Develop Bugs

Kindle Fire is stuck at boot screen, (no animation). Help!

Hello Everyone,
I will try to provide as much details as I can from what I remember.
Basically, I tried to ROOT my device and install TWRP. However, I messed it up the first time. I tinkered with it for hours but it still couldn't work until finally, after hard resetting for the unlimited time, it booted up.
The problem though, is that it wasn't rooted and TWRP wasn't installed when it came up so I tried it again. Second try, second time it was messed up. Annoyingly, I don't know what I did earlier to make it work. The second instance it happened is just like the first.
Just to be clear, this isn't the boot screen where the kindle fire logo is animated (has reflections). In my case, its the logo as is, stuck on the screen just like that. Tried hard resetting, doesn't work.
What do I know?
1) From my earlier experience, it has lesser to do with the system (PC, Mac) and drivers since I managed to get it boot up again without being connected the first time
2) If I do connect it to the PC, it says Cannot Start Device/Unable to Start Device. Code:10. That's it. Even if I reboot the device, its still the same.
3) If you connect it to the Mac, it is detected in system preferences. Problem though is that I tried using adb and just like its windows counterpart, there are no devices detected.
THOUHGTS:
1) I know I just have to get it to be recognized and I can change the bootmode. Something's telling me that its a boot mode problem only. In my earlier V3X phone, I used to TP (testpoint) if anyone's familiar with that, or shortcircuit the board to get it out of the 'loop'. Do we have that with the kindle fire?
2) What operating system would it be easiest to get the device detected. I'm hoping that if there's lesser complications with the device being detected by the computer, be it mac, linux or windows, I can change the bootmode. my technical instinct tells me it has something to do with boot mode.
What have I done already?
1. Let me see, I believe I tried hard resetting it for ALOT of times already
2. Reinstalled drivers on PC. Used both Android and Kindle Fire Utility drivers. Even checked the /android folder
3. I'm using a Nokia Micro-USB cable. I'm not sure if that has any impact on the device or its effectiveness but I will try to pick-up another cable today and post later.
I would really appreciate if anyone can help. It sucks that I tried this just after unboxing the unit. I haven't even tried doing anything on it yet.
If you can help, ANY help would be appreciated.
Thanks mate!

had the same
1. use computer (windows - in my case windows xp)
2. nokia cable is fine (i use it too)
3. use kf utility .6
is your kf recognized by the computer ? (adb device or composite adm device)
have you tried to shutdown and startup your computer ? (not restart)
the entry for 18D1 in adb_usb.ini is missing - had to add it
the other entries are allready in version .6 android_winusb.inf
if you have troubles to remove old drivers use this:
http://support.microsoft.com/kb/315539/en-us
unplug/replug and install the drivers from .6 from scratch
it's not needed to reboot the computer - works immediately
waiting to get your status ...

b63 said:
had the same
1. use computer (windows - in my case windows xp)
2. nokia cable is fine (i use it too)
3. use kf utility .6
is your kf recognized by the computer ? (adb device or composite adm device)
have you tried to shutdown and startup your computer ? (not restart)
waiting to get your status ...
Click to expand...
Click to collapse
Did you solve your problem?
My kindle is recognized by my computer but it as either ADB device or Composite ADB device (depending on what drivers I use to install it). Problem is that it says Cannot start device. Code Error: 10. Tried shutting down/restarting PC, still the same.

updated my initial post again ... (ms-link)
yes solved it in minutes
make the additional entry in adb_usb.ini
use only the drivers from .6
i think best way is to disconnect the kf - uninstall all old drivers regarding adb device - connect kf - use only drivers from .6 utility - start utility - change bootmode - up again !
whats your status ?

i think best way is to disconnect the kf - uninstall all old drivers regarding adb device - connect kf - use only drivers from .6 utility - start utility - change bootmode - up again !
Click to expand...
Click to collapse
I did this but it still says device cannot be started.
make the additional entry in adb_usb.ini
Click to expand...
Click to collapse
0x18D1 -- is that what I'm supposed to add to adb_usb.ini?

yes exactly - the device changes between the two id's regarding the bootmode
and don't let the computer select the driver - select manually

b63 said:
yes exactly - the device changes between the two id's regarding the bootmode
and don't let the computer select the driver - select manually
Click to expand...
Click to collapse
Okay, so I followed the instructions to a T.
I followed the MS Link to remove all drivers and then plugged-in the kindle and installed it back again by specifically telling windows that 'I have a disk'. It still says Code 10.
If it would mean anything, I'm doing this on a virtual machine since the computers around me are all Windows 7s.

kaswistry said:
Okay, so I followed the instructions to a T.
I followed the MS Link to remove all drivers and then plugged-in the kindle and installed it back again by specifically telling windows that 'I have a disk'. It still says Code 10.
If it would mean anything, I'm doing this on a virtual machine since the computers around me are all Windows 7s.
Click to expand...
Click to collapse
all this works using windows 7

dustyjerran said:
all this works using windows 7
Click to expand...
Click to collapse
I did try this yesterday on Windows 7 but most guides I see do it on older versions. I will try again a little later. Thank you.

I tried it on Windows 7. Still the same error. Kindle is frozen and on Device Manager it says "This device cannot start. (Code 10)"

I ran into the exact problem yesterday. I thought I bricked my kindle. That was scary. Anyway, the problem is that you're stuck on fastboot, mode 4002 instead of a normal mode 4000.
Following rootzwiki.com/topic/12363-how-to-windows-install-twrp-20-on-your-kindle-fire/
You'll need to add a new vendor id (0x18d1). However, even with that the device still will not be recognized right away. Following another user's suggestion on that same thread, I let the battery drained out. Once that's done, reconnecting the Kindle will show up as simply "kindle" on the device manager instead of the normal "unrecognized device".
Then do the adb commands (even if it doesn't show any device attached)
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
Click to expand...
Click to collapse
Your device will reboot out of the stuck "kindle fire" logo screen. If your device goes dark after, it just means that the battery need to recharged first. Another scary moment for me. You can unplug and use the wall charger, much faster than charging by PC. After 5 - 10 minutes, you should get back to your normal screen. Then, just use the Kindle Utility to install TWRP.

You'll need to add a new vendor id (0x18d1).
Click to expand...
Click to collapse
I added this already
reconnecting the Kindle will show up as simply "kindle" on the device manager instead of the normal "unrecognized device".
Click to expand...
Click to collapse
Actually, the problem with mine is that it's detected. However, it shows up as Code:10, The device is unable to start.
Still, I'll try to drain it first, tinker with it next and see what happens. That or I'll wait for tomorrow and open the whole device already and see if I can OMAP it.

Mine also did show up as code 10, and sometimes code 43 ... I tried uninstalled the driver and reinstall it manually each time and eventually showed up as unrecognized ... so I tried the battery drain ... I even tried putting it in the freezer to quicken the drain but not sure if it actually help ..

I tried the battery draining. Nope, still didn't work
UPDATE: I take this back. After draining the battery, I would like to confirm that the issue has been fixed. Thank you, THANK YOU Everyone! )
I REALLY APPRECIATE THE EFFORT. HAPPY HOLIDAYS! )

A family member recently got a Kindle Fire, I tried to flash recovery but it got stuck in fastboot mode. Windows will recognize it as uknown device but Linux won't detect anything in fastboot or adb.
I will try battery drain out since kaswistry said it worked
If all else fails, I will try this.. http://forum.xda-developers.com/showthread.php?t=1405052
EDIT: nevermind lol, this worked.. http://forum.xda-developers.com/showpost.php?p=20619033&postcount=11 even though i tried it several times already..

I have the same problem too, the kindle fire stuck at the boot logo
kf utility show that when i try to restore or other option!
Changing bootmode doesent work at all
*imageshack/photo/my-images/10/60506677.png/[/url] (imageshack link)
KF utility status fastboot... offline
*imageshack/photo/my-images/834/kfustatus.png/
My computer have the right driver!
can anybody help me?
*sorry for my bad english*

Could it be that something destroyed my FireFireFire boot? My KF always gets stuck in fastboot when I try to flash ... obviously quite annoying.

u guys need to talk to vashypool in irc and he can fix it!! he fixed mine and mine was a complete brick

If it gets stuck in fastboot you need to run the command fastboot idme bootmode 4000 from the Android SDK.
Sent from my Kindle Fire using Tapatalk

In my case, i have tried to install the original 6.2 kindle firmware with TWRP. After that, the kindle staying stuck on the boot logo... This is me story... I think my kindle is stuck on fastboot! I tried to change bootmod with FK utility v.6
This is what kf utility gave me, when i try to reinstall twrp
imageshack.us/photo/my-images/10/60506677.png/
And this is the kf utility status
imageshack.us/photo/my-images/834/kfustatus.png/
Is anybody can say me, if my kindle is bricked for ever? Or have a solution
Happy holiday btw
#sorry for my poor english#

[SOLVED] Stuck at the KF logo

I seriously need some help. My normally fierce Google-fu has failed me. I have searched countless threads on here (and elsewhere) and tried just as many solutions, but I haven't had any luck. My Kindle Fire is stuck at the "Kindle Fire" boot logo. I was using the KF utility, and ADB status was online, everything looked good. I chose the option to root and install TWRP. However, it couldn't grab TWRP through my corporate firewall/proxy, so it skipped it, placed my KF in fastboot (I think), rebooted, now I'm bricked.
Depending on which PC I use, and in what order it's plugged in, I get different results in the Device Manager (both Windows 7):
Home PC -
Hardware Ids = USB\UNKNOWN
Yes, I've tried loading drivers six ways from Sunday, and none worked.
Absolutely no solution involving ADB in any way will work until I can at least get Windows to recognize it correctly and load the proper drivers.
Work PC -
If I have the KF turned on when I plug it into my PC, I get the same result as on my home PC (though I don't think I tried plugging it in on my home PC while my KF was powered off).
If I have it turned off when I plug it in, my PC sees it as an "Android ADB Interface", with the correct hardware ids.
Even when it sees my KF correctly in Device Manager, I still can't get ADB to communicate with it.
I've tried FireKit on my Ubunutu 12.04 laptop, but it never sees my device, and gets stuck at the <waiting for device> message. I've tried countless driver iterations and many utilities, and none seem able to communicate with it while it's stuck at the logo.
Any help would be immeasurably appreciated!!
[UPDATE]
While my device was detected correctly in Device Manager (but still not able to communicate via ADB), I reloaded the drivers using the KF Utility. It is still detected as "Android ADB Interface" but with an error in Device Manager. The error is "This device cannot start. (Code10)". I uninstalled it, including drivers, and let Windows autodetect. It was identified as "kindle", so I ran the same driver package and it still sees it as "Android ADB Interface", but still with the error.
[UPDATE 2] - Steps I took to (finally) get mine working
Note: If your device is recognized in Device Manager as something *other* than "Unknown Device* (such as "kindle" or "Android ADB Interface"), skip to step 3.
1. Turn off the device.
2. Plug the device into USB to your computer. This should turn the device on.
3. Delete the ".android" folder from your Windows profile. This is very important. If you just uninstall the device and driver, Windows will still use this to reinstall the device. You want to start as fresh as possible to eliminate complications from previous attempts.
4. Uninstall it from Device Manager. Make certain to check the box to uninstall the driver as well.
5. Start a new scan for hardware changes in the Device Manager.
6. As mine was stuck in fastboot mode, it recognized the device as "kindle" (lower-case "k")
7. Run the "install_driver.bat" from the Kindle Fire Utility.
8. After driver install, run the Kindle Fire Utility.
9. ADB status will say "offline", that's fine.
10. Choose option 1 to go into the Bootmode Menu.
11. Choose option 1 to boot into Normal Mode.
12. It will be stuck at <waiting for device>.
13. Turn off the device, keeping it plugged into the PC. *very important* This step was one among others that made THE difference for me.
14. Turn on the device. *Hopefully*, you should immediately see the utility spit out some text and your device should reboot.
15. Boots up!! (well, mine did, and I had almost give up hope were it not for my pride and stubbornness).

Read this...
http://forum.xda-developers.com/showthread.php?t=1552547
with emphasis on device drivers.
"Android ADB Device" typically means the device is in fastboot mode and you cannot use adb while in fastboot mode.... you must use fastboot.
With your KF off and disconnected from your work computer, run this command...
Code:
fastboot -i 0x1949 getvar product
and then connect it to the computer. The KF will turn on automatically. The computer will say "<waiting for device>" for a bit, but if the command works, it will eventually return "product: kindle" as output. If that works, you can actually flash TWRP from there, but if you are anxious for it to do something again...
Code:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
should get it booting normally again. If it doesn't, look at the link I gave you and focus on getting your drivers fixed. You won't be able to execute any commands (fastboot or adb) through Windows if the device drivers don't work. You might want to go back to Firekit if drivers remain problematic for you.
Everything you need to know to fix your KF is in that link at the beginning of my post, including the commands you need to run. At the bottom of post #3 is also another link to a how-to root/install ROMs page.

IT LIVES!!! While I was still getting the error code 10, I launched the KF utility one more time. ADB status was still offline. I went into the menu to modify boot mode, told it to boot in normal mode and it was stuck <waiting for device>. On a whim, I left it there and cycled power on my KF. It found the device, finished, rebooted, and it's good!!! The Device Manager is happy now too!!
The behavior was so odd between my work and home PC. I was seriously scared when it gave a bad device ids on my home PC. I think it was more a combination of several different things that helped, and I'll update my main post with all that I did to get it back (that I can remember). Hopefully it will help someone else.
This is an *amazing* community, and I can't thank everyone enough for the incredible work you all do and the true sense of selflessness exhibited here on the forums!
btw, How do I edit the subject to indicate it's solved?

^_^
OH ,MY GOSH I DO NOT NO HOW MUCH TO THANK U THNX FOR THE POST

jaetrix said:
OH ,MY GOSH I DO NOT NO HOW MUCH TO THANK U THNX FOR THE POST
Click to expand...
Click to collapse
Glad it could help someone! I was frustrated enough about it and couldn't find a single solution that fit my issue. I just had to combine some to get it to work for me.

Bump

Yes this saved two bricked kindles. Trial and error is sometimes the best means to solving a problem.
Sent from my GT-I900 using xda premium

This is happening alot here of recent thats why I bumped it to the top of the list

Thank you for this. Maybe a moderator will be kind enough to sticky this.
Sent from my Galaxy Nexus using Tapatalk 2

pugsley42 said:
I seriously need some help. My normally fierce Google-fu has failed me. I have searched countless threads on here (and elsewhere) and tried just as many solutions, but I haven't had any luck. My Kindle Fire is stuck at the "Kindle Fire" boot logo. I was using the KF utility, and ADB status was online, everything looked good. I chose the option to root and install TWRP. However, it couldn't grab TWRP through my corporate firewall/proxy, so it skipped it, placed my KF in fastboot (I think), rebooted, now I'm bricked.
[...]
15. Boots up!! (well, mine did, and I had almost give up hope were it not for my pride and stubbornness).
Click to expand...
Click to collapse
Pugsley42...you 'da man! I had the same story as you told above, including searching and following countless threads of instructions. Nothing worked until I found your instructions! Thank you, thank you, thank you!

Stuck at the KF logo
These steps still didn't work for me :-/ I'm still stuck with the KF logo and a "Waiting for device" prompt. I've read through these forums starting with the "KKFB" to this one and still haven't had any luck yet. It may be time to give up on her. I think I have royally messed her up.
If anyone else has any other suggestions I'm open i've tried everything else on here I can find.
Thanks
Neely

Neely said:
These steps still didn't work for me :-/ I'm still stuck with the KF logo and a "Waiting for device" prompt. I've read through these forums starting with the "KKFB" to this one and still haven't had any luck yet. It may be time to give up on her. I think I have royally messed her up.
If anyone else has any other suggestions I'm open i've tried everything else on here I can find.
Thanks
Neely
Click to expand...
Click to collapse
My first suggestion would be to read this:
http://forum.xda-developers.com/showpost.php?p=25884555

Neely said:
These steps still didn't work for me :-/ I'm still stuck with the KF logo and a "Waiting for device" prompt. I've read through these forums starting with the "KKFB" to this one and still haven't had any luck yet. It may be time to give up on her. I think I have royally messed her up.
If anyone else has any other suggestions I'm open i've tried everything else on here I can find.
Thanks
Neely
Click to expand...
Click to collapse
Agreed, you really need to be more specific. "Waiting for device" .... which part of the KF utility?. What *exactly* are you seeing, where? What does Device Manager show your KF identified as (keep in mind, there is a big difference between seeing it as "Kindle" and "kindle"). What *exactly* did you do that brought you to this point?
Symptoms. Symptoms. Symptoms. The more detail you provide, the more likelihood we can help.
Take heart. If there's anything I learned in my stubborn refusal to admit my KF was fully bricked, is that it can be brought back from a lot worse than we give it credit for. I also learned quite a bit that I never would have if I never failed. That's what I love about breaking things!

pugsley42 said:
Agreed, you really need to be more specific. "Waiting for device" .... which part of the KF utility?. What *exactly* are you seeing, where? What does Device Manager show your KF identified as (keep in mind, there is a big difference between seeing it as "Kindle" and "kindle"). What *exactly* did you do that brought you to this point?
Symptoms. Symptoms. Symptoms. The more detail you provide, the more likelihood we can help.
Take heart. If there's anything I learned in my stubborn refusal to admit my KF was fully bricked, is that it can be brought back from a lot worse than we give it credit for. I also learned quite a bit that I never would have if I never failed. That's what I love about breaking things!
Click to expand...
Click to collapse
Okay, I was attempting to load a ROM on it. It had been rooted already with no issues and then something happened during the installation of TWRP and spit out an error message of unable to load and then rebooted. That's where I am with the kindle fire boot screen.
As for the "Device Manager" It shows up as "Android Composite ADB Device" and with KFU it shows the following status:
ADB Status: Online
Boot Status: Unknown
At this point is when if I try to run Install Latest TWRP Recovery or FFFF or anything it just sits there and says "Waiting For Device"...
I've read though most of these posts and have tried several different suggestions with no luck so far. So I have actually read through here. :-/
Hope this helps at all.

I would try by trying to change the bootmode using the KF utility. If you're stuck at the KF logo on boot, then the other functions of the utility won't do anything. Your KF needs to be in a "usable" state before that can happen. Have you tried changing it to "Fastboot" or "Normal"?

Stuck at the KF logo
pugsley42 said:
I would try by trying to change the bootmode using the KF utility. If you're stuck at the KF logo on boot, then the other functions of the utility won't do anything. Your KF needs to be in a "usable" state before that can happen. Have you tried changing it to "Fastboot" or "Normal"?
Click to expand...
Click to collapse
Yeah, I've tried it using the KF Utility as well as using fastboot at the command line :-/

kinfauns said:
Read this...
http://forum.xda-developers.com/showthread.php?t=1552547
with emphasis on device drivers.
"Android ADB Device" typically means the device is in fastboot mode and you cannot use adb while in fastboot mode.... you must use fastboot.
With your KF off and disconnected from your work computer, run this command...
Code:
fastboot -i 0x1949 getvar product
and then connect it to the computer. The KF will turn on automatically. The computer will say "<waiting for device>" for a bit, but if the command works, it will eventually return "product: kindle" as output. If that works, you can actually flash TWRP from there, but if you are anxious for it to do something again...
Code:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
should get it booting normally again. If it doesn't, look at the link I gave you and focus on getting your drivers fixed. You won't be able to execute any commands (fastboot or adb) through Windows if the device drivers don't work. You might want to go back to Firekit if drivers remain problematic for you.
Everything you need to know to fix your KF is in that link at the beginning of my post, including the commands you need to run. At the bottom of post #3 is also another link to a how-to root/install ROMs page.
Click to expand...
Click to collapse
Your explanation and guidance cut right to the solution for me. Thank you so much!

Thank you!!
I've been searching forever for this same issue. This has not fixed it completely but has helped me! Thank you for taking the time to post this!!

cmgroden said:
I've been searching forever for this same issue. This has not fixed it completely but has helped me! Thank you for taking the time to post this!!
Click to expand...
Click to collapse
I presume if any of this helped, you were able to get further than you have been. What state is it in now? What error(s) if any?

I seem to be having this same issue but I cannot get my pc to recoginze the kindle fire as anything. perhaps i did something wrong but i was following a video on youtube and though i was doing it exactly as it showed. First thing i did after I finally got the drivers loaded was start KFU and then chose to load TWRP. It started the process but when it hit the part about rebooting my device that's where it stopped. Since then i've been stuck at the white and yellow kindle fire logo. No matter what i do to try to reinstall the ADB drivers I cannot get my computer (win xp) to recognize the kindle. It shows as "unknown device" in device manager and when it's plugged in the little pop up says that the usb device has malfunctioned and windows doesn't recognize it. So am I totally dead? I'm assuming before i can do anything to recover it I need to get windows to recognize it with the ADB drivers.

[SOLVED!] Kindle Fire Bricked on Logo Startup - KFU v0.9.9

I am total noob. Just want to make that clear from the get go.
I hesitate to start a new thread, but I have been working on this forever, and have not made any progress.
I have a Kindle Fire that I would like to run android on - I started the process with the Kindle Fire Utility v 0.9.9. Something went wrong, and it is now stuck on the Kindle Fire start up logo. I also can no longer see it in the device manager, nor is it responsive to anything in the Utility. (ADB status: Offline Boot Status: Unknown). I am at a loss, does anyone have any ideas? Your help is appreciated!
.................FIGURED IT OUT!..............................
Much thanks to the pooch who spent hours helping me troubleshoot.
What we (he) did, as far as I remember, hopefully this can be of some service to someone else out there.
1) Figured out that trying all of this on a Virtual Machine is not a good idea!
2) I somehow broke the bootloader in my first attempt, so none of my computers were recognizing the KF.
3) Created a Pendrive to run Linux (ubuntu). Here Requires a USB drive formatted Fat16/Fat32/NTFS, minimum of 2 gb.
4) Once I got Linux running, installed SoupKit.
5) Went through a few tries of booting, rebooting, into recovery mode until the Kindle flickered back to life!
6) Followed prompts on SoupKit to install TWRP, updated TWRP, install FireFireFire, install Android 4.2.
Good luck, I am happy to answer any questions - though I am no means an expert now.

What I have tried...more info
More Information:
I am running Windows7 in a VirtualBox on an iMac.
I bricked the Kindle a few weeks ago, after messing with it then, I bought a factory fastboot cable. Still no dice.
I have tried all turning on and off computer, on and off Kindle with it disconnected, connected, going through the KFU 4 seconds after starting the Kindle. Letting the Kindle's battery die, recharging.
I have deleted .android folder, reinstalled drivers, re-downloaded KFU.
I have tried on a different computer (Windows XP) The Kindle is also not recognized there.
I have tried booting into Ubuntu (however in the directions there, it said the FireKit is for more "serious" issues than my soft brick.
I am sure there is some small detail I am missing, but I have not been able to find it - and I am not knowledgeable enough to properly diagnose the problem. Again thanks for any help.

kyleboyd said:
I am total noob. Just want to make that clear from the get go.
I hesitate to start a new thread, but I have been working on this forever, and have not made any progress.
I have a Kindle Fire that I would like to run android on - I started the process with the Kindle Fire Utility v 0.9.9. Something went wrong, and it is now stuck on the Kindle Fire start up logo. I also can no longer see it in the device manager, nor is it responsive to anything in the Utility. (ADB status: Offline Boot Status: Unknown). I am at a loss, does anyone have any ideas? Your help is appreciated!
Click to expand...
Click to collapse
Sometimes KFU will show as Unknown even though it's really fine. I had the same issue as you. Try switching boot mode to Normal and see if that fixes it, it worked for me.

Read this (everything),especially third post.
http://forum.xda-developers.com/showthread.php?t=1552547

hemmulde 1st
zastava750 said:
Read this (everything),especially third post.
http://forum.xda-developers.com/showthread.php?t=1552547
Click to expand...
Click to collapse
Thanks for the reply!
I tried that. When I type "fastboot getvar product" it says waiting for device or something similiar.
The advice applying to Device Manager don't get me anywhere, because my Kindle doesn't show up.
Any other ideas?

kyleboyd said:
Thanks for the reply!
I tried that. When I type "fastboot getvar product" it says waiting for device or something similiar.
The advice applying to Device Manager don't get me anywhere, because my Kindle doesn't show up.
Any other ideas?
Click to expand...
Click to collapse
When using the stock bootloader (plain "kindle fire" boot logo), the fastboot command must always specify the custom vendor ID used by the Kindle Fire. For example, the commands above must be slightly altered to...
Code:
fastboot -i 0x1949 getvar product
fastboot -i 0x1949 devices
and likewise, all of the following commands will need the "-i 0x1949" switch when using the stock bootloader. The FFF bootloader's vendor ID has been changed to one that is normally recognized by fastboot, so the "-i 0x1949" switch can be omitted.
Now onto some more useful fastboot commands...
Code:
fastboot oem idme bootmode 4000
fastboot oem idme bootmode 4002
fastboot oem idme bootmode 5001
Using one of these commands will change the bootmode to normal (4000), fastboot (4002) or recovery (5001). Then issuing...
Code:
fastboot reboot
will reboot the device into the respective bootmode.

I've tried that as well...
Just so I am totally clear, this is what I did in relation to those instructions:
Opened Command Prompt - set the directory to C:/kfu/tools
Typed "fastboot -i 0x1949 getvar product" (with out the quotations, obviously)
<waiting for devices>
I plugged Kindle in, it powers on and the frozen logo pops up.
I also tried "fastboot -i 0x1949 oem idme bootmode 4000" and "fastboot -i 0x1949 oem idme bootmode 4002"
According to the guide it often takes multiple tries, I have done it over and over again.
I have also tried different orders of code, plugging in Kindle, and powering on and off.
Am I doing something wrong? Is there a specific code for my Kindle? (Not -i 0x1949)
Thanks!

Have you tried this?
http://forum.xda-developers.com/showthread.php?t=1660636

Reinstall the driver then use kfu to reset the boot mode to normal.

Drivers?
I did try this: http://forum.xda-developers.com/show....php?t=1660636
When I get to the part about the Device Manager, I am stuck, as nothing shows up (I suspect something do with drivers)
Thepooch said:
Reinstall the driver then use kfu to reset the boot mode to normal.
Click to expand...
Click to collapse
By reinstall drivers do you mean clicking on "install_drivers" in the KFU folder? I have tried that.
Is there another method of uninstalling and installing drivers? Sorry if that is a dumb question!

If the devices is in fastboot which I believe it is it would show up as android adb interface, if it was attempting to boot to the system it would show up as android composite adb interface. If you are on xp or windows 8 this can be a bit of a tricky task. Android adb interface and android composite interface are two facets of the same driver. So yes I suggest rerunning the driver installation bat that is packaged with KFU. If perhaps you are on windows 8 you must disable driver signature verification and reinstall the driver. 3.0 usb ports have an issue with fastboot and can leave the device undetected.

Still not working
Thepooch said:
If the devices is in fastboot which I believe it is it would show up as android adb interface, if it was attempting to boot to the system it would show up as android composite adb interface. If you are on xp or windows 8 this can be a bit of a tricky task. Android adb interface and android composite interface are two facets of the same driver. So yes I suggest rerunning the driver installation bat that is packaged with KFU. If perhaps you are on windows 8 you must disable driver signature verification and reinstall the driver. 3.0 usb ports have an issue with fastboot and can leave the device undetected.
Click to expand...
Click to collapse
Thanks for the quick reply.
So I am on a Win7 and/or a Windows XP. Currently on both systems, when I plug it into the computer, with the Device Manager open, nothing happens other than the Kindle turning itself on.
Before it froze up, I saw it in device manager as Android ADB interface, and before doing anything at all, saw it as the default Kindle Fire.
On the Win7 system, I have rerun the driver installation bat over and over and over again, with absolutely no results.
On the WinXP, I have tried it, and for the life of me can't get it to install (it says install failed (Unsigned)). I never connected the Kindle up to this computer before it froze up, so I wonder if that is somehow causing the problem (it is trying to update drivers that don't exist?)
Am I doing something wrong with this? Can I uninstall or delete drivers, and totally start over?

If you are using a WinXP you must install driver manually.

Drivers?
zastava750 said:
If you are using a WinXP you must install driver manually.
Click to expand...
Click to collapse
How do I do that, when the Kindle does not show up as being connected? All the guides I have found start off with accessing from the Device Manager. My Kindle does not show up in the Device Manager...

okay well then you`re running xp use another computer getting the driver installed is hard even for the very skilled particularlly when the device is stuck in fastboot. Friend or relatives computer running windows 7 would be perfect. Otherwise it`s linux on a live usb booted on your xp machine.

Windows 7 - No Dice
Thepooch said:
okay well then you`re running xp use another computer getting the driver installed is hard even for the very skilled particularlly when the device is stuck in fastboot. Friend or relatives computer running windows 7 would be perfect. Otherwise it`s linux on a live usb booted on your xp machine.
Click to expand...
Click to collapse
Yeah so I have a Windows7. I have reinstalled the drivers (by clicking on the install_drivers.bat file in the KFU) over and over again, and I still do not get any recognition on the computer, or in the Device Manager when I plug in the Kindle.

Try different usb port, make sure they are usb 2.0. Is the logo static or animated? It possible that you broke the bootloader. At some point I would be willing to look at some things for you via teamviewer. If it is not driver related I fear your next move is here http://forum.xda-developers.com/showthread.php?t=1430038. Keep it on charger or off till it can be dealt with.

Thepooch said:
Try different usb port, make sure they are usb 2.0. Is the logo static or animated? It possible that you broke the bootloader. At some point I would be willing to look at some things for you via teamviewer. If it is not driver related I fear your next move is here http://forum.xda-developers.com/showthread.php?t=1430038. Keep it on charger or off till it can be dealt with.
Click to expand...
Click to collapse
Thanks! I would be willing to give it a shot (teamview I mean) if you are willing.
I tried the Firekit before I began this thread, but I kept getting stuck trying to run the tool after booting into ubuntu. Perhaps that is a different thread topic, but I am more than willing to put more work into figuring that out, if it could be the key to unlocking this stupid thing.

I am having this exact same problem. Using Win XP i was able to get the ADB drivers loaded initially and used KFU to try to install TWRP. When it rebooted during that process it got stuck at the Kindle Fire logo. Since then I cannot get my computer to recognize the kindle. Like you, I feel like i've tried everything.

Nixnaegie said:
I am having this exact same problem. Using Win XP i was able to get the ADB drivers loaded initially and used KFU to try to install TWRP. When it rebooted during that process it got stuck at the Kindle Fire logo. Since then I cannot get my computer to recognize the kindle. Like you, I feel like i've tried everything.
Click to expand...
Click to collapse
Glad to know I'm not alone - misery loves company! Solidarity my friend.
I wish I could tell you I'd solved it, but alas, I have not. I'm still working on it, I'll keep you updated if I have any breakthroughs!

Red Screen + no fastboot

Hello all
I realize the one post below me is almost the exact same problem, but I am stuck. I just got my kindle hd 89 and I already have a red screen. Every option I try to use to get fastboot does not work, whether I'm using cmd and typing in the command, using KFFA, or KFHD 2.1. I think I ended up with a red screen by using FireFlash but without checking the right options. If it matters, I started with 8.4.6. I really want to unred-screen this, so any help would be appreciated! Thanks.

hi beatmastermcfly,
I guess this will be a driver problem, for me win 7 64bit it works perfectly.
Have you ever tried KFHD_SRTv1.3-8.1.2 to start on another PC? Did you run it as an Admin?
You get a red screen when you try to SRT to enter fastboot?
mfg
JPL

GermanJPL said:
hi beatmastermcfly,
I guess this will be a driver problem, for me win 7 64bit it works perfectly.
Have you ever tried KFHD_SRTv1.3-8.1.2 to start on another PC? Did you run it as an Admin?
You get a red screen when you try to SRT to enter fastboot?
mfg
JPL
Click to expand...
Click to collapse
I used KFHD_SRTv2.1- 8.1.4 and I am going to try KFHD_SRTv2.0- 8.1.3 , but the link to KFHD_SRTv1.3-8.1.2 in this thread appears to be dead. Anyone have a mirror?
And yes, the issue I'm having with KFFA, the SRT, and even when I am just trying to boot into fastboot via cmd, is that it says "waiting for device" and then when I plug it in it says "KindleFire" (in orange) for a second or two before switching over to the red screen.
I was able to do fastboot before the red screen showed up, so I doubt it has anything to do with drivers.

hi beatmastermcfly,
I asked because I recently in a German Help - Forum have 3 different PC's tried it with a user (always bare OS with identical increments). Only after 1 week it has then eventually folded.
the Pc's have not accepted the Fastboot.exe for any reason.
mfg
GermanJPL

GermanJPL said:
hi beatmastermcfly,
I asked because I recently in a German Help - Forum have 3 different PC's tried it with a user (always bare OS with identical increments). Only after 1 week it has then eventually folded.
the Pc's have not accepted the Fastboot.exe for any reason.
mfg
GermanJPL
Click to expand...
Click to collapse
I do not understand what you are saying.

I will say that when I plug the Kindle in, my laptop makes the "device connected" noise followed quickly by the "device disconnected" noise and it even shows up in the device manager for the split second before it turns red.

What exactly is the device that shows up in the device manager call itself before it disappears? And does it have a yellow triangle on it?
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app

stunts513 said:
What exactly is the device that shows up in the device manager call itself before it disappears? And does it have a yellow triangle on it?
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
At first it showed up under "portable devices" as an "unknown device" and I managed to uninstall the drivers in the hopes of re-installing them, and then the next time it showed up under "portable devices" as "jem-004..." etc. or whatever the code name for this type of kindle is. I think it just shows up as the category "other devices" now, but I do not have the kindle handy.

Depending on if it manages to stay connected long enough you might be able to install the drivers in my SIG, but I think windows cancels the driver install if it disconnects in mid install. If that's the case and running "fastboot -i 0x1949 getvar product" and then plugging the kindle in doesn't go into fastboot you may need to boot a ubuntu live CD and do this from a terminal since the drivers work differently on Linux, they load up immediately without you having g to install anything.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app

stunts513 said:
Depending on if it manages to stay connected long enough you might be able to install the drivers in my SIG, but I think windows cancels the driver install if it disconnects in mid install. If that's the case and running "fastboot -i 0x1949 getvar product" and then plugging the kindle in doesn't go into fastboot you may need to boot a ubuntu live CD and do this from a terminal since the drivers work differently on Linux, they load up immediately without you having g to install anything.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
Your drivers just saved my life dude. Thank you so much. Gotta figure out the next step now.

stunts513 said:
Depending on if it manages to stay connected long enough you might be able to install the drivers in my SIG, but I think windows cancels the driver install if it disconnects in mid install. If that's the case and running "fastboot -i 0x1949 getvar product" and then plugging the kindle in doesn't go into fastboot you may need to boot a ubuntu live CD and do this from a terminal since the drivers work differently on Linux, they load up immediately without you having g to install anything.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
oh but seriously dude running CM10.1 now and could not be happier thank you so much.

Your solution to fastboot and redscreen issue
Hey beatmastermcfly,
I'm having the same issue you had with the red screen and fastboot not working.
Are you able to walk me through the solution you had with the the drivers that were recommended?
Did you end up using Ubuntu, or did you figure out how to do it in windows 7?
cheers

Hello I am very sorry to ask for help, I have this same problem and can help stunts513 beatmastermcfly, my kindle has a red screen and make everything after root, and the worst part is that my laptop recognizes it as unknown device which driver you downloaded work for you
:crying:

Dead Kindle Fire HD 8.9
Okay, due to my own errors while using fastboot on my KF, it no longer does *anything* when I try to turn it on. I can't reenter fastboot, since ADB no longer recognizes the device (which of course, it can't, since the device doesn't start). I mean, it does *nothing* (although the hardware is in great shape).
Am I, as I suspect, just dead in the water here? I have the recovery files, but without ADB or fastboot, I no longer have a way to load them.
Should I just start using the KF as a doorstop now? Or is there some obscure solution to this mess?
rogerlig

Someone correct me but figuring concludes that the red screen is because amazon blocks tablet when it comes to a stolen board or losses , my I get a tablet I did not say much , so that the repaired but through the serial number of a personal contact amazon and they said it was lost and I imagine blocked the operating system so I could not use the tablet

Please Help!
Meeperman said:
Hey beatmastermcfly,
I'm having the same issue you had with the red screen and fastboot not working.
Are you able to walk me through the solution you had with the the drivers that were recommended?
Did you end up using Ubuntu, or did you figure out how to do it in windows 7?
cheers
Click to expand...
Click to collapse
Did you ever find a solution? Thanks!

On a win7 x64 box you need adb (there is a quick version) installed. The kfhd drivers. USC disabled. AND MOST IMPORTANTLY YOU MUST RUN ADB FROM A COMMAND PROMPT ORIGINATED FROM THE ADB FOLDER. (shift+right click and select "run command prompt from here)

Did you ever get your kfhd 8.9" to work. Everything youve said so far is the exact replica of my kindle. I know its like 7 years later but this is still a problem for people

Juhpan said:
Did you ever get your kfhd 8.9" to work. Everything youve said so far is the exact replica of my kindle. I know its like 7 years later but this is still a problem for people
Click to expand...
Click to collapse
this is a COPY/PASTE of my own post. the files i specify are the exact names, just search this section of X-DA for them. SEE BELOW.
i had the same problem with the "red screen of death" as well. i found that if i installed the "Minimal ADB and Fastboot" and / OR (i did the minimal first.... ) KFHD_SRTv1.3.5 and RUN THE APP FIRST, then when it says "waiting for device" you then plug in the ALREADY OFF tablet it then WORKS!! says "fastboot mode" on the tablet. and it is listed in device manager also.
i got BOTH apps here at this board in this section.
WARNING: i run windows XP with all updates as of 10-31-2017 (pm me for info, 2 lines of text!! ) . NEWER windows versions have "permission issues". fixes are posted in multiple topics here in the Amazon 7" Kindle Fire HD, 8.9" Kindle Fire HD, Kindle Fire 2 section. READ THEM!!

Kindle Fire HD 8.9 red triange after root.

Please help me!
I rooted my girlfriend's Kindle a few days ago in order to install the Google Play store. Managed that just fine and installed a few apps. I then decided it would be a good idea to change the launcher and get shot of the carousel. I tried the next Launcher 3D and followed an online guide to install it. On rebooting the Kindle I got a constant pop up advising Next Launcher 3D had stopped working. It popped up continually every 1/2 second or so and I couldn't get rid of it,
Again I had a look online and found a guide to removing it using command prompt script via ADB. I went through the instructions correctly but it kept telling me the app didn't exist. Using the dir command showed the app though. Confused I tried again a couple of times. I then got a pop up on the device telling me another app.....something relating to Swype had stopped working. The Kindle rebooted itself and presented a screen with a red triangle and 'Kindle Fire System Recovery' giving me the options to either reboot or reset to factory defaults. I tried both of these options (perhaps foolishly) and had no success.
I was given some further advice from a very helpful poster on here to get KFFAide v100 and enter some fastboot commands. On entering the command 'fastboot -i 0x1949 getvar product', the script shows 'waiting for device'. Powering on the device at that point does nothing more than booting to the same screen with the red triangle. Windows does not acknowledge that the device is connected at all.
It would seem I was hasty in rooting the device. Having rooted several other Android devices I was clearly overconfident in my ability and now find myself at a loss. Is there any way at all for me to recover the device at this point? Or should I now file this under 'very expensive experience and education'?

Its completely fixable, you just need to install the fastboot driver, if u open the device manager and plug the kindle in when its off, it should briefly show up as a jem device, while it shows up as that tell it to update the drivers and use the ones in my signature and it should install. It might give you problems installing though if it disconnects before the driver can finish installing. Once the driver is installed then power it off and unplug it and run the previous command and then plug it in. Now it should go into fastboot. If you can't get the driver to install, u should try using an Ubuntu live CD, since it doesn't use drivers in the same way windows does, it loads up the driver automatically so you wouldn't have this problem. Once this is in fastboot just reflash the system partition, if u hadn't factory reset it, it would still have all the data and apps, but as is its going to be "fresh out of the box".
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app

stunts513 said:
Its completely fixable, you just need to install the fastboot driver, if u open the device manager and plug the kindle in when its off, it should briefly show up as a jem device, while it shows up as that tell it to update the drivers and use the ones in my signature and it should install. It might give you problems installing though if it disconnects before the driver can finish installing. Once the driver is installed then power it off and unplug it and run the previous command and then plug it in. Now it should go into fastboot. If you can't get the driver to install, u should try using an Ubuntu live CD, since it doesn't use drivers in the same way windows does, it loads up the driver automatically so you wouldn't have this problem. Once this is in fastboot just reflash the system partition, if u hadn't factory reset it, it would still have all the data and apps, but as is its going to be "fresh out of the box".
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
Hi Stunts513. Thank you for your reply. Have tried what you said above and Windows (8) just doesn't detect that the device has been connected. No pop up from system tray, nothing in file explorer and nothing, not even for a second in device manager.
Am at a loss for the moment. Will have to get hold of an Ubuntu CD and try that way. Am just praying it detects the Kindle. Didn't on my girlfriends laptop nor my PC so am mildly panicked just now.

OK, so I went through Linux Mint and installed the SoupKit and tried it that way. Same result. The device just isn't detected at all. Really starting to fear the worst here. The fact it's still powering on should give me some faith but i've tried all I can think of and everything advised and cannot proceed past this point.
Does anyone have any last gasp possibilities for me? Borderline desperate here now.... will try anything at this point.

In linux did you run "fastboot -i 0x1949 getvar product" with the kindle unplugged, and then after the command says waiting for device, plug the kindle in? Because on Linux, unless you know where to look its not going to really notify you that its plugged in. It probably will in the kernel logs in the f1 virtual terminal. If you can't get the device to respond to that command, hit Ctrl+alt +F1, and plug the kindle in with it off, and see if you notice anything in that terminal about jem, otter, or Tate coming up at the bottom of the terminal.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app

stunts513 said:
In linux did you run "fastboot -i 0x1949 getvar product" with the kindle unplugged, and then after the command says waiting for device, plug the kindle in? Because on Linux, unless you know where to look its not going to really notify you that its plugged in. It probably will in the kernel logs in the f1 virtual terminal. If you can't get the device to respond to that command, hit Ctrl+alt +F1, and plug the kindle in with it off, and see if you notice anything in that terminal about jem, otter, or Tate coming up at the bottom of the terminal.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
Did exactly that. Brought up the virtual terminal. Nothing.
Have tried everything now I think. Used different PCs. Different cables. Different OS. Tried bypassing getvar and just trying a manual command "fastboot -i 0x1949 flash recovery recovery.img". Nothing is getting any response from this device other than booting to the recovery screen.
Suspect I may be out of luck.

Are you absolutely positive this was an 8.9” model and not a 7” model, because the method to get it into fastboot without a fastboot cable doesn't always work with 7” models if I remember right, so if its a 7” model you just would need a fastboot cable to get it into fastboot mode, but on the 8.9” models we don't use fastboot cables, hence the command.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app

stunts513 said:
Are you absolutely positive this was an 8.9” model and not a 7” model, because the method to get it into fastboot without a fastboot cable doesn't always work with 7” models if I remember right, so if its a 7” model you just would need a fastboot cable to get it into fastboot mode, but on the 8.9” models we don't use fastboot cables, hence the command.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
Yeah it is most definitely an 8.9 model. Am not sure what I have done to it but it is not being detected by any OS whatsoever. Have bitten the bullet and bought the Mrs a replacement. Expensive error on my part.

Out of curiosity, was it still under warranty?(not counting the fact you technically voided it) Also what are you going to do with the old one? I can think of a person that needs one to try to make a hard brick fix for the kfhd models, he has a working unhardbricking method right now, but it still is in a complicated soft brick state, anyways he's making these pcb's that attach to the kindles motherboard to directly access the emmc to flash it from Linux. Long story short he has made on for kf2, but doesn't own a 7" or 8.9" model, and if he can get his hands on one it could potentially profit the community greatly.
But yea if it was still under warranty you could probably get a new one for free, I only mention what I did above to either hard bricks or people getting new ones, I don't typically just ask people to do this. Would be kinda rude if I did...
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app

stunts513 said:
Out of curiosity, was it still under warranty?(not counting the fact you technically voided it) Also what are you going to do with the old one? I can think of a person that needs one to try to make a hard brick fix for the kfhd models, he has a working unhardbricking method right now, but it still is in a complicated soft brick state, anyways he's making these pcb's that attach to the kindles motherboard to directly access the emmc to flash it from Linux. Long story short he has made on for kf2, but doesn't own a 7" or 8.9" model, and if he can get his hands on one it could potentially profit the community greatly.
But yea if it was still under warranty you could probably get a new one for free, I only mention what I did above to either hard bricks or people getting new ones, I don't typically just ask people to do this. Would be kinda rude if I did...
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
Many apologies for the delay. i managed to get the Kindle up and running following your advice coupled with that on another thread. Although it wouldn't detect in either Windows 8 or Ubuntu, it did so on Windows XP. Don't imagine you can begin to explain that one any better than I can as it's entirely illogical......but there you go. From there it detected as a JEM device and I was able to run KFFA and do a complete restore.
I now have it the way I intended to have it in the first place. Changing the launcher was fruitless as I couldn't get the wallpaper fix to work but am fine with that. had a look at customising the icons on the carousel but boy does that look like more trouble than it's worth!! Lol.
I wont pretend I was going to send my Kindle off to you guys. In truth I would have sold it to recoup some of my losses and raise funds towards the replacement. I will however be making a donation to the team very shortly as a token of my appreciation.
Thank you very much for all your help. it is greatly appreciated.