Related
I have searched high and low for an answer on how to replace a scratched screen of the SGS2 by yourself and have finally found the answer.
This will definitely VOID YOUR WARRANTY so don't say you haven't been warned.
I suggest you only use this guide if you were desperate like me. My phone didn't come with an official warranty so I was as good as screwed if I wanted a new screen.
Step 1: Obtain the part
Just ebay for lcd screen and digitizer galaxy s2 (however u may wish to buy it with the faceplate see below note). You want both the super amoled plus screen and the digitizer together. You can get this for about 120-130 USD.
There are some vendors that sell just the 'lens' but you need a specialized machine to replace it and is simply not worth the trouble.
Note that if you go to an original Samsung service centre, when they order the part, it comes together with the face plate and is therefore a breeze to install. This part is for sale on Ebay too. http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0. I would recommend you to buy this type instead of just the LCD and digitizer.
Follow this disassembly guide (not mine).
Now using a thin metal flat tool with a wide flat surface area, dig at the small gap from the top of the screen and pry the screen from the frontplate. It is held entirely by double-tape so don't worry about any screws, catches. Be careful of not damaging the bezel in the process.
Clean off the old black tape and double tape as best as u can, and be careful of the bottom buttons. The attachment shows how it looks like after cleaning it.
Reapply the double tape in strips and try to shape it to fit as much as you can. This is tiresome but necessary since the adhesive behind the lcd screen is very weak and you don't your screen falling out of you halfway.
Push it in and it should stick. That's it! Then reassemble.
Confirmed working!
thanks for the write up, do you have any more photos of your process?
OMG, it's like watching an autopsy.
Could a better resolution screen or even 3d screen be used/upgraded later on?
Nice to know for something happens, Hope not
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Man,,u shud handle it a bit gently ,,,,i mean,i flinched every time u "threw" the phone on the table.
On second thought, I might as well buy that screen protector
Sent from my GT-I9100 using XDA Premium App
wow that is the definition of T H I N !!!!!
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
Thanks also full part with bezel here http://www.ebay.co.uk/itm/Samsung-G...062?pt=LH_DefaultDomain_3&hash=item3cb9ff0e4e
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable
http://www.ebay.co.uk/itm/LCD-Touch...669?pt=LH_DefaultDomain_3&hash=item3cb9ff0cc5
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable Without Samsung logo
White house soon on site
psp888 said:
thanks for the write up, do you have any more photos of your process?
Click to expand...
Click to collapse
Unfortunately not at this time. I will do it the next time around (which will be soon as there is a slight imperfection with my button sensitivity so I might be inclined to try it again) but trust me it's not a beautiful process. Needs lots of guts. Nothing technical about it. Shove the flat tool in the gap and keep on loosening the glue as much as u can then take it off.
podgo said:
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Click to expand...
Click to collapse
It's more like cracked. I dropped it on some rocks from waist height and it cracked. It seems that gorilla glass is not shatter proof. There are also some scratches/mini cracks from where the rocks cut it.
Lesson learnt, get a screen protector that hopefully will reinforce it a bit more.
I wonder how these replacement parts compare to the quality of the original parts.
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
psp888 said:
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
Click to expand...
Click to collapse
There some listed as Super AMOLED+ screen just search on ebay or even drop the sellers a question about their iteams.
It is a Super Amoled + screen (don't see any difference in quality between the old and new one). Most sellers don't really know much of their products unfortunately but they do say it's original and I do believe mine is.
There's no Samsung print on the front plate but it does have a part number which corresponds closely to the original one. Everything else looks exactly the same, even the black sponge at the back and the microchips have Samsung wording on them.
BarryH_GEG said:
OMG, it's like watching an autopsy.
Click to expand...
Click to collapse
I have stomach to watch dead bodies, but not a GSII LOL
Dropped SGS2 from bikemount : broken screen.
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
DirkB19 said:
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
Click to expand...
Click to collapse
It is very easy to do. Just unclip each component and transplant it to the new case.
I have to do my friends one this weekend as he has dropped it and damaged the screen and the bezel .
I have managed to source the screen and the bezel for him all as one piece .
Now all the guides i have seen just rip the phone to pieces , surely if we have the right bits like i have bought this fix is very smple to do??
I am thinking it is just a case of undoing the 7 screws at the back of the phone , opening it up and then disconnect the screen cables from the mainboard . Does the whole front then come away??
If not i take it i have to undo the screws on the main board to release the screen? but this means the componets of the main board may come loose etc??
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
buxz777 said:
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
Click to expand...
Click to collapse
+1 for me.
I received my screen including bezel.
I've removed the main board just like the guy in the Youtube video.
But now I still have to transfer (from original front to my new front):
- the bottom PCB (where the microUSB sits)
- the camera
- the speaker
etc ...
I can not find a description/movie of how to do this ?
The bottom PCB for example has 2 screws, but after removing them the PCB itself looks like glued to the front assy'.
I prefer to see or get proper instructions before starting the rest of this adventure
...
PS : I got my part from aliexpress.com within 2 weeks (via airmail). It's with the Samsung logo on it and the package included all required tools (screwdrivers) to do the job. Would be nice to see some written instructions included as well.
Grtz,
DirkB
Yep, I broke my galaxy. Screen and touch sensor works awesome, but screen is fully shattered. Searching at the forum gave me one positive result: http://forum.xda-developers.com/showpost.php?p=23644712&postcount=6
But i cant find any guide anywhere. If someone know how to make this kind of operation please leave your post or guide, it would be great. Thanks in advance!
Hello,
youtube is your friend
http://www.youtube.com/watch?v=65pvAINg2ME&feature=my_favorites&list=FLhOahoxI-440fS-S2edtp7w
glass only video - hmmm...
exeq said:
Hello,
youtube is your friend
http://www.youtube.com/watch?v=65pvAINg2ME&feature=my_favorites&list=FLhOahoxI-440fS-S2edtp7w
Click to expand...
Click to collapse
the above is for the digitizer w/glass - the below is for glass ONLY
http://www.youtube.com/watch?v=CfuTVjI_Wao
It is very risky to replace the glass only. Doing it this way increases the risk of damaging the AMOLED panel, either by overheating it or scratched/cracked by the broken glass. I've explained it before; if you want to replace the glass only, you'll need to separate the screen assembly from the frame first, then separate the glass from the AMOLED panel. You might end up breaking the panel anyway, so might as well replace the whole thing. But you can give it a go. It should be possible to remove the glass while keeping the AMOLED panel in the frame, because the panel itself is very fragile.
I replaced only the glass on mine.
igor45 said:
the above is for the digitizer w/glass - the below is for glass ONLY
Click to expand...
Click to collapse
Hi. This is my story about SUCCESSFULLY replacing only the glass of s2.
Background, you can skip this:
Few months ago I broken the glass of my beloved S2 in an accident, but because I had a screen protector the pieces of glass were kept together and the phone was 100% usable, only the image was distorted because of broken glass.
So I searched the available options: replace the whole display for a price of more than 100euro. Buy a defect s2 with good screen, but didn't found any lower than the previous price.
I had a previous experience with an Ipod Touch with the same problem, when I ordered the glass from ebay and went to a local phone repair shop that destroyed the Ipod. It was usable before going to that shop.
So I decided to give it a try and try to change it myself. I'm a programmer with what can be called poor electronic and hardware skills. So if I was able to do it, and you were able to find this post, you can replace it too. But after seeing some videos I had more confidence on my skills than of those repair specialists that were not careful with the other device.
First I found a clip on youtube about why you CAN'T change only the glass on S2. But I found also the above video with a interesting method, but it required a Molybdenum string that I couldn't found at a good price. Actually I believe that the shipment to Romania made the price to high for the string.
After researching I found the SOLUTION: on a page or youtube clip about how to remove the broken glass. But I've lost the link. Anyway, the procedure was simple. I remember that the video was about replacing the glass on a Galaxy S3.
So I ordered the replacement glass and some adhesive (finally not used) from ebay.
After I got the replacement parts, I opened the phone, you can find somewhere online the instructions how to do it.
For removal I used a pack of plastic poker card. It's needed something to not be to hard to scratch the digitizer, but hard enough to remove the broken pieces of glass.
I started removing the pieces around the Home button to get a feel of the process, and proceeded to remove all the pieces of glass and glue. It took around 3 hours to finish it and 48 cards. You need to lift the broken pieces with great attention and patience. It's not a hard job, but it takes time. Maybe with a hot gun is easier to remove, but when I received the replacement I was anxious to start and did not wait to procure one. During the whole process I kept the phone started to be sure that I did not broke the screen. In case of possible breakage or of a bad scratch I thought that I don't need to continue the procedure. Maybe is not recommended to keep it running, but it gave me a positive feedback that everything is ok.
After removing all the pieces of glass and glue I was able to see some fine scratches with a black background. I used some dust removing solution and then I attached the new glass. I only fitted the new glass on the place and I believe there were some glue left on edges that keep it in place because I did not added any other glue and it did not moved until now. With the new glass the scratches from the digitizer are not visible at all. And the phone works as new, the touchscreen was not damaged at all.
So it's completely possible to replace it.
Before fitting the new glass the cleaned touchscreen was like the touchscreen on S4: it was only needed to hoover with a finger at some distance above, but not touching . I remember that the replacement of my glass was before the release of S4 and when I found about this feature I knew that I already had something like this on my S2.
I don't remember having any other difficulties during the replacement except the removal of broken glasses. And I used this phone continuously without problems since.
Only last night the phone stopped charging and I had to replace the charging port, flex ribbon; but it was not related to glass replacement.
I don't remember if it was needed to open the phone for glass replacement because I opened it when it broke to inspect it and I opened it also few time since then for various tasks.
The total price of replacement parts was below 10$, with glass, screen protector and adhesive ordered from ebay. I ordered also a case to protect the edges for future dropping and was a smart investment. The pack of cards I had from poker set, but It shouldn't be so expensive.
Success with your replacement.
KAWIN tempered glass screen protector for SAMSUNG GALAXY S2
buffon95 said:
Yep, I broke my galaxy. Screen and touch sensor works awesome, but screen is fully shattered. Searching at the forum gave me one positive result: http://forum.xda-developers.com/showpost.php?p=23644712&postcount=6
But i cant find any guide anywhere. If someone know how to make this kind of operation please leave your post or guide, it would be great. Thanks in advance!
Click to expand...
Click to collapse
KAWIN tempered glass screen protector for SAMSUNG GALAXY S2 top quality with best price !
http://www.xkxfilm.com/en/samsung/40-41.html: :good:laugh:
Don't try this at home kids...
I now back to my desire z after the galaxy screen is toast. JUST the heating alone destroyed it. ... Now gonna buy the LCD/screen assembly and do it right.
Sent from my Desire Z using xda app-developers app
if you are not a technician, I suggest you give it to someone REALLY capable of, what do you mean it is not at all easy and the risk of doing damage is very high.
Otherwise follow the advice that was given to you, buy the whole block
Necro thread, but I agree, it is not worth doing so. In order to be done properly, you need to have a very thin wire to separate the two pieces. Not something i would do myself. Much better to replace the whole assembly instead.
Relevant
test
Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?
I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I remember seeing that thread as well, I tried to find it, but could not.
justbecuz123 said:
I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
Click to expand...
Click to collapse
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
707BeastMode707 said:
I remember seeing that thread as well, I tried to find it, but could not.
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Are we talking about the glass or the whole display? It makes a big difference. Assuming all 3 displays are the same (i9250, L700, I515), the problem is separating the display from the frame plate. Its very difficult and you can crack it very, very easily if you try to remove it. The cheaper GN LCD's on eBay are from working units and those already have the frame plate attached to it. The only way to remove it is to use a heat gun and apply it on the top and bottom front areas (as well as the sides). The apply heat to the back frame plate to loosen up the adhesive in the mid section of the screen. Then, slowly and I mean very, very slowly try to pry it open using a thin blade. Start from the top and work your way down. You should stop if you meet too much resistance and reapply heat. Like I said its a pain in the ass and not for the timid. I got to successfully remove an LCD from a frame for a Galaxy S (i500) not too long ago, its a similar in process as the GNex
I also tried to remove a L700 LCD (cracked glass) from a frame a while back and cracked it even more. I know what I did wrong and I think I wont make that mistake again. My mistake was that I did not know the exact location of the adhesive and applied too much heat in the front. Another mistake was that I thought I could remove the front glass from the digitizer. Now I know this is almost impossible and I don't know how people can buy front lenses without using some type of special tools (a true hot air bga station for instance) or a technique that I'm not aware of.
So, that's my long rant right there. I would really appreciate if any of you can confirm that any all 3 displays are the same (i9250, l700, i515). If it is then I would dare to try it out and take some pictures in the process if all goes well.
What about the oven?
I used to be into cars, and it was popular to smoke the headlamps on Nissans. They also have a lot of glue in them, and it was recommended to put em in an oven lol.
I'm sure it would get hot enough to loosen the screen, but 400 degrees may break something else in the process...
Sent from my Galaxy Nexus using xda premium
Did anyone ever find the answer to this question? I am wondering the same thing.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
You can't use the i9250 screen on the i515. The battery metal thingies and the vibration thing are in different places.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
I have asked a bunch of eBay sellers for the last few days and have gotten mixed responses... I don't think that most of them get that I am talking about separating the display from the front case/plate. One guy told me that the digitizer/LCD combo is interchangeable from the i515 and i9250, but it won't work on the L700. One guy told me that he thought that the entire assembly including the front plate were the same between the L700 and i515. Several have said that they are model specific, but I don't think that most of them realized that I am not expecting to use the front plate from an L700 if i9250 on the i515...
It doesn't seem like Samsung would have a different display for each model. I can see the plates and cases being different because some of the other parts are different, but it seems like the LCD panel and the glass should be the same for each model. To me all of the screen connectors look the same from the pics I've seen...
Edit- I just found this online store that indicates they are the same screens http://www.globaldirectparts.com/OEM-Galaxy-Nexus-L700-LCD-Digitizer-Assembly-p/smsng6115350-qs.htm
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post.
Click to expand...
Click to collapse
Finally found the post that you are referring to (http://forum.xda-developers.com/showthread.php?t=1780491). Sounds like he ran into problems because he tried to use the i515's front housing on the i9250. I think if he had removed the screen from the frame and re-used the frame that was original to his phone he would have been fine. It looks like it takes some heat and care to do that, but it looks do able.
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
MrAreCool said:
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
Click to expand...
Click to collapse
L700 screen (not including frame) worked on my i515. Details here.
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
perusmuro said:
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
Click to expand...
Click to collapse
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
MrAreCool said:
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
Click to expand...
Click to collapse
I have found few videos where that glass is possible to remove.
http://www.youtube.com/watch?v=JlfO6TUj1DQ
But I think that I would buy that whole set and change that. But what is the best place to buy that? So I can real deal.
Ok guys, just wanted to confirm that front glass for the L700 and GT-i9250 the same. And I assume that i515 as well.
I got for repair Nexus Sprint (L700) with cracked front glass but then was surprised that glass for L700 on ebay about $15 and the same glass for i9250 less then $10. Not big deal but anyway.. So I bought the glass for i9250 and it fits great as original.
Good luck!)
When the purchase of parts and mobile phones are not matched, the proposed replacement.
Well search is down at the moment, so here goes: I have an Optimus G that finally met it's demise. My glass screen is completely shattered but the image underneath is still clear and no discoloration. Obviously it doesn't respond to touch anymore. Do I only need to purchase a digitizer to do the repair or should I get the digitizer+lcd replacement? I just need a simple clarification.
Digitizer and lcd. The lcd on a factory phone is 'glued' to the Digitizer I believe. I couldn't get the lcd off my original evo anyway
Sent from my LG-LS970 using Tapatalk 4
My wallet shed a tear
I guess a new phone?
Sent from my LG-LS970 using xda app-developers app
Swav3y said:
I guess a new phone?
Sent from my LG-LS970 using xda app-developers app
Click to expand...
Click to collapse
He might as well. Although I'm sure you can heat and remove the glass to attach a new glass if the LCD is still good, the price on the glass for the LGOG is a bit steep as its not just a piece of glass, its also the digitizer. A big difference from a Galaxy. I can easily get a glass for my Note at like 10-20 bucks and just glue it on and be all set. That is not the case for the Optimus G, the glass works as the digitizer which I'm assuming why it's a bit expensive.
Edit: I just looked into it some more and it definitely is a complicated task. In all the how to vids they replaced the whole thing, glass and LCD. I guess that's why it's hard to find just the glass. Most sellers sell the glass and LCD together already.
Edit # 2: I finally found just the glass for $38. It actually was 80 last night but I guess the seller dropped the price.
http://pages.ebay.com/link/?nav=item.view&id=181219758562
^^^That's what you need. However if you do attempt it be aware that there's no how to videos on separating the glass from lcd. So after heating up the phone to remove it from the housing you're more than likely going to have to reheat the screen again to begin the glass/LCD separation. Oh and you might need some LOCA adhesive and a UV light to bond the new glass in.
Sent from my SPH-L900 using xda app-developers app
you need both >> however i would go for an OEM one ....
i bought a cheap one from china, the ones without the LG logo on top, and it sucks. There is like a small strip that doesnt respond to the touch, its fine because i didnt notice until i started playing with "sketchbook mobile" but still. and it you look at it at an angle through the light its not smooth and perfectly straight like the original one, AND when you tap SLIGHTLY hard .. you see that liquidy effect ... not cool! .. not annoying either .. just a heads up if you do decide to fix it>
Kiresu said:
Well search is down at the moment, so here goes: I have an Optimus G that finally met it's demise. My glass screen is completely shattered but the image underneath is still clear and no discoloration. Obviously it doesn't respond to touch anymore. Do I only need to purchase a digitizer to do the repair or should I get the digitizer+lcd replacement? I just need a simple clarification.
Click to expand...
Click to collapse