[Q] Noob Help Needed: Phone Stuck - HTC One X

Hi, Brand new Noob here, but hoping someone can help…I’ve had a good scour around and can’t find the answer. We have a Htc one x from orange uk (cid orang001) stuck at “quietly brilliant” screen following an attempt to load ViperX 2.6.0. After downloading, the MAC unzipped the ROM so this was just rezipped back up and transferred over to the SD card, without any special conditions. ( I’ve since read somewhere that this might cause issues)
USB debugger was enabled but its not possible to enable it now.
Fastboot works ok, and we’ve flashed the boot ok, but ADP isn’t working, so it isn’t possible to push the correct ROM.ZIP to the SDcard. CWM is installed.
We’ve seen the post for an updated CWM with ADP enabled on this here but that states its only for at&t models. If we could get ADP working we’d be able to push the correct ROM over, so this would seem the easiest way if possible.
I wanted to avoid doing a RUU in case the phone would end up bricked, but I can’t get the correct version anyway.
Command ./fastboot getvar version-main returns
version-main: 3.16.61.6 and the noob guide at
http://forum.xda-developers.com/showthread.php?t=1859714 says we can’t use a lower version….the nearest RUU I can find is 1.29.061.11 (released on 31/01/2013).
Any ideas on how best to recover this phone? The issue might not be anything to do with the zipping of the ROM, but then I have no idea why its not working…I’m hoping it’s a simple procedure, but I fear it may not be! Please Help!
any help would be much appreciated!!

First of all go and boot into the bootloader, hold down the power button and the volume - button together as long as it takes to get in the bootloader. Do not let go of the buttons before you are in !!!
Check the bootloader, what does it say on top
Probably
Unlocked ?
Endeavouru ?
Hboot : tell me ?
And tell me which recovery you flashed type and version !

Mr Hofs said:
First of all go and boot into the bootloader, hold down the power button and the volume - button together as long as it takes to get in the bootloader. Do not let go of the buttons before you are in !!!
Check the bootloader, what does it say on top
Probably
Unlocked ?
Endeavouru ?
Hboot : tell me ?
And tell me which recovery you flashed type and version !
Click to expand...
Click to collapse
ive got the bootloader unlocked, i did that via htcdev.com
it says... ENDEAVORU PVT SHIP S-ON RL
HBOOT-1.36.0000
i thinks thats what youre looking for

And what recovery ?
You can download the latest JB viper X 3.3.7

Mr Hofs said:
And what recovery ?
You can download the latest JB viper X 3.3.7
Click to expand...
Click to collapse
i running clockworkmod recovery v5.8.2.7
and at yeah, id prefer the jb version of viperx, but i had trouble downloading it

oke do this :
download this recovery https://www.dropbox.com/s/guvfqd7tp8acxg6/recovery 5.8.4.0.img and flash it
then enter the recovery and go to mounts & storage - mount as usb drive (last of the list)
copy the viper x 3.3.7 to the sdcard.
reboot into the bootloader and flash the viper x boot.img (its inside the rom.zip)
go back into the recovery and perform a full wipe
wipe data/factory reset
wipe cache partition
advances->wipe dalvik cache
mounts and storage->format cache,data,system
unhook the usb cable
install the rom.zip and choose in the installer what you like
kernel question ? -> choose Viper X delivered
after install reboot and enjoy the viper rom

Mr Hofs said:
oke do this :
download this recovery https://www.dropbox.com/s/guvfqd7tp8acxg6/recovery 5.8.4.0.img and flash it
then enter the recovery and go to mounts & storage - mount as usb drive (last of the list)
copy the viper x 3.3.7 to the sdcard.
reboot into the bootloader and flash the viper x boot.img (its inside the rom.zip)
go back into the recovery and perform a full wipe
wipe data/factory reset
wipe cache partition
advances->wipe dalvik cache
mounts and storage->format cache,data,system
unhook the usb cable
install the rom.zip and choose in the installer what you like
kernel question ? -> choose Viper X delivered
after install reboot and enjoy the viper rom
Click to expand...
Click to collapse
ive downloaded the vipers.zip file and copied it onto my sdcard but i can't unzip it on my mac to get the boot.img is there something special i need to do with it?

Yeah you need to flash the boot.img just like a recovery....but a different command
Fastboot flash boot boot.img
Check the OP of the viper thread there is a seperate download link for the boot.img file :thumbup:

Mr Hofs said:
Yeah you need to flash the boot.img just like a recovery....but a different command
Fastboot flash boot boot.img
Check the OP of the viper thread there is a seperate download link for the boot.img file :thumbup:
Click to expand...
Click to collapse
im almost there but im stuck at the Kernel Options menu. the screen just isnt responding

Don't know anything about that ..... Tap it real good

Mr Hofs said:
Don't know anything about that ..... Tap it real good
Click to expand...
Click to collapse
thanks a million!!!!!! youre a life saver!!

Its actually a pretty common thing ... Think its related to the touch driver from the installer ....or something like that. I have it too sometimes

Related

[Q] HELP!

Help!
I have studied the forum and have come close to trying to fix my problem but the bravery to actually act on my thoughts has escaped me at the moment!
I have got an HTC One X which I got 2nd hand, it has the following:
Android 4.1.1
HTC Sense 4+
Software Number InsertCoin One X 17.1.0
Kernel version 3.1.10-g03b5369 (If that makes any sense)
When I do the power button and the down button I get the following:
UNLOCKED
S-ON
HBOOT 1.39.0000
It also has Clockwork Recovery on it - V6.0.2.7
Its unlocked but it looks like it came from 3 UK originally.
The CID is H3G___001
3.14.771.34
All I really want to do is either take it back to stock or put a custom rom on it with good battery life and all the Sense widgets which this one does not have. I understand doing that may blow the battery life though.
It looks like if I want to use the Nandroid back up I need TWRP backup installed for the image file but I dont have that and dont really know how to get it.
Just need some help in what to do and the steps to take to do what I want.
As I say I have searched and got this far but not brave enough to move on.
Many thanks
Trying a different rom with a custom kernel would be the easiest solution !
Lets start with downloading this Rom
http://forum.xda-developers.com/showthread.php?t=2027029
Steps :
1: copy the rom.zip to the sdcard
2: copy the boot.img file from the rom.zip to the fastboot folder on the pc
3: put the phone in the bootloader and flash the boot.img
Fastboot erase cache
Fastboot flash boot boot.img
Fastboot erase cache
4: unhook the usb cable and enter the recovery
5: perform a full wipe
Factory reset
Wipe cache partition
Advanced - wipe dalvik cache
Mounts & storage - format cache, data, system
Then install the new rom.zip
Install zip from sdcard
Choose zip from sdcard
Navigate to the blade rom.zip and install it.
Edit: ninja'd
Mr Hofs said:
Trying a different rom with a custom kernel would be the easiest solution !
Lets start with downloading this Rom
http://forum.xda-developers.com/showthread.php?t=2027029
Steps :
Click to expand...
Click to collapse
Thank you for the fast response - Is the SDcard actually the phone storage so the large amount of space I have (around 25gb)?
Yes sir, correct
Mr Hofs
Thank you very much!
Worked like a dream
simonsteele said:
Mr Hofs
Thank you very much!
Worked like a dream
Click to expand...
Click to collapse
Good ! Hopefully you will have better battery life .....
For now ... (leaving this half open )
CASE CLOSED !

HELP - booting problem

(sorry for my english, i'm from Czech)
hello
Yesterday I tried Replaces CM10 but something went wrong and whenever I turn on my mobile it switches on only in ClockworkMod and if I'll click in reboot mobile turn up into ClockworkMod again. Please what should I do?
also it would help if you knew how to reset the boot, I accidentally had set ClockworkMod as a boot.
or if you knew how to get to the storage.
Sorry if it was already there
Whats your hboot number ?
Its stated in the bootloader, its like 1.12 or 1.31, 1.36, 1.39
Lets start with that. And what rom did you want to install ?
Mr Hofs said:
Whats your hboot number ?
Its stated in the bootloader, its like 1.12 or 1.31, 1.36, 1.39
Lets start with that. And what rom did you want to install ?
Click to expand...
Click to collapse
1.39.
i want to install CyanogenMod. but problem is, i don't know how, but i forgot to put the rom to mobile storage. so i write: boot boot.img and when i want to instal it in phone in clockwork I found out that I forgot to put it there.
Download CM10.1 + gapps.zip. enter the recovery and mount the sdcard as usb mass storage device, copy the gapps and the CM10.1 rom to the phone.
Flash the CM10.1 boot.img
Fastboot erase cache
Fastboot flash boot boot.img
Fastboot erase cache
Then enter the recover and perform a FULL wipe ! Then install CM10.1 rom and gapps ....
http://forum.xda-developers.com/showthread.php?t=1786696
http://forum.xda-developers.com/showthread.php?t=2203331
Mr Hofs said:
Download CM10.1 + gapps.zip. enter the recovery and mount the sdcard as usb mass storage device, copy the gapps and the CM10.1 rom to the phone.
Flash the CM10.1 boot.img
Fastboot erase cache
Fastboot flash boot boot.img
Fastboot erase cache
Then enter the recover and perform a FULL wipe ! Then install CM10.1 rom and gapps ....
http://forum.xda-developers.com/showthread.php?t=1786696
http://forum.xda-developers.com/showthread.php?t=2203331
Click to expand...
Click to collapse
i can't mount the SD card because when i click on mount usb storage it write: E: Unable to open ums lunfile (no such file or di...) screen end
what is wrong?
Flash this recovery
http://db.tt/H7m4ffIP
Yours is to old. Flash this one and mount it, then wait 1 minute
Mr Hofs said:
Flash this recovery
*********
Yours is to old. Flash this one and mount it, then wait 1 minute
Click to expand...
Click to collapse
yes that's better, but when i mount sdcard a click on mount usb storage.. phone write usb mass storage but in PC- nothing
Edit:sorry - yes i'm in storage
finish
everything is ok cyanogenmod intalled. thank you soooo much :victory::victory::victory:
Very good !
CASE CLOSED !

[Q] HELP! Cant flash Roms

Help my hox is lock on sentinel 4.75 and I cant flash any other rom onto it.
Every time I try to load another rom it crashed at the htc boot screen and never load (I have left it for up to 20 mins)
When this happens the only thing I can do is reload a nandroid of sentinel 4.75 and flash the boot image to return to my previous rom.
I have tried multiple roms including probam, sentinel 5.0, xenonhd and icj with no luck on any of them.
I am on Hboot 1.31 and have installed philz recovery.
Recently I found that my phone had no root access and had to reflash the rom - again the only one that worked was sentinel 4.75
Is there anything I can do to fix my phone to allow me to load another rom. Im finding different issues every time I reload sentinel and would really love to load something else.
Update the hboot
I am guessing that you are forgetting to flash the boot image included in the rom you desire to install.
For example you want to install sentinel v5.00.
update: forgot to mention that you need to update your hboot to run newer roms. you can find proper
hboot update files for your cid in xda forum. Credits to Mr Hofs for the reminder.
Follow these steps.
Technical terms:
adb or fastboot folder: a folder where you have fastboot.exe and adb.exe
HOX: HTC One X
preparation:
a. go to your fastboot or adb folder and rename any 'boot.img' to anything else, like sentinel475.img
b. download the zip file of the rom you want to install
c. copy this zip file into your HOX
d. open the zip file and copy the 'boot.img' file into your adb or fastboot folder
e. make sure your HOX has atleast 60% charge(50% is also fine)
Flashing procedure:
Reboot into recovery
Select 'wipe data/factory reset'
Select 'wipe data/factory reset for new rom' ( applicable to philz recovery only)
Then go back to main menu in recovery
Select 'install zip from sdcard'
Select the zip file, the one you copied to your HOX
Once it has been flashed properly
Reboot into bootloader
connect your HOX with your PC and make sure the HOX display shows 'fastboot usb' in red
open a command window and go to your fastboot folder
type in fastboot flash boot boot.img
type in fastboot erase cache
type in fastboot reboot
disconnect your hox and wait for 5 to 7 minutes for hox to boot into desktop
Thats it. I always follow these steps and everything is fine. You also have to flash gapps zip file but we need to get a proper rom
loaded first before we can do anything else. gapps is always flashable later so no worries about it.
BTW, does it say 'Unlocked' or 'Relocked' in your bootload on the top of the screen?
Can you post the steps you are following to flash other roms? May be you are missing some steps.
Most of the times, a rom will not boot if you don't flash the boot.img that came with the rom.
Thanks, and let me know your results
[Disclaimer: If you follow these steps then you automatically agree to not hold me and all xda forum staff and members responsible for
any damage that might have resulted following or not following these instructions properly or improperly.]
Leave the steps above for now. First give me the outcome of
Fastboot getvar version-main
Thanks rowlf I have installed a few roms before and am familiar with the installation process.
Sorry mistaken it is hboot 1.36
Mr hofs - the version is 3.14.707.24
In case you need cid is HTC__044
I suggest you run the ruu to get back to full stock and try to update via official ota.
http://www.androidruu.com/getdownlo...Radio_5.1204.162.29_release_296434_signed.exe
Get the hboot higher up.
Edit :
1.36 ? Thats fine for all roms. When you install a new one i always advice to do the full wipe manually. Factory reset, wipe caches and format cache,data and system ! Then install the rom.

[Q] urgent help needed plz.. i hooked up my phn

I am a noob for the noob in this field... i am trying to learn quite a bit.... i have tried to get back to stock sense5.0 on my HOX after using CM10.2 (cid : htc_038) (hboot : 1.73.0000 ; relocked ) i used CWM recovery 5.8.4.0 ... i dont what i did wrong but my phn just went into a boot loop (just showing hTc logo ) i again flashed CWM recovery from then my usb mount is not working ...
so wt i just need now is ..
1. just how to mount my usb ...
2.how to get my stock sense 5 ...
i already erased everything in my sd nd internal too... i erased cache before the first attempt also,....
i reffered countless threads but none of them worked for me... please friends some one take a little time in replying me... am in a very bad state r8 now....
PS : touch does not work in my recovery so TWRP is useless to me... :crying: it says slide to unlock
anything now... let it be sense or CM ... i just want my phn to turn on... :crying:
Aditya chinta said:
(cid : htc_038) (hboot : 1.73.0000 ; relocked )
Click to expand...
Click to collapse
One thing, UNLOCK YOUR BOOTLOADER then flash a custom recovery and a custom ROM.
1: unlock bootloader
2: get your main version number :
Fastboot getvar version-main
Take that number and go here
http://forum.xda-developers.com/showthread.php?t=1975140
3: Download the matching nandroid backup and flash the boot.img and recovery.img
4: enter the recovery and copy the nand to the sdcard by enabling mass storage
5: make a full wipe in the recovery and restore the nandroid backup
6: reboot
If the recovery from the nandroid does not give you ums acces then flash this recovery first
https://www.dropbox.com/s/yqzlpqo8illa53j/Philz recovery 5.15.9.img
Enter it and enable mass storage, wait literally for a few minutes to let it pop up. Then copy the nand. And start over at point 3 !
Cheers
usb mount not working
Mr Hofs said:
1: unlock bootloader
2: get your main version number :
Fastboot getvar version-main
Take that number and go here
http://forum.xda-developers.com/showthread.php?t=1975140
3: Download the matching nandroid backup and flash the boot.img and recovery.img
4: enter the recovery and copy the nand to the sdcard by enabling mass storage
5: make a full wipe in the recovery and restore the nandroid backup
6: reboot
If the recovery from the nandroid does not give you ums acces then flash this recovery first
https://www.dropbox.com/s/yqzlpqo8illa53j/Philz recovery 5.15.9.img
Enter it and enable mass storage, wait literally for a few minutes to let it pop up. Then copy the nand. And start over at point 3 !
Cheers
Click to expand...
Click to collapse
thats is the main problem sir ... i am not able to acces the mass storage... i can not copy the rom from my pc to the storage...
i had the rom in the first attempt but after formatting i lost that.. now not able to detect the storage to my pc ...
Did you flash philz 5.15 and enabled it in the mounts and storage menu (bottom option in that menu) and waited for minutes ?
no sir...
Mr Hofs said:
Did you flash philz 5.15 and enabled it in the mounts and storage menu (bottom option in that menu) and waited for minutes ?
Click to expand...
Click to collapse
am so sorry for being soo noob... actually i dont even know wt that actually is...
I gave you the dropbox link to the recovery, download it and flash it !
Rename the file to recovery.img and flash it with these commands
Fastboot flash recovery recovery.img
Fastboot erase cache
But first unlock the bootloader again !
Then proceed
thanks u sir.. my phn is on now..
thanks for the replies bro... i dont know wt i did but my phn is on now..
but one thing ..
my getvar main version is 4.19.720.1 ,... cid htc_038 ... but it is not given in the collection.. is it alright to install any of the nand with cid htc _038 ??
Ah no I see that the 3.14 is available but that one does not work (touch screen will not respond) so i suggest to flash a sense 5 custom rom
:crying::crying::crying:
Mr Hofs said:
Ah no I see that the 3.14 is available but that one does not work (touch screen will not respond) so i suggest to flash a sense 5 custom rom
Click to expand...
Click to collapse
ok then .. i may adjust with cm 10.2 or revolution sense 5
Your choice

HTC One X Bricked.. Help Needed

First of all, I want to tell that I am a beginner and do not know much about rooting and custom ROM installation.
Few days back, I became very keen to know what is custom ROM and is there any custom ROM available for my HTC One X. I searched through internet and found one, downloaded it. Rooted my phone, Unlocked bootloader. After that I installed CWM touch recovery. Everything was going great. Then, I first flashed the kernel given along with that custom ROM. it Flashed. Then, I flashed that Custom ROM. I Showed an error. I flashed it twice or thrice but it stucked on that error. Also in a Hurry, or Excitement, I forgot to take a backup of my previous ROM. After that, I switched on my phone it does nothing and stucked at HTC Bootscreen. I factory reset my phone, it wiped all data from phone. I Thought, a RUU would work, but it also doesn't worked.
I went to HTC Service Center, they are saying that motherboard will be replaced, which is almost of same cost of phone. I cannot spend so much.
I tried so many ways, but nothing worked.
So, I am Finally here seeking help from Experts. Any help will be highly appreciable.
Sorry for my bad English.
Details :
HBoot: 1.73
S-ON
Endevouru
Try this, flash this recovery :
https://www.dropbox.com/s/qp21ubo10xetcvn/Philz recovery 5.15.9.img
Make a full wipe and install the rom.zip. and flash the boot.img from the rom.zip
What rom were you trying to flash ?
If its a kitkat ROM you can't use cwm recovery to flash that rom.. you either use philz recovery given by mr hofs or latest twrp recovery from the twrp thread or indexed listing thread..
a.broken.star said:
If its a kitkat ROM you can't use cwm recovery to flash that rom.. you either use philz recovery given by mr hofs or latest twrp recovery from the twrp thread or indexed listing thread..
Click to expand...
Click to collapse
You mean this one
https://www.dropbox.com/s/14c1ikgsp38axwv/twrp-recovery2.img
Righto...:thumbup:
i was trying to flash MaximusHD rom.
and Philz recovery i have tried already. The problem is I do not have access to storage. All i have is Bootloader access. and nothing on my phone
Charge the battery, unlock the bootloader, flash the custom recovery and install a new rom
Mr Hofs said:
Charge the battery, unlock the bootloader, flash the custom recovery and install a new rom
Click to expand...
Click to collapse
i have tried this too.. no ROM is being flashed. everytime it ends with some error(s)
What error ??? Be more specific otherwise we cant get 1 step ahead
1: Is your bootloader unlocked ?
2: flashes the custom recovery ?
3: what rom ?
4: did you also flashed the boot.img ?
Please answer specifically !
Mr Hofs said:
What error ??? Be more specific otherwise we cant get 1 step ahead
1: Is your bootloader unlocked ?
2: flashes the custom recovery ?
3: what rom ?
4: did you also flashed the boot.img ?
Please answer specifically !
Click to expand...
Click to collapse
1. Bootloader was unlocked, i have relocked it. I'll unlock it. no Issues.
2. I have tried CWM philz touch custom recovery. I'll install it again
3. It do not have any ROM at present. Earlier it had 4.2.2 JB Stock ROM
4. Yes, I flashed boot.img. Nothing worked
1. Unlock the bootloader again
2. Flash the Philz-Recovery
3. Boot the Recovery
4. Install the Rom via ADB-Sideload
5. Reboot to bootloader
6. Flash the Kernel (boot.img)
7. Reboot into system
If you get an error, then post the Code here , so we can find out what's wrong with your phone.
Sent from my HTC One using XDA mobile app
HD2Bastler said:
1. Unlock the bootloader again
2. Flash the Philz-Recovery
3. Boot the Recovery
4. Install the Rom via ADB-Sideload
5. Reboot to bootloader
6. Flash the Kernel (boot.img)
7. Reboot into system
If you get an error, then post the Code here , so we can find out what's wrong with your phone.
Sent from my HTC One using XDA mobile app
Click to expand...
Click to collapse
sorry for this stupid question. But how to use ADB Sideload..??
Just mount the sdcard in the mounts and storage menu ! No need for adb sideload
And don't just install the rom, you must perform a full wipe before that !
Factory reset
Wipe cache partition
Wipe dalvik cache
Format system
Format data
Format cache
Then install the rom !
Mr Hofs said:
Just mount the sdcard in the mounts and storage menu ! No need for adb sideload
And don't just install the rom, you must perform a full wipe before that !
Factory reset
Wipe cache partition
Wipe dalvik cache
Format system
Format data
Format cache
Then install the rom !
Click to expand...
Click to collapse
ok i will try this and will be back with whatevr result comes out....
I bricked mine too , this is what I did
mohitsinghl said:
ok i will try this and will be back with whatevr result comes out....
Click to expand...
Click to collapse
If that doesn't work try this , this is what I did when I bricked my HTC One X:
1. Download Fastboot
2. Download adb
3. Download cm-10.2.1-endeavoru.zip (https://download.cyanogenmod.org/?device=endeavoru)
(I used this one , it's justs so you get your SD Card Working again and you can
put ROMS and everything on it again)
4. Download openrecovery-twrp-2.4.0.0-endeavoru-JB (http://techerrata.com/browse/twrp2/endeavoru)
(This one will be used because it has touch ability's and you can install ROMS with it )
4.1 Or you can download recovery-clockwork-touch-6.0.4.7-endeavoru.img (a.k.a Philz recovery)
(This one will be used because it has touch ability's and you can install ROMS with it )
( I used Philz recovery 5.15.9.img (provided by Mr Hofs -> who is a great guy btw)
5. Download openrecovery-twrp-endeavoru-2.1.7 (http://techerrata.com/browse/twrp2/endeavoru
(This one will be used for adb push commands, openrecovery-twrp-endeavoru-2.1.7 has a built
in ability for your sd-Card , adb can recoginze it but the problem is your touch will not work.)
6. Go into bootloader -> fastboot and do this:
6.1 fastboot flash recovery openrecovery-twrp-endeavoru-2.1.7.img
7. Go into recovery (Hboot -> recovery)
7.1 just open the recovery, your touch will probably not work. DONT LOCK IT JUST LEAVE IT OPEN
(ADB sideload didn't work for me so that's why we are going to do this)
IF YOUR TOUCH WORKS YOU CAN SKIP STEP 8
7.2 do this command: adb devices
If you don't find your devices in this then the next steps will not work.
YOU HAVE TO SEE YOUR DEVICE
7.3 do this command: adb push cm-10.2.1-endeavoru.zip /sdcard/
You can only do cm-10.2.1-endeavoru.zip if the zip file is located in the same folder your using
with command. I'm not sure about /sdcard/ . I cant remember anymore But this will put the
but this will put the zip Directly on your SDcard.
8. Go to bootloader -> fastboot
8.1 do this command: fastboot flash recovery openrecovery-twrp-2.4.0.0-endeavoru-JB.img
8.2 or do this command: fastboot flash recovery Philz recovery 5.15.9.img
Your touch wasn't working but it will work now.
9. Go to booloader -> fastboot
9.1 extract the boot.img from the Download cm-10.2.1-endeavoru.zip into the fastboot folder
9.2 do this command fastboot flash boot boot.img
9.3 fastboot erase cache
10. Go back to recovery
10.1 Wipe User Data
10.2 Wipe data cache
10.3 Go to advanced -> wipe Dalvik Cache
11. Install zip from sdcard
11.1 Choose cm-10.2.1-endeavoru.img
11.2 Install the zip WITH full wipe
12. After the install, reboot. You should have a full functional HTC ONE X now
13. Now but your ROM's(ZIP FILES)/Recovery(ZIP FILES)/Kernels and everything you want on your HTC because
You can see your HTC on your PC again!
I tried adb push.. But i cant find the pushed zip on sd card in recovery.. Moreover i tried flashing using fastboot command i.e. fastboot flash zip rom.zip it ended with an error <remote not allowed>
Sent from my Titanium S5 using XDA Free mobile app
For maximus hd do this :
Flash Philz 5.15 and mount the sdcard and wait literally minutes to let the sdcard pop up, copy the rom, do a full wipe and install it then also flash the boot.img from the maximus rom in the bootloader and reboot the phone
Don't make this so hard on yourself !
Philz 5.15 recovery is not flashed. And ended with an error 0xa . any other way??
Sent from my Titanium S5 using XDA Free mobile app
Uhm really.....second time : post the error/your taken steps ! I'm not playing a game of sharades here ......
If it's not flashed you are doing something wrong
Please don't get angry on me.. M a beginner.
Okey now i have managed to flash philz recovery version 6 i.e. philz touch 6 but still cant get storage popup on my pc. I waited 30 mins after clicking mount /storage/sdcard0
Sent from my Titanium S5 using XDA Free mobile app

Categories

Resources