I have TOT files, I have BoardDiag (different versions), but when I follow the countless instructions online I always get "Device was not found in dload trying flash programmer.".
Where do I go from here?
Bro how are conecting your phone ..
If it is like ...
1: you installed the drivees for qualcome qhs bulk ..
2: device when conected now show under device manager as Qualcomm HS-USB QDLoader 9008
3:if above two are effermative tell me !! If not thwn again tell me...???
Check ure ports in d3vice manager
bravo2526 said:
Bro how are conecting your phone ..
If it is like ...
1: you installed the drivees for qualcome qhs bulk ..
2: device when conected now show under device manager as Qualcomm HS-USB QDLoader 9008
3:if above two are effermative tell me !! If not thwn again tell me...������
Click to expand...
Click to collapse
This is correct. I reinstalled the qualcomm driver, now it is COM3 and boarddiag from here works (http://open-freax.fr/guide-unbrick-your-lg-g3/), but emmc test fails.
"Failed to open partition from EMMC." It doesn't matter if I select Read/Write or Erase.
By the way, I didn't have to open my phone for the 9008 mode, it went there kind of on its own.
Quza said:
This is correct. I reinstalled the qualcomm driver, now it is COM3 and boarddiag from here works (http://open-freax.fr/guide-unbrick-your-lg-g3/), but emmc test fails.
"Failed to open partition from EMMC." It doesn't matter if I select Read/Write or Erase.
By the way, I didn't have to open my phone for the 9008 mode, it went there kind of on its own.
Click to expand...
Click to collapse
Bad news if emmc fails ..i supose its a hardware damage to your emmc chip ...
What was you trying when it happend ..?
Power outage during rom installation ??
During KDC flash it stopped working. After 15 minutes at 0% I restarted the phone.
Please could an expert help me unbrick my device, I flashed lollipop autorec on Marshmallow:/ I tried willcracker but stuck in BoardDiag v2.99a with ERROR – MAX number of partition.
In my Device manager I get Qualcomm HS-USB QDLoader 9008. Been trying for a week now!!! HHHHEEEEELLLPPPPPPPPPP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
HD2wally said:
Please could an expert help me unbrick my device, I flashed lollipop autorec on Marshmallow:/ I tried willcracker but stuck in BoardDiag v2.99a with ERROR – MAX number of partition.
In my Device manager I get Qualcomm HS-USB QDLoader 9008. Been trying for a week now!!! HHHHEEEEELLLPPPPPPPPPP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Try to go download mode if you can...switch of your phone....hold volume up and connet the cable see if you able to enter dowload mode then flash a kdz....kdz would be different from your current version....for example if you have v30b flash v30c
i also have the same issue. im now looking for partition.txt file anyone has it?
Espinosa_Rommel said:
i also have the same issue. im now looking for partition.txt file anyone has it?
Click to expand...
Click to collapse
U can extract it from kdz via boarddiag
my phone had error when detect emmc , I couldn't find the way to unbrick it
Sent from my Optimus G using XDA-Developers mobile app
paul_zm said:
U can extract it from kdz via boarddiag
my phone had error when detect emmc , I couldn't find the way to unbrick it
Sent from my Optimus G using XDA-Developers mobile app
Click to expand...
Click to collapse
after i extract tot and kdz theres no partition.txt inside. boarddiag show "not responding"
Anik49 said:
Try to go download mode if you can...switch of your phone....hold volume up and connet the cable see if you able to enter dowload mode then flash a kdz....kdz would be different from your current version....for example if you have v30b flash v30c
Click to expand...
Click to collapse
No I can't get download mode but is seen in device manager as Qualcomm HS-USB QDLoader 9008. Every time I try BoardDiag v2.99a it stops with this, "ERROR – MAX number of partition". Only sign of life is red and blue LED flashing. If I pull the battery and connect USB without battery holding volume up it shows a connection symbol on the phone screen.
I am on the same page
Is there any fix for this error message ?
Thanks
Paolo
While flashing a new image on my 32 GB Nexus 5X yesterday, I flashed the wrong bootloader and hard-bricked my phone. It won't respond to key combos I've tried and won't even load in a Download Mode. I stumbled upon this guide and was managed to have my Windows PC detect it as a"Qualcomm HS-USB QDLoader 9008" device under "Ports" in Device Manager. I don't know how to proceed further because the guide assumes a phone can be loaded into Download Mode and mine can't so it is undetectable in LGUpdate tool.
Could anyone help me with this? Thank you.
https://www.youtube.com/watch?v=91iQV5hm-Yw
this video above is my situation. when i go to download mode it redirects to lg logo.
i cant find a way that my pc detects my lg g4.
when i check in device manager there is no device either qualcom or qdloader
HELP ME PLEASE!
up
august28th330 said:
https://www.youtube.com/watch?v=91iQV5hm-Yw
this video above is my situation. when i go to download mode it redirects to lg logo.
i cant find a way that my pc detects my lg g4.
when i check in device manager there is no device either qualcom or qdloader
HELP ME PLEASE!
Click to expand...
Click to collapse
I have the same problem, i used Win32 to write system.img then "EMMC_ROM1_032G74_1803230737_00000000_20000000" on SD card to enter download mode but i get bootlooped after like 5sec i get in dw mode.
I used QFIL but it fails all the time.
Idk what else to try...
up
to acess QDLoader 9008 you need to short two pings in the motherboard
el.adnane said:
to acess QDLoader 9008 you need to short two pings in the motherboard
Click to expand...
Click to collapse
so i should open my lg g4? is it safe?
august28th330 said:
so i should open my lg g4? is it safe?
Click to expand...
Click to collapse
its already wasted so there is nothing wrong in trying but if u dont know let someone else do it
I attempted to flash Dirty Unicorn from they're site, which appeared to go well, then I proceeded to flash the TWRPinstaller.zip that was suggested from the maintainer for our device. when I tried to reboot from recovery I got a no OS message. I ignored the message and attempted to reboot. Now the phone doesn't normally power on or off(which may change once the battery dies), no boot animation, no recovery, no fastboot recognition. The computer recognizes the phone as Qualcomm HS-USB QDLoader 9008. I googled for hours last night trying to fix to no avail. Has any of our great devs found a way to atleast recover the bootloader screen. I think I can handle it myself from there with adb.
Solved: Use the first blank flash from the link to get back to bootloader screenhttps://firmware.center/firmware/Motorola/Moto%20Z2%20Force/Blankflash/
From bootloaderscreen put your ADB skills to work. I'm not too good with guides but this just saved me $175
mookiexl said:
I attempted to flash Dirty Unicorn from they're site, which appeared to go well, then I proceeded to flash the TWRPinstaller.zip that was suggested from the maintainer for our device. when I tried to reboot from recovery I got a no OS message. I ignored the message and attempted to reboot. Now the phone doesn't normally power on or off(which may change once the battery dies), no boot animation, no recovery, no fastboot recognition. The computer recognizes the phone as Qualcomm HS-USB QDLoader 9008. I googled for hours last night trying to fix to no avail. Has any of our great devs found a way to atleast recover the bootloader screen. I think I can handle it myself from there with adb.
Click to expand...
Click to collapse
I did the same, got the same. Can't confirm the Qualcomm HS-USB QDLoader 9008 device will be there.
No charge, no screen, does not turn on/off, no vibration. Worst: no bootloader... Again, could be different if the battery dies.
mookiexl said:
Solved: Use the first blank flash to from the link to get back to bootloader screenhttps://firmware.center/firmware/Motorola/Moto%20Z2%20Force/Blankflash/
From bootloaderscreen put your ADB skills to work. I'm not too good with guides but this just saved me $175
Click to expand...
Click to collapse
Three questions:
1. File there is NDX26.183-15_17. Is it the same for OPXS27.109-34-10 on which I'm now? I suppose I need to use the "Oreo" version (2nd file in the list).
2. Which tool/software did you use to flash it? Is there a step by step tutorial?
3. You say "from bootloader screen". What about if we do not have a bootloader screen but a black brick in our hands?
Technical said:
I did the same, got the same. Can't confirm the Qualcomm HS-USB QDLoader 9008 device will be there.
No charge, no screen, does not turn on/off, no vibration. Worst: no bootloader... Again, could be different if the battery dies.
Three questions:
1. File there is NDX26.183-15_17. Is it the same for OPXS27.109-34-10 on which I'm now? I suppose I need to use the "Oreo" version (2nd file in the list).
2. Which tool/software did you use to flash it? Is there a step by step tutorial?
3. You say "from bootloader screen". What about if we do not have a bootloader screen but a black brick in our hands?
Click to expand...
Click to collapse
Answers
1.NDX26.183-15_17 (All it does is get your boatloader screen back
2. If you go to the device menu on your computer and your phone reads as Qualcomm HS-USB QDLoader 9008, all you have to do is click on the Blank flash all file and from the extracted folder and command prompt will do the rest. If the device is not recognized QDLoader 9008 then you will need to download qualcomm drivers to your computer
3.That is exactly what the file is for. Getting your black brick to at least the bootloader screen. From there you can adb recovery or stock rom.
What I ended up doing was adb push the bootable TWRP from the this thread https://forum.xda-developers.com/z2-force/development/how-to-install-oreo-ota-t3726932.
Flash the TWRP the official for our device from they're site(the bootable TWRP will give you access to extsd and thats where I had the official TWRP )
Rebooted back to bootloader and adb the firmware files for my device from the AOISP thread and rebooted my phone and I was booting DU.
Can somebody help me? I am in the same situation.
T-Mobile, unlock bootloader, hard bricked (already recognized Qualcomm QDLoader 9008 in device manager at least...)
I tried to use the blankflash but...see attachment
Dany XP said:
Can somebody help me? I am in the same situation.
T-Mobile, unlock bootloader, hard bricked (already recognized Qualcomm QDLoader 9008 in device manager at least...)
I tried to use the blankflash but...see attachment
Click to expand...
Click to collapse
Before connecting the phone, start the blankflash program. Maybe you have to repeat it a couple of times. Also try different cables, ports and computers.
Dany XP said:
Can somebody help me? I am in the same situation.
T-Mobile, unlock bootloader, hard bricked (already recognized Qualcomm QDLoader 9008 in device manager at least...)
I tried to use the blankflash but...see attachment
Click to expand...
Click to collapse
https://forum.xda-developers.com/showpost.php?p=77623934&postcount=5
mookiexl said:
Answers
1.NDX26.183-15_17 (All it does is get your boatloader screen back
2. If you go to the device menu on your computer and your phone reads as Qualcomm HS-USB QDLoader 9008, all you have to do is click on the Blank flash all file and from the extracted folder and command prompt will do the rest. If the device is not recognized QDLoader 9008 then you will need to download qualcomm drivers to your computer
3.That is exactly what the file is for. Getting your black brick to at least the bootloader screen. From there you can adb recovery or stock rom.
What I ended up doing was adb push the bootable TWRP from the this thread https://forum.xda-developers.com/z2-force/development/how-to-install-oreo-ota-t3726932.
Flash the TWRP the official for our device from they're site(the bootable TWRP will give you access to extsd and thats where I had the official TWRP )
Rebooted back to bootloader and adb the firmware files for my device from the AOISP thread and rebooted my phone and I was booting DU.
Click to expand...
Click to collapse
Can somebody please help me, my laptop isn't even detecting my device as QDLoader 9008, can you please tell me which windows os version did you use, also did you use the usb cable came in the box and did you use usb 2.0 port or 3.0?
LØNEWØLF said:
Can somebody please help me, my laptop isn't even detecting my device as QDLoader 9008, can you please tell me which windows os version did you use, also did you use the usb cable came in the box and did you use usb 2.0 port or 3.0?
Click to expand...
Click to collapse
Well, you need of course, Qualcomm loader driver, to at least having your device recognized as 9008. There u go: https://www.androidbrick.com/download/latest-2017-qualcomm-diag-qd-loader-windows-10-drivers-signed/
After that, go ahead with blankall and stuff...
P.s. and yes ..stay away from USB 3.0! ???
Dany XP said:
Well, you need of course, Qualcomm loader driver, to at least having your device recognized as 9008. There u go:
After that, go ahead with blankall and stuff...
P.s. and yes ..stay away from USB 3.0!
Click to expand...
Click to collapse
Thanks for the reply bro....but I have that driver installed...I installed before connecting it....still not detecting... I'm gonna try this once more in my friend's pc... let's see what happens
LØNEWØLF said:
Thanks for the reply bro....but I have that driver installed...I installed before connecting it....still not detecting... I'm gonna try this once more in my friend's pc... let's see what happens
Click to expand...
Click to collapse
I know it's a long shot but...do u have any other Qualcomm device to try?
U can enter EDL mode with adb command "adb reboot edl". Yes, it's that simple. ?
Dany XP said:
I know it's a long shot but...do u have any other Qualcomm device to try?
U can enter EDL mode with adb command "adb reboot edl". Yes, it's that simple. ?
Click to expand...
Click to collapse
OK I'll try...but how would I get back from edl to Normal without doing anything in the edl?
LØNEWØLF said:
OK I'll try...but how would I get back from edl to Normal without doing anything in the edl?
Click to expand...
Click to collapse
Uh...good question