Hi,
Don't know if anyone else has experienced this problem. I bought a HOX as a second phone to mess with and possibly develop on (have another HOX as main phone). was cheap as someone had put hole in battery trying to pull apart so didn't expect it to work. Long story short new batt and worked fine, unlocked bootloader, flashed CWM, backed up original HTC Rom, flashed viper x 4.0.0 no worries. Then a friend broke her HOX screen, told her she could have mine and checked with my supplier which LCD/Digitizer was compatible ( supplier came back with sharp screen).
Had a spare one lying around so put it in and "woke up phone" - only home screen lights worked so put my original screen back in and "woke up phone again" - same problem so put sharp screen in and rebooted phone - still no display, once booted swapped screens and woke up phone again and got display- until phone went to sleep again and now cant get any display at all. Everything else works as per normal except no display.
Can lock/unlock bootloader, flash stock recovery and CWM, using my good phone as a template to navigate CWM I think I even managed to restore original HTC Rom. Lock screen can be unlocked and PC will see the SD extension, charge etc.
HELP has anyone had this problem. Have tried Heating chips/cleaning/putting in freezer as another post had had success with but still same problem.
Looks like a mainboard problem to me. Have had it also, first they replaced the screen, with no result.
webpatrick said:
Looks like a mainboard problem to me. Have had it also, first they replaced the screen, with no result.
Click to expand...
Click to collapse
That's what I'm starting to think the problem is.
Thanks for the response.
looks like I have an expensive flash drive now.
Related
Hello everyone,
Basically went to unlock my phone today and touch screen is not responding, however the hardware buttons work fine. Now i've done some research and found other posts of people with the same problem, however their touchscreen problems seem to be fixed(temporarily, at least) with a battery pull.. mine however is still unresponsive after half a day and multiple battery pulls.
Id rather not have to send in for certified to replace an otherwise perfectly working phone.
Any ideas/suggestions would be greatly appreciated!
bigdeezer20 said:
Hello everyone,
Basically went to unlock my phone today and touch screen is not responding, however the hardware buttons work fine. Now i've done some research and found other posts of people with the same problem, however their touchscreen problems seem to be fixed(temporarily, at least) with a battery pull.. mine however is still unresponsive after half a day and multiple battery pulls.
Id rather not have to send in for certified to replace an otherwise perfectly working phone.
Any ideas/suggestions would be greatly appreciated!
Click to expand...
Click to collapse
are u undervolting?
Nope, sorry forgot to say. Completely stock never unlocked or rooted.
Also i tried getting into recovery to try and do a factory reset but when i select recovery i just get the android on his back with the red triangle..
so instead i just went through the steps and unlocked the bootloader and booted up (in order to give me the factory reset without having to touch the screen)
It unlocked and booted up fine but still no response..
No new recent app installed and never had this happen before.
Mine did this after a few days of owning it, and luckily the store took it back and swapped it out with a perfectly working unit. Is yours within a few weeks of purchase?
Figured this out randomly. Remove battery cover. With phone turned on, press on the area to the to the left of the camera lens until the screen is responsive. My screen becomes unresponsive when the phone is dropped and this fixes it.
dailong said:
Figured this out randomly. Remove battery cover. With phone turned on, press on the area to the to the left of the camera lens until the screen is responsive. My screen becomes unresponsive when the phone is dropped and this fixes it.
Click to expand...
Click to collapse
hrmm this does not seem to fix either. I also have never dropped my phone, although this seems to be worrisome if the issue is hardware related.
@ tmellen i purchased the phone from amazon and am a few days past my return date :-/
Guess ill just give them a call and hope for the best. Thanks for the ideas everyone.
(update) called amazon and they are sending me a brand new phone.
Knowing this i thought i'd try dailong's method again only this time i was quite a bit more "rough" with pressing down on that area, and it actually worked!
Ill still be taking the new phone once it gets here but for anyone who is having this problem there's a sweet spot on the left edge of the phone towards the top (looking at it with the back cover off) there should be a circle shape. press on that area really hard and it should fix.. weird
Experienced the same on my GSM version a few minutes ago. I had to call my mobile to get it to respond. After that it worked again as normal. I'll see if I get this issue again in the next few days. Hope it's just random
Had the same happen earlier to mine and I was on AOKP. I've had this happen to other phone before, shouldn't be a a cause for alarm unless it happens very frequently. Btw, next time it happens to me I'll give that left side of the camera trick a try.
mine got fixed by removing battery.
Hi all,
Since yesterday, I've noticed that my Desire won't always turn on the screen when I push the power button if the phone is locked. The hardware keyboard lights do turn on (depending on light levels of course) but the screen stays black.
It does turn on now and again, but I haven't found a clear pattern yet.
Also, the screen works normally when I pull the battery and start the phone again.
It might be worthwhile to know, last friday my sdcard died on me, so I bought a new one (Sandisk 8GB class 4). Also, last saturday evening I managed to destroy the AMOLED screen, and yesterday I put in a new one. I did not encounter the problem before my screen broke.
Obviously, I have googled the problem, mainly getting hits for androidforums.com. Possible solutions there were: SD-card is borked; try reformatting, a contact is loose in your phone; try opening up your phone and reconnecting everything, and that the proximity sensor might be blocked.
Did all three of those things, made sure that the two holes in front of the sensor were clear of dust etc., but no improvement.
Basically, it's really annoying, and if someone has any input, I'd appreciate it a lot!
Forgot to mention, the rom I'm using at the moment is MIUI-Au v2.4.3, was running Sandvold's ICS Beta 0.6.0 yesterday, had the same issue.
Thanks in advance,
plinders
Have the same issue with Sandvold's ICS ROM 0.6 and lower.
When i pull the battery off it's all ok.
Just confirming that the proximity sensor is working properly, I made a call today and the screen turned off as I was holding it to my ear. After I finished the call, the screen stayed off.
I'm going to reinstall the RUU (Starting at the Froyo RUU and installing GingerBread afterwards, to make sure any trace of rooting has been removed just in case), to see if there's any improvement.
I've also read that the problem might be caused by a condensator which has been knocked loose (could well be an option in my case), but I wouldn't have any idea where that condensator would be located.
Thoughts?
Okay, reflashing the RUUs didn't improve it.
Does anyone have any ideas what I can do now? I'm not going to buy a new phone, my budget doesn't reach that far and I only have my Desire for half a year.
So, I located the cap mentioned at http://androidforums.com/desire-sup...screen-but-phone-still-hardware-software.html but that was still fully intact. I did notice that, for my feeling, the digitizer board was a little too close to the caps of the screen. So I reseated the board, put the phone back together and.....
It worked!
Hi there,i have a Extremely Huge Problem D:
My Htx One x Just does Nothing not even shows me the Charge Led it is Completely Dead.
I Used the Leedroid 6.2.0 Rom and Installed it Exactly how the Tutorials etc Told me,and i am not a Flashnoob.
It worked Perfectly,i came Home Looked at the Time on the Phone,then Got Back in my Livingroom,and Dead..... Nothing
What happened,i cant enter Recovery,The Powerbutton dont does something.
The Phone is a Week Old
Okay it Booted again.
What could be the Issue?
Is there a Way to Completely Relock the Bootloader and Send it Back ?
Because i think i just have on of those Faulty HOX
Sometimes a Cracking Sound over the Speaker in games Etc
Lower right Corner of the Screen Cracks Really Bad even when i Gently (Touch) the Screen.
Also these well Known problems with the Colors when i Touch the Edges of the Screen
Skolotaie said:
Hi there,i have a Extremely Huge Problem D:
My Htx One x Just does Nothing not even shows me the Charge Led it is Completely Dead.
I Used the Leedroid 6.2.0 Rom and Installed it Exactly how the Tutorials etc Told me,and i am not a Flashnoob.
It worked Perfectly,i came Home Looked at the Time on the Phone,then Got Back in my Livingroom,and Dead..... Nothing
What happened,i cant enter Recovery,The Powerbutton dont does something.
The Phone is a Week Old
Okay it Booted again.
What could be the Issue?
Is there a Way to Completely Relock the Bootloader and Send it Back ?
Because i think i just have on of those Faulty HOX
Sometimes a Cracking Sound over the Speaker in games Etc
Lower right Corner of the Screen Cracks Really Bad even when i Gently (Touch) the Screen.
Also these well Known problems with the Colors when i Touch the Edges of the Screen
Click to expand...
Click to collapse
unlocking the bootloader voids your warranty so you will have to pay for any repair costs, just a heads up
Dear community.
A few weeks ago I rooted my LG G3 and installed Fulmics 6.0.
Everything went as planned and worked seemlessly.
Today, while watching YT-videos my device turned off and tried to reeboot. After the first, non-animated LG screen, the blue screen appeared.
Same to say while trying to boot into TWRP recovery. After the blue TeamWin Startscreen, the blue screen shows up again. :crying:
Is there any help left?
Kind regards
Thomas
My friend also happen problem
He asked people to help take
Finally, open the motherboard
Then take heat
That seems to be a common problem LG G3
Welding where welding is not good
PS. I use google translate
hi guys, i had the same problem now for 2 days searching the forums for any sign of hope even ringing lg them selves to for them to tell me the repairs will cost more than the phone
so i new at this point i had nothing to lose.. after playing around for 13 hours with my phone i have got it all up and running at the minute for a full day an not once gone off so i might be the lucky one buts its worth a shot
this is what i did.
disassembled my lg g3 and took out the logic board
took off both heat i/o sheilds from the i/o
with a fine tooth brush and some contact cleaner (ipa 90%) i cleaned the main part of the board and let it dry out half hour
i then applied hot air onto the board both sides and let the contacts reseat them selves and the put phone back together (make sure you out the i/o shields back on)
i then tried resetting my phone with lg flash tools and the correct fireware for my phone
(when you are cleaning your phone there is a little sticker on the chip stating what firmware you phone came with, find this firm where as you know it will work)
anyways it didnt work for some random reason so i tried lg flash tools 2014 (i will link everything below).
so when i found the correctish .kdz file i flash the firmware making sure everything went
and for the first time it went to 100% first time.
played with my phone for a while all seamed ok wasnt the standard firmware what was on when cam out the factory.
so i then tried lg flash tools again with the correct firmware and it worked spot-on and has never played up are missed a beat since....
everything i used:
lg flash tools 2014= http://forum.xda-developers.com/showthread.php?t=2797190
lg flash-tools and lg drivers= http://lg-firmware-rom.com/lg-tools-software/lg-flash-tools-flashing-lg-tot-stock-firmware/
firmware's = http://storagecow.eu/index.php?dir=Xda/LG+G3/Stock/D855/
Novamatic Mike said:
hi guys, i had the same problem now for 2 days searching the forums for any sign of hope even ringing lg them selves to for them to tell me the repairs will cost more than the phone
so i new at this point i had nothing to lose.. after playing around for 13 hours with my phone i have got it all up and running at the minute for a full day an not once gone off so i might be the lucky one buts its worth a shot
this is what i did.
disassembled my lg g3 and took out the logic board
took off both heat i/o sheilds from the i/o
with a fine tooth brush and some contact cleaner (ipa 90%) i cleaned the main part of the board and let it dry out half hour
i then applied hot air onto the board both sides and let the contacts reseat them selves and the put phone back together (make sure you out the i/o shields back on)
i then tried resetting my phone with lg flash tools and the correct fireware for my phone
(when you are cleaning your phone there is a little sticker on the chip stating what firmware you phone came with, find this firm where as you know it will work)
anyways it didnt work for some random reason so i tried lg flash tools 2014 (i will link everything below).
so when i found the correctish .kdz file i flash the firmware making sure everything went
and for the first time it went to 100% first time.
played with my phone for a while all seamed ok wasnt the standard firmware what was on when cam out the factory.
so i then tried lg flash tools again with the correct firmware and it worked spot-on and has never played up are missed a beat since....
everything i used:
lg flash tools 2014= http://forum.xda-developers.com/showthread.php?t=2797190
lg flash-tools and lg drivers= http://lg-firmware-rom.com/lg-tools-software/lg-flash-tools-flashing-lg-tot-stock-firmware/
firmware's = http://storagecow.eu/index.php?dir=Xda/LG+G3/Stock/D855/
Click to expand...
Click to collapse
Just an quick update the phone is still working like a dream. Also upgraded to lasted OS. So this could of been a lucky fix or just a bad section in software.
Sent from my LG-D855 using XDA-Developers mobile app
I actually just got this yesterday, and fixed it. It started blue-screening and rebooting sporadically but quickly got to the point where I'd turn the phone on and it would blue-screen and shut off after two seconds. I could still hold Vol Down and power to get into the STOCK system recovery screen, and by choosing Safe mode (Factory data reset went to blue-screen) it went into TWRP. I tried a whole bunch of different things (and luckily was able to get a backup of the internal storage to my SD card) before doing a full wipe. FULL wipe. I then flashed the stock image via KDZ which is where I sit right now. No blue-screens. I had been on Jasmine 9.1 and Skydragon kernel, I'm thinking maybe a recent update didn't play nicely with either of those, or maybe some other custom firmwares too.
I also got this and somehow i manage to resurrect the phone. I was installing another stock-based ROM (Zoe ROM 3.0 - based on V30N) and after setup my phone got a blue screen. I unplugged the battery, i tried to start it again but only showed LG logo for one second, and after that was dead. I mean, completely dead. No power, no charging, no PC detection, nada!
What I've done:
1. disassembled the phone and pull out the motherboard (G3 is really easy to disassemble, really);
2. open the protective cover near the CPU/Memory (it's a weak metal cover, easy to pull down);
3. i wiped gently with a toothbrush and alcohol all the components (i put a lot of medicinal alcohol);
4. i used a hair drawer (hot) to clean the excess of alcohol and to heat the CPU zone (about 1-2 min);
5. i assembled all back together and i prayed to God (no joke, believe it or not);
6. after that i pressed the power button + vol- (to enter recovery) ... and surprise, it's alive;
7. i restored a anterior software backup, just in case... (now i use Zoe ROM 2.7 based on V30J);
Now it's working for about ~4 hrs and no problem at all... i will edit this if something is happening.
Good look! And pray... sometime it really helps.
FusionGFX said:
Dear community.
A few weeks ago I rooted my LG G3 and installed Fulmics 6.0.
Everything went as planned and worked seemlessly.
Today, while watching YT-videos my device turned off and tried to reeboot. After the first, non-animated LG screen, the blue screen appeared.
Same to say while trying to boot into TWRP recovery. After the blue TeamWin Startscreen, the blue screen shows up again. :crying:
Is there any help left?
Kind regards
Thomas
Click to expand...
Click to collapse
I'd suggest flashing an original factory image and re-rooting / re-installing TWRP.
Worked for me also !!! Without praying
Novamatic Mike said:
hi guys, i had the same problem now for 2 days searching the forums for any sign of hope even ringing lg them selves to for them to tell me the repairs will cost more than the phone
so i new at this point i had nothing to lose.. after playing around for 13 hours with my phone i have got it all up and running at the minute for a full day an not once gone off so i might be the lucky one buts its worth a shot
this is what i did.
disassembled my lg g3 and took out the logic board
took off both heat i/o sheilds from the i/o
with a fine tooth brush and some contact cleaner (ipa 90%) i cleaned the main part of the board and let it dry out half hour
i then applied hot air onto the board both sides and let the contacts reseat them selves and the put phone back together (make sure you out the i/o shields back on)
Click to expand...
Click to collapse
This worked for me! Didn't even need to reset the OS. My wife's G3 shut down on her one day. I started trying to fix it, but couldn't get past it showing blue screen, boot looping, and then going dead to the point where it wouldn't even boot to the flash recovery screen. I couldn't even get it to turn on at all until I took the battery out and held the power button down for 20 sec.
Then I read this post, removed the circuit board and shields on both sides, blow dried on hot/low setting for about 7 min each side, and let it cool off for about 10 min, then re-assembled everything. First boot it went right to the PIN lock screen like normal. So far so good it's been running for about 30 min no issues. Thank you!
Glad it's working mate I got my phone to my little one now and still going strong it did have a little TIFF a few weeks ago with not even turning on but left on charge for a day as for some reason the battery drained that much it couldn't even charge so yeah
Yeah just did a drop test and smacked it around a little, so far so good still going...
I have a solution to this problem.
When you disassembly phone and remove protective cover (from processor site) remove little battery from motherboard - near to processor.
Thats all. G3 is back to live (at least mine)
The bsod happened to me as well. After trying everything, flash stock firmware, boot to recovery and wipe data, cache etc and nothing worked. I then disassembled the phone and put the motherboard in the oven at 180degree for 10 minutes. So far so good, it booted up fine and it's working pretty well till now. Flahed v30b version and it's working since 10 hours. Will report back how long it stay alive eheh
Sent from my LG-D855 using XDA Labs
Looks like this disassambling things really works cuz i read so many places and heard from friends that it works.
But really strange why it suddenly started this problem on everybody
I solved the problem by putting CPU limit. It is not a good solution while your phone works as half of its potantial but it works. Maybe one day i will bake it too
Here's another proof that the heatgun solution seems to work.
My G3 was randomly crashing from time to time over last month but the bluescreen appeared for the first time today. Since then it didn't make it past the LG logo before it would turn blue and shut itself of. So same problem as described above.
I took it apart and took of the metal "heatspreaders" from the motherboard, then heatgunned it from both sides for like two minutes each (with waving the heatgun around so I wouldn't burn the entire thing ), let it cool down a little and reassembled it.
I then just powered it up normally and it works just fine.
I'll update you in a few days.
KaiTech96 said:
Here's another proof that the heatgun solution seems to work.
Click to expand...
Click to collapse
Yeah, it works, in most cases. The question is - for how long... You may be lucky, and it could be a permanent fix for you. However, the nature of the issue is a manufacturing defect which can only be fixed for sure by reballing the chip (or by just replacing the whole board). Going a bit deeper into technical details, the chip in question is a BGA type (Ball Grid Array). It means that it doesn't have traditional leads for soldering on the board (the ones that are either sticking out or just located on the sides). Instead, it has soldering pads on the underside, and the soldering is done by putting a pre-arranged set of solder balls (hence the name), and the flux on the pads, and then heating up the assembly until it melts. A flaw in preparation or in the soldering process itself results in a bad contact on some pads which usually manifests itself either after the chip and board heat up under load, or when the board is physically deformed even a tiny bit (hit or dropped), or just after some deterioration/oxidation over time...
Sorry for the nerdy stuff, I am done now... Basically, consider the heatgun trick to be about the same as banging on the side of the old tube TV trying to fix the static on the screen...
The battery on my HTC 10 was completely shot and needed to be replaced. I'm a careful person by nature and this being my first phone repair, I bought an extra screen just in case something happened getting it apart. Followed a guide by jerryrigeverything on how to take apart the phone, got the battery replaced, everything seemed to go smoothly. When I went to test the display before screwing everything together, the new screen I installed lit up, but the right half of the display only showed as a repeating segment from the middle of the screen. Thinking the connector was loose, I disconnected and reconnected the display and made sure everything was tight: same problem. I reinstalled the original display, which I made sure had worked after cutting through the adhesive before I disconnected it, and now the old display is also showing the same issue.
The touch screen on the broken side of the display still works, I'm able to type PIN numbers and whatnot even though I can't see them properly. Only thing I can think of is maybe the connection actually got some debris or something inside of it? I don't think I damaged anything, as I was super careful, but it was also my first time opening up a phone.
Sorry for the inefficiently worded post. Any help would be really appreciated.
Did you resolve this?
I have exactly the same issue you describe after my screen replacement (with two new screens) Believing the first was a dud.
I have done many screens/batteries on my m7, m8's previously never having a problem.
I'm currently back to running my M8 and miss my 10!
Anyone reading this and has any suggestions they are all welcome!!
Thank you in advance
Exactly the same issue this guy has
https://youtu.be/RpdCuMiTOn8
I'm now wondering if it is just bad aftermarket screens?
Has anyone else replaced their screen successfully, if so where did you get the screen?
Thanks Rory
I have been having the same problem. I just tested screen number 4 that has the same exact problem. Is there a specific brand that is known to test well?
I dropped my 10 in water at work...believe it was a salty water at that. It stopped working completely. I opened the phone to check the internal components for damage and I broke the LCD doing so. I replaced the battery and the screen at almost the same time. I think it may have been a week or two apart.
The battery is still working. The screen worked initially but the phone kept getting really hot and the heat kills the phone. I tried keeping it cool at all times which kept it operational. It hasn't been activated since I quickly replaced the phone with another of my lines upgrades. I went back to the phone to check it out and try using it as a replacement for my daughter but the screen no longer works.
The battery charges just fine...the led light indicates that well. I've tried reinstalling it several times with no success getting the screen working again. I tried the original screen to check and I could see light and it was responding but its not usable so I'm stuck with a phone that has a new non-working display. I think the brand was called DIYRepair or similar.
If anyone has encountered this and has advice...I'd be happy to try anything.