Hi everyone!
I opened my xperia s, and I accidentally cut the cable which is connected to the led bar board, and now my screen is not turning on, and the vibration doesn't work and the led bar also doesn't work.
What should I do?
Thank in advance!
Sorry for my English
It's a hardware (physical) problem.
I assume you soldered the cable or tied it back?
In any case, the problem is not software, you should go to a repair shop or the phone company if you have warranty
Related
Hello,
It seems that flat cable which connects the slide-out screen is broken: the touch-screen doesn't work, and there's a white lines all over the screen while opening the device.
I've made a call to my local service center and they said that I need to change the whole touch screen because the cable is glued to it.
Is it right? Is there another way to fix the device rather paying $300 for a new screen?
i have also the same problem For my PDA2K , my flat cable which is comming from the screen under the slider is broken ,, half of the cable , i have the orange cable ,, is there any way to fix it
Thanks
I just bought this Xperia, works 100% with the screen opened, I close it and screen cuts out, but is still running, and reopening screen stays off. Is this possibly just the cable betwwn top and bottom faulty?? Anyone had this before?
kro02 said:
I just bought this Xperia, works 100% with the screen opened, I close it and screen cuts out, but is still running, and reopening screen stays off. Is this possibly just the cable betwwn top and bottom faulty?? Anyone had this before?
Click to expand...
Click to collapse
Yep, this has happened to me too. Its definitely the flex cable. The flex cable is the ribbon which connects the motherboard to the screen itself on the slider action. If you think you have warranty send it straight to warranty and they will probably repair it for you. If not, you can buy a full flex cable repair kit specifically tailored for Xperia Play on Amazon or Ebay. However, you do need some basic hardware knowledge to do this operation yourself.
Recently, I disassembled my Sony Ericsson Xperia Play R800at. I was replacing the housing and digitizer. All went smoothly until I missed an important step. There was a black tab that holds down the flex cable that connects to the digitizer. I forgot that step and my flex cable ripped.I have ordered another as a replacement. I understand that this will cause the digitizer to not work, but I have more issues, and I want to know if they are due to the missing cable.(the ripped flex cable.) I assembled the phone and the screen functions normally. As to be expected, I can't interact with the screen. However, Now my search button and settings buttons aren't functioning. My home and back buttons are working although. Also, My phone will not charge anymore. Is this due to the missing flex cable? I hope I didn't accidentally screw anything up. I was really careful, so I don't know why they won't function. I really hope that these issues are due to the missing cable. :silly:
Sorry, I am not allowed to post links.It has the camera and earpiece on it and is attached to the slider. :"(
How. Could u miss a step itsm really easy to take apart and put together its the flex cable garunteed
Sent from my Sony Tablet S using xda app-developers app
Tutorials
Most of the tutorials seem to be only of disassembly. Little to none are of reassembly. I wrote down a list and reversed the order, but as it got closer to assembly, I started to assemble it myself. Big mistake. I assumed the black tab was only there to hide the chips.
Charge Recognition
It actually can charge, but only when the phone is powered of. This must be due to the missing components. Maybe because some parts of the phone aren't connected, the phone will not recognize the charger when powered on. What a relief...:angel:
Just watch dissassembly in reverse
Sent from my Sony Tablet S using xda app-developers app
I got the replacement part. I even replaced the slider. I transferred the button cable to the new slider along with the main flex cable and the camera/earpiece flex cable. I am confused. I am inserting the flex cable into the digitizer slot, but it isn't working. I assumed there was a lock mechanism of some sort, but still no luck. I am not sure why it isn't going all the way in. Reversing the steps just isn't working. Placing the flex cable in is way harder than taking it out. Is there a certain way to place this cable in. What I am in need of is a picture of how a functioning digitizer's attachments look. Are you supposed to be able to see the golden tip of the flex cable?(Again, I am speaking of the flex cable with the black tab covering it. It is very small.)
:crying:
Lock.
There were locks for just aboul all the ZIF Connectors. Sony Ericsson's manual is the best!:good:
I tried again using the locks on the slots but it still wont work. Even with the manual, no luck... Now, it is charging normally, even while on. This indicates that something has changed. I wonder why the digitizer isn't working though. Maybe I should see what happens If I revert back to my old digitizer...
Hi all,
I just replaced the flat cable of the phone, the one that connects the two phones parts together. The phone was having issues with the display when going to landscape-mode and the mic stopped working recently so I replaced it following this guide:
Anyway the display problem is solved by replacing the faulty flat cable but only a new problem occured.. The screen does not respond including the capacative buttons and the big scroll button, its looks like the whole display unit with all its buttons is not working. Any suggestions? I will be taking it apart again and check if all cables are well suited but besides that someone might recognizes the problem
Thanks in advance!
Could be bad connections, the new cable you put in could be bad or by coincedence the digitizer went
Sent from my HTC Vision using xda premium
Hi
Some time ago i had custom rom on my Xperia Play, but flex cable from screen died and i replaced it.
After that, my phone freezed on Lupud kernel logo, vibrate and nothing more. No recovery etc.
Today i flashed it through flashtool to stock rom, and it started, logo "sony ericsson" pop up and after few minutes it dissapeared.
Now if i push power button i se some "snow, mozaic" on screen.
I don't really know what do next. I thought it's kernel compatibility problem, but know it look like damaged flex cable.
But kernel logo looks perfectly, only on rom something is broken.
I will appreciate any help.
IMHO, i think it's flex cable again.
I had also had similar problem.
1st and 2nd flex replacement went without problem
3rd was just black screen. It did vibrate, but nothing was on screen.
4th was half working (it show/stay on lupus logo and 1 in 10 tries it boot into rom but without touchscreen working)
5th was working on first try
It is hit&miss logic. Maybe it's problem with crappy quality, maybe it is problem with zif connectors on slider flex cable.
Try your flex cable again, but this time, first insert flex cable that goes from front camera/proximity sensor into zif connector of slider flex cable, and see how much actually is "good connection". Then press slider flex cable into possition and compare to your previous observation. If it's even 1/2 of mm away, it could be bad connection (flex from camera is not inserted fully in zif connector). Best position to be sure is that front camera flex have a very small "belly" (curved shape).
It looks like your 4th cable. I will try mounting it few times and order new one.
Now i realized, that "snow/mozaic" shows after screen shut down to save energy.
P.S.
For those from the future which will looking for solution for problem similar to mine.
Yes, it worked. Flex cable can work and don't in the same time.