Help!
Phone kept crashing on occasion after an install of BBM for android. An Uninstall and Factory Reset in the settings did not help.
2 days ago it crashed and after powering it back on I get the:
Downloading Do not turn off target !!
&
Could not do normal boot.
ODIN MODE
PRODUCT NAME: SGH-I747M
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: NONE
QUALCOMM SECUREBOOT: ENABLE
I tried flashing back to stock via ODIN 3.6/3.7 but all I get is the below:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I747MVLDMF1_I747MOYCDMF1_1189444_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I've searched but this is as far as I can get
Kies firmware recovery was no help either.
Please Help!
I don't know what you did, but it looks like you need to send it to Samsung. If there isn't a PIT partition, that's bad, and you wouldn't want to mess with those, or you might end up with even worse a brick.
Related
Good afternoon, and thank you for taking your time to read my thread.
I recently attempted to root my phone, and having little to no issue rooting many other devices (including my previous phone, a Galaxy Prevail) I decided I was fed up with the bloatware.
I began the process, but encountered an issue where ODIN failed while attempting to root the device.
I am not 100% sure, but I know this information may very well help me to a solution: I don't think I enabled debug mode in settings.
When attempting to use KIES to restore firmware, I get a "this device is not recognized" error, and even when trying to manually enter S/N and device info, it will not let me use any part of KIES to restore it.
So I then tried to use ODIN to flash stock firmware...
First error I receive is almost immediate:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCDLK3_I747ATTDLK3_I747UCDLK3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
Occasionally, and after about 3 minutes this appears. (and it seems only when attempting to use ODIN on the device multiple times before reboot)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCDLK3_I747ATTDLK3_I747UCDLK3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please, if you have any advice for me I am begging.. I only was able to upgrade to this device because of a promotion AT&T had to get it for $5 dollars.. I am very income restricted so buying a new device is a crippling idea. If you do by chance suggest I download a new version of ODIN ( I am using 3.07, I find it most stable) or a new stock firmware etc, please provide links as I have attempted many different mirrors (with horrendous download speeds) for different stock recovery firmware.
THANK YOU!!!
I appreciate your time.. All it took was attempting to root the phone another time to restore access... Wow.. I hate myself ._.
Vonzilla said:
I appreciate your time.. All it took was attempting to root the phone another time to restore access... Wow.. I hate myself ._.
Click to expand...
Click to collapse
So, what's the state of the phone now and what happens when you try to power on? Is it now booting normally to system?
My phone randomly stopped working the other day. When its off, it'll start up on its own (without the power button being touched) but only get past the "samsung" screen a couple times and then shut back off. I tried flashing the stock firmware via odin but it fails every time (I've used versions 1.86, 3.04 and 3.09). As of now, my phone is totally useless. All I can do is put it into download mode. Any ideas?
This is what odin says every time
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCALG1_I747ATTALG1_I747UCALG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Phone Screen:
ODIN MODE
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 0
BOOTLOADER AP SWREV: 3
SW REV CHECK FAIL : Fused 3 > Binary 0
Odon is failing because you are trying to downgrade the firmware. After 4.3 you cannot do this anymore. It looks like you probably updated to 4.4.2 via ota. Correct? If so there is no firmware you can flash as att refuses to release it.
Take your battery out and put it back in. If it tries to turn on by itself your power switch is bad and needs replacing.
Sent from my SAMSUNG-SGH-T999 using Tapatalk
Hello, i have one piece n7100 16gb that was stuck on repair mode...i tried to repair it with odin on windows 10 detected the device but fail: Used Odin3_v3.10.7 and N7100XXUFNL1_N7100OJVFOD1_LYS
Tried on windows xp still fail same..
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Tried flashing with 16gb pit file...fail now when turn on phone shows grey screen but goes into download mode....help
andrew21 said:
Hello, i have one piece n7100 16gb that was stuck on repair mode...i tried to repair it with odin on windows 10 detected the device but fail: Used Odin3_v3.10.7 and N7100XXUFNL1_N7100OJVFOD1_LYS
Tried on windows xp still fail same..
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Tried flashing with 16gb pit file...fail now when turn on phone shows grey screen but goes into download mode....help
Click to expand...
Click to collapse
search for note 2 partition problem, there are multiple guidea on xda. keep trying with different versions of odin and roms from sammobile
yaro666 said:
search for note 2 partition problem, there are multiple guidea on xda. keep trying with different versions of odin and roms from sammobile
Click to expand...
Click to collapse
Hello, when i go into download mode i get following info:
Product Name: GT-N7100
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Custom
KNOX WARRANTY VOID: 0
RP SWREV:
ALso, i tried flashing 4 files with odin, i get following log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_OJV_N7100OJVDMB1_679347_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
i forgot to mention i flashed only the folllowing pit file: PIT_N7100_16GB_20121102 with Odin3_v3.10.7 after which i get grey screen when i switch on the mobile, but i can still go into download mode....pleeeeaaasssee help
Also need to inform im using windows 10 but with correct drivers and connects with odin.
Cant anyone please help me...tried different roms and firmware still same problem...
I believe the eMMC chip has failed. The same happened to my phone and the service guy said i needed a new motherboard.
Some say it may also be a corrupted bootloader, which i have had no luck in fixing.
Wish i could help
It's ok thanks for informing me at least
Love to hear if you get it up and running again
I would love that too but don't have any solutions at the moment
so i just want to tell you what all happened exactly..
my phone was kept on charging and after i unplugged it .. it did not start..
so i tried researching and find out solutions..
one possible solution i found out was to flash the STOCK FIRMWARE using ODIN..
but when i entered the download mode and i started flashing the stock firmware i am facing this issue
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUFNL1_N7100ODDFNI1_N7100DDUFND1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
need HELP ON HOW TO FIX THIS PROBLEM :| :crying:
Did you try different USB cables and USB ports?
Using Unofficial LineageOS 14.1 (v2awifi). During using my Tab Pro 12.2 SM-T900 I got a failure and switched off my tablet. Since that time I can't start my tablet. Can only turn on my tablet in downloadmode. Can't enter recovery. Tried to flash TWRP, but that is not possible. Because the failure was suddenly, I could not and can't switch and change usb-debugging and media-transfer possiblities.
I tried to install Stock Rom with Odin, got the next faillures:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
And sometimes:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
So I can't flash the stock rom for repairing my ROM. Please help me, so that I can use my tablet again. How to fix PIT-partion ?
I have the same problem. Any resolution?
Same but on an SM-T320. Flashed an appropriate PIT, stock firmware...nothing working. I'm thinking it's a physical issue at this point.