"Firmware upgrade encountered" message - Sprint Samsung Galaxy S III

I've searched this forum and the internet for hours. When I power up my phone I get the message "Firmware upgrade encountered an issue.
When I put it in ODIN and try to flash a stock rom it fails and reads SV REV CHECK FAIL : Fused 1 > Binary 0
Is there any way to get my phone working again? Thanks!

Related

Urgent help needed...download mode blinking

Friends,I recently flashed my wave 2 s8530 to bada 2 and yesterday when i tried to flash it june update indian firmware(s8530 DDKF1) ,the flashing failed midway.I was getting rsrc1 erase error.I tried to flash it again still d error didn't go.After some time my phone showed "SOFTWARE UPDATE FAILED" error.Now i can't even enter the download mode.When i try,the download mode comes and after 5 sec the screen becomes blank or d software update error shoots up...I dont know what to do and I dont want to give it to the service center because i need the cell in working condition by sunday...Please help.
Try these options:
1. Make sure all necessary drivers are installed.
2. USe the correct version of multiloader to flash (flashing back from a different bada version usually has problems with multiloader v5.62 e.g. erase error).
3. Remove battery from phone for a mimumum of 10 minutes. Then insert battery again. Please borrow a fully charged battery from a friend (as yours obviously cannot be charged now).
4. Try flashing again.
Best of luck.

tried to flash root66_ATT_I317UCAMA4.7Z looks like messed up, need help

Hi, I downloaded root66_ATT_I317UCAMA4.7Z and extracted root66_ATT_I317UCAMA4.tar.md5. Using odin 3.07 I assigned PDA field to root66_ATT_I317UCAMA4.tar.md5 but at the end of download progress, I got fail status on Odin interface.
At the top left corner of the screen, it says "DW REV. Invalid magic string"
Also prior to doing that during one of the attempts, i might have disconnected the USB cable and now phone will display following message as soon as I connect:
"FW upgrade encountered an issu. Please select recovery mode in Kies & try again."
I also installed Kies and do a emergency but ****ing thing is asking for some code from previous installation and ****.
Any help recovering using anything but not Kies?
Thanks.,
Can you get into download mode? If you can, try downloading and install the stock MA4 firmware from sammobile.com.

Note 3 SM-N900 stuck at "Firmware upgrade error" Please help!

Hello everyone,
Hope you are well.
I am having a bad day with this Note 3. After resetting the stock firmware, it kept on giving a yellow sign at the notification bar that says "unauthorised operation detected, please reboot to prevent changes". Note that this is after full reset and no update or anything installed. After It restarted, it did something which looks like when a device gets a rom update (like those tools working on the droid belly), and after that it rebooted and keeps showing "Firmware upgrade encountered and issue, Please select recovery mode in Kies and try again".
I installed Kies 3 and it detects the phone but then says its not supported. If I try to do an firmware initialization and recovery, it asks for the phone model and serial number, after I enter both, it comes up with a message saying "SM-N900 does not support initializing."
Odin can't flash the phone either, its coming up with and error says write failed.
Please advise on how to proceed from here.
Many thanks in advance.

s6 edge g925t strange

i need ur expertise i have s6 edge g925t i try to downgrade with 6.0.1 to 5.1 but suddenly my phones stock on logo
the i reflash again to marshmallow rom 6.0.1 with this file G925TUVS5EQA2_G925TTMB5EQA2_G925TUVS5EQA2_HOME.tar .md5 the phone update complete but it shows drk failed
drk repair z3x
Checking local file... Ok
Searching server... Ok
Compare local and server file... OK (up to date)
Searching USB Flash interface... COM11 detected
Setup connection... Ok
Reading data from phone... Ok
Sending data to phone... error timeout
It looks like you have an unsucessful operation, try this link for solution - inurl:f453 site:http://forum.gsmhosting.com/ "Selected model: SM-G925T" "Sending data to phone error timeout" - Ïîøóê Google
Done with Samsung Tool PRO v.27.8
theres a post message on phone says (CUSTOME BINARY(CACHE) BLOCKED BY FRP LOCK)
then i try to frp reset via z3x again
Searching Samsung USB Flash interface... COM11 detected
Setup connection... Ok
Reading PITfrom phone... Ok
Searching FRP lock... Ok
Erasing FRPlock... Ok
Reset done
For complete reset FRP, goto 'Backup and reset' and make 'Factory data reset'
Done with Samsung Tool PRO v.27.8
frp reset says done but still frp on display on phone
i try to update samsung kies and also smart switch update complete but still always drk need to check on phone display
i download all firmware from 5.0.2 to 6.0.1 this is the only version G925TUVS5EQA2_G925TTMB5EQA2_G925TUVS5EQA2_HOME.tar .md5 make the phone flashing complete some others are not always from the start show sboot error
do you have any idea how to removed frp on 6.0.1 i try to use also combi files from support but at the start of flashing always failed....
this is the phone info
product name: sm-g925t
current binary: custom
system status: custom
frp lock: on
secure download: enabled
knox warranty void:1 (0x0301)
rp swrev: b:3 k:2 s:2"
i got knox tripping
i try to use this method still same problem
PHP:
https://forum.xda-developers.com/tmobile-galaxy-s6-edge/general/how-to-to-5-0-2-t3142946/page6
You can't revert if you flash MM bootloader, which unfortunately good sir. You have done.

Help!!! I got a code om my Note 7 N930FD after I restarted the device.

I have been upset about this problem for several days.:crying::crying::crying:
A few days ago, my phone was turned off because there was no power, but when I plugged it in and restarted, it appeared on my screen: custom binary blocked by frp lock.
I tried using odin3 with the original rom to fix him but it didn't work, and I have tried dozens of update packages in a few days.
I think it may be because this one was bought by a former person into an unofficial 9.0 file but I don't know the version of the file.
After searching, I think it is enough to install the original system, but I have failed!
The Odin3 versions I have tried are: 3.11.1, 3.13.1, 3.12.3.
I also tried multiple versions of Rom from different sites, but each failed.
My computer can successfully read the phone, but when I put the file, press start, it will display the fail immediately, then the phone will appear " kernel rev check fail device 2 binary 0" or "kernel rev check fail device 3 binary 2."
If I only choose '' CP '', I can succeed. If I check other, it must fail.
Last but not least, I have another question, that is, my mobile phone is from Taiwan, and the model written on the back is N930FD, but my Download Mode shows that my mobile phone is N930F.
Here are the information currently displayed on my screen:
ODIN MODE
Download Speed: FAST
PRODUCT Name: SM-N930F
Current Binary: Samsung Official
System STAUS: Official
FRP LOCK: ON
Secure Download : Enabled
CCIC=S2MM005 hw: 3 boot:5 main:09
Warrantly VOID: 1 (0x030c)
RP SWREV: B:3 K:2 S:2
DID= 00358cb8a53c
DDI= HA5_416000
I hope that you can help me solve the current difficulties, and I also apologize for my poor English.
N9300FD
你试试用Odin刷入TWRP,然后在TWRP里面卡刷9.0固件包试试

Categories

Resources