[Q] Getting "FAIL" in Odin when attempting to unroot. - T-Mobile Samsung Galaxy S 4

I flashed CM10 on my phone and now I can't seem to go back to stock, I have followed the instructions and this is what Odin is giving me:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUAMDL_M919TMBAMDL_M919UVUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Try a different USB port or USB cable, I've had this problem too before and it worked after.

johnny crapple said:
Try a different USB port or USB cable, I've had this problem too before and it worked after.
Click to expand...
Click to collapse
Just tried this, still not working.

Might be something else then, do you have knox?

Bcohn said:
Just tried this, still not working.
Click to expand...
Click to collapse
Try another different cable.?
☞ Sent from here☜???

Bah oh well like I needed another reason to get the note 3, thanks for the replies all!

Bcohn said:
Bah oh well like I needed another reason to get the note 3, thanks for the replies all!
Click to expand...
Click to collapse
Dumb question... what firmware did you previously have and what are you trying to flash. 4.3 can't revert to 4.2.2 is why I'm asking... if that doesn't apply to you, nevermind.

Related

[Q] odin error

I'm trying to flash back to my origanal firmware and I keep getting this error in odin.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUAMDL_M919TMBAMDL_M919UVUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know how to fix this issue?
What's the current firmware you're running?
☞ Sent from here☜???
baseballfanz said:
What's the current firmware you're running?
☞ Sent from here☜???
Click to expand...
Click to collapse
I'm running 4.2.2. I can't get triangle to work either so i can't do the update and my wifi isn't working right now. I was running 4.3 but was having problems with sending and receiving texts.

[HELP]Note 2 stuck at tmobile screen

A friend of mine bought a refurb note 2 a while ago and im trying to help her fix her phone. The problem is it's stuck on tmobile bootscreen and it wont boot to recovery mode for some reason. Although it can boot to download mode and I doubt its rooted cause knox warranty says 0, I could be wrong though. Has anyone had this problem? Any help/suggestions would be greatly appreciated.
EDIT: I just tried premiatul's suggestion earlier but odin gave me an error.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I used the 4.3 JB Stock Rom and it didn't work. Now I'm back to square one
Flash this with ODIN:
http://forum.xda-developers.com/showthread.php?t=1975560
Sent from my SGH-T889 using xda premium
premiatul said:
Flash this with ODIN:
http://forum.xda-developers.com/showthread.php?t=1975560
Sent from my SGH-T889 using xda premium
Click to expand...
Click to collapse
Should I flash it with 4.3 jelly bean? Idk what version she has but does it matter?
premiatul said:
Flash this with ODIN:
http://forum.xda-developers.com/showthread.php?t=1975560
Sent from my SGH-T889 using xda premium
Click to expand...
Click to collapse
I just tried premiatul's suggestion earlier but odin gave me an error.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I used the 4.3 JB Stock Rom and it didn't work. Now I'm back to square one
Anyone? I'm not sure If I'm even flashing the right ROM cause I don't even know the phone's firmware version.
Bump!

[Q] [solved] i9195 - doesn't work mobile network and wifi

Hi guys,
after a lot of problem with my s4mini now the phone doesn't call and doesn't active the wifi connection. I've tried to flash all the modem i found, but every time the process is concluded with a fail (in odin)...
So i don't know i can i do.
Thanks to all
Atlantis
Try flashing a complete new firmware with Odin.
RoyaLKurTx3 said:
Try flashing a complete new firmware with Odin.
Click to expand...
Click to collapse
I tried many times but evrytime the process ends with a fail... Odin lets me flash only te recoverys...
atlantis87 said:
I tried many times but evrytime the process ends with a fail... Odin lets me flash only te recoverys...
Click to expand...
Click to collapse
Tell me all the steps that you are doing. And if you can, provide me some screenshots.
RoyaLKurTx3 said:
Tell me all the steps that you are doing. And if you can, provide me some screenshots.
Click to expand...
Click to collapse
Everything starts wit a mistake. I had CM snapshot 12 and i tried to flash the stock rom. Probably i wrong the version of the stock firmware. When the process ends with a fail the phone was softbriccked... I tried many things (exactly i don't remeber every thing i done...) and at the end th only way i found was to flash a new recovery. After that i flash CM12 but when i turn on the phone all the mobile connection (network and wifi) don't work... I tried to flash a lot of different modem but no one works...
I attach the screenshot of the dowload mode...
Thanks
atlantis87 said:
Everything starts wit a mistake. I had CM snapshot 12 and i tried to flash the stock rom. Probably i wrong the version of the stock firmware. When the process ends with a fail the phone was softbriccked... I tried many things (exactly i don't remeber every thing i done...) and at the end th only way i found was to flash a new recovery. After that i flash CM12 but when i turn on the phone all the mobile connection (network and wifi) don't work... I tried to flash a lot of different modem but no one works...
I attach the screenshot of the dowload mode...
Thanks
Click to expand...
Click to collapse
hi man try this :1 instal a custom CWM....2 enter to recovery mode 3-wipe data factory and wipe cach..3 format dalvik cach 4 format system and format modem...5 enter to odin mode 6 flach your stock rom 7 enjoy
Hi man. I have already tried step 1 2 3. Do you know how can i format statemi and modem? Thanks
atlantis87 said:
Hi man. I have already tried step 1 2 3. Do you know how can i format statemi and modem? Thanks
Click to expand...
Click to collapse
ok men 1 go to recovery 2 go to mounts and storage 3 format system 4 format modem 5 fomat cache.and after this flash your stock rom
ok, i tried and....
nothing
when i try to flash something odin answer the row below...
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
But... a question... in the download mode the last row is "WRITE PROTECTION: ENABLED"... Can influence somthing this thing??
Thanks
Be careful when you format system, it's dangerous and the only fix for it is flashing a ROM.
Try these:
1. Download this and extract the files in the ZIP: http://www.sammobile.com/firmwares/download/40040/I9195XXUCNK4_I9195OXXCNK5_SEE.zip/
2. You should get 2 files;
I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5
SS_DL.dll
Ignore the SS_DL.dll. You will use the other file.
3. Go to Odin and thick only 'Auto Reboot' and 'F. Reset Time'. Now Insert the .tar.md5 I named above in the AP place.
4. Turn off your phone and boot into recovery. Clear data and cache. Now restart to download mode.
5. If you are asked to continue or to cancel and restart phone, choose continue.
6. Keep your phone like that and check that you have this (or similar) layout in Odin;
Now press start and wait until everything have finished and your phone boots (May take 8-11 minutes) If you followed these steps and you got a fail, then you must have done something wrong or your phone has something wrong in terms of hardware. Good Luck mate.
atlantis87 said:
ok, i tried and....
nothing
when i try to flash something odin answer the row below...
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
But... a question... in the download mode the last row is "WRITE PROTECTION: ENABLED"... Can influence somthing this thing??
Thanks
Click to expand...
Click to collapse
put your rom file in odin in (ap)....you can download your rom from sammobile.and try again try the metode up
RoyaLKurTx3 said:
Be careful when you format system, it's dangerous and the only fix for it is flashing a ROM.
Try these:
1. Download this and extract the files in the ZIP: http://www.sammobile.com/firmwares/download/40040/I9195XXUCNK4_I9195OXXCNK5_SEE.zip/
2. You should get 2 files;
I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5
SS_DL.dll
Ignore the SS_DL.dll. You will use the other file.
3. Go to Odin and thick only 'Auto Reboot' and 'F. Reset Time'. Now Insert the .tar.md5 I named above in the AP place.
4. Turn off your phone and boot into recovery. Clear data and cache. Now restart to download mode.
5. If you are asked to continue or to cancel and restart phone, choose continue.
6. Keep your phone like that and check that you have this (or similar) layout in Odin;
Now press start and wait until everything have finished and your phone boots (May take 8-11 minutes) If you followed these steps and you got a fail, then you must have done something wrong or your phone has something wrong in terms of hardware. Good Luck mate.
Click to expand...
Click to collapse
Hi,
i tried also this... Odin says:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
... i'm little bit disperate...
You inserted a modem.tar.md5 not the file I told you.
atlantis87 said:
Hi,
i tried also this... Odin says:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
... i'm little bit disperate...
Click to expand...
Click to collapse
dont be afraid my friend this is simple...so dont put the file in the modem pit it at (ap) colone...try a difirent odin v 3.09 okey ..dont missed to extract the zip file for your file rom okey and gry again
RoyaLKurTx3 said:
You inserted a modem.tar.md5 not the file I told you.
Click to expand...
Click to collapse
Sorry, i wrongly paste the odin row... The follow row are the correct...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
atlantis87 said:
Sorry, i wrongly paste the odin row... The follow row are the correct...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try everything again on a different computer, if you can.
RoyaLKurTx3 said:
Try everything again on a different computer, if you can.
Click to expand...
Click to collapse
Ok, thanks... i made all these trial on a macbook using vmware fusion with windows 8. I can try on another mac (with vmware and windows 8)... Do you think that can be work with another mac or is necessary to try with a pc?
atlantis87 said:
Ok, thanks... i made all these trial on a macbook using vmware fusion with windows 8. I can try on another mac (with vmware and windows 8)... Do you think that can be work with another mac or is necessary to try with a pc?
Click to expand...
Click to collapse
Try using windows.
RoyaLKurTx3 said:
Try using windows.
Click to expand...
Click to collapse
i tried and.... it works! However wifi and mobile network don't work. Do you have any other suggestion?
Thanks
RoyaLKurTx3 said:
Try using windows.
Click to expand...
Click to collapse
Maybe i found something... My IMEI is null... and i don't have a backup...

Odin FAIL! Need some help please.

Hello all,
I have a Samsung Note 4 from sprint. I tried rooting my phone earlier and then it just began to restart over and over. I researched and found some solutions which none have worked thus far. Maybe someone can help me out. Current things that I have tried.
1. Rebooted the device and did a factory reset and clearing the cache hoping that would fix the problem. The phone just continued to restart.
2. Next I downloaded the original firmware for my device that I found. The name was GalaxyNote4/SM-N910P/5.0.1/N910PVPU1BOB7_N910PSPT1BOB7_SPR.zip I tried using this and got the Fail! using Odin3 V 3.10
Here is what the Log says:
ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910PVPU1BOB7_N910PSPT1BOB7_N910PVPU1BOB7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be much appreciated, thank you for your time.
What firmware/rom did you start with? Sounds like you were on something beyond OB7, like OE1, OF5 or OG5 none of which will allow downgrading to OB7.
Sent from my SM-N910P using Tapatalk

Freedompop - Sprint Galaxy S3 SPH-L710

I recently bought a phone from Freedom Pop for one of my kids, I not a fan of how the phone uses there dialer and there text message app so, i want to revert the ROM back to the Sprint stock ROM and i'm running into some issues and i'm stuck
I have download the rom from here http://stockroms.net/file/GalaxyS3/SPH-L710
i'm using Odin3 v3.09 (i have also tried and older version did work)
and I have installed the drivers for the phone
when i start to flash the phone i receive a fail error
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_L710VPBMD4_L710SPRBMD4_1130792_REV03_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I think i have ran into the issue before with another Sprint Galaxy S3 that i root and then reverted back to stock but don't remember how or what i did to fix, I think it's related to the ROM but i need help as i'm trying to give this a gift for son for christmas
solved - i found another room from http://www.sammobile.com/firmwares/confirm/41671/L710VPUDNJ2_L710SPRDNJ2_SPR/ that worked with no issue
mcolvin2005 said:
I recently bought a phone from Freedom Pop for one of my kids, I not a fan of how the phone uses there dialer and there text message app so, i want to revert the ROM back to the Sprint stock ROM and i'm running into some issues and i'm stuck
I have download the rom from here http://stockroms.net/file/GalaxyS3/SPH-L710
i'm using Odin3 v3.09 (i have also tried and older version did work)
and I have installed the drivers for the phone
when i start to flash the phone i receive a fail error
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_L710VPBMD4_L710SPRBMD4_1130792_REV03_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I think i have ran into the issue before with another Sprint Galaxy S3 that i root and then reverted back to stock but don't remember how or what i did to fix, I think it's related to the ROM but i need help as i'm trying to give this a gift for son for christmas
Click to expand...
Click to collapse
The ROM that it ships on from FreedomPop is pretty much the Stock Sprint ROM with minor changes. You can just uninstall/disable the applications mentioned.
You should follow the instructions here if you want to use ODIN and flash the unmodified Stock Sprint ROM.
EDIT: Oops missed the second post
I just used TWRP. I've never used Odin.

Categories

Resources