10s I could see word cyanogenmod on the screen .. I though it would boot up after a couple of minutes but after 15 mins, still no response .. so i went back into recovery mode and did a factory reset, delete cache and restored the original ROM .. Once again a reboot and it left me with the same booting screen written "cyanogenmod" and nothing else .. I did it once more but no use .. It always gets stuck on the same freaking screen .. Really need help guys ..

whats your hboot ? Did you wipe cache after flashing the boot.img ?

If your hboot is on 1.3x you need a modified hboot for CM10
http://db.tt/uDdWaAtH
And if you want to restore a nandroid you also have to flash the boot.img that is located in the nandroid backup folder

yes did went into the nandroid backup folder and restored it from there .. i had other CleanROM 5.1 zip in the phone memory ..i did a complete reset n tried to install CleanROM 5.1 .. thought may b that could get me out of the loop .. bt didnt help .. doest matter i do nandroid back r unzip clean rom or even cyanogen 10 .. it gets caught up in the same loop hole .. and what is hboot .. ?

You have to flash the boot.img file with fastboot commands from the pc to the phone in the bootloader menu, did you did it like that or did you try to flash it with the recovery ?

no i did it just in the recovery mode .. not from my pc .. do i have to do it from pc .. ? if yes then how.. ?

Do you have fastboot files on the pc ?
---------- Post added at 09:58 AM ---------- Previous post was at 09:55 AM ----------
Check the 9th post from this thread, links to the HTC driver and fastboot files are there. Just follow my post and if you are ready we can go on
http://forum.xda-developers.com/showthread.php?t=2111703

I am sorry but I am a newbie and don't know what an hboot is .. could you tell me what it is .. ? and yes i did wiped the cash when i got stuck in the loophole .. bt it didnt do any good ..

The hboot is like the basic bios of the phone ....
And yes you need a pc to flash the boot.img
Check that post its very clear. Just that one post !!!
And we all where noobs .... i was a űbernoob

Mr Hofs said:
The hboot is like the basic bios of the phone ....
And yes you need a pc to flash the boot.img
Check that post its very clear. Just that one post !!!
And we all where noobs .... i was a űbernoob
Click to expand...
Click to collapse
ok i followed all the steps u told me to .. after entering the three commands on the pc, which were successful, what next .. ? i mean just did those commands on the pc and i have left the cellphone idle i.e still "FASTBOOT USB" .. should i exit it or do a factory wipe and backup .. ?

hassamrehmat said:
ok i followed all the steps u told me to .. after entering the three commands on the pc, which were successful, what next .. ? i mean just did those commands on the pc and i have left the cellphone idle i.e still "FASTBOOT USB" .. should i exit it or do a factory wipe and backup .. ?
Click to expand...
Click to collapse
Go back into recovery and do a full wipe and install the rom. Then reboot and leave it for about 5 minutes

The way to flash a rom is :
Copy the rom.zip to the phones sdcard, open the rom.zip and copy the boot.img file into the fastboot folder on the pc, keep the phone in fastboot usb mode and flash the boot.img
Fastboot erase cache
Fastboot flash boot boot.img
Fastboot erase cache
Then you enter the custom recovery and do a full wipe, after that you flash the rom from inside the recovery

how can i copy the files to one x memory .. it doesnt boot up i.e the pc doesnt show a removable device with storage .. and did the steps u told me to follow n did a factory reset after that .. bt i cant restore bcz the nandroid backup from my cell is removed now .. however i do have it on my pc ..can i install it from there .. ?

hassamrehmat said:
how can i copy the files to one x memory .. it doesnt boot up i.e the pc doesnt show a removable device with storage .. and did the steps u told me to follow n did a factory reset after that .. bt i cant restore bcz the nandroid backup from my cell is removed now .. however i do have it on my pc ..can i install it from there .. ?
Click to expand...
Click to collapse
You can mount the one x as an sdcard inside the recovery, mounts & storage and then the last option at the bottom. Mount as usb disk
Then you can copy the nandroid backup back to the phone and the boot.img to the fastboot folder on the pc. Flash the boot.img, full wipe and restore the nandroid !
Ps what recovery do you have ( also the version number)

Mr Hofs said:
You can mount the one x as an sdcard inside the recovery, mounts & storage and then the last option at the bottom. Mount as usb disk
Then you can copy the nandroid backup back to the phone and the boot.img to the fastboot folder on the pc. Flash the boot.img, full wipe and restore the nandroid !
Ps what recovery do you have ( also the version number)
Click to expand...
Click to collapse
i had jelly bean 4.1.1 firmware 3.14 on my one x .. i rooted it yesterday following onexroot.com which was a success .. then redmondpie mentioned to do a nandroid backup, which i did and also saved files on pc .. then today i tried to flash new rom i.e cyanogenmod and i m stuck ever since .. also the mobile doesnt charge in bootloader mode ..

hassamrehmat said:
i had jelly bean 4.1.1 firmware 3.14 on my one x .. i rooted it yesterday following onexroot.com which was a success .. then redmondpie mentioned to do a nandroid backup, which i did and also saved files on pc .. then today i tried to flash new rom i.e cyanogenmod and i m stuck ever since .. also the mobile doesnt charge in bootloader mode ..
Click to expand...
Click to collapse
What recovery do you have, the phone should charge inside the recovery. Tell me the version you have ?

Hboot-1.33.0000
radio5.1204.162.29

hassamrehmat said:
Hboot-1.33.0000
radio5.1204.162.29
Click to expand...
Click to collapse
I mean the recovery, not the hboot. Enter the recovery and check what version it is

clockworkmod recovery v5.8.1.8

[Q] Noob Help Needed: Phone Stuck

Hi, Brand new Noob here, but hoping someone can help…I’ve had a good scour around and can’t find the answer. We have a Htc one x from orange uk (cid orang001) stuck at “quietly brilliant” screen following an attempt to load ViperX 2.6.0. After downloading, the MAC unzipped the ROM so this was just rezipped back up and transferred over to the SD card, without any special conditions. ( I’ve since read somewhere that this might cause issues)
USB debugger was enabled but its not possible to enable it now.
Fastboot works ok, and we’ve flashed the boot ok, but ADP isn’t working, so it isn’t possible to push the correct ROM.ZIP to the SDcard. CWM is installed.
We’ve seen the post for an updated CWM with ADP enabled on this here but that states its only for at&t models. If we could get ADP working we’d be able to push the correct ROM over, so this would seem the easiest way if possible.
I wanted to avoid doing a RUU in case the phone would end up bricked, but I can’t get the correct version anyway.
Command ./fastboot getvar version-main returns
version-main: 3.16.61.6 and the noob guide at
http://forum.xda-developers.com/showthread.php?t=1859714 says we can’t use a lower version….the nearest RUU I can find is 1.29.061.11 (released on 31/01/2013).
Any ideas on how best to recover this phone? The issue might not be anything to do with the zipping of the ROM, but then I have no idea why its not working…I’m hoping it’s a simple procedure, but I fear it may not be! Please Help!
any help would be much appreciated!!

First of all go and boot into the bootloader, hold down the power button and the volume - button together as long as it takes to get in the bootloader. Do not let go of the buttons before you are in !!!
Check the bootloader, what does it say on top
Probably
Unlocked ?
Endeavouru ?
Hboot : tell me ?
And tell me which recovery you flashed type and version !

Mr Hofs said:
First of all go and boot into the bootloader, hold down the power button and the volume - button together as long as it takes to get in the bootloader. Do not let go of the buttons before you are in !!!
Check the bootloader, what does it say on top
Probably
Unlocked ?
Endeavouru ?
Hboot : tell me ?
And tell me which recovery you flashed type and version !
Click to expand...
Click to collapse
ive got the bootloader unlocked, i did that via htcdev.com
it says... ENDEAVORU PVT SHIP S-ON RL
HBOOT-1.36.0000
i thinks thats what youre looking for

And what recovery ?
You can download the latest JB viper X 3.3.7

Mr Hofs said:
And what recovery ?
You can download the latest JB viper X 3.3.7
Click to expand...
Click to collapse
i running clockworkmod recovery v5.8.2.7
and at yeah, id prefer the jb version of viperx, but i had trouble downloading it

oke do this :
download this recovery https://www.dropbox.com/s/guvfqd7tp8acxg6/recovery 5.8.4.0.img and flash it
then enter the recovery and go to mounts & storage - mount as usb drive (last of the list)
copy the viper x 3.3.7 to the sdcard.
reboot into the bootloader and flash the viper x boot.img (its inside the rom.zip)
go back into the recovery and perform a full wipe
wipe data/factory reset
wipe cache partition
advances->wipe dalvik cache
mounts and storage->format cache,data,system
unhook the usb cable
install the rom.zip and choose in the installer what you like
kernel question ? -> choose Viper X delivered
after install reboot and enjoy the viper rom

Mr Hofs said:
oke do this :
download this recovery https://www.dropbox.com/s/guvfqd7tp8acxg6/recovery 5.8.4.0.img and flash it
then enter the recovery and go to mounts & storage - mount as usb drive (last of the list)
copy the viper x 3.3.7 to the sdcard.
reboot into the bootloader and flash the viper x boot.img (its inside the rom.zip)
go back into the recovery and perform a full wipe
wipe data/factory reset
wipe cache partition
advances->wipe dalvik cache
mounts and storage->format cache,data,system
unhook the usb cable
install the rom.zip and choose in the installer what you like
kernel question ? -> choose Viper X delivered
after install reboot and enjoy the viper rom
Click to expand...
Click to collapse
ive downloaded the vipers.zip file and copied it onto my sdcard but i can't unzip it on my mac to get the boot.img is there something special i need to do with it?

Yeah you need to flash the boot.img just like a recovery....but a different command
Fastboot flash boot boot.img
Check the OP of the viper thread there is a seperate download link for the boot.img file :thumbup:

Mr Hofs said:
Yeah you need to flash the boot.img just like a recovery....but a different command
Fastboot flash boot boot.img
Check the OP of the viper thread there is a seperate download link for the boot.img file :thumbup:
Click to expand...
Click to collapse
im almost there but im stuck at the Kernel Options menu. the screen just isnt responding

Don't know anything about that ..... Tap it real good

Mr Hofs said:
Don't know anything about that ..... Tap it real good
Click to expand...
Click to collapse
thanks a million!!!!!! youre a life saver!!

Its actually a pretty common thing ... Think its related to the touch driver from the installer ....or something like that. I have it too sometimes

HELP - booting problem

(sorry for my english, i'm from Czech)
hello
Yesterday I tried Replaces CM10 but something went wrong and whenever I turn on my mobile it switches on only in ClockworkMod and if I'll click in reboot mobile turn up into ClockworkMod again. Please what should I do?
also it would help if you knew how to reset the boot, I accidentally had set ClockworkMod as a boot.
or if you knew how to get to the storage.
Sorry if it was already there

Whats your hboot number ?
Its stated in the bootloader, its like 1.12 or 1.31, 1.36, 1.39
Lets start with that. And what rom did you want to install ?

Mr Hofs said:
Whats your hboot number ?
Its stated in the bootloader, its like 1.12 or 1.31, 1.36, 1.39
Lets start with that. And what rom did you want to install ?
Click to expand...
Click to collapse
1.39.
i want to install CyanogenMod. but problem is, i don't know how, but i forgot to put the rom to mobile storage. so i write: boot boot.img and when i want to instal it in phone in clockwork I found out that I forgot to put it there.

Download CM10.1 + gapps.zip. enter the recovery and mount the sdcard as usb mass storage device, copy the gapps and the CM10.1 rom to the phone.
Flash the CM10.1 boot.img
Fastboot erase cache
Fastboot flash boot boot.img
Fastboot erase cache
Then enter the recover and perform a FULL wipe ! Then install CM10.1 rom and gapps ....
http://forum.xda-developers.com/showthread.php?t=1786696
http://forum.xda-developers.com/showthread.php?t=2203331

Mr Hofs said:
Download CM10.1 + gapps.zip. enter the recovery and mount the sdcard as usb mass storage device, copy the gapps and the CM10.1 rom to the phone.
Flash the CM10.1 boot.img
Fastboot erase cache
Fastboot flash boot boot.img
Fastboot erase cache
Then enter the recover and perform a FULL wipe ! Then install CM10.1 rom and gapps ....
http://forum.xda-developers.com/showthread.php?t=1786696
http://forum.xda-developers.com/showthread.php?t=2203331
Click to expand...
Click to collapse
i can't mount the SD card because when i click on mount usb storage it write: E: Unable to open ums lunfile (no such file or di...) screen end
what is wrong?

Flash this recovery
http://db.tt/H7m4ffIP
Yours is to old. Flash this one and mount it, then wait 1 minute

Mr Hofs said:
Flash this recovery
*********
Yours is to old. Flash this one and mount it, then wait 1 minute
Click to expand...
Click to collapse
yes that's better, but when i mount sdcard a click on mount usb storage.. phone write usb mass storage but in PC- nothing
Edit:sorry - yes i'm in storage

finish
everything is ok cyanogenmod intalled. thank you soooo much :victory::victory::victory:

Very good !
CASE CLOSED !

HTC One X Bricked.. Help Needed

First of all, I want to tell that I am a beginner and do not know much about rooting and custom ROM installation.
Few days back, I became very keen to know what is custom ROM and is there any custom ROM available for my HTC One X. I searched through internet and found one, downloaded it. Rooted my phone, Unlocked bootloader. After that I installed CWM touch recovery. Everything was going great. Then, I first flashed the kernel given along with that custom ROM. it Flashed. Then, I flashed that Custom ROM. I Showed an error. I flashed it twice or thrice but it stucked on that error. Also in a Hurry, or Excitement, I forgot to take a backup of my previous ROM. After that, I switched on my phone it does nothing and stucked at HTC Bootscreen. I factory reset my phone, it wiped all data from phone. I Thought, a RUU would work, but it also doesn't worked.
I went to HTC Service Center, they are saying that motherboard will be replaced, which is almost of same cost of phone. I cannot spend so much.
I tried so many ways, but nothing worked.
So, I am Finally here seeking help from Experts. Any help will be highly appreciable.
Sorry for my bad English.
Details :
HBoot: 1.73
S-ON
Endevouru

Try this, flash this recovery :
https://www.dropbox.com/s/qp21ubo10xetcvn/Philz recovery 5.15.9.img
Make a full wipe and install the rom.zip. and flash the boot.img from the rom.zip
What rom were you trying to flash ?

If its a kitkat ROM you can't use cwm recovery to flash that rom.. you either use philz recovery given by mr hofs or latest twrp recovery from the twrp thread or indexed listing thread..

a.broken.star said:
If its a kitkat ROM you can't use cwm recovery to flash that rom.. you either use philz recovery given by mr hofs or latest twrp recovery from the twrp thread or indexed listing thread..
Click to expand...
Click to collapse
You mean this one
https://www.dropbox.com/s/14c1ikgsp38axwv/twrp-recovery2.img

Righto...:thumbup:

i was trying to flash MaximusHD rom.
and Philz recovery i have tried already. The problem is I do not have access to storage. All i have is Bootloader access. and nothing on my phone

Charge the battery, unlock the bootloader, flash the custom recovery and install a new rom

Mr Hofs said:
Charge the battery, unlock the bootloader, flash the custom recovery and install a new rom
Click to expand...
Click to collapse
i have tried this too.. no ROM is being flashed. everytime it ends with some error(s)

What error ??? Be more specific otherwise we cant get 1 step ahead
1: Is your bootloader unlocked ?
2: flashes the custom recovery ?
3: what rom ?
4: did you also flashed the boot.img ?
Please answer specifically !

Mr Hofs said:
What error ??? Be more specific otherwise we cant get 1 step ahead
1: Is your bootloader unlocked ?
2: flashes the custom recovery ?
3: what rom ?
4: did you also flashed the boot.img ?
Please answer specifically !
Click to expand...
Click to collapse
1. Bootloader was unlocked, i have relocked it. I'll unlock it. no Issues.
2. I have tried CWM philz touch custom recovery. I'll install it again
3. It do not have any ROM at present. Earlier it had 4.2.2 JB Stock ROM
4. Yes, I flashed boot.img. Nothing worked

1. Unlock the bootloader again
2. Flash the Philz-Recovery
3. Boot the Recovery
4. Install the Rom via ADB-Sideload
5. Reboot to bootloader
6. Flash the Kernel (boot.img)
7. Reboot into system
If you get an error, then post the Code here , so we can find out what's wrong with your phone.
Sent from my HTC One using XDA mobile app

HD2Bastler said:
1. Unlock the bootloader again
2. Flash the Philz-Recovery
3. Boot the Recovery
4. Install the Rom via ADB-Sideload
5. Reboot to bootloader
6. Flash the Kernel (boot.img)
7. Reboot into system
If you get an error, then post the Code here , so we can find out what's wrong with your phone.
Sent from my HTC One using XDA mobile app
Click to expand...
Click to collapse
sorry for this stupid question. But how to use ADB Sideload..??

Just mount the sdcard in the mounts and storage menu ! No need for adb sideload
And don't just install the rom, you must perform a full wipe before that !
Factory reset
Wipe cache partition
Wipe dalvik cache
Format system
Format data
Format cache
Then install the rom !

Mr Hofs said:
Just mount the sdcard in the mounts and storage menu ! No need for adb sideload
And don't just install the rom, you must perform a full wipe before that !
Factory reset
Wipe cache partition
Wipe dalvik cache
Format system
Format data
Format cache
Then install the rom !
Click to expand...
Click to collapse
ok i will try this and will be back with whatevr result comes out....

I bricked mine too , this is what I did
mohitsinghl said:
ok i will try this and will be back with whatevr result comes out....
Click to expand...
Click to collapse
If that doesn't work try this , this is what I did when I bricked my HTC One X:
1. Download Fastboot
2. Download adb
3. Download cm-10.2.1-endeavoru.zip (https://download.cyanogenmod.org/?device=endeavoru)
(I used this one , it's justs so you get your SD Card Working again and you can
put ROMS and everything on it again)
4. Download openrecovery-twrp-2.4.0.0-endeavoru-JB (http://techerrata.com/browse/twrp2/endeavoru)
(This one will be used because it has touch ability's and you can install ROMS with it )
4.1 Or you can download recovery-clockwork-touch-6.0.4.7-endeavoru.img (a.k.a Philz recovery)
(This one will be used because it has touch ability's and you can install ROMS with it )
( I used Philz recovery 5.15.9.img (provided by Mr Hofs -> who is a great guy btw)
5. Download openrecovery-twrp-endeavoru-2.1.7 (http://techerrata.com/browse/twrp2/endeavoru
(This one will be used for adb push commands, openrecovery-twrp-endeavoru-2.1.7 has a built
in ability for your sd-Card , adb can recoginze it but the problem is your touch will not work.)
6. Go into bootloader -> fastboot and do this:
6.1 fastboot flash recovery openrecovery-twrp-endeavoru-2.1.7.img
7. Go into recovery (Hboot -> recovery)
7.1 just open the recovery, your touch will probably not work. DONT LOCK IT JUST LEAVE IT OPEN
(ADB sideload didn't work for me so that's why we are going to do this)
IF YOUR TOUCH WORKS YOU CAN SKIP STEP 8
7.2 do this command: adb devices
If you don't find your devices in this then the next steps will not work.
YOU HAVE TO SEE YOUR DEVICE
7.3 do this command: adb push cm-10.2.1-endeavoru.zip /sdcard/
You can only do cm-10.2.1-endeavoru.zip if the zip file is located in the same folder your using
with command. I'm not sure about /sdcard/ . I cant remember anymore But this will put the
but this will put the zip Directly on your SDcard.
8. Go to bootloader -> fastboot
8.1 do this command: fastboot flash recovery openrecovery-twrp-2.4.0.0-endeavoru-JB.img
8.2 or do this command: fastboot flash recovery Philz recovery 5.15.9.img
Your touch wasn't working but it will work now.
9. Go to booloader -> fastboot
9.1 extract the boot.img from the Download cm-10.2.1-endeavoru.zip into the fastboot folder
9.2 do this command fastboot flash boot boot.img
9.3 fastboot erase cache
10. Go back to recovery
10.1 Wipe User Data
10.2 Wipe data cache
10.3 Go to advanced -> wipe Dalvik Cache
11. Install zip from sdcard
11.1 Choose cm-10.2.1-endeavoru.img
11.2 Install the zip WITH full wipe
12. After the install, reboot. You should have a full functional HTC ONE X now
13. Now but your ROM's(ZIP FILES)/Recovery(ZIP FILES)/Kernels and everything you want on your HTC because
You can see your HTC on your PC again!

I tried adb push.. But i cant find the pushed zip on sd card in recovery.. Moreover i tried flashing using fastboot command i.e. fastboot flash zip rom.zip it ended with an error <remote not allowed>
Sent from my Titanium S5 using XDA Free mobile app

For maximus hd do this :
Flash Philz 5.15 and mount the sdcard and wait literally minutes to let the sdcard pop up, copy the rom, do a full wipe and install it then also flash the boot.img from the maximus rom in the bootloader and reboot the phone
Don't make this so hard on yourself !

Philz 5.15 recovery is not flashed. And ended with an error 0xa . any other way??
Sent from my Titanium S5 using XDA Free mobile app

Uhm really.....second time : post the error/your taken steps ! I'm not playing a game of sharades here ......
If it's not flashed you are doing something wrong

Please don't get angry on me.. M a beginner.
Okey now i have managed to flash philz recovery version 6 i.e. philz touch 6 but still cant get storage popup on my pc. I waited 30 mins after clicking mount /storage/sdcard0
Sent from my Titanium S5 using XDA Free mobile app

Failed to open usb master mode

Failed to open usb master mode
[Preload] Failed to open usb master mode
loading PJ46IMG.zip image...
Failed to open usb master mode
Please plug off USB
btw i unlock my phone
i cant see my htc in pc to copy paste any thing
and i have boot loop
I tried to download the latest HTC Sync Manager, HTC Driver 4.0.1.002, HTC Driver 4.3.0.001 & HTC Driver 3.0.0.007 but still same problem.

That error is because you have the usb cable connected when entering the boot loader. If you want to see the sdcard as a usb diskdrive you can flash a recovery that supports that option like philz touch recovery 5.15 !

thank you for replay Mr Hofs but when im try to recovery i have this error
F:\JDownloader\Fastboot\Fastboot>fastboot flash recovery recovery.img
sending 'recovery' (9190 KB)... OKAY [ 1.090s]
writing 'recovery'... INFOFormat partition SOS done
FAILED (remote: err = 0xa)
finished. total time: 1.323s
btw mt htc one x dosnet have sdcard and my pc cant see my device + that i have boot loop
please help me if can @ skype : shadifares2001 after that u can delete me and block me please its not my device

I don't do skype, but that recovery you are flashing is way to big. They are never bigger than 8 mb on the hox !
https://www.dropbox.com/s/qp21ubo10xetcvn/Philz recovery 5.15.9.img
Try that one !

work fine but still my device in bootloop and my pc cant see htc device to copy and paste inside it
what the next step

You flashed the recovery, so enter it. It doesn't get fixed with only flashing a recovery.
Enter fastboot and select recovery from there. Then enter the mounts and storage menu and tap the last option in that list (mount as usb mass storage) and wait literally a few minutes !

u are super amazing work fine and i see it but all system data gone nothing left ... i copy cm-11-20140525-NIGHTLY-endeavoru and try to install i give me error status 7
installtion aborted
im try to install CyanogenMod

dude thanks for u im almust done i copy the file and enter recovery mode and install from zip and click in cm-11-20140525-NIGHTLY-endeavoru and get this error status 7 installation aborted cyanogenmod i google it they said delete 2 line and i try it but still same

Kitkat based roms need a different recovery. Philz 5.15 is only for NON KITKAT roms.
You want to flash kitkat roms, use this one
https://www.dropbox.com/s/14c1ikgsp38axwv/twrp-recovery2.img

i have this error
no md5 file found
e: unable to mount '/usb-otg
i unlock my htc but i dont think i root it is this matter

No. Just try this. Flash the philz 5.15 again. And copy a sense 5 rom to the phone. Make a FULL wipe in the recovery (that means EVERYTHING you can wipe EXCEPT the sdcard) and install the rom. Don't forget to flash the boot.img from the rom too !
---------- Post added at 05:08 PM ---------- Previous post was at 05:01 PM ----------
And if you want to install CM11 you flash philz and copy the rom to the phone. Then flash the TWRP i linked ya and install the rom with that ! Also flash the correct gapps and also fastboot flash the boot.img from the CM11 zip.
And don't make more threads. Totally unnecessary !

is that driver unable to mount '/usb-otg and how to install it

Why OTG ? If you flash philz 5.15 and copy the rom, then flash TWRP test 2 and install the rom.....you don't need to mount the sdcard in twrp anymore because the rom is already on the sdcard.
What exact steps are you taking now currently ?

man i know im annoying u about this
1- i unlocked my htc no root
2- i install recovey philz touch 5 ( cwm base v : 6.0.3.7)
3- i try to install it give me error status 7

Give me the outcome of :
Fastboot getvar version-main
1: you flash philz 5.15 (which i linked)
2: you copy the rom to the sdcard
3: you make a full wipe
4: you flash the boot.img from the rom in fastboot
5: if it's a kitkat rom you copied you flash the twrp recovery i linked
6: install the rom
7: reboot
* note : if the rom is a sense 5 rom or at least a NON kitkat rom you can stay on philz recovery 5.15 and skip step 5 !
Try this and report what's happening. And with which recovery and such. The more info the better !

Mr Hofs i send my brother mobile to localy expert phone and he cant fix it ........ i dont wanna root i dont wanna kitkat i wanna recovery the orginal system how can u help me about that coz all step u told me to do dont work with me .... be Patient with me help me i can use viper skype and live chat or live voice to connect u to respond fast
thank you

You do this :
Download arhd rom (as good as stock) and copy it to the phones sdcard via philz touch recovery 5.15. Flash the boot.img from the rom via fastboot :
Fastboot flash boot boot.img
Inside recovery you do :
Factory reset
Wipe cache partition
Advanced - wipe dalvik cache
Mounts and storage - format cache, data and system
Then install the rom.zip
Reboot.

can u give me rom link and boot.img link to download it
what this mean
Odexed
MD5: E09540AEFADA9E6FD9E939B05AC3A067
De-Odexed
MD5: 74E4A6D3A129B9727E213B3B41141B40

Take either one. Doesnt matter now

thank you for helping me to fix it i install the original rom and its work fine