hello there my names kyle and im new here but you can call me sangy, anyway i have joined the site to post this
i have had my play now for 6 months and i want ics and a new kernel, i heard lupus was the best one so i flashed lupus using fastboot and the correct rom. i have followed all steps correctly and the dam thing just boot loops after 1 min of booting unless i have my usb in my pc at which point the phone will stay on like it should without a single bootloop. so with a potentially bricked phone i flashed the stock firmware back v4.0.2.A.0.58 and re flashed a different kernel and rom still the same issue so i flashed back to stock again. if anyone can tell me how to solve this weird ass issue i will rate you +1 because im getting sick of having no cwm and incompatibilities with apps and i want to overclock
ps im planning on flashing doomkernel v14 hope this problem is gone but i know it will have the same issue.
my phones current state is this
xperia play r800i
stock kernel(2.6.32.9-perf) [email protected]#1
FW 4.0.2.A.0.58
baseband 64
android 2.3.4 ginger bread with root and unlocked boot loader
thats everything i know thanks for reading and helping in advance
edit: sorry if im not been precise but by boot loop i mean hot boot where the phone will run fine for 3 min then freeze and reboot on its own until i pull the battery or plug in usb in pc upon hard reset it even does this in kernel boot up
vampyregaming said:
hello there my names kyle and im new here but you can call me sangy, anyway i have joined the site to post this
i have had my play now for 6 months and i want ics and a new kernel, i heard lupus was the best one so i flashed lupus using fastboot and the correct rom. i have followed all steps correctly and the dam thing just boot loops after 1 min of booting unless i have my usb in my pc at which point the phone will stay on like it should without a single bootloop. so with a potentially bricked phone i flashed the stock firmware back v4.0.2.A.0.58 and re flashed a different kernel and rom still the same issue so i flashed back to stock again. if anyone can tell me how to solve this weird ass issue i will rate you +1 because im getting sick of having no cwm and incompatibilities with apps and i want to overclock
ps im planning on flashing doomkernel v14 hope this problem is gone but i know it will have the same issue.
my phones current state is this
xperia play r800i
stock kernel(2.6.32.9-perf) [email protected]#1
FW 4.0.2.A.0.58
baseband 64
android 2.3.4 ginger bread with root and unlocked boot loader
thats everything i know thanks for reading and helping in advance
edit: sorry if im not been precise but by boot loop i mean hot boot where the phone will run fine for 3 min then freeze and reboot on its own until i pull the battery or plug in usb in pc upon hard reset it even does this in kernel boot up
Click to expand...
Click to collapse
which lupus kernel, ics+gb v7 or lupus ics beta v12. have you tried flashing through flashtool because it always works for me and which ics rom as their are tons.
hello thanks for the quick reply
ive tryed the lupus ics+gb kernel latest version with the ics beta rom for xperia play and ive also tryed the lupus gb kernel latest version
and yes i have flash tool and all the drivers but a nice reccomendation on what to flash next based on my phones spec at the moment would be nice
also why am i the only person on the internet with this problem? ive heard of having 60+ apps on the sd to cuase hot booting but for me this is just out of the ordinare, particulary when ive whiped all the phone and flashed a new kernel.
vampyregaming said:
hello thanks for the quick reply
ive tryed the lupus ics+gb kernel latest version with the ics beta rom for xperia play and ive also tryed the lupus gb kernel latest version
and yes i have flash tool and all the drivers but a nice reccomendation on what to flash next based on my phones spec at the moment would be nice
also why am i the only person on the internet with this problem? ive heard of having 60+ apps on the sd to cuase hot booting but for me this is just out of the ordinare, particulary when ive whiped all the phone and flashed a new kernel.
Click to expand...
Click to collapse
With Lupus kernel, use R800i_4.0.2.A.0.79 firmware
will be flashing that stock firmware now over my other one then put lupus gb+ics over the stock kernel
will let you know if it goes well and fixes this
unfortunatly it did not fix it rom loads up, gets to the regular sony setup then freezes and hot boots. did this with lupus kernel ics+gb and the 4.0.A.0.79 firmware you linked me to. its either the kernel or my phone
just tryed doomkernel v14 with your FW kernel still crashes and reboots, is there something i have to do in flashtool because
every kernel ive flashed yet has the same issue.
note i can get a catlog app whilst it is plugged in then unplug it and wait for the crash and send it to you and you can see where its going wrong with the kernel and tell me what to do
thanks for reading these updates and sorry its taking this long to find and fix a big bug :good:
vampyregaming said:
unfortunatly it did not fix it rom loads up, gets to the regular sony setup then freezes and hot boots. did this with lupus kernel ics+gb and the 4.0.A.0.79 firmware you linked me to. its either the kernel or my phone
Click to expand...
Click to collapse
Did you tried any other ics/gb rom? Wipe your system/data from recovery before installing (and by installing i mean install from recovery with "install zip from sdcard")
Ps: maybe its stupid question, but is your sdcard full??? How much free space on it?
what recovery? this is an xperia play they dont have a recovery on stock kernels thats why im flashing one and no my sd card is not full
literally after i flash the kernal and boot up it will freeze and hot boot. the rom doesent factor in this. ive tryed 4 kernels so far the one that comes with cyanogen mod 9 and the 3 mentioned above
would flashtool logs be helpful if so tell me how to record them to a clipboard and you can see whats going on during the flash
vampyregaming said:
what recovery? this is an xperia play they dont have a recovery on stock kernels thats why im flashing one and no my sd card is not full
literally after i flash the kernal and boot up it will freeze and hot boot. the rom doesent factor in this. ive tryed 4 kernels so far the one that comes with cyanogen mod 9 and the 3 mentioned above
would flashtool logs be helpful if so tell me how to record them to a clipboard and you can see whats going on during the flash
Click to expand...
Click to collapse
For Lupus kernel - when powering on, keep pressing volume down for clockworkmod recovery or volume up for TWRP recovery.
Flash ROM from recovery that match kernel. Lupus ICS/GB V7 is for ics/gb roms based on stock (Sony) roms. Read in ROM's thread which kernel is recommended
With flashtool you can only flash .img files and in Xperia Play case, that is ONLY ics beta rom (but almoust all kernels come in .img format - so Flashtool is used to flash kernel). From recovery you can flash every other rom that you can find (just make sure that kernel match rom or else you'll get kernel bootloop)
ok this will be crystal clear
i can flash the kernal but even when booting the kernal and going into recovery to even flash a rom it will freeze and hot boot
meaning i did everything correctly with flashtool to do the kernel and with just the kernel installed (no rom) it still freezes and hot boots
as soon as i can stop these kernels from freezing i can flash whatever ics or gb there is in recovery
note: what are your settings for your flashtool as i might be missing a setting also the info from flashtool says at startup to disable MTP for 2011 devices, would this be my problem?
vampyregaming said:
ok this will be crystal clear
i can flash the kernal but even when booting the kernal and going into recovery to even flash a rom it will freeze and hot boot
meaning i did everything correctly with flashtool to do the kernel and with just the kernel installed (no rom) it still freezes and hot boots
as soon as i can stop these kernels from freezing i can flash whatever ics or gb there is in recovery
note: what are your settings for your flashtool as i might be missing a setting also the info from flashtool says at startup to disable MTP for 2011 devices, would this be my problem?
Click to expand...
Click to collapse
what kernel are you trying to flash? Be specific!
What rom are you trying to flash?
Disconnect phone from PC after you flashed your rom (any one, first boot must be done while disconnected)
the kernel i would like mostly is the lupus kernel
i can flash every kernel no problems, its the fact that the kernel crashes etc i can also flash the correct rom using flashtool the same thing happens
the case im trying to make is that you first install the kernel then flash your rom in recovery then the extras like wifi modules to the kernel
the kernel (dosent matter which one i try for my device ) has the hot boot issue happen to it no matter what i do before i even have a chance to install the rom(again the correct rom stock or not).
and yes i know you have to wait for boot ups on new roms and kernels, this isnt the first time i have flashed roms as i have a galaxy tab 2 running cm10 for the most part.
again thanks for the quick replys but i think this will require more technical solutions or debugging with my phone or software.
Install cwm on your phone. Search xparts on play store. Go into recovery and wipe system and wipe data and cache then turn off your phone. Open flashtool. Hold search while plugging your phone in and then flash kernel
Sent from my LT30p using XDA Premium 4 mobile app
FaiselW said:
Install cwm on your phone. Search xparts on play store. Go into recovery and wipe system and wipe data and cache then turn off your phone. Open flashtool. Hold search while plugging your phone in and then flash kernel
Sent from my LT30p using XDA Premium 4 mobile app
Click to expand...
Click to collapse
thank you for for saying that after 1 hour, will try that now and test the kernel for 20 - 5 min
if this works tell the kernel devs to make proper instructions on this
FaiselW said:
Install cwm on your phone. Search xparts on play store. Go into recovery and wipe system and wipe data and cache then turn off your phone. Open flashtool. Hold search while plugging your phone in and then flash kernel
Sent from my LT30p using XDA Premium 4 mobile app
Click to expand...
Click to collapse
did these exact instructions but the new xparts dosent work so luckily the community had the older version that works,
followed everything buy the book installed cwm using xparts after root went into recovery, wipe data factory reset, wipe cache partition and i even wiped the dalvik cache, flashed the lupus ics+gb kernel booted into the custom lupus recovery (scrolled through the menu a minute) then as expected kernel crash followed by hot boot
any other ideas?
vampyregaming said:
did these exact instructions but the new xparts dosent work so luckily the community had the older version that works,
followed everything buy the book installed cwm using xparts after root went into recovery, wipe data factory reset, wipe cache partition and i even wiped the dalvik cache, flashed the lupus ics+gb kernel booted into the custom lupus recovery (scrolled through the menu a minute) then as expected kernel crash followed by hot boot
any other ideas?
Click to expand...
Click to collapse
Fully working steps:
-download eraser.zip in attachment, unpack it somewhere in pc
-Start flashtool, enter flash mode, hold back button on phone, connect to pc and flash .79 firmware. DO NOT BOOT INTO ROM!
-Disconnect phone and connect again in fastboot mode (hold search button while plugging it back)
-Flash Lupus ICS/Gb 480p or 720p kernel
-While still in fastboot mode, double-click file name "start.bat" from where you unpacked file in attachment.
-Disconnect phone, power on and keep pressing volume down untill you enter recovery
-Install rom and reboot
Bakisha said:
Fully working steps:
-download eraser.zip in attachment, unpack it somewhere in pc
-Start flashtool, enter flash mode, hold back button on phone, connect to pc and flash .79 firmware. DO NOT BOOT INTO ROM!
-Disconnect phone and connect again in fastboot mode (hold search button while plugging it back)
-Flash Lupus ICS/Gb 480p or 720p kernel
-While still in fastboot mode, double-click file name "start.bat" from where you unpacked file in attachment.
-Disconnect phone, power on and keep pressing volume down untill you enter recovery
-Install rom and reboot
Click to expand...
Click to collapse
will try this now hope this one works as were running out of solutions will post again in half hour
Bakisha said:
Fully working steps:
-download eraser.zip in attachment, unpack it somewhere in pc
-Start flashtool, enter flash mode, hold back button on phone, connect to pc and flash .79 firmware. DO NOT BOOT INTO ROM!
-Disconnect phone and connect again in fastboot mode (hold search button while plugging it back)
-Flash Lupus ICS/Gb 480p or 720p kernel
-While still in fastboot mode, double-click file name "start.bat" from where you unpacked file in attachment.
-Disconnect phone, power on and keep pressing volume down untill you enter recovery
-Install rom and reboot
Click to expand...
Click to collapse
followed the instructions to the word kernel still crashes in lupus recovery
vampyregaming said:
followed the instructions to the word kernel still crashes in lupus recovery
Click to expand...
Click to collapse
I don't know what you mean by "kernel still crashed in lupus recovery". In wich step you get that?
Try pressing volume up when powering on to enter twrp recovery
Related
Hello, I did quite a few searches on google and i never found anything similiar to my issue i am having. As the guide says on cm7.. i flashed SEMC 4.0.2.A.0.42 rom with flashtool, no errors or anything. However when i flash CM7.2.0 - FXP105 Kernel the one included in the zip with fastboot... It boots up and i spam the volume button and it brings up the kernel menu, however this is when issues occures for me. It freezes maybe after 20 seconds - 120 seconds, so i am not able to even flash the actual cm7 rom because of the kernel instantly freezing, and sometimes the menu cm7 kernel shows up glitchy just with a few texts. Then i tried to connect my charger to the phone, and now the kernel is glitch free everything works perfect, but as soon as i disconnect the charger the issues comes back
Kernel with update-cm-7.1.0.1 works perfectly but new ones does not? I tried the doomkernel aswell for cm7, and still same issue.
This is how i did it
1. Flashed SEMC 4.0.2.A.0.42 rom with flashtool
2. Flashed CM7 Kernel (the one included in the cm7 zip - fastboot flash boot boot.img)
And i can't go any further than this because the kernel glitches out.
I had a similar problem, try flashing .42 then boot, log in to your Google account and wifi etc., then flash cm7 kernel & rom.
sinkster©
sinkster said:
I had a similar problem, try flashing .42 then boot, log in to your Google account and wifi etc., then flash cm7 kernel & rom.
sinkster©
Click to expand...
Click to collapse
Thanks! It did not solve the problem. Any other suggestions?
Flash with DoomLord Kernel v7 or v4, it actually should runs with all roms.
p47r0n said:
Hello, I did quite a few searches on google and i never found anything similiar to my issue i am having. As the guide says on cm7.. i flashed SEMC 4.0.2.A.0.42 rom with flashtool, no errors or anything. However when i flash CM7.2.0 - FXP105 Kernel the one included in the zip with fastboot... It boots up and i spam the volume button and it brings up the kernel menu, however this is when issues occures for me. It freezes maybe after 20 seconds - 120 seconds, so i am not able to even flash the actual cm7 rom because of the kernel instantly freezing, and sometimes the menu cm7 kernel shows up glitchy just with a few texts. Then i tried to connect my charger to the phone, and now the kernel is glitch free everything works perfect, but as soon as i disconnect the charger the issues comes back
Kernel with update-cm-7.1.0.1 works perfectly but new ones does not? I tried the doomkernel aswell for cm7, and still same issue.
This is how i did it
1. Flashed SEMC 4.0.2.A.0.42 rom with flashtool
2. Flashed CM7 Kernel (the one included in the cm7 zip - fastboot flash boot boot.img)
And i can't go any further than this because the kernel glitches out.
Click to expand...
Click to collapse
did u see fxp logo on bootscreen?
sometimes i had to flashed fxp kernel twice to get it works.
try to flash fresh .42 ftf again..
try to flashing fxp kernel again..
until u have fxp logo on bootscreen..
goodluck mate.
Try This!!
Read my post for solution :
http://forum.xda-developers.com/showpost.php?p=24978172&postcount=752
Use DooMKernel.
You can't change voltage with stock kernel.
but you must have connected to power source every entering to recovery mode.
Enjoy CM7/CM9 based ROM
I unlocked my bootloader via omnius, installed doomkernel and rebooted with no problem, then from recovery did a wipe cache/dalvik and then installed Arconium 8.1
Now i cant get passed the doomkernel startup image, it just freezes there and i have to remove the battery. I also cant access recovery.
Im on baseband 64, had Team Stock Rom installed, and used CWM Auto-Installer 5.0.2.7-nAa-r2. (these were installed while bootloader was locked)
Do you know how to use fast boot? If so I would suggest you use the kernel provided with arconium 8.1 .
Open a cmd window easiest way is to browse to the location where fastoot is located, paste the kernel usually called boot.img in the same folder hold the shift key on your keyboard and press right click and select open command window here. Shut down your phone and then while holding the menu key on your phone plug in the USB cable. Then in the command prompt type fastboot flash boot boot.img
It should show that the kernel was flashed and you can try and start your phone again.
Good luck
Just did that and still it freezes on doomkernel start up image... im desperate
I think the key to the problem is that I had a CWM recovery installed only for stock fw, and I installed arconium on it.
yeah "CWM Auto-Installer 5.0.2.7-nAa-r2" it is!! stock only..
I know that, but what I need is a solution. Im downloading a prerooted .62 fw, is there any other way to solve this without flashing?
Doom kernel should come pre loaded with cwm, but make sure the one ur using is arconium 8.1 because If your using the wrong kernel your phone will not boot.
Just clarify a boot loop is usually a loop of what ever logos repeating over and over so for example if I was having a boot loop in cm9 I would see the freexperia logo than the cm9 logo then freexperia logo again.
http://forum.xda-developers.com/showthread.php?t=1325640
LuckyStriker33 said:
I unlocked my bootloader via omnius, installed doomkernel and rebooted with no problem, then from recovery did a wipe cache/dalvik and then installed Arconium 8.1
Now i cant get passed the doomkernel startup image, it just freezes there and i have to remove the battery. I also cant access recovery.
Im on baseband 64, had Team Stock Rom installed, and used CWM Auto-Installer 5.0.2.7-nAa-r2. (these were installed while bootloader was locked)
Click to expand...
Click to collapse
I had bootloop once while installing CM7..
and i did this...
Boot into recovery mode...WIPE DALVIK CACHE...REBOOT IN RECOVERY...
Delete data/partition....del Cache...REBOOT IN RECOVERY
And then install the zip from SD card....
Lemme know if this helps...
Good day
lol... I had the same exactly the same problem when instaliing arconium 8.1.
I just couldnt find out what to do....
so I just restored a backup using CWM
Kajendran said:
lol... I had the same exactly the same problem when instaliing arconium 8.1.
I just couldnt find out what to do....
so I just restored a backup using CWM
Click to expand...
Click to collapse
The solution I quoted works for 99% of the bootloop issues...
And Kajendran,
I had given the link to download kernel.sin file in the thread started by you...Did it work???
OK, I Know I did a very stupid thing but I flashed the Nordik Version of the Official ICS Rom for Arc S on My Arc.
Now The problem is when it was flashing, the flash stopped at a certain point. Here is the message
14/002/2012 20:02:24 - INFO - Flashing userdata.sin
14/002/2012 20:02:24 - ERROR - Error flashing. Aborted
14/002/2012 20:02:24 - INFO - Now unplug the device and power it on
Click to expand...
Click to collapse
But then After I Rebooted, It showed the sony logo for a second and then some logo of the mobile with a caution symbol (Yellow Exclamatory Mark). And thats it, after a couple of seconds, it switched off.
I repeated the process and the same thing.
Scared Then I Flashed a Doom Kernel and did a factory reset. While the factory reset, it said that it could not open \data :|
i tried formating data many times but it could not mount it saying different file system.
So I flashed a matching Custom ROM and It does not work, Nether is any app installing nor any file getting saved
Please Help!
And Anyway to solve the /userdata filesystem problem?
If flashtool stopped then try re-downloading the file in case it was corrupt, and try to re-flash. If that's not successful download a stock 2.3.4. ftf and flash that.
FTF Wasnt corrupt :\
Now I Have tried flashing the 2.3.4 Android aswell BB 48
A Very old one which I downloaded around december time to root my Arc.
That doesnt even go past the SE Logo
The Custom ROM atleast booted.
My Guess is that the userdata partition has a different filesystem than the one it can read :\
Think it's to do with flashtool being unable to handle ICS data parameters. Binary has posted some type of workaround till he updates it.
Ok, Will check them out.
Thanks!
In his post?
think so, it's mentioned in the thread.
Nope
It stops while flashing the system.sin file
Anyway to solve the /userdata filesystem problem?
Not yet, apparently. I use cm9 so don't really know, though I think there's a cwm flashable ics stock.
sinkster©
No Use of that
Try connecting in fastboot, and use the erase or format commands, e.g. 'fastboot erase boot' or erase system, in case it's a system partition issue
Then try a kernel and rom.
sinkster©
OK, Apparently the problem was that I was using an old version of the flashtool (0.5.8)
I downloaded the latest 0.6.9.1 and followed the 3 step flasshing process
Enjoying ICS on my LT15i
SS4Serebii said:
OK, Apparently the problem was that I was using an old version of the flashtool (0.5.8)
I downloaded the latest 0.6.9.1 and followed the 3 step flasshing process
Enjoying ICS on my LT15i
Click to expand...
Click to collapse
Hi ,
I have ARC S with unlocked boot loader.
I can install any kernel on the phone via fast boot or by using the flashtool latest version.Right now I have installe dthe lupus kernel V16 and I can boot to the CWM and I hae installed the latest version of Ultimate Xperia HD by jader , I can install and after installation if i reboot the phone is stuck at booting screen only. I have tried various kernels and various roms all are giving the same issue.
I can install the ROM but cannot boot it gets stuck at booting screen. I have formatted the partition's via fastboot and by using the CWM still the issue persists.Please help.
Flash the stock firmware ftf file, then try again, or flash a different kernel.
Sent from my Xperia X10 using xda premium
I have tried the same.and it stops and doesn't flash the Rom loading Kernel is very easy, can install Rom too but after this
When I boot it just sits at boot screen
Sent from my iris405 using Tapatalk 2
santsplen said:
I have tried the same.and it stops and doesn't flash the Rom loading Kernel is very easy, can install Rom too but after this
When I boot it just sits at boot screen
Sent from my iris405 using Tapatalk 2
Click to expand...
Click to collapse
Hi guys , Please help me as I have tried multiple kernels and roma all of them exhibit same issue,
Booting to CWM using the CWM inbuilt into the kernel takes a long time as well as once a rom is installed via CWM it completes installation and then comes to the boot screen and it sits at the boooting screena and does not get past it.
How are we gonna help if you don't state ROM and kernel and what exactly you did.
Sent from my Xperia X10 using xda premium
I have installed lupus v 16 kernel , with xperia ultimate hd rom and xperia blue rom both are having same issue.I can boot to cwm and install the rom but after you give reboot after the rom installation it just sits at the boot animation screen .
One thing I noticed is that booting to cwm takes almost a minute after turning on the phone , is this normal ?.
Sent from my iris405 using Tapatalk 2
Did you wipe everything before instaling, and have you tried reflashing th kernel
Sent from my X10i using xda premium
I have wiped system and data ,cache,dalvik cache and have even formatted the partitions from fastboot using fastboot commands ,have even tried rush kernel and u am facing same issue .Please help.
Sent from my iris405 using Tapatalk 2
Good morning,
Yesterday, I tried to unlock and root my friend's Xperia Arc (LT15i). Although it was running FW .62, I did manage to unlock the bootloader and root the phone. I installed CWM, emptied the phone (I thought) and installed the Xperia Ultimate HD ROM.
Unfortunately, I think I forgot a detail. I wiped data/factory reset, cache and Dalvik, but after the installation of the ROM completed succesfully, rebooting the phone keeps it hanging at the Sony Ericsson logo. It seems to be hanging right at that moment, because the problem is that when I then press the Vol.Down button, I'm not getting back into CWM.
I tried to use the "Unbrick" option to flash an original .ftf file via Flashtool, but then I get the "Error in processHeader: 1 Incorrect function".
Can anybody give me a clue on how to:
a) get into CWM
or
b) restore the phone so I can try again
Thanks a lot in advance!
PS: is there a way to get in the bootloader and go to CWM from there? It all seems to be so much more difficult then on my own Nexus S
stalensnuitje said:
Good morning,
Yesterday, I tried to unlock and root my friend's Xperia Arc (LT15i). Although it was running FW .62, I did manage to unlock the bootloader and root the phone. I installed CWM, emptied the phone (I thought) and installed the Xperia Ultimate HD ROM.
Unfortunately, I think I forgot a detail. I wiped data/factory reset, cache and Dalvik, but after the installation of the ROM completed succesfully, rebooting the phone keeps it hanging at the Sony Ericsson logo. It seems to be hanging right at that moment, because the problem is that when I then press the Vol.Down button, I'm not getting back into CWM.
I tried to use the "Unbrick" option to flash an original .ftf file via Flashtool, but then I get the "Error in processHeader: 1 Incorrect function".
Can anybody give me a clue on how to:
a) get into CWM
or
b) restore the phone so I can try again
Thanks a lot in advance!
PS: is there a way to get in the bootloader and go to CWM from there? It all seems to be so much more difficult then on my own Nexus S
Click to expand...
Click to collapse
FW .62 is gingerbread ROM and UHD is ICS ROM.I think you forgot to install ICS kernel. Use the suggested lupus kernel for UHD or any other ICS kernel in Fastboot mod or using flash tool then you can boot into ICS.
shoeseat said:
FW .62 is gingerbread ROM and UHD is ICS ROM.I think you forgot to install ICS kernel. Use the suggested lupus kernel for UHD or any other ICS kernel in Fastboot mod or using flash tool then you can boot into ICS.
Click to expand...
Click to collapse
Oh crap, I didn't even think about that I figured it would be implemented in the ROM. Thanks a lot, I'll try that right away when I get home! :good:
stalensnuitje said:
Oh crap, I didn't even think about that I figured it would be implemented in the ROM. Thanks a lot, I'll try that right away when I get home! :good:
Click to expand...
Click to collapse
Flashing ROM doesn't flash kernel.You need to flash kernel if you are flashing different version of ROM like Gb,ICS,JB. Flash kernel,then go to CWM and flash ROM zip.
I hope someone can help my with this problem...
I had LuPuS v12 GB Kernel
http://forum.xda-developers.com/showthread.php?t=1849536
with Aurora Play 2.0 CRom
http://forum.xda-developers.com/showthread.php?t=2124442
Working just fine, but i decided it was time to change to a ICS based rom... So, I flashed LuPuS v7 Stock ICS/GB kernel
http://forum.xda-developers.com/showthread.php?t=2167766
Using this fastboot guide
http://forum.xda-developers.com/showthread.php?t=2054512
which, btw, was the same I used to flash LuPuS v12 ....
But when I tried to boot in recovery mode (Volume down for CWR, Vol Up for TWRP), the screen just says TWRP for Lupus or CWR for lupus, without any kind of options... If I let the XPLAY boot normally, it just loops en the kernel screen....
I realized that I had to fastboot-erase user data and system... So I did it, and then flash the kernel again, with the same result. Nothing appears in the CWR or TWRP screen....
So I gave up LupusICS and Reflashed Lupusv12 for GB again, using the same method... but I got stuck with the same problem! the screen just loops in the LUPUS screen, and nothing appears in the recovery screen....
I even tried to use this
http://forum.xda-developers.com/showthread.php?t=1493996
to see if I can get to recovery and use the restore option..... I get the FreeXperia Prpject screen, and then black.... NOTHING!
What did I get wrong? Is there a solution to this problem?
Please, help me....
Flash .79 or. 62 firmware with flashtool
Flash lupus kernel (ics or gb - your choise) ( but this time flash kernel with flashtool )
Erase system and data from fastboot
You should be able to boot to recovery.
I can't see what are you doing wrong, but steps above should fix any issues
Sent from my C6502 using xda app-developers app
Thank you
Bakisha said:
Flash .79 or. 62 firmware with flashtool
Flash lupus kernel (ics or gb - your choise) ( but this time flash kernel with flashtool )
Erase system and data from fastboot
You should be able to boot to recovery.
I can't see what are you doing wrong, but steps above should fix any issues
Sent from my C6502 using xda app-developers app
Click to expand...
Click to collapse
Thank you, I did the flashtool magic and it works like a charm... I used a "enhanced" firmware that comes with Auroraplay...
And I'm thinking, MAYBE this is why I got stuck.... MAYBE this firmware is not compatible with ICS Lupus...
Do you know where can I get a clean .79 or .62 firmware?
Edit: I got the clean firmware from here...
http://forum.xda-developers.com/showthread.php?t=1589399
I'm sorry that I asked before looking myself...
The next question (and I've already looked), flashtools asks for a kernel.SIN file.... I've only seen kernel.IMG files
How do I flash the kernel with flashtools?
2nd Edit: NVM, I'm so stupid XD I got the answer to that, too....
BTW, excuse my broken English... this is not my native language....
And again, thank you for your help!