Hi. Sorry for my English.
I had problem on my SM-605 with S-Pen dock. On an every tablet vibration, the tablet said that the pen is out (while it is in).
I opened the tablet and noted that the T-shaped rotary button that is responsible for S-Pen In or Out is very short, so, when S-Pen is in, it is between On and Off, so every vibration swithes it.
I fixed it:
I took some Gel glue (is is called 'Moment' / "Момент" in Russia) and put some at the end of the T-shaped button. It was hardening for 24 hours (with tablet's back opened and camera module covered to protect from dust). Then I've assembled all back. Now I have to put S-Pen out for 2mm to make sensor switched.
Some photos (sorry, newbies unable to post pictures or links)
The problem: Stilus is in, but the buton is not pressed. It's original shape of the button, it is a little bit bended to right (or possibly it is bad button and originally it is planned to be straight?)
https:??www dropbox com?s?gbrpv1isup3vwa8?2014-01-21%2000.31.50.jpg
The glue gel is fresh, not hardened yet
https:??www dropbox com?s?u0eg6uqqfpgpwju?2014-01-21%2001.15.01.jpg
https:??www dropbox com?s?ywruv84wtf582k0?2014-01-21%2001.15.22.jpg
PS> BTW, back cover is GLUED to the case. Click-locks are deep, about 2cm from the edge. So open carefully. The cover can be bended quiet well without breaking it.
PPS> Alternatively, you can glue some tape at the end of the S-Pen (on the round part of it), but be careful not to detach the tape and leave it inside while putting S-Pen in\out.
filimonic said:
Hi. Sorry for my English.
I had problem on my SM-605 with S-Pen dock. On an every tablet vibration, the tablet said that the pen is out (while it is in).
I opened the tablet and noted that the T-shaped rotary button that is responsible for S-Pen In or Out is very short, so, when S-Pen is in, it is between On and Off, so every vibration swithes it.
I fixed it:
I took some Gel glue (is is called 'Moment' / "Момент" in Russia) and put some at the end of the T-shaped button. It was hardening for 24 hours (with tablet's back opened and camera module covered to protect from dust). Then I've assembled all back. Now I have to put S-Pen out for 2mm to make sensor switched.
Some photos (sorry, newbies unable to post pictures or links)
The problem: Stilus is in, but the buton is not pressed. It's original shape of the button, it is a little bit bended to right (or possibly it is bad button and originally it is planned to be straight?)
https:??www dropbox com?s?gbrpv1isup3vwa8?2014-01-21%2000.31.50.jpg
The glue gel is fresh, not hardened yet
https:??www dropbox com?s?u0eg6uqqfpgpwju?2014-01-21%2001.15.01.jpg
https:??www dropbox com?s?ywruv84wtf582k0?2014-01-21%2001.15.22.jpg
PS> BTW, back cover is GLUED to the case. Click-locks are deep, about 2cm from the edge. So open carefully. The cover can be bended quiet well without breaking it.
PPS> Alternatively, you can glue some tape at the end of the S-Pen (on the round part of it), but be careful not to detach the tape and leave it inside while putting S-Pen in\out.
Click to expand...
Click to collapse
Yeah i had problem same with you. I just sealed with thin layer on grip of s pen. And then problem solven. I like this this tablet but little bit problem like this make all of goothings look badly. But thanks for your tips.
Related
Hey guys. I have the Telus HTC Touch Pro2, and I have noticed a problem. The part where the touch screen half of the phone makes contact with the keyboard part, causes a scratch on the keyboard part. There was plastic on this part before, but I removed it, and now it is scratching. I don't mind this, but just wanted to warn ppl not to remove the plastic.
I will post pics tomorrow.
I had a little piece of plastic just on the right side of the keyboard. I removed this, because I tought I missed it with unpacking my TP2. But now there is a little woggle(? mean little space between screen and keyboard), so everytime I press the screen on that side of the device I can feel and hear the two parts coming together. It's really annoing and it started when I removed the little piece of plastic. For my feeling it's a last fast hot fix by HTC.
But i don't see scratshes yet. I can see dirt on the left and right of the keyboard where the sliding is, but I can easily remove this. But on the longer term, I think there will be permanent 'dirt' aka scratches on both sites....but hey, when you don't want this to happen, put your device away and don't use it
Scratches fix.
As soon as i opened my TP2, i knew the clear plastics were for protection so i left them. In time the one on the right started to peel itself off. THE FIX... I removed it completely and colored it BLACK with a Sharpie Marker, pulled out some transparent scotch tape out of my drawer and carefully traced/cut it out with a sharp razorblade. Carefully stuck it back on and VOILA! A perfectly new replacement a-la' Jerry Rig! Maybe you can cut out 2 pieces ontop of one another to reduce the play when closed? Time = Approx. 10mins.
Hey guys. Yea I just wanted to leave this as a warning to other tp2 owners who thought the plastic was just packaging.
I can't take any pictures since the only other camera is a phone. It dosen't capture the scratches properly.
I left the stickers on. However, as it turned out later, one of the stickers wasn't applied properly. Eventually, the sliding motion caused that sticker to come off and bend just a little at one corner. I cut the bent part off, and the whole thing came of a few days later.
When you get your phone, make sure those stickers are applied properly, and squeeze out air bubble from underneath if needed.
http://forum.xda-developers.com/showthread.php?t=555752
I was experiencing random screen shutoffs after fitting my galaxy note 10.1 (2014) for a new case.
It took a while before I finally realized that the random shut offs were being triggered by the case, more specifically, when the edge of my case came in line with the edge of the tablet, which is an awesome feature when you have the cover covering the front of the unit.
But the problem is it manages to shut off screen regardless of which side of the unit the cover is on, as long as the edge of the cover is aligned with the units edge. This can be quite frustrating when trying to read while holding the tablet in certain orientations.
Questions: I was wondering if anyone else has experienced similar issues with their cases/covers (a little research seems to indicate this is not an isolated issue and many, if not all, cases/covers suffer from this issue).
1) If you have not, which cases/covers do you use? Do these cases resolve the issue by never aligning the cover to the same position when flipped backwards as when flipped forwards (i.e. skewed slightly short of the edge when in backwards position)?
2) If you have experienced this issue, how have you addressed it? Can you disable the magnetic sensor?
3) Would weakening the magnet in the case perhaps ensure that it was only sensed in the forward position?
SKida00 said:
I was experiencing random screen sback andk ffs after fitting my galaxy note 10.1 (2014) for a new case.
It took a while before I finally realized that the random shut offs were being triggered by the case, more specifically, when the edge of my case came in line with the edge of the tablet, which is an awesome feature when you have the cover covering the front of the unit.
But the problem is it manages to shut off screen regardless of which side of the unit the cover is on, as long as the edge of the cover is aligned with the units edge. This can be quite frustrating when trying to read while holding the tablet in certain orientations.
et in the case perhaps ensure that it was only sensed in the forward position?
Click to expand...
Click to collapse
yes i have the same problem. pick up A generic folio type case for my P600. Case looks and feels great. Auto wake works brilliantly when I open the cover, but there is the problem of The screen turning off when I flip the cover over to the back and the magnetic edges meet. Dunno how to fix this yet. Tried the magnetoff xposed module but that doesn't seem to work.
I got the Moko slim case and the same thing happens, what I did to circumvent the problem was to put my screen cleaning cloth between the case and the tablet. This prevents the magnet from locking the screen when completely folded backwards, the only thing is that this method will block the camera with the cloth. For me this is not a problem I don't see myself using the camera on my tablet when I can use my SGS3's camera, and this way I never forget my screen cleaning cloth .
I've read about this on other devices on various covers as well. they think it mah be due to the magnet not being properly shielded. dunno any fixes other than get another case.
I hade a cover for my old Ipad and it all so turn off the Ipad when I flipped over the cover.
It did turn out the problem was with the magnet and after getting a new one, the problem was solved.
My poetic slimline work perfectly no issues at all. Love the look and feel, I do want a carry slevee tho for more protection if I wanna bring it out of the house. Or even just to store in the house. But overall love this case.
Sent from my SM-P600 using Tapatalk
Get a piece of sheet metal (strip out a cheapie magnetic whiteboard , a few dollars at a variety store) cut to just less than the back of the tablet screen.
Cover it with a thin plastic film (to safeguard from cutting yourself)
It will adhere to the back of the screen magnetically and flatten the magnet's field
Now you can use the device with the keyboard tucked away behind the screen. (you may have to leave a small air gap say 5mm to 10 mm)
This does not affect the normal screen-keyboard functions when used conventionally
Same problem with Galaxy Tab A (Nougat)
There is an option in the tab to turn it off, but regardless what you choose, the tablet still responds to the magnet. Very annoying when you lay down your tablet flat. For now i just put something between the cover and the back of the tablet, like a handkerchief. This works for me, but ofcourse it's not a solution just a workaround. I'm still trying to find a solution.
Did you find any way to turn off the magnetic lock and unlock function? When I backfold my cover (aftermarket), it automatically locks my tab. Which is very irritating. I have Samsung galaxy tab S5e
There wasn't a good search result on a way to disable it via software or hardware mod so I thought I would post the solution I just did on my daughter's new tablet folio.
She has an old S3 Tab so the options are quite limited so figured modification was the only way. I ended up removing 3 magnets until I figured out which one actually did the on/off Hall effect. The smart thing to do would have been to use a magnet to find where on the tablet the Hall effect sensor was first, then remove just that magnet. The other magnets are for holding the clasp in place when the folio is open or closed.
I just cut an X over the magnet location, removed it, then filled it back in with hot glue. On her tablet, the Hall sensor was on the top left (fat arrow). It's annoying to have to do this but there's no other way. I tried the metal plate trick but that looked pretty bad and didn't always work.
Hope that helps someone
Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
pulesky said:
Hi all,
i'm very disappointed because i'm just breaking my screen when my zenfone fall of 60cm.
LCD is ok but screen is dead
On ebay i know you can find only the screen with kit, and LCD + screen
Does any one have advice for replacing the screen or screen + lcd? (video or pictures).
Asus France ask me 180€ to change that
thank for your help...
Click to expand...
Click to collapse
Seems pretty easy, please check these videos:
https://www.youtube.com/watch?v=qMIivqu6XJY
https://www.youtube.com/watch?v=v4HZt3Aadsc
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
dodongobongo said:
I ordered a screen replacement on AliExpress. I've only cracked the glass on my phone, but I don't think it's possible to replace the glass on its own. (Unless you have the hands of a neurosurgeon and special equipment.)
Tried changing screen today, but it requires a complete disassemble of the unit. I managed to remove the back and disconnect the components, however I wasn't able to remove the battery since it seems to be glued (?) in place on one side. I even tried using quite a bit of force, but eventually I chickened out since the battery started bending. I have no idea how they do it so easily in the video. If anyone here has managed this disassemble I'd be very interested in getting some details.
Click to expand...
Click to collapse
Try using a hair dryer on the battery for a minute, but keep moving the hair dryer up and down, to spread the heat all over, this should make the glue soft enough to make it easier to peel the battery off.
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
dodongobongo said:
Finally managed to replace the screen. This one was really difficult to repair compared to the previous phones I've worked on, but maybe in part because there are no complete instructions out there yet. Lots of glue and tape holding it all together.
The battery isn't really glued, but rather held down by some sticky plastic. (Kinda like chewing gum.) I don't think heating will help here. I used a long, flat plastic object to reach underneath and loosen it from the battery.
I forgot to take pictures, but here are the steps I took. You can find some photos for the first half of the procedure.
Remove 14 screws from the back cover
Carefully remove back plastic cover (double sided tape on center)
Unplug the three connectors going to the top PCB/SoC (these are screen, SIM/SD and battery)
Remove speaker (black piece at the bottom, nothing is holding it in place)
Remove bottom PCB: flip up the little black switch to loosen the connector cable next to the battery, then unplug the wire going to the top PCB, then you can remove it. Vibrator piece doesn't need to be unplugged.
Battery can now be removed, but is as mentioned fastened very well. Try to pull it up on the left side to reach under it.
Unplug digitizer connector on the left side of the top PCB. Just peel off the yellow take and pull it out.
Peel loose the part of the metallic shielding that fastened the top PCB to the surface under where the battery was.
Top PCB can now be removed, start from right side.
Peel off the little "sticker" the digitizer connector goes to. This is probably part of what you're replacing, so it doesn't matter if you destroy it in the process. Otherwise try heating it.
Screen can finally be removed. It's removed from the front of the phone, same as for Zenfone 5. Start at the bottom. It's fastened with glue along all sides. If you're hoping not to ruin the LCD while removing the screen you will probably need a heat gun and extreme patience.
Click to expand...
Click to collapse
Just cracked my phone. :crying:Thanks for the instructions. Before I decide to do this, are any of the adhesives necessary to put the phone back together?
Yes, order some double-tape for cellphones.
Glad I'm not the only one that succeded althought I scrapped the battery in my case .
I followed mostly the same steps but for anyone that want some pictures, I posted them in another thread
http://forum.xda-developers.com/zenfone2/help/q-lcd-replacement-procedure-t3135165
Can asus ze550ml screen will fit to ze550kl model
@Ptselv: probably best to start a new thread rather than hijack one that is several months old.
And to answer your question: No, a ZE550ML screen will not fit a ZE550KL phone. My suggestion: search AliExpress.com for "ze551kl digitizer" and you'll be likely to find what you need.
Good morning;
So, my Nexus 7 took a swim. Fortunately it was a quick one and I was able to recover it quickly and it found it's way into a nice dry rice bath following.
There it sat for a few days until it was nice and dry. Power it on and blammo -- tries to boot into recovery or safe mode.
Fast forward to my best understand of what is happening -- it thinks the volume rocker is being pressed 100% of the time.
So, anyone have any thoughts or suggestions on what I may be able to do? I guess I'll have to buy some sort of replacement part -- but presumably it's not a modular component I can simply replace.
Think I can just 'remove' the volume control entirely?
StabbingHobo said:
Good morning;
So, my Nexus 7 took a swim. Fortunately it was a quick one and I was able to recover it quickly and it found it's way into a nice dry rice bath following.
There it sat for a few days until it was nice and dry. Power it on and blammo -- tries to boot into recovery or safe mode.
Fast forward to my best understand of what is happening -- it thinks the volume rocker is being pressed 100% of the time.
So, anyone have any thoughts or suggestions on what I may be able to do? I guess I'll have to buy some sort of replacement part -- but presumably it's not a modular component I can simply replace.
Think I can just 'remove' the volume control entirely?
Click to expand...
Click to collapse
Just to be clear we're not talking about the plastic buttons protruding on the side of the tablet. Inside, barring some short on the circuit itself or fried components(this you can do by inspecting points of contact on the ribbon, the inside of the connector and the soldering traces at its end), the amber ribbon consisting of power, volume and microphone can be removed from the bezel by very slowly scraping the double-sided white tape underneath it from one end to the other (if you use a thin blade, make sure you insert it between the tape and the bezel and not between the tape and the ribbon itself).
Once out, you will notice that contact is made when the thin round metal plates are pressed together. There are 2 layers. If you again carefully peel off the upper layer (transparent mylar or film), you can see if anything is stuck in between (water or vapor), or that one plate is depressed permanently that it would make contact all the time.
The rest is just a matter of pushing it back to the normal position and realign both layers. Usually, there would be enough adhesive left for them to stick together without your having to add more.
graphdarnell said:
Just to be clear we're not talking about the plastic buttons protruding on the side of the tablet. Inside, barring some short on the circuit itself or fried components(this you can do by inspecting points of contact on the ribbon, the inside of the connector and the soldering traces at its end), the amber ribbon consisting of power, volume and microphone can be removed from the bezel by very slowly scraping the double-sided white tape underneath it from one end to the other (if you use a thin blade, make sure you insert it between the tape and the bezel and not between the tape and the ribbon itself).
Once out, you will notice that contact is made when the thin round metal plates are pressed together. There are 2 layers. If you again carefully peel off the upper layer (transparent mylar or film), you can see if anything is stuck in between (water or vapor), or that one plate is depressed permanently that it would make contact all the time.
The rest is just a matter of pushing it back to the normal position and realign both layers. Usually, there would be enough adhesive left for them to stick together without your having to add more.
Click to expand...
Click to collapse
Thank you for the reply.
Yes, the rocker buttons do continue to rock like a charm. I'll have to crack it open and have a look. Thank you for your advice.
I picked up a Samsung brand keyboard cover for my 813 today and was very disappointed to find that the magnets in the keyboard would shut the screen off when you flip the cover over so you can hold the tablet and use it without the keyboard.
I researched but couldn't find a solution that was even remotely practical.
I figured out that if you fold the cover like I did in the picture, there's enough space between the keyboard and the tablet that it doesn't trip the magnetic switch.
The cover is still folded on a way it's designed to and doesn't feel any different when using it.
Hope this helps.
so i assume this problem is not for specific covers then, i got a 'Superfly' case+cover that works like those for the ipad ones from Apple. the cover rolls back to create a triangle stand. when i try to fold it all the way back to create a flat back, the magnetic also sleeps the tab. so the only way to use it and holding it is to roll it back and making it a stand and hold the stand itself.
very frustrating as sometimes i would like to fold the cover back and lay flat on table or on my palm but it just sleeps it.
only way to hold it on the hand is the like pic attached.
it seems like the sleep magnets are towards the left of the device, because when i close the cover half way where the right side of cover is still far from the screen, it puts it to sleep. same for the rear
sorry for thread jack though, i'm on the same boat as you
I think that the magnetic switch is near the home button.
Would it be possible to put a metallic barrier on the back of the tablet between the back flap to prevent the magnet on the front flap triggering the switch?
Metallic Plate Works!
Putting a metallic barrier actually works very well. I got a magnetic phone holder for my car which came with 2 metal plates (with adhesive) that you can stick to your phone back. I didn't need the larger one and tried it with the Tab S2 (9.7) official keyboard cover. And it worked!
The pictures show where exactly is the "sweet spot".
Update: Apparently the position outside the box reverses the effect - switches off when you remove the keyboard. The solution I found is to wedge the metal plate behind the cover just near where the cover snaps to the tablet. Works perfect!
Nougat Updates solves the auto-off bug
The auto-off problem seems to have been solved with the Nougat update. After the update when I connected the keyboard cover, the touchpad was not working. I unpaired and paired the keyboard again. Got both the keyboard and touchpad working. Then discovered that the auto-off bug is also solved when I folded it in reading mode with the keyboard in both on/off positions.