Hi, my phone is running ARHD 13.0, but yesterday something strange happened. The screen started to not work, only touch was working. Sometimes it worked, but it wasn't often. Now when I got this working, touch stopped working. I have warranty and I want to unroot it and get back to stock ROM & relock it and flash stock recovery. How do I do this without a screen?
As title says touchscreeen and cwm recovery not working
I can boot up XP but screen doesn't work but all buttons work, but when I hard reset and press back button it doesn't enter recovery
what i have tried and tested
Tried 2 working digitizer and three working ear piece ribbons
and recently changed the sliding ribbon due to the common wear and tear problem
flashed .58 firmware (with custom kernel and stock kernel) FAILED!
tried doom kernel and lupus kernel, no difference still wont boot into recovery
stock rom and custom roms, still wont work
First digitizer failure started off as temperamental were if just pulled out battery and restarted it might go way and then became laggy
then last time it work perfectly for 12 hours and then suddenly it completely stopped and never worked again:crying:
Has anyone had similar problem or know what could be causing it as i have tried everything I can think of.
I know its not rom, kernel or firmware causing problem as i have stuck to using gingerbread OS
and all hardware mentioned above worked flawlessly before problem but I still checked with other spares I had
Hi ive searched high and low but cant find a solution to the problem i have. I have a note 2 international GT-N7100, Ive recently replaced the whole front module as I dropped my phone and broke both the outer glass and the inner screen, (at this point I was running Bobcat ROM 10.1 with persus alpha-36 kernel) both before and immediately after all sensors worked perfectly then a couple of days later the accelerometer and gyroscope stopped working, i searched the web and found that most people suggested reverting back to stock ROM..... I did......and they worked again so i re-flashed Bobcat ROM and they still worked...well for the day, then in the evening they stopped again and havent worked since, i have tried the previous solution of flashing stock ROM/Recovery/UNrooting but still nothing, does anybody have anything for me. Maybe a way to reset the sensors or a file that could help. Thanks in advance.
I have a similar story - was running one of the Cyanogenmod nighties, all sensors working OK. Flashed CM 10.1.3 and they stopped working. Timeline something like this:
1. Flashed cm 10.1.3, no sensors (verified by running Androsensor - reports "waiting for event")
2. Factory reset, nandroid restore back to nightly release - sensors working again
3. Flashed CM 10.1.3 again, sensors working
4. At some point later, sensors stopped working again
Will try the factory reset - re-flash again but interested to get someone else's thoughts on this - anyone else had similar problems with CM 10.1.3 on the N7100?
Possible fix
Here is a solution to sensor problems, especially after flashing custom firmware to the GSN2 is this:
Turn off auto rotate, power off, boot into Odin/download mode. Once there - pull battery and reboot. Turn auto rotate back on, should work fine. Otherwise may be a hardware or firmware issue...Hope this helps somebody.
Warlock959 said:
Here is a solution to sensor problems, especially after flashing custom firmware to the GSN2 is this:
Turn off auto rotate, power off, boot into Odin/download mode. Once there - pull battery and reboot. Turn auto rotate back on, should work fine. Otherwise may be a hardware or firmware issue...Hope this helps somebody.
Click to expand...
Click to collapse
Thanx .. it solved my gyroscope sensor problem ... Don't you know something like that for magnetic sensor?? Mostly I feel it is hardware problem
Warlock959 said:
Here is a solution to sensor problems, especially after flashing custom firmware to the GSN2 is this:
Turn off auto rotate, power off, boot into Odin/download mode. Once there - pull battery and reboot. Turn auto rotate back on, should work fine. Otherwise may be a hardware or firmware issue...Hope this helps somebody.
Click to expand...
Click to collapse
Good night man, i just not understand this.. "take battery off when phone is plugged in usb and Odin reconizes this.... its right? and after i take the battery of the phone still on at download mode, how do i reboot it? just have to take off the usb? after i put the battery again and turn it on plus turno the auto rotate on? that's it? i doing it right? Thanks a lot for your help
I have the same problem and do not know perform the procedure. I would have to send more detailed procedure for my email?
[email protected]
Thank you
In My Note2 rotation sernsor, gyroscope has stoped working. Before helped wipe dalvik cache and cache. After reboot rotation worked to first deep sleep phone, after I must repeated the procedure. But now I check on 3 unoffical roms, and 1 oryginal software and sensor not working. After procedure from this thread - not work again...
Ok
i updated the firmware with odin last version to this OFW T210XXANC2_T210OXXANC2_T210XXANC2_HOME.tar.md5
All worked fine and the tablet kept the data, etc.
Now i installed the cwm and the 'android-armeabi-universal-root-signed.zip' from it.
For some reasson the tablet now is bricked for unknown reassons and its screen doesnt respond to finger touchs.
The tablet buttons and sound and booting works, but because the screen doesnt detect touchings, i cant do anything.
I have tried to install other cwm versions etc, and to reinstall the firware, and also that pre-rooted firmware on this forums, reset factory from cwm, etc. No success unfortunatelly.
Please help
anybody ?
i have installed kitkat firmware, the screen doesnt respond touchs
i have installed last jelly bean firmware, the screen doesnt respond
i have installed stock firmware, stucked in the samsung logo
help !
rotation sensor works, buttons works.
same problem ....
arfgh said:
anybody ?
i have installed kitkat firmware, the screen doesnt respond touchs
i have installed last jelly bean firmware, the screen doesnt respond
i have installed stock firmware, stucked in the samsung logo
help !
rotation sensor works, buttons works.
Click to expand...
Click to collapse
You have installed a rom for ROmanian Tab 3 7' Wifi, if you rezolved the problem please let me know how you did it becouse i have the same proplem and i tried everything , i try to install - uninstall a lot of ROM'S Kernel but no response the TAB3 is suck in Samsung logo or TAB 3 Logo . Please Help with a working rom or kernel ...
I had this when playing around with stock kit kats italy to france holland then back to stock jely bean then nole kat rom
Flash the stock firware for yhe tab with odincheck auto restRt and ftime is only on
Right after its near the end off flashing its gonna reboot keepp cable connect still
And hold home button and volume up when it turns off from downloading screen
get in stock recovery mode wipe cache and factory wipe
And reboot system
As its reboot hold home and volume down to get downloading screen
check at top thats its both offical if yes power off and start up
If no reflash again and do the same then it work to setup
Most off the time 2 flashes off stock does the job
I switched off my p2 and then after sometime when i switched it on it got stuck in bootloop .i booted recovery touch was working first time. I rebooted again but again bootloop then again i booted twrp but this time touch didnt worked . i even flashed the stock rom but still touch is irresponsivce. EVERYTHING ELSE IS WORKING FINE WITH A MOUSE. THERE IS NOT EVEN ANY DAMAGE AS I NEVER DROPPED MY P2. PLEASE HELP IF ANYONE KNOW WHAT HAPPENED
Just use gesture or open recent apps and then click on same app....everything would work fine...and yes it is a problem with havoc new update