Hello Everyone,
I will try to provide as much details as I can from what I remember.
Basically, I tried to ROOT my device and install TWRP. However, I messed it up the first time. I tinkered with it for hours but it still couldn't work until finally, after hard resetting for the unlimited time, it booted up.
The problem though, is that it wasn't rooted and TWRP wasn't installed when it came up so I tried it again. Second try, second time it was messed up. Annoyingly, I don't know what I did earlier to make it work. The second instance it happened is just like the first.
Just to be clear, this isn't the boot screen where the kindle fire logo is animated (has reflections). In my case, its the logo as is, stuck on the screen just like that. Tried hard resetting, doesn't work.
What do I know?
1) From my earlier experience, it has lesser to do with the system (PC, Mac) and drivers since I managed to get it boot up again without being connected the first time
2) If I do connect it to the PC, it says Cannot Start Device/Unable to Start Device. Code:10. That's it. Even if I reboot the device, its still the same.
3) If you connect it to the Mac, it is detected in system preferences. Problem though is that I tried using adb and just like its windows counterpart, there are no devices detected.
THOUHGTS:
1) I know I just have to get it to be recognized and I can change the bootmode. Something's telling me that its a boot mode problem only. In my earlier V3X phone, I used to TP (testpoint) if anyone's familiar with that, or shortcircuit the board to get it out of the 'loop'. Do we have that with the kindle fire?
2) What operating system would it be easiest to get the device detected. I'm hoping that if there's lesser complications with the device being detected by the computer, be it mac, linux or windows, I can change the bootmode. my technical instinct tells me it has something to do with boot mode.
What have I done already?
1. Let me see, I believe I tried hard resetting it for ALOT of times already
2. Reinstalled drivers on PC. Used both Android and Kindle Fire Utility drivers. Even checked the /android folder
3. I'm using a Nokia Micro-USB cable. I'm not sure if that has any impact on the device or its effectiveness but I will try to pick-up another cable today and post later.
I would really appreciate if anyone can help. It sucks that I tried this just after unboxing the unit. I haven't even tried doing anything on it yet.
If you can help, ANY help would be appreciated.
Thanks mate!
had the same
1. use computer (windows - in my case windows xp)
2. nokia cable is fine (i use it too)
3. use kf utility .6
is your kf recognized by the computer ? (adb device or composite adm device)
have you tried to shutdown and startup your computer ? (not restart)
the entry for 18D1 in adb_usb.ini is missing - had to add it
the other entries are allready in version .6 android_winusb.inf
if you have troubles to remove old drivers use this:
http://support.microsoft.com/kb/315539/en-us
unplug/replug and install the drivers from .6 from scratch
it's not needed to reboot the computer - works immediately
waiting to get your status ...
b63 said:
had the same
1. use computer (windows - in my case windows xp)
2. nokia cable is fine (i use it too)
3. use kf utility .6
is your kf recognized by the computer ? (adb device or composite adm device)
have you tried to shutdown and startup your computer ? (not restart)
waiting to get your status ...
Click to expand...
Click to collapse
Did you solve your problem?
My kindle is recognized by my computer but it as either ADB device or Composite ADB device (depending on what drivers I use to install it). Problem is that it says Cannot start device. Code Error: 10. Tried shutting down/restarting PC, still the same.
updated my initial post again ... (ms-link)
yes solved it in minutes
make the additional entry in adb_usb.ini
use only the drivers from .6
i think best way is to disconnect the kf - uninstall all old drivers regarding adb device - connect kf - use only drivers from .6 utility - start utility - change bootmode - up again !
whats your status ?
i think best way is to disconnect the kf - uninstall all old drivers regarding adb device - connect kf - use only drivers from .6 utility - start utility - change bootmode - up again !
Click to expand...
Click to collapse
I did this but it still says device cannot be started.
make the additional entry in adb_usb.ini
Click to expand...
Click to collapse
0x18D1 -- is that what I'm supposed to add to adb_usb.ini?
yes exactly - the device changes between the two id's regarding the bootmode
and don't let the computer select the driver - select manually
b63 said:
yes exactly - the device changes between the two id's regarding the bootmode
and don't let the computer select the driver - select manually
Click to expand...
Click to collapse
Okay, so I followed the instructions to a T.
I followed the MS Link to remove all drivers and then plugged-in the kindle and installed it back again by specifically telling windows that 'I have a disk'. It still says Code 10.
If it would mean anything, I'm doing this on a virtual machine since the computers around me are all Windows 7s.
kaswistry said:
Okay, so I followed the instructions to a T.
I followed the MS Link to remove all drivers and then plugged-in the kindle and installed it back again by specifically telling windows that 'I have a disk'. It still says Code 10.
If it would mean anything, I'm doing this on a virtual machine since the computers around me are all Windows 7s.
Click to expand...
Click to collapse
all this works using windows 7
dustyjerran said:
all this works using windows 7
Click to expand...
Click to collapse
I did try this yesterday on Windows 7 but most guides I see do it on older versions. I will try again a little later. Thank you.
I tried it on Windows 7. Still the same error. Kindle is frozen and on Device Manager it says "This device cannot start. (Code 10)"
I ran into the exact problem yesterday. I thought I bricked my kindle. That was scary. Anyway, the problem is that you're stuck on fastboot, mode 4002 instead of a normal mode 4000.
Following rootzwiki.com/topic/12363-how-to-windows-install-twrp-20-on-your-kindle-fire/
You'll need to add a new vendor id (0x18d1). However, even with that the device still will not be recognized right away. Following another user's suggestion on that same thread, I let the battery drained out. Once that's done, reconnecting the Kindle will show up as simply "kindle" on the device manager instead of the normal "unrecognized device".
Then do the adb commands (even if it doesn't show any device attached)
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
Click to expand...
Click to collapse
Your device will reboot out of the stuck "kindle fire" logo screen. If your device goes dark after, it just means that the battery need to recharged first. Another scary moment for me. You can unplug and use the wall charger, much faster than charging by PC. After 5 - 10 minutes, you should get back to your normal screen. Then, just use the Kindle Utility to install TWRP.
You'll need to add a new vendor id (0x18d1).
Click to expand...
Click to collapse
I added this already
reconnecting the Kindle will show up as simply "kindle" on the device manager instead of the normal "unrecognized device".
Click to expand...
Click to collapse
Actually, the problem with mine is that it's detected. However, it shows up as Code:10, The device is unable to start.
Still, I'll try to drain it first, tinker with it next and see what happens. That or I'll wait for tomorrow and open the whole device already and see if I can OMAP it.
Mine also did show up as code 10, and sometimes code 43 ... I tried uninstalled the driver and reinstall it manually each time and eventually showed up as unrecognized ... so I tried the battery drain ... I even tried putting it in the freezer to quicken the drain but not sure if it actually help ..
I tried the battery draining. Nope, still didn't work
UPDATE: I take this back. After draining the battery, I would like to confirm that the issue has been fixed. Thank you, THANK YOU Everyone! )
I REALLY APPRECIATE THE EFFORT. HAPPY HOLIDAYS! )
A family member recently got a Kindle Fire, I tried to flash recovery but it got stuck in fastboot mode. Windows will recognize it as uknown device but Linux won't detect anything in fastboot or adb.
I will try battery drain out since kaswistry said it worked
If all else fails, I will try this.. http://forum.xda-developers.com/showthread.php?t=1405052
EDIT: nevermind lol, this worked.. http://forum.xda-developers.com/showpost.php?p=20619033&postcount=11 even though i tried it several times already..
I have the same problem too, the kindle fire stuck at the boot logo
kf utility show that when i try to restore or other option!
Changing bootmode doesent work at all
*imageshack/photo/my-images/10/60506677.png/[/url] (imageshack link)
KF utility status fastboot... offline
*imageshack/photo/my-images/834/kfustatus.png/
My computer have the right driver!
can anybody help me?
*sorry for my bad english*
Could it be that something destroyed my FireFireFire boot? My KF always gets stuck in fastboot when I try to flash ... obviously quite annoying.
u guys need to talk to vashypool in irc and he can fix it!! he fixed mine and mine was a complete brick
If it gets stuck in fastboot you need to run the command fastboot idme bootmode 4000 from the Android SDK.
Sent from my Kindle Fire using Tapatalk
In my case, i have tried to install the original 6.2 kindle firmware with TWRP. After that, the kindle staying stuck on the boot logo... This is me story... I think my kindle is stuck on fastboot! I tried to change bootmod with FK utility v.6
This is what kf utility gave me, when i try to reinstall twrp
imageshack.us/photo/my-images/10/60506677.png/
And this is the kf utility status
imageshack.us/photo/my-images/834/kfustatus.png/
Is anybody can say me, if my kindle is bricked for ever? Or have a solution
Happy holiday btw
#sorry for my poor english#
Related
okay so i was trying to root my kindle fire and i didnt get su any where so then i tryed to install cwm and now its stuck at the yellow triangle and it wont go into recovery and it also will not connect to adb i need hellp ASAP
Install drivers as ADB composite with the Android SDK and then use this to change the bootmode
The link you posted is not working due to the period in the URL at the end.
Do not afraid. I have got the same experience Let God bless the search button
http://forum.xda-developers.com/showthread.php?t=1568340
unzip fbmode.zip
adb push fbmode /data/local/fbmode
adb shell chmod 755 /data/local/fbmode
adb shell /data/local/fbmode
adb reboot
Your kindle will "get stuck" on the kindle fire screen, but really it's just in fastboot mode.
fastboot -i 0x1949 boot twrp-blaze-2.0.0RC0.img
Your device will now boot into twrp recovery, and flash the firefirefire bootlaoder. When done it will prompt you to reboot. Upon reboot you will get stuck on the "yellow triangle" screen of firefire fire.
fastboot oem idme bootmode 5002
fastboot reboot
Click to expand...
Click to collapse
My kindle got the 6.3 update -solved!!
This has got to be one of the fastest ways I have rooted 6.3 kindle update
i went on line here http://liliputing.com/2012/03/root-...ogle-play-store-with-kindle-fire-utility.html
downloaded the new kindle fire utility and ckick on Install permanent root with super user. got rooted in about 2 minutes with no trouble at all
thanks everyone for your help but i solved it what i was doing was unsing the kindle fire utility trying to instal latest firefirefire but it just sat there and so i just went into the utility and reinstaled the twrp and it booted normal!!
Bricked Kindle
Okay, I'm not having the same issue, but I'm pretty sure I've completely, irevicalbly, bricked my kindle.
I know that I'm not in Fastboot mode, I've experienced that issue and solved it with the KFU.
Here's what I did:
I used the KFU to root my kindle. That worked fine. I was able to load all the Google apps (which was my initial goal). Then, I got greedy and decided that ICS was my next step - oops.
I followed the instructions on the following site:
androidauthority.com/kindle-fire-miui-4-ics-55853/
Note: I know, I'm an idiot - I should have paid attention to comments! UGH!
After I did this, I now only get the firefirefire logo and that is it. I can't load/reload TWRP and I can't change my bootmode to normal or recovery. The thing is, no matter which computer I plug the device into, the computer won't recognize the device. I get a message saying something "malfunctioned" when I plug it in. I've tried 3 different Windows machines (I've installed/reinstalled drivers I don't know how many times!) and I even tried loading Linux on a spare laptop and that didn't work either.
So, I tried the next thing I could think of. I followed the instructions on the following site:
ramble.karrth.com - Section "Troubleshooting TWRP
which involved removing the back cover, shorting a circuit (to force usbboot) and plugging my Kindle in. This didn't work for me either.
At this point, I'm willing to try anything. I'm not quite sure how to fix this issue. I think my next step is to either order a factory cable or make my own and try that, but if my bootloader is broke (truely broke) will that even work?
Please, if I should post this in another forum/place, just let me know. Any help appreciated!
I should also not that nothing comes up in my device manager. It does come up as a unrecognized USB bit goes away after telling me there was a malfunction.
ChrisKenison said:
I should also not that nothing comes up in my device manager. It does come up as a unrecognized USB bit goes away after telling me there was a malfunction.
Click to expand...
Click to collapse
If you get the yellow triangle logo to come up, then it's probably in fastboot mode. If you reboot it while it's connected to your computer and you get some device detection beeps from Windows, it's likely to be a driver issue. Look here...
http://forum.xda-developers.com/showpost.php?p=23747671&postcount=2
You might want to read the first post in that thread too.
Watch carefully as the device boots up and you get the yellow triangle logo. If that boot logo comes up and stays there, it's in fastboot. If the boot logo comes up, the screens blacks out, and then the boot logo comes back up (dimmer) then it's either trying to get into recovery or booting into the OS and failing.
I would try setting the bootmode to normal in KFU and when it says "<waiting for device>" reboot the Kindle Fire. Since you have FFF, the fastboot program on your computer will wait for the Kindle Fire's FFF bootloader to get into temporary fastboot and reset the bootmode when the KF is ready.
But, the computer won't even recognize there is a device connected to it
I will have to try installing the drivers from the Android SDK... maybe that will turn up something. But, by installing the drivers from KFU, it doesn't work.
When I plug the device in, it beeps at me saying device is unrecognize and it couldn't install drivers because there was a malfunction. In the device manager (while that's happening) it shows up as an unrecognized usb device. Then, it goes away (the device doesn't stay in the device manager). Then, that whole thing happens again one more time. There isn't anything for me to update in the device manager... thoughts?
And because its not recognized in the device manger, kfu isn't picking it up
Sent from my Galaxy Nexus using xda premium
ChrisKenison said:
I will have to try installing the drivers from the Android SDK... maybe that will turn up something. But, by installing the drivers from KFU, it doesn't work.
When I plug the device in, it beeps at me saying device is unrecognize and it couldn't install drivers because there was a malfunction. In the device manager (while that's happening) it shows up as an unrecognized usb device. Then, it goes away (the device doesn't stay in the device manager). Then, that whole thing happens again one more time. There isn't anything for me to update in the device manager... thoughts?
Click to expand...
Click to collapse
If you can't get the drivers working with the KFU distribution, you'll have a harder time with the SDK. They are the same drivers, but KFU has an updated, Kindle Fire specific .inf file for the driver and also installs the .ini file in the .android folder that you'll need. I don't know what you see in the device manager, but if you don't get one of the devices shown in the post I referred to earlier, I would try another Windows machine. You won't be able to do anything without getting it to detect your KF and load the proper drivers. If you are more adventurous, you could try pokey9000's Firekit (search for it) and try using linux to send it fastboot commands.
Yeah, that's my problem. I have tried 3 different windows machines (all windows 7) and, being the adventurous person i am I tried the Linux fix (removing back cover...) to no avail. All that did was make my kindle blink green. Not sure what that means either.
yea mine is stuck on the firefirefire boot screen
ChrisKenison said:
Yeah, that's my problem. I have tried 3 different windows machines (all windows 7) and, being the adventurous person i am I tried the Linux fix (removing back cover...) to no avail. All that did was make my kindle blink green. Not sure what that means either.
Click to expand...
Click to collapse
Well, if you can't get any of those scenarios to work out, maybe it's a hardware issue. It might be something as simple as a bad USB cable or something more serious within the KF itself. I've never had a problem with Windows or Linux not seeing the KF, so my hands on experience in this regard is limited... my KF has never been broken to that degree. I'm always curious to see what's going on with people's KF when they say nothing works, but my KF has never given me that opportunity.
ChrisKenison said:
I will have to try installing the drivers from the Android SDK... maybe that will turn up something. But, by installing the drivers from KFU, it doesn't work.
When I plug the device in, it beeps at me saying device is unrecognize and it couldn't install drivers because there was a malfunction. In the device manager (while that's happening) it shows up as an unrecognized usb device. Then, it goes away (the device doesn't stay in the device manager). Then, that whole thing happens again one more time. There isn't anything for me to update in the device manager... thoughts?
Click to expand...
Click to collapse
Sometimes in order to install the correct driver you need to delete the original from your computer because it will continue to attempt to revert to the default but beforehand try rebooting your computer and the kindle
---------- Post added at 07:41 PM ---------- Previous post was at 07:39 PM ----------
mistaanime said:
yea mine is stuck on the firefirefire boot screen
Click to expand...
Click to collapse
Run the kf utility again install twrp and fff again
So, I tried searching for days on how to fix my problem.
A little while ago I rooted my Kindle Fire, and it was great. Then I did something. Not sure exactly what. But It ended up just doing nothing. When I boot up the Kindle it shows the blue and white Kindle Fire logo. Nothing else past that (unless I go to recovery.) Now, my computer doesnt recognize it anymore, even after doing most of the driver updates that people on here have said to do.
I need help, basically, getting it back to normal, so I can give rooting a try again. Now that I know what exactly I am dealing with, I can do this and not screw everything up.
First, the computer says the driver is installed, yet it doesnt recognize it.
Second, (before the driver mishap) KFU said it was connected but the adb was unknown.
Third, I have CWM and I tried to flash the normal Amazon update to bring it back, and it says"it cant open it (bad)".
Now, I would really like some help with this. I'm just at a complete lost.
Now should I put that into command prompt in the adb part? because it just says fastboot is not recognized.
Yes, It wont do that, it just says error: device not found. also says 'fastboot' is not recognized.
Now its just not connecting to the computer. I installed Android sdk and everything and its just not working. It says the driver is installed but there was an error because a problem had occurred. Any help? :crying:
As soon as you get tired messing with drivers you can move on to something that works http://forum.xda-developers.com/showthread.php?t=1850038
ManofFishFry said:
Yes, It wont do that, it just says error: device not found. also says 'fastboot' is not recognized.
Click to expand...
Click to collapse
I hope u r on windows PC..
first after u set up adb, make sure u install adb drivers that came with kindle fire utility with ur kindle fire unplugged..if u had plugged in kindle fire while doing that, go to device manager and uninstall that device and its driver software and start up from beginning..
keep kf unplugged and install driver..u dont get usb debugging option in stock kf rom..its enabled if u have installed the drivers properly..ur kindle fire appears as android phone in device manager if everything u hav done is correct..
then boot up ur kf..that blue and white kf logo is of firefirefire bootloader..i hope its v1.4a and u see it on right top of the screen..if its stuck there then open command prompt as administrator on ur pc..connect ur kf to pc..type in to cmd
Code:
fastboot devices
if u see something under list of devices attached that will be ur kindle fire(unless some other android device is connected in fastboot mode lol)
Because kindle fire, as far as i know, can only boot into 3 bootmodes(normal, recovery, fastboot) unless u have altered the partition table to install different roms and multiboot ur kindle fire..
if fastboot command is not recognized, try setting the path to where fastboot.exe is present in KFU folder
alternatively u can go to folder where fastboot.exe is located and right click while holding shift and selecting 'open command window here' and fastboot needs to firefirefire bootloader to be installed on ur kindle fire..
also u can try this..
JUST GO TO RECOVERY..twrp has always been a better recovery software than cwm based thing available for kindle fire at least for me..if u go to recovery, ur kf will definitely show up as an adb device..u can change the bootmode using this..just type in:
Code:
adb devices
if ur kf is seen as in recovery then type this in cmd
Code:
idme bootmode 4000
reboot
just report if this worked..
okay well, I deleted all the drivers and started from the beginning. Yet, after running the install_driver.bat I plugged my Kindle in and it still says device not recognized. Now, you how can get adb working? It is coming up as unknown device. Its just seeming like theres something wrong on the kindle part. But hey, what do I know. haha
lol try what will work http://forum.xda-developers.com/showthread.php?t=1850038
But doesn't that require linux? I have windows 7. Is there something like that for windows?
Thepooch said:
lol try what will work http://forum.xda-developers.com/showthread.php?t=1850038
Click to expand...
Click to collapse
Hi i have the same problem but the only thing is that my device is actually verified by the coputer and can connect via usb mount but when i try to install a ROM it says unable to mount and cannot install rom but i see there is something for fixing mounting problems there in soupkit so i'll give it a try.
This is what I get when I try to install the driver....
To run soupkit all you need is at least a 2 gig usb flash drive ubuntu 12.04 32 bit and universal usb creator. By the way your problem with the driver is you (or how you`re going about it), You would trip if I got on your computer and got it to work or could at least tell you why its not working. that`s why I suggested soupkit if you would of actually read the information I gave you, I wouldn`t have had to tell you twice and you would know that to use it it`s not required to be installed on your computer. But hey catch me online I can either help you fight through windows crappy drivers or help you set up soupkit I`m always game for a challenge When updating the driver you need to point it to the 32 bit version of the driver for instance on my computer it`s located here C:\Documents and Settings\HP_Administrator\Desktop\Kindle_Fire_Utility_v0.9.6\Kindle Fire Utility\drivers. After it`s ran unplug and replug device if that doesn`t work power off and power on while connected this generally does the trick when windows finally catches on it will install android adb interface, this is the fastboot driver (if you`re stuck in fastboot). Then select option 1 in KFU for changing bootmodes, then option 1 for normal if it does nothing power off and power on while connected it should then detect the kindle and reset the bootmode to normal. Pm me later I will be online all evening and most every evening I will help you sort it out.
Josepho1997 said:
Whoops! Somehow my post was posted twice. I didn't even get to see your reply. Sorry!
Sent from my Kindle Fire using xda premium
Click to expand...
Click to collapse
this is what I get when I try this... (btw im working with firefirefire. its got the blue and white kindle fire.)
Why don't you let me take a look?
Dark__king said:
Hi i have the same problem but the only thing is that my device is actually verified by the coputer and can connect via usb mount but when i try to install a ROM it says unable to mount and cannot install rom but i see there is something for fixing mounting problems there in soupkit so i'll give it a try.
Click to expand...
Click to collapse
Yes soupkit can fix mounting problems.
This is a very interesting issue with this Kindle windows detects it as unknown usb device, drivers are installed properly from what I can see. Ubuntu with soupkit ran on it fails to detect it in recovery or fastboot. multiple cables tried, lsusb doesn`t show the device connected. I really think this one the computer is the problem, because it`s the only unchanged variable.
Firekit may be the only option if Linux won't detect the device. Before doing that, make sure a USB 3.0 port isn't being used and try a fresh install of Linux to be safe. Otherwise, it seems putting it in USBboot is the only option for getting Linux to detect.
I'm not exactly sure what causes the unknown device error, but it almost always means there is something wrong with the bootloader, and it seems as though Windows might be the main culprit. Not sure why exactly, but it may be similar to the problem soulweeper51 had. Possibly a hardware issue involving the computer's USB port or the motherboard itself.
@ManoFishFry has doomlords cwm recovery and he flashed JB at first I thought it was an issue with cwm not being detected but the fact that it`s not detected in fastboot raised my eyebrows. The bootloader appears to be functional but I cannot rule out any minor state of being broken in another fashion when lsusb returns null. The computer doing the work had never been used prior to the incident so driver install didn`t take place till after the fact. The usb ports are all either 1.0 or 2.0 no 3.0 ports are being used. An alternate computer would be nice to rule out the computer itself @ManoFishFry only has a dinosour of an xp machine as alternate use of is not possible yet, not that it would even be possible to install drivers because of the typical unsigned driver failure of xp and booting ubuntu isn`t happening at the moment on this machine.
I'm willing to bet it is the bootloader.
Just USBboot and get it over with.
We did try usb boot once but it didn`t work will keep trying.
Hey guys... Only second kindle I've ever attempted (have a butyload of other android devices I've rooted... But this bigger with no other buttons has me stumped )
Anyway... Went to root today, plugged in kindle, battery was dead... No problem... Let it charge.
When it booted, ran KFU to tell it to install TWRP. Here's where it gets....odd.
I had twrp in the KFU folder but it decided it wasn't there and wanted to download it... Mind you, this is... I believe... After it sent a command to fastboot ... Well, I didn't have internet, so KFU just sort of stopped when it couldn't download twrp...
Since then, the kindle is just stuck on KindleFire screen... Doesn't go any further... If I let the battery run out for about an hour, it will start rebooting every 5 seconds even if I plug it in. In the "bootloop" I can't turn it off, it just keeps rebooting...
If I let it die, I can plug it in, let it charge and turn it on... Sticks at KindleFire screen... I have tried holding in power for 30 seconds... It just turns the kindle off, doesn't help.
Windows sees it as an unrecognized device (tried rebooting, unplugging, uninstalling the drivers, looking at the KFU folder to manually select drivers (windows says they're not the correct drivers for the device) adv can't see it (cms... Adb devices shows no devices connected)
Any help is appreciated... If I missed needed info, please ask and ill supply...
I'm happy to try anything and report the findings...
RBThompsonV said:
Hey guys... Only second kindle I've ever attempted (have a butyload of other android devices I've rooted... But this bigger with no other buttons has me stumped )
Anyway... Went to root today, plugged in kindle, battery was dead... No problem... Let it charge.
When it booted, ran KFU to tell it to install TWRP. Here's where it gets....odd.
I had twrp in the KFU folder but it decided it wasn't there and wanted to download it... Mind you, this is... I believe... After it sent a command to fastboot ... Well, I didn't have internet, so KFU just sort of stopped when it couldn't download twrp...
Since then, the kindle is just stuck on KindleFire screen... Doesn't go any further... If I let the battery run out for about an hour, it will start rebooting every 5 seconds even if I plug it in. In the "bootloop" I can't turn it off, it just keeps rebooting...
If I let it die, I can plug it in, let it charge and turn it on... Sticks at KindleFire screen... I have tried holding in power for 30 seconds... It just turns the kindle off, doesn't help.
Windows sees it as an unrecognized device (tried rebooting, unplugging, uninstalling the drivers, looking at the KFU folder to manually select drivers (windows says they're not the correct drivers for the device) adv can't see it (cms... Adb devices shows no devices connected)
Any help is appreciated... If I missed needed info, please ask and ill supply...
I'm happy to try anything and report the findings...
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2166668
#30 & #31
soupmagnet said:
http://forum.xda-developers.com/showthread.php?t=2166668
#30 & #31
Click to expand...
Click to collapse
OK... but why does it stick on the KindleFire logo? (It does that without rebooting, it just hangs there).. And the battery drain was not intentional... It's ff now... charging (I assume... no logo, no led )
RBThompsonV said:
OK... but why does it stick on the KindleFire logo?
Click to expand...
Click to collapse
#16
It's ff now... charging (I assume... no logo, no led )
Click to expand...
Click to collapse
I would have to agree...it does appear to be charging.
soupmagnet said:
#16
I would have to agree...it does appear to be charging.
Click to expand...
Click to collapse
Sorry if im being super-noobish... I prefer my nook over this kindle
The logo is bright and unchanging (Seems to be stuck in fastboot?) But adb doesnt recognize it... windows sees it as an unknown device... and KFU shows... well, nothong Even when I try to normal boot in KFU (or adb..) it hangs on waiting for device.
Also, thanks a billion for even responding Soup... Its nice to know there's someone out there
RBThompsonV said:
Sorry if im being super-noobish... I prefer my nook over this kindle
The logo is bright and unchanging (Seems to be stuck in fastboot?) But adb doesnt recognize it... windows sees it as an unknown device... and KFU shows... well, nothong Even when I try to normal boot in KFU (or adb..) it hangs on waiting for device.
Also, thanks a billion for even responding Soup... Its nice to know there's someone out there
Click to expand...
Click to collapse
Okay,
Yes, it is in fastboot. ADB won't recognize the device in fastboot because ADB commands don't work in fastboot, only fastboot commands will. The KFU won't detect the device in fastboot because of the bootloader itself. It used to, but not anymore...likely due to an update on Amazon's part. There can be a couple of reasons why it just hangs at "waiting for device". When you see "waiting for device", you can reboot the KF and see if it detects upon rebooting. If not, you'll have to completely uninstall your drivers and try again. Even then, there's still a good chance it won't work. If not, you can reference the following thread for clues to get it working properly:
http://forum.xda-developers.com/showthread.php?t=2179748
soupmagnet said:
Okay,
Yes, it is in fastboot. ADB won't recognize the device in fastboot because ADB commands don't work in fastboot, only fastboot commands will. The KFU won't detect the device in fastboot because of the bootloader itself. It used to, but not anymore...likely due to an update on Amazon's part. There can be a couple of reasons why it just hangs at "waiting for device". When you see "waiting for device", you can reboot the KF and see if it detects upon rebooting. If not, you'll have to completely uninstall your drivers and try again. Even then, there's still a good chance it won't work. If not, you can reference the following thread for clues to get it working properly:
http://forum.xda-developers.com/showthread.php?t=2179748
Click to expand...
Click to collapse
OK.. Ive tried everything in the thread... Only thing I cant find is the android_winusb folder (Im running Win7 x64).
Also, when I look up the UNKNOWN DEVICE Hardware ID, I get USB\UNKNOWN) in device manager
RBThompsonV said:
OK.. Ive tried everything in the thread... Only thing I cant find is the android_winusb folder (Im running Win7 x64).
Also, when I look up the UNKNOWN DEVICE Hardware ID, I get USB\UNKNOWN) in device manager
Click to expand...
Click to collapse
Make sure you have the hardware IDs that I posted in that thread, in your KFU's 'android_winusb.inf' file.
You also have to find and delete the folder that gets created by KFU's install_drivers.bat. It will be in the WINDOWS directory somewhere, most likely in a hidden folder. Make sure "Show hidden folders" is enabled.
You may have to search your hard drive for any directory containing the string "android" OR for the filename 'android_winusb.inf',making sure to search hidden files and folders.
Once you have found and deleted it, reboot your computer and run KFU's newly edited 'install_drivers.bat'
Still Stuck...
OK, so, I did a CLEAN install of windows XP, installed the complete Android SDK package, then installed the modified KFU package (Added the lines of Device IDs supplied in your post on how to get it to work) and edited the install bat to install in legacy mode.
I still get an error in windows about the Kindle Fire.
I installed everything, then plugged in the kindle after turning it on. Kindle is still stuck on Kindle Fire logo (doesnt flicker or sparkle or dim or anything)... and windows says:
(In FOUND NEW HARDWARE WIZARD):
Cannot start this hardware
There was a problem installing this hardware:
Android Composite ADB Interface
This device cannot start (Code 10)
...
Thats a USB error code , maybe trying to use a different cable or use the usb ports on the back of the pc instead of the front
OMFG!!!!
I want to thank all of you for your help...
But, get this...
Apparently the kindle was waiting for me to send the TWRP package... THATS ALL!!!
I built the factory cable... proved useless for me
I went through all of my USB cables... NONE worked...
So, as a last ditch effort I thought... screw it, lets see what happens if I... (Fill in the blank)...
Tried sending the TWRP package and BAM!!!! Blue kindle...
Go figure
Hi. I am really in a jam here. I have read a lot of documentation and still am not getting anywhere. I bought my sister a Kindle Fire for her birthday, and after reading the Kindle Fire for Beginner's Guide, I was able to successfully install Cyanogenmod 10.1 It was working fine, but I gave it some thought and decided she would be better off with the stock software, so I followed the instructions here to revert.
However, somewhere in that process I bricked the device. I went through the installing the Amazon software again in TWRP and told the device to reboot, but it is now stuck on the boot screen and will not respond to adb commands I send it.
I used the Kindle Fire Utility to install TWRP again, and it said it was successfully installed. I tried to boot into it through the Kindle Fire Utility menu, but it is still stuck.
It just so happens that I have a fastboot cable for this, so I plugged it in and tried to boot into recovery by issuing
C:\kfu\tools>fastboot oem idme bootmode 5001
It just says:
<waiting for device>
and nothing happens.
I don't know what else to do. I do think this factory cable put me in fastboot mode because the Windows device manager is showing "Android ADB Interface" (which according to Kindle Fire for Beginners is what it is supposed to say if the drivers are good and I am in fastboot mode), but I do not know how else to make use of this.
I am really stuck here, and I hope someone will take the time to help. My sister's birthday is in two days and I need to get this Kindle fixed and in the mail
farkuldi said:
Hi. I am really in a jam here. I have read a lot of documentation and still am not getting anywhere. I bought my sister a Kindle Fire for her birthday, and after reading the Kindle Fire for Beginner's Guide, I was able to successfully install Cyanogenmod 10.1 It was working fine, but I gave it some thought and decided she would be better off with the stock software, so I followed the instructions here to revert.
However, somewhere in that process I bricked the device. I went through the installing the Amazon software again in TWRP and told the device to reboot, but it is now stuck on the boot screen and will not respond to adb commands I send it.
I used the Kindle Fire Utility to install TWRP again, and it said it was successfully installed. I tried to boot into it through the Kindle Fire Utility menu, but it is still stuck.
It just so happens that I have a fastboot cable for this, so I plugged it in and tried to boot into recovery by issuing
C:\kfu\tools>fastboot oem idme bootmode 5001
It just says:
<waiting for device>
and nothing happens.
I don't know what else to do. I do think this factory cable put me in fastboot mode because the Windows device manager is showing "Android ADB Interface" (which according to Kindle Fire for Beginners is what it is supposed to say if the drivers are good and I am in fastboot mode), but I do not know how else to make use of this.
I am really stuck here, and I hope someone will take the time to help. My sister's birthday is in two days and I need to get this Kindle fixed and in the mail
Click to expand...
Click to collapse
First, welcome to Xda-developers
OK. So lets cover the basics.
http://forum.xda-developers.com/showthread.php?t=1428428
^ Download and run that tool. Its very useful for un-bricking your Kindle
Once that is done, reboot into recovery and wipe every things. (sorry, we're going to start you from fresh start)
I'm going to suggest you try to install this ROM
http://forum.xda-developers.com/showthread.php?t=2103278
The reason being that this one will give you the option to also wipe a few other places (including boot)
Now assuming you still want to keep with stock
http://forum.xda-developers.com/showthread.php?t=2211872
This is basically the stock ROM by its rooted.
Socially Uncensored said:
First, welcome to Xda-developers
OK. So lets cover the basics.
http://forum.xda-developers.com/showthread.php?t=1428428
^ Download and run that tool. Its very useful for un-bricking your Kindle
Once that is done, reboot into recovery and wipe every things. (sorry, we're going to start you from fresh start)
I'm going to suggest you try to install this ROM
http://forum.xda-developers.com/showthread.php?t=2103278
The reason being that this one will give you the option to also wipe a few other places (including boot)
Now assuming you still want to keep with stock
http://forum.xda-developers.com/showthread.php?t=2211872
This is basically the stock ROM by its rooted.
Click to expand...
Click to collapse
Thank you for your reply! I ran the Kindle Fire unbrick tool with the option "Stuck at logo," and it said "Congratulations, your Kindle should be unbricked. However, nothing had changed. So I ran it with the option "Other . . ." It said:
Code:
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
This part might take a while . . .
< waiting for device >
I have left it like that for ten minutes now and nothing is happening. Do you think it is working? I'll leave it alone for an hour or so I guess but I'm wondering.
BTW, for this I just used a regular USB cable and not the factory one. Is that right?
Thanks!
farkuldi said:
Thank you for your reply! I ran the Kindle Fire unbrick tool with the option "Stuck at logo," and it said "Congratulations, your Kindle should be unbricked. However, nothing had changed. So I ran it with the option "Other . . ." It said:
Code:
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
error: device not found
This part might take a while . . .
< waiting for device >
I have left it like that for ten minutes now and nothing is happening. Do you think it is working? I'll leave it alone for an hour or so I guess but I'm wondering.
BTW, for this I just used a regular USB cable and not the factory one. Is that right?
Thanks!
Click to expand...
Click to collapse
The unbrick program didn't work. It just stayed there t <waiting for device>. How can I use the fastboot cable to fix it?
Thanks.
I had the same problem before. It always says no device found. I tried different PC, finally in my XP PC it is detected and new ROM flashed in
Maybe you should try different PC
ezproxy said:
I had the same problem before. It always says no device found. I tried different PC, finally in my XP PC it is detected and new ROM flashed in
Maybe you should try different PC
Click to expand...
Click to collapse
I was thinking the same thing. Unfortunately I don't have another PC running Windows. All my others are running Linux, and I don't know how to get the drivers working.
I think I will borrow a laptop from a friend tomorrow and see if it works. It is my sister's 17th birthday today and her present is late!
In the meantime, though, does anyone know how I am supposed to use this fastboot cable? I have looked around and I see a lot of tutorials about how to unbrick without a fastboot cable, but none saying how to do it WITH one. I thought the cable was supposed to make it easier?
Thanks for the help.
farkuldi said:
I was thinking the same thing. Unfortunately I don't have another PC running Windows. All my others are running Linux, and I don't know how to get the drivers working.
I think I will borrow a laptop from a friend tomorrow and see if it works. It is my sister's 17th birthday today and her present is late!
In the meantime, though, does anyone know how I am supposed to use this fastboot cable? I have looked around and I see a lot of tutorials about how to unbrick without a fastboot cable, but none saying how to do it WITH one. I thought the cable was supposed to make it easier?
Thanks for the help.
Click to expand...
Click to collapse
First of all, Happy Birthday to your sister!
I think you may need install the firefirefire utility first to help you out of bootmode sucking. After you successfully reinstall the TWRP using unbrick utility, you need change the fastboot mode to normal boot, the firefirefire can help you choose,
here is the information may help you : http://forum.xda-developers.com/showthread.php?t=1668159
ezproxy said:
First of all, Happy Birthday to your sister!
I think you may need install the firefirefire utility first to help you out of bootmode sucking. After you successfully reinstall the TWRP using unbrick utility, you need change the fastboot mode to normal boot, the firefirefire can help you choose,
here is the information may help you : http://forum.xda-developers.com/showthread.php?t=1668159
Click to expand...
Click to collapse
I'd say you didn't read the previous posts.
Well, now the Kindle Fire is no longer being recognized by my computers. I borrowed another Windows computer like I said I would, but when I plug in the Kindle, the Device Manger does not even register it. Also, usually when I plug it in, the computer will realize I have plugged in a usb device and respond with that little pop up at the task bar, i.e. to let me know it sees a usb device and is trying to install driver, was not able to install drivers, or whatever. But now nothing. The computer doesn't even see it.
I have tried it on two different computers with three different cables and it's the same thing. I have restarted the computer and reinstalled the drivers over and over again and there is no difference. What is going on? It was seeing the Kindle fine before I tried the Unbricking Utility.
farkuldi said:
Well, now the Kindle Fire is no longer being recognized by my computers. I borrowed another Windows computer like I said I would, but when I plug in the Kindle, the Device Manger does not even register it. Also, usually when I plug it in, the computer will realize I have plugged in a usb device and respond with that little pop up at the task bar, i.e. to let me know it sees a usb device and is trying to install driver, was not able to install drivers, or whatever. But now nothing. The computer doesn't even see it.
I have tried it on two different computers with three different cables and it's the same thing. I have restarted the computer and reinstalled the drivers over and over again and there is no difference. What is going on? It was seeing the Kindle fine before I tried the Unbricking Utility.
Click to expand...
Click to collapse
I'm assuming you know for sure this was a 1st Generation Kindle, right?
I had this problem once and basically formatted my computer. The driver was the issue and I couldn't uninstall it completely. Using my drivers solved this. I get the feeling you're still trying to use the drivers that came with the utility (don't they're often trouble)
However, assuming you are using the correct drivers (the ones I linked for you).... Boot into TWRP and wipe everything. Don't just use the general, click the advance options and wipe everything (selecting all options manually).
No connect your Kindle and don't worry about it not showing up yet....
Mount your SSD (should suddenly find your kindle) and upload this ROM
http://forum.xda-developers.com/showthread.php?t=2211872
Now if you can't even load TWRP (when you turn on the Kindle, you'll need to hold the power button to bring up the menu, then quickly hit it a few times until its on recovery).... But if you can't load TWRP at all, its time to get a factory cable.
If you have a factory cable and still can't find the device (and assuming you're using the right drivers, on a fresh install) .... As someone else who knows how to do this. Because past that, all hope is lost.
Socially Uncensored said:
I'm assuming you know for sure this was a 1st Generation Kindle, right?
I had this problem once and basically formatted my computer. The driver was the issue and I couldn't uninstall it completely. Using my drivers solved this. I get the feeling you're still trying to use the drivers that came with the utility (don't they're often trouble)
However, assuming you are using the correct drivers (the ones I linked for you).... Boot into TWRP and wipe everything. Don't just use the general, click the advance options and wipe everything (selecting all options manually).
No connect your Kindle and don't worry about it not showing up yet....
Mount your SSD (should suddenly find your kindle) and upload this ROM
http://forum.xda-developers.com/showthread.php?t=2211872
Now if you can't even load TWRP (when you turn on the Kindle, you'll need to hold the power button to bring up the menu, then quickly hit it a few times until its on recovery).... But if you can't load TWRP at all, its time to get a factory cable.
If you have a factory cable and still can't find the device (and assuming you're using the right drivers, on a fresh install) .... As someone else who knows how to do this. Because past that, all hope is lost.
Click to expand...
Click to collapse
Hi, My name i Jonah and i have a Kindle fire (5th generation) That came stock with Amazon's Fire OS Bellini 5.1.1. I tried to flash Cm12 with the app FlashFire (https://www.youtube.com/watch?v=NaCBSuUuhRE&spfreload=10) and during the installation i noticed it stopped for a while and didnt do anything. So i waited then 10 minutes later i decided to turn it off and turn it back on to fix it, when it started to boot up it showed the Cm logo just like as if it was running Cm12. So i waited, maybe 5 min at the most and it still would not turn on. So i turned it off, went online to see ho to get out of a bootloop. Rootjunky said to Turn your Kindle off and run ADB and Fastboot as a command from where you installed your drivers. Then he said he said to enter Recovery mode by pressing vol down and the power button. It is suppose'd to say Recovery-Mode in the corner but it just kept showing the Amazon logo. Im worried i screwed up and broke my new tablet, i can't return it because it's against Amazon's policy to root or mod any content of Amazon's, Plus ADB isn't working i can only access fastboot. I tried fixing it with the stock charger also but how do i know what kind of Android charger should i use?
Gon Rouge said:
Hi, My name i Jonah and i have a Kindle fire (5th generation) That came stock with Amazon's Fire OS Bellini 5.1.1. I tried to flash Cm12 with the app FlashFire (https://www.youtube.com/watch?v=NaCBSuUuhRE&spfreload=10) and during the installation i noticed it stopped for a while and didnt do anything. So i waited then 10 minutes later i decided to turn it off and turn it back on to fix it, when it started to boot up it showed the Cm logo just like as if it was running Cm12. So i waited, maybe 5 min at the most and it still would not turn on. So i turned it off, went online to see ho to get out of a bootloop. Rootjunky said to Turn your Kindle off and run ADB and Fastboot as a command from where you installed your drivers. Then he said he said to enter Recovery mode by pressing vol down and the power button. It is suppose'd to say Recovery-Mode in the corner but it just kept showing the Amazon logo. Im worried i screwed up and broke my new tablet, i can't return it because it's against Amazon's policy to root or mod any content of Amazon's, Plus ADB isn't working i can only access fastboot. I tried fixing it with the stock charger also but how do i know what kind of Android charger should i use?
Click to expand...
Click to collapse
post in correct forum
Fire Index: Which Amazon (Kindle) Fire Do I have?
"Failed - Virus detected" Chrome wouldn't let me open it - if you're for real, please re-post the software.
jerry777888 said:
"Failed - Virus detected" Chrome wouldn't let me open it - if you're for real, please re-post the software.
Click to expand...
Click to collapse
Repost what?
Sent from my ocean using XDA Labs
I am total noob. Just want to make that clear from the get go.
I hesitate to start a new thread, but I have been working on this forever, and have not made any progress.
I have a Kindle Fire that I would like to run android on - I started the process with the Kindle Fire Utility v 0.9.9. Something went wrong, and it is now stuck on the Kindle Fire start up logo. I also can no longer see it in the device manager, nor is it responsive to anything in the Utility. (ADB status: Offline Boot Status: Unknown). I am at a loss, does anyone have any ideas? Your help is appreciated!
.................FIGURED IT OUT!..............................
Much thanks to the pooch who spent hours helping me troubleshoot.
What we (he) did, as far as I remember, hopefully this can be of some service to someone else out there.
1) Figured out that trying all of this on a Virtual Machine is not a good idea!
2) I somehow broke the bootloader in my first attempt, so none of my computers were recognizing the KF.
3) Created a Pendrive to run Linux (ubuntu). Here Requires a USB drive formatted Fat16/Fat32/NTFS, minimum of 2 gb.
4) Once I got Linux running, installed SoupKit.
5) Went through a few tries of booting, rebooting, into recovery mode until the Kindle flickered back to life!
6) Followed prompts on SoupKit to install TWRP, updated TWRP, install FireFireFire, install Android 4.2.
Good luck, I am happy to answer any questions - though I am no means an expert now.
What I have tried...more info
More Information:
I am running Windows7 in a VirtualBox on an iMac.
I bricked the Kindle a few weeks ago, after messing with it then, I bought a factory fastboot cable. Still no dice.
I have tried all turning on and off computer, on and off Kindle with it disconnected, connected, going through the KFU 4 seconds after starting the Kindle. Letting the Kindle's battery die, recharging.
I have deleted .android folder, reinstalled drivers, re-downloaded KFU.
I have tried on a different computer (Windows XP) The Kindle is also not recognized there.
I have tried booting into Ubuntu (however in the directions there, it said the FireKit is for more "serious" issues than my soft brick.
I am sure there is some small detail I am missing, but I have not been able to find it - and I am not knowledgeable enough to properly diagnose the problem. Again thanks for any help.
kyleboyd said:
I am total noob. Just want to make that clear from the get go.
I hesitate to start a new thread, but I have been working on this forever, and have not made any progress.
I have a Kindle Fire that I would like to run android on - I started the process with the Kindle Fire Utility v 0.9.9. Something went wrong, and it is now stuck on the Kindle Fire start up logo. I also can no longer see it in the device manager, nor is it responsive to anything in the Utility. (ADB status: Offline Boot Status: Unknown). I am at a loss, does anyone have any ideas? Your help is appreciated!
Click to expand...
Click to collapse
Sometimes KFU will show as Unknown even though it's really fine. I had the same issue as you. Try switching boot mode to Normal and see if that fixes it, it worked for me.
Read this (everything),especially third post.
http://forum.xda-developers.com/showthread.php?t=1552547
hemmulde 1st
zastava750 said:
Read this (everything),especially third post.
http://forum.xda-developers.com/showthread.php?t=1552547
Click to expand...
Click to collapse
Thanks for the reply!
I tried that. When I type "fastboot getvar product" it says waiting for device or something similiar.
The advice applying to Device Manager don't get me anywhere, because my Kindle doesn't show up.
Any other ideas?
kyleboyd said:
Thanks for the reply!
I tried that. When I type "fastboot getvar product" it says waiting for device or something similiar.
The advice applying to Device Manager don't get me anywhere, because my Kindle doesn't show up.
Any other ideas?
Click to expand...
Click to collapse
When using the stock bootloader (plain "kindle fire" boot logo), the fastboot command must always specify the custom vendor ID used by the Kindle Fire. For example, the commands above must be slightly altered to...
Code:
fastboot -i 0x1949 getvar product
fastboot -i 0x1949 devices
and likewise, all of the following commands will need the "-i 0x1949" switch when using the stock bootloader. The FFF bootloader's vendor ID has been changed to one that is normally recognized by fastboot, so the "-i 0x1949" switch can be omitted.
Now onto some more useful fastboot commands...
Code:
fastboot oem idme bootmode 4000
fastboot oem idme bootmode 4002
fastboot oem idme bootmode 5001
Using one of these commands will change the bootmode to normal (4000), fastboot (4002) or recovery (5001). Then issuing...
Code:
fastboot reboot
will reboot the device into the respective bootmode.
I've tried that as well...
Just so I am totally clear, this is what I did in relation to those instructions:
Opened Command Prompt - set the directory to C:/kfu/tools
Typed "fastboot -i 0x1949 getvar product" (with out the quotations, obviously)
<waiting for devices>
I plugged Kindle in, it powers on and the frozen logo pops up.
I also tried "fastboot -i 0x1949 oem idme bootmode 4000" and "fastboot -i 0x1949 oem idme bootmode 4002"
According to the guide it often takes multiple tries, I have done it over and over again.
I have also tried different orders of code, plugging in Kindle, and powering on and off.
Am I doing something wrong? Is there a specific code for my Kindle? (Not -i 0x1949)
Thanks!
Have you tried this?
http://forum.xda-developers.com/showthread.php?t=1660636
Reinstall the driver then use kfu to reset the boot mode to normal.
Drivers?
I did try this: http://forum.xda-developers.com/show....php?t=1660636
When I get to the part about the Device Manager, I am stuck, as nothing shows up (I suspect something do with drivers)
Thepooch said:
Reinstall the driver then use kfu to reset the boot mode to normal.
Click to expand...
Click to collapse
By reinstall drivers do you mean clicking on "install_drivers" in the KFU folder? I have tried that.
Is there another method of uninstalling and installing drivers? Sorry if that is a dumb question!
If the devices is in fastboot which I believe it is it would show up as android adb interface, if it was attempting to boot to the system it would show up as android composite adb interface. If you are on xp or windows 8 this can be a bit of a tricky task. Android adb interface and android composite interface are two facets of the same driver. So yes I suggest rerunning the driver installation bat that is packaged with KFU. If perhaps you are on windows 8 you must disable driver signature verification and reinstall the driver. 3.0 usb ports have an issue with fastboot and can leave the device undetected.
Still not working
Thepooch said:
If the devices is in fastboot which I believe it is it would show up as android adb interface, if it was attempting to boot to the system it would show up as android composite adb interface. If you are on xp or windows 8 this can be a bit of a tricky task. Android adb interface and android composite interface are two facets of the same driver. So yes I suggest rerunning the driver installation bat that is packaged with KFU. If perhaps you are on windows 8 you must disable driver signature verification and reinstall the driver. 3.0 usb ports have an issue with fastboot and can leave the device undetected.
Click to expand...
Click to collapse
Thanks for the quick reply.
So I am on a Win7 and/or a Windows XP. Currently on both systems, when I plug it into the computer, with the Device Manager open, nothing happens other than the Kindle turning itself on.
Before it froze up, I saw it in device manager as Android ADB interface, and before doing anything at all, saw it as the default Kindle Fire.
On the Win7 system, I have rerun the driver installation bat over and over and over again, with absolutely no results.
On the WinXP, I have tried it, and for the life of me can't get it to install (it says install failed (Unsigned)). I never connected the Kindle up to this computer before it froze up, so I wonder if that is somehow causing the problem (it is trying to update drivers that don't exist?)
Am I doing something wrong with this? Can I uninstall or delete drivers, and totally start over?
If you are using a WinXP you must install driver manually.
Drivers?
zastava750 said:
If you are using a WinXP you must install driver manually.
Click to expand...
Click to collapse
How do I do that, when the Kindle does not show up as being connected? All the guides I have found start off with accessing from the Device Manager. My Kindle does not show up in the Device Manager...
okay well then you`re running xp use another computer getting the driver installed is hard even for the very skilled particularlly when the device is stuck in fastboot. Friend or relatives computer running windows 7 would be perfect. Otherwise it`s linux on a live usb booted on your xp machine.
Windows 7 - No Dice
Thepooch said:
okay well then you`re running xp use another computer getting the driver installed is hard even for the very skilled particularlly when the device is stuck in fastboot. Friend or relatives computer running windows 7 would be perfect. Otherwise it`s linux on a live usb booted on your xp machine.
Click to expand...
Click to collapse
Yeah so I have a Windows7. I have reinstalled the drivers (by clicking on the install_drivers.bat file in the KFU) over and over again, and I still do not get any recognition on the computer, or in the Device Manager when I plug in the Kindle.
Try different usb port, make sure they are usb 2.0. Is the logo static or animated? It possible that you broke the bootloader. At some point I would be willing to look at some things for you via teamviewer. If it is not driver related I fear your next move is here http://forum.xda-developers.com/showthread.php?t=1430038. Keep it on charger or off till it can be dealt with.
Thepooch said:
Try different usb port, make sure they are usb 2.0. Is the logo static or animated? It possible that you broke the bootloader. At some point I would be willing to look at some things for you via teamviewer. If it is not driver related I fear your next move is here http://forum.xda-developers.com/showthread.php?t=1430038. Keep it on charger or off till it can be dealt with.
Click to expand...
Click to collapse
Thanks! I would be willing to give it a shot (teamview I mean) if you are willing.
I tried the Firekit before I began this thread, but I kept getting stuck trying to run the tool after booting into ubuntu. Perhaps that is a different thread topic, but I am more than willing to put more work into figuring that out, if it could be the key to unlocking this stupid thing.
I am having this exact same problem. Using Win XP i was able to get the ADB drivers loaded initially and used KFU to try to install TWRP. When it rebooted during that process it got stuck at the Kindle Fire logo. Since then I cannot get my computer to recognize the kindle. Like you, I feel like i've tried everything.
Nixnaegie said:
I am having this exact same problem. Using Win XP i was able to get the ADB drivers loaded initially and used KFU to try to install TWRP. When it rebooted during that process it got stuck at the Kindle Fire logo. Since then I cannot get my computer to recognize the kindle. Like you, I feel like i've tried everything.
Click to expand...
Click to collapse
Glad to know I'm not alone - misery loves company! Solidarity my friend.
I wish I could tell you I'd solved it, but alas, I have not. I'm still working on it, I'll keep you updated if I have any breakthroughs!