Develop Bugs

Not able to Mount EXT4

Anyone experienced that, the system is not able to mount the E: (SD-EXT) after flashed the ROM. Here is what I was doing.
1) I use PartedMagic to setup the following
6.4GFAT32+1.5G EXT4+ 0.4G EXT4+ 0.2 SWAP (appox size.)
2) in the recovery loader, I tested I can mount the SD-EXT without any problems and that I flashed the ROM.
3) After the process done, I started the new MOD and let the system run by itself for the 1st 10mins for him to settle down.
4) I try to reload the data and apps, and seem the system become unstable..so I reboot (my 1st reboot)
5) load the recovery loader, and the SD-EXT is not about to mount again....
Can anyone help please ??
However, I have try to format FAT32+EXT4... Still the EXT4 is not able to mount..
Thx

Redo your partitions with gparted and the card in a card reader. If you don't have a card reader make sure the phone is in recovery while partitioning.
Sent from my HTC Desire using XDA App

I am using PartedMagic to done all the palpitation.. Seem still have problem... now.. I got no choose and test the D2EW with FAT + EXT3 instead. (RCMIxHD_v3.0_D2WE.)
http://forum.xda-developers.com/showthread.php?t=789830

Any feed back pls ..... ?

can you get the phone to plug into your pc as this happened to me once and I had USB bricked the phone.

langers1 said:
can you get the phone to plug into your pc as this happened to me once and I had USB bricked the phone.
Click to expand...
Click to collapse
yes.. my windows can access my SD (readable to the FAT32 part)...
I am now using
RCMixHD v3.0, 1.84.661.1 /D2WE/
FAT+EXT3..
so far so good but abit laggy... and I hope I can go for 2DEXT
...
hope someone can help..

Please ask the rom developer if his kernel supports ext4, this is not available by default !

Make sure to erase the cells before formatting in Ext, and then, run melethron's alignment script. It helps much.
------------------------------
- Sent via HTC Desire -

th3 said:
Make sure to erase the cells before formatting in Ext, and then, run melethron's alignment script. It helps much.
------------------------------
- Sent via HTC Desire -
Click to expand...
Click to collapse
Can you tell me more detail please ?

Which D2E ROM/version are you trying to install after the partitioning?
------------------------------
- Sent via HTC Desire -

I try to install RCMIxHD_v3.0 and i am using D2WE fat+ext3 at the moment .
Sent from my HTC Desire using XDA App

can anyone help please ?

- I doubt RCMixHD stock kernel allows mounting/formatting Ext4 (through Recovery). I've never had success.
- D2W is mainly for space. It lags and delays quite heavily if you have a SD card below Class 6 (or if the partition is near full, many cells dirty or many pages partially full). I think Melethron's Ext alignment script runs automatically with the v3.0 version of that ROM when you install it. I haven't had the free time to check his latest script, just got out from having a 2h operation.
------------------------------
- Sent via HTC Desire -

I am uisng Class 6 SD card.. still lag.. and I am back to unroot orignal ROM..... BTW.. do you have any idea... Is that orignal worldclockmod is not support EXT4 ??? and what ROM you suggest me to use ?? My Phone is S-ON .... and I still got no idea how to make it S-OFF
thx
SK
th3 said:
- I doubt RCMixHD stock kernel allows mounting/formatting Ext4 (through Recovery). I've never had success.
- D2W is mainly for space. It lags and delays quite heavily if you have a SD card below Class 6 (or if the partition is near full, many cells dirty or many pages partially full). I think Melethron's Ext alignment script runs automatically with the v3.0 version of that ROM when you install it. I haven't had the free time to check his latest script, just got out from having a 2h operation.
------------------------------
- Sent via HTC Desire -
Click to expand...
Click to collapse

Runnymede AIO V4.0.1

So i want to try Runnymede AIO V4.0.1, but under installation i get
"Your device NOT support AD2SDX"
Tried to search abit for it. and found out i needed atleast 1024mb EXT for it to work, or max 1,5GB EXT4,(i have 16Gb memory card) so i used Partition Wizard and and did 12,5GB Fat32 Primary and 1,5Gb EXT4 primary and 1 GB swap Linux.
Still it says "Your device NOT support AD2SDX"..
Im not good at all in this, so please have patient with me!
Thanks in advanced!
VikingNor

VikingNor said:
So i want to try Runnymede AIO V4.0.1, but under installation i get
"Your device NOT support AD2SDX"
Tried to search abit for it. and found out i needed atleast 1024mb EXT for it to work, or max 1,5GB EXT4,(i have 16Gb memory card) so i used Partition Wizard and and did 12,5GB Fat32 Primary and 1,5Gb EXT4 primary and 1 GB swap Linux.
Still it says "Your device NOT support AD2SDX"..
Im not good at all in this, so please have patient with me!
Thanks in advanced!
VikingNor
Click to expand...
Click to collapse
you need to install the a2sd option,ad2sdx is only supported for cm7/r2 hboot,also you do not have a swap on this rom

Where do i find this a2sd option, and do i start it in recovery mode? and another question,
cm7/r2 hboot what is the different? and i see there is 1 IMG file and 1 .Zip file.

VikingNor said:
Where do i find this a2sd option, and do i start it in recovery mode? and another question,
cm7/r2 hboot what is the different? and i see there is 1 IMG file and 1 .Zip file.
Click to expand...
Click to collapse
Dont use a windows program to partition a sd card for android. Use Gparted or 4ext recovery. You dont need a swap partition. If you still on stock when installing the RoM select custom install and then select app2sd option. If you have CM7/r2 Hboot you can then use the xd2sdx.
CM7/r2 is a Nand partition that makes the data part bigger then stock, on stock after fresh install of a RoM you left with 150MB for apps on CM7/r2 its 287mb.
On xd2sdx version all system files stay on this Nand data and your ext4 becomes the storage data so when you look at phone storage you will see what ever your ext4 size is 1.5GB free

VikingNor said:
Where do i find this a2sd option, and do i start it in recovery mode? and another question,
cm7/r2 hboot what is the different? and i see there is 1 IMG file and 1 .Zip file.
Click to expand...
Click to collapse
Sorry to say, but why don't you use the search function before asking? You can read a lot in the ROM's thread.
Sent from my HTC Desire using xda premium

VikingNor said:
Where do i find this a2sd option, and do i start it in recovery mode? and another question,
cm7/r2 hboot what is the different? and i see there is 1 IMG file and 1 .Zip file.
Click to expand...
Click to collapse
While installing, don't tick "Typical" (or "Default", can't remember right now), but "Custom".
Greets, Magpie

Hi!
i have installed Runnymede AIO V4.0.1 and i have some problems. for some reasons my phone sometimes get stuck.. its looks like showing photo, nothings move, and don't react for any button or touch. only restart help.
how can i fix it?
also.. where i can read about bugs on camera 3.0.. i cant find it.. :/

matebosh said:
i have installed Runnymede AIO V4.0.1 and i have some problems. for some reasons my phone sometimes get stuck.
Click to expand...
Click to collapse
Most of the times this is a matter of incompatible or too slow SD-Card. Are you using A2SD or AD2SDX? And what kind of SD-Card? Make and Class are important.
where i can read about bugs on camera 3.0.. i cant find it.. :/
Click to expand...
Click to collapse
In the RunnyMede thread. It's just about the Previews.
Greets, Magpie

in mot sure about a2ds or a2dsx.. i have 16gb scandisc 4 class SD..
this problem shows always when i turn on operator internet, 3g and when i want to play music from mp3 without 3g.. in airplane mode or with wifi with working sim everything is ok.
[edit]
when i want to instal rom it says "Your device NOT support AD2SDX" albo it says i use cm7/r2 hboot ... whats wrong? i used recovery to make ext partition over 2gb space

matebosh said:
in mot sure about a2ds or a2dsx.. i have 16gb scandisc 4 class SD..
this problem shows always when i turn on operator internet, 3g and when i want to play music from mp3 without 3g.. in airplane mode or with wifi with working sim everything is ok.
[edit]
when i want to instal rom it says "Your device NOT support AD2SDX" albo it says i use cm7/r2 hboot ... whats wrong? i used recovery to make ext partition over 2gb space
Click to expand...
Click to collapse
Ext partition cannot be more than 2GB. Less than that is better, say 1.5GB.
Sent from my HTC Desire using xda premium

ok. it helps. i didnt know i cant set over 2gb ext. ad2sdx is suported now... now i will check when my phone will stuck..
[edit]
still getting stuck.. when i turn on 3G after few seconds or when some errors show like "unexpected android market shut down".

Same Problem
Hey Guys,
I have a CM7 R2 Hboot and used the Runnymede AIO 3.0.5 with XD2SDX (and it works perfectly) before. But when I try to install the New ROM I can not choose the AD2SDX.
In addition, after Installation, the Desire is not starting, it hangs in Boot Animation for one hour.
Whats the problem?
And, what is more worse, I tried to recover my old Image and It's not working..
So now I have a problem.. Anyone can help me?
Bernd

bposi said:
Hey Guys,
I have a CM7 R2 Hboot and used the Runnymede AIO 3.0.5 with XD2SDX (and it works perfectly) before. But when I try to install the New ROM I can not choose the AD2SDX.
In addition, after Installation, the Desire is not starting, it hangs in Boot Animation for one hour.
Whats the problem?
And, what is more worse, I tried to recover my old Image and It's not working..
So now I have a problem.. Anyone can help me?
Bernd
Click to expand...
Click to collapse
The new installer detects your Hboot automaticly. Some people have problem there. This issue will be solved shortly.
The use your backup you need a full wipe before restoring. It should definitely work.
Good luck.
Sent from my HTC Desire using xda premium

Coempi said:
The new installer detects your Hboot automaticly. Some people have problem there.
Click to expand...
Click to collapse
Should be solved with 4.0.3
Greets, Magpie

[Q] Query on Internal Memory and Custom Image

Hey Guys
My friend has a Wildfire S.. We have S-offed it.. and put custom recovery.. CWM 5.0.2.8 .. Questions are
1) Is that good or latest recovery? or something better?? like TWRP ?
2) We have drilled down to three ROM's we can see..
CM10.1 4.2.1
CM10 4.1.2
CM7 2.3.7
We had tried CM10.1 but felt a bit sluggish.. slowish.. probably needed to do something more...
which rom is good out of the three or any other??
(we don't care about the usb tethering not working or camcorder recording etc).. should not be sluggish although.. won't say it will be lightning fast either.. I know the phone is quite old and limited..
3) We saw internal memory used 100MB and left only 20MB.. obviously we need to increase that.. we have a 12GB Card.. Now..
Do we need to format to ext4 ? full Card or partition? how much? what with the rest of the partition ?
Then which one to use for data to SD by default? Do we use INT2EXT4+ as mentioned in CM10.1 guide?
Is that compatible with all the ROM's or others above
We can currently format so just want to set it up correctly first time.. dont want to get it wrong..
any answers will be great!!
Cheers

Actually you posted in wrong section.. This should goes to Q/A section.... and yeah these questions have asked many times... Try search before posting...
Anyway... there is a touch type CWM recovery available(search in development section)... but 5.0.2.8 is used by most of the users, cuz no one need more than that....
Try cm9 roms... like MIUI, Paranoid Android ICS, Speed Droid... Those are great and quite stable and of course fast...
and for SD Card tweaks.. ext2 and ext4 are best... But for cm9, cm10 ext4 partition is preferred (idk why)...
make a second partition using minitool as ext4 and make it as primary (imp - not as logical)... then flash the int2ext+ (or) int2ext4+ script after you flashed the rom...
note that int2ext4+ is only for ext4 type partition and int2ext+ is for all ext2,3,4 type partitions... You can partition you sd card upto 2 GB ... cuz it is stable limit..
Yes int2ext scripts works with all roms....

Thanks for that..
So CM10 rom is not going to be quick?? which is good in Gingerbread then?
So I should format the 12GB card into 1) primary ext4 of 2GB and 2) leave the rest as FAT32??
then
1) Wipe everything
2) Install custom ROM
3) Install int2ext+
4) reboot
5) get into recovery again
6) install gapps
7) reboot??
missing anything?? also do i need custom kernel etc?? which one if so??

Flash the JellyKing rom by kantry. It is a smooth and stable cm 10 rom. There is eoghan's kernel in that rom so you don't have to flash a kernel.
Everything else like you listed it in the last post.

4ndaKava said:
Flash the JellyKing rom by kantry. It is a smooth and stable cm 10 rom. There is eoghan's kernel in that rom so you don't have to flash a kernel.
Everything else like you listed it in the last post.
Click to expand...
Click to collapse
Thanks will try that ROM
so is that generally best atm.. and any recommendation on custom recovery??
so
1) wipe
2) format 2GB ext4 in sd card as primary and rest as fat32?? or any other?? both primary??
3) install ROM
4) install int2ext+
5) reboot
6) install gapps
will this work for any ROM ?

khandu said:
Thanks will try that ROM
so is that generally best atm.. and any recommendation on custom recovery??
so
1) wipe
2) format 2GB ext4 in sd card as primary and rest as fat32?? or any other?? both primary??
3) install ROM
4) install int2ext+
5) reboot
6) install gapps
will this work for any ROM ?
Click to expand...
Click to collapse
yeah.let me clear about partition of sdcard:
for int2ext scripts
1) FAT32
2) ext3 or ext4 (as per custom rom,some rom wont work with ext4 but cm9 and cm10 will do)
for link2sd
1)FAT32
2)ext3 or ext4
3)linux swap partition(as per your phone RAM,512 MB is enough)
int2ext scripts dont require swap partition as per their description in main post.all partition should be primary,and 1 GB is enough but if you want 2 GB its ur choice but dont partition more than 2 GB,and yeah int2ext+ script uses 100 MB internal memory for 500 MB ext3/ext4 so if you partition 2 GB,your 400 MB internal space will be consumed..
you can directly partition you sdcard with help of minipartition tool on your computer.
and for you clearance linux swap partition is work as your backup rom.some cache will save on that partition so your phone speed wont slow.

Thanks..
Considering (in terms of preference)
1) JellyKing
2) Paranoid Android
3) Speed Droid
Any suggestions between the three?
Also I am planning to use in2ext+ with the following
1) 1st Partition - Primary 1.5GB ext4 (Read maximum should be 2GB so just being safe?)
2) 2nd Partition - Primary 14.5GB FAT32
So
1) Do the partition structure and size look good ?
2) Do all these roms support int2ext+ (I think so on reading)..
3) Do I create a swap partition as well? if so which order and how much? (reading suggests 500MB).. whats the advantage? any additional thing to be used for install? how to check if it worked as it should?
So after doing that.. I should
1) Wipe everything
2) Install ROM
(reboot or not after that??)
3) install int2ext+
4) Reboot and see if rom detects internal memory properly?
5) back into recovery and install gapps and reboot
Does all of this sound good??
Need to do this in an hr or 2 so quick reply will be appreciated
Cheers

khandu said:
Thanks..
Considering (in terms of preference)
1) JellyKing
2) Paranoid Android
3) Speed Droid
Any suggestions between the three?
Also I am planning to use in2ext+ with the following
1) 1st Partition - Primary 1.5GB ext4 (Read maximum should be 2GB so just being safe?)
2) 2nd Partition - Primary 14.5GB FAT32
So
1) Do the partition structure and size look good ?
2) Do all these roms support int2ext+ (I think so on reading)..
3) Do I create a swap partition as well? if so which order and how much? (reading suggests 500MB).. whats the advantage? any additional thing to be used for install? how to check if it worked as it should?
So after doing that.. I should
1) Wipe everything
2) Install ROM
(reboot or not after that??)
3) install int2ext+
4) Reboot and see if rom detects internal memory properly?
5) back into recovery and install gapps and reboot
Does all of this sound good??
Need to do this in an hr or 2 so quick reply will be appreciated
Cheers
Click to expand...
Click to collapse
sorry for late reply but my internet sucks.
first install speedroid.its fast,stable.i m using it s.:cyclops:
another reasons are jellyking is based on JB,which has many little bugs despite camcorder and all.and paranoid has dockbar and dpi size is very small so i dont like it.but its upto you what you want.
and use int2ext4+
its very fast and better than int2ext+ and yeah all cm9 and cm10 roms supports it.
partitions are good,you can use 1.5 GB ext4 but keep it 1 GB for caution purposes.might you dont need 1.5 GB belive me.
and yeah swap partition isn't need in int2ext4+ scripts but you have 16 GB memory card so keep swap partition 512 MB.
swap is work as backup RAM,its 512 MB because wildfire s has 512 MB ram.
steps:
1)wipe everything
2)install rom
3)install int2ext4+
4)go to "mount and storage"
5)format /sd-ext (its needed to format your sd-ext partition)
6)reboot
its take little long time to boot because we installed int2ext4+ script.then you can check internal memory.
then reboot in recovery again and install gapps.
and yeah if you wanted to install speeddroid,gapps already installed in it so no need to flash it.

need quick help.. have done everything and shows internal memory fine and have put speed droid
but i am installing gapps-jb-20120726-lite-rebased.zip and reboot but not a single gapps showing in phone.. it flashes fine as well..
partition
1) fat32 12GB
2) ext4 - 2000MB
3) swap - 500MB
using int2ext4+

khandu said:
need quick help.. have done everything and shows internal memory fine and have put speed droid
but i am installing gapps-jb-20120726-lite-rebased.zip and reboot but not a single gapps showing in phone.. it flashes fine as well..
partition
1) fat32 12GB
2) ext4 - 2000MB
3) swap - 500MB
using int2ext4+
Click to expand...
Click to collapse
you installed JB version..i have ICS version so not sure about gapps.
but might you installed wrong gapps.
when you installed gapps and reboot,
on your screen something like that "android is upgrading?"
---------- Post added at 02:49 PM ---------- Previous post was at 02:45 PM ----------
crossfire77 said:
you installed JB version..i have ICS version so not sure about gapps.
but might you installed wrong gapps.
when you installed gapps and reboot,
on your screen something like that "android is upgrading?"
Click to expand...
Click to collapse
and its not because of int2ext4+.
its fine.
just might you flashed wrong gapps.
search latest gapps on goo.im website.
and flash it.
good luck.

crossfire77 said:
when you installed gapps and reboot,
on your screen something like that "android is upgrading?"
---------- Post added at 02:49 PM ---------- Previous post was at 02:45 PM ----------
and its not because of int2ext4+.
its fine.
just might you flashed wrong gapps.
search latest gapps on goo.im website.
and flash it.
good luck.
Click to expand...
Click to collapse
No.. I know it should show that android is upgrading. it does not
i am reformatting to ext3 and going to use int2ext+ and try again!!!
Downloading gapps-jb-20121011-signed.zip
didnt work .. shows upgrading android.. but no apps show from gapps

khandu said:
No.. I know it should show that android is upgrading. it does not
i am reformatting to ext3 and going to use int2ext+ and try again!!!
Downloading gapps-jb-20121011-signed.zip
didnt work .. shows upgrading android.. but no apps show from gapps
Click to expand...
Click to collapse
oh..but keep in mind..nothing wrong in ext4 partition.its good for cm9 and cm10 though..anyways u can do one thing might it ll help..
1)wipe everything
2)install rom
3)install gapps
and then install int2ext.

crossfire77 said:
oh..but keep in mind..nothing wrong in ext4 partition.its good for cm9 and cm10 though..anyways u can do one thing might it ll help..
1)wipe everything
2)install rom
3)install gapps
and then install int2ext.
Click to expand...
Click to collapse
Yes I did that this time.. but left ext3 as it is..didn't convert it back to ext4.. hope that does not screw anything up..
worked this time.. used the speed rom ics build!!!

[Q] Low on internal memory

Hi,
I'm having trouble installing a2sd and if i partition my sd card thrue recovery it dus not see the partioned part. so my internal storage keeps the same ( to small )
Mod version : CyanogenMod-7-20130301-NIGHTLY-bravo
Android version : 2.3.7
BRAVO PVT1 SHIP S-OFF
HBOOT-6.93.1002

I dont think cm has any a2sd script by default. You need to flash one such as m2sd or a2sd, or you could use the s2e app from the play store.

Chromium_ said:
I dont think cm has any a2sd script by default. You need to flash one such as m2sd or a2sd, or you could use the s2e app from the play store.
Click to expand...
Click to collapse
thank you again for replying so quickly on my posts ! realy apreciate it ! could you help me out some more by telling me if a2sd is a standard script for al the roms or should i download a specific a2sd for my CM 7 mod ? and if so where can i find a2sd ? do they have a site or somthing ?
thanks in advance !

anthony.bog said:
thank you again for replying so quickly on my posts ! realy apreciate it ! could you help me out some more by telling me if a2sd is a standard script for al the roms or should i download a specific a2sd for my CM 7 mod ? and if so where can i find a2sd ? do they have a site or somthing ?
thanks in advance !
Click to expand...
Click to collapse
Download this and flash this script from recovery:
https://dl.dropboxusercontent.com/u/48303918/apps_dalvik2ext-UNSIGNED.zip
It moves data/app and dalvik cache to sd-ext.

abaaaabbbb63 said:
Download this and flash this script from recovery:
https://dl.dropboxusercontent.com/u/48303918/apps_dalvik2ext-UNSIGNED.zip
It moves data/app and dalvik cache to sd-ext.
Click to expand...
Click to collapse
thanks for the respond! I downloaded the file and i flashed it. i dont realy know what it did so i took a look at your tutorial ---> http://forum.xda-developers.com/showthread.php?p=37383522 and did what you explained there for partitioning my sd card evrything went well but now my desire wont boot anymore its stuck on the htc loading screeni can still enter the hboot and recovery tho

anthony.bog said:
thanks for the respond! I downloaded the file and i flashed it. i dont realy know what it did so i took a look at your tutorial ---> http://forum.xda-developers.com/showthread.php?p=37383522 and did what you explained there for partitioning my sd card evrything went well but now my desire wont boot anymore its stuck on the htc loading screeni can still enter the hboot and recovery tho
Click to expand...
Click to collapse
Heres a quick way to make your phone good:
Ok now this is what i would advise: Install the Oxygenr2 hboot, full wipe, install milwild redux rom. This will give you 332mb for app data, and the apps (apks) and dalvik cache will be stored on your sdext partiton.
1. Download the oxygenr2 hboot here. Rename the file to PB99IMG.zip and then follow this guide to install it. When you go into your bootloader it should now say 'Alpharev Oxygen r2' at the top...this means that it was installed successfully.
2. Download Milwild Redux rom from here and put it on your sdcard.
3. Go into 4ext recovery > wipe | format > format all partitions (except sdcard) *This will wipe everything on your phone except your sdcard stuff like pics, music, video, etc.*
Go back to the 4ext main menu > install from sdcard > choose zip from sdcard > browse to where you copied the rom, and click on it to install
4. Reboot. You should now have milwilds redux rom installed, and apps will automatically be moved to your sdcard partition. App data will remain on the internal so you will eventually run out of space, but it should take much longer than it used to.

Chromium_ said:
Heres a quick way to make your phone good:
Ok now this is what i would advise: Install the Oxygenr2 hboot, full wipe, install milwild redux rom. This will give you 332mb for app data, and the apps (apks) and dalvik cache will be stored on your sdext partiton.
1. Download the oxygenr2 hboot here. Rename the file to PB99IMG.zip and then follow this guide to install it. When you go into your bootloader it should now say 'Alpharev Oxygen r2' at the top...this means that it was installed successfully.
2. Download Milwild Redux rom from here and put it on your sdcard.
3. Go into 4ext recovery > wipe | format > format all partitions (except sdcard) *This will wipe everything on your phone except your sdcard stuff like pics, music, video, etc.*
Go back to the 4ext main menu > install from sdcard > choose zip from sdcard > browse to where you copied the rom, and click on it to install
4. Reboot. You should now have milwilds redux rom installed, and apps will automatically be moved to your sdcard partition. App data will remain on the internal so you will eventually run out of space, but it should take much longer than it used to.
Click to expand...
Click to collapse
thank you again... i keep on saying it ! i realy dont care what rom i'm running actualy as long its stable and fast ! and i can download as many apps as i like becaus thats the reason i bought an 32 gig sd card so thanks again for the reply ! i will try this whene i got the time now i need to study my ass off but thanks i will keep you posted how it went ! thanks ! ! !

anthony.bog said:
thank you again... i keep on saying it ! i realy dont care what rom i'm running actualy as long its stable and fast ! and i can download as many apps as i like becaus thats the reason i bought an 32 gig sd card so thanks again for the reply ! i will try this whene i got the time now i need to study my ass off but thanks i will keep you posted how it went ! thanks ! ! !
Click to expand...
Click to collapse
No problem. The rom i linked you to is definitely just as stable & fast as official cm7, if not more.
That combination (milwild redux + oxygen r2 hboot + 1gb ext4 ext partition) is great for stability and lots of room for apps.

hmmmm i did al the installations but its still stuck on the loading screen of htc it wont start the milwild redux rom kinda strange... can you help me out ?

Chromium_ said:
No problem. The rom i linked you to is definitely just as stable & fast as official cm7, if not more.
That combination (milwild redux + oxygen r2 hboot + 1gb ext4 ext partition) is great for stability and lots of room for apps.
Click to expand...
Click to collapse
Hey thanks ^^ its running smooth now ^^ but i have one more qeustion if i install apps they take place on the internal storage again... is there anny way around this so they get installed on my sd card its becaus the facebook app, skype and what not take so much place thanks in advance and for the previous help !

Originally Posted by Chromium_<br />
No problem. The rom i linked you to is definitely just as stable & fast as official cm7, if not more. <br />
That combination (milwild redux + oxygen r2 hboot + 1gb ext4 ext partition) is great for stability and lots of room for apps.
Click to expand...
Click to collapse
<br />
<br />
Hey thanks ^^ its running smooth now ^^ but i have one more qeustion if i install apps they take place on the internal storage again... is there anny way around this so they get installed on my sd card its becaus the facebook app, skype and what not take so much place thanks in advance and for the previous help !
Click to expand...
Click to collapse
Read #4 of my instructions above.
Sent using xda-developers app

Chromium_ said:
Read #4 of my instructions above.
Sent using xda-developers app
Click to expand...
Click to collapse
Ok, I followed the stepts for fortmatting my sd card and partitioning 1 gig of the 32 gig's i have in 4ext becaus this is the fastest option i heard/readed. But whene i try to boot my phone after ive done this i get the htc loading screen over and over again the only way i get to boot my phone normaly is whene i take the sd card out... and if i format the sd card and put it back in my phone it boots normaly. Anny hints on what the problem could be ? thanks for helping me this far !

[Q] Beanstalk Rom low memory message

I am using Beanstalk rom Release 2, on my HTC Desire Bravo, The rom works perfectly fine, but I am facing some issues ,The internal memory fills up and there is no space for new apps to be install and Insufficient memory error message appears when i tried to install other apps, I do both the options as described in the thread ::
"" Install Mounts2SD - Manual method:
- Install Mounts2SD app through the play store
- Open Mounts2SD > Menu > Application Settings > Install Startup Script
- Click the wrench icon in Mounts2SD. Under the Content header, enable Applications and Dalvik Cache.
*Dont be confused by that fact that they seem to already seem to be checked. They are not. You must click on them so that the checkmark become green*
*Grey checkmark = disabled. Green checkmark = enabled*
- Reboot (might take a while)
OR
Install Mounts2SD - Easy method:
- Flash this zip (h_t_t_p://www.mediafire.com/download/3y4n4bbd9ga93zu/M2SD_Apps%2BDalvik.zip)
- Reboot (might take a while)
But i still got low memory error and my second problem is when i tried to reply sms from status bar with quick reply option rom crashes and the phone reboots.
I want to post that on that thread as a reply but unfortunately it said that "You don't have the rights to do so"
The Rom thread is: h_t_t_p://forum.xda-developers.com/showthread.php?t=2651790 (Remove the underscores from http, as i don't have the rights to post a link too )
Plz help !!
Regards,
BRAVO PVT4 SHIP S-OFF
HBOOT-6.93.1002
MICROP-051d
TOUCH PANEL-SYNW0101
RADIO-5.11.05.27
Aug 10 2010

Did you partition your sd card as per the instructions in the first post?
You will also gain a little more space by flashing the 250/5/182 hboot in the same post (search for a guide how to flash them, I recommend via fastboot)

Is this actually related to the process of partitioning ?
---------- Post added at 08:56 PM ---------- Previous post was at 08:42 PM ----------
I have a desire s-off.. I installed the beanstalk R2 just a while back.. Installation went smooth..everything works fine with all already noted problems..
the real problem is coming with mounts2sd installation.. tried the app from playstore.. it did not install the script saying the deice is s-on.. My desire bootloader still shows s-off and am on 4ext which requires s-off.. i tried flashing the zip which also failed.
i then tried the older version of mounts2sd.. still the same error..
finally i tried links2sd in desperation which also refused installation of the script..
what seems to be the problem here ? I cant move forward without a2sd support.

It has everything to do with partitioning.
Mount2sd or any a2sd method requires a correctly partitioned sdcard.
So guess I may as well ask you too...did you partition your sdcard as per the instructions in the first post?

I partitioned the sd card a long time back through PC method.. It worked all well with all the roms which provide a2sd script inbuilt.. never faced any problem.
If at all the partitioning wasnt correct then how did the script work all those times?

SOLVED
The problem was insufficient space on system partition so the script wont get installed..I am using a custom 225 hboot.. The mounts2sd app kept giving error about s-on which misdirected the whole issue.

A short but immensely interesting and informative thread
Lessons learned
1. There are no issues with formatting cards under windows provided the card is good and the format settings are correct. (check the settings not the tool)
2. Utilities are just as crap at understanding what went wrong as we are
3. We as often get to the right answer for the wrong reasons, as the wrong answer for the right reasons
Thank You chaps. Entertaining and enlightening.

eddiehk6 said:
It has everything to do with partitioning.
Mount2sd or any a2sd method requires a correctly partitioned sdcard.
So guess I may as well ask you too...did you partition your sdcard as per the instructions in the first post?
Click to expand...
Click to collapse
I partitioned memory card as directed by using 4ext recovery , and i always did the same with a2sd script roms , and they worked perfectly fine.
First Mounts2sd says your device is S on, then i again run and then it goes all well, But after installing some apps insufficient space message appears, what to do ????

Mastermindsaifee said:
I partitioned memory card as directed by using 4ext recovery , and i always did the same with a2sd script roms , and they worked perfectly fine.
First Mounts2sd says your device is S on, then i again run and then it goes all well, But after installing some apps insufficient space message appears, what to do ????
Click to expand...
Click to collapse
Did you actually configure m2sd to move anything via the app, as instructed in the op of the ROM?
Sent from my HTC Desire using xda app-developers app

Chromium_ said:
Did you actually configure m2sd to move anything via the app, as instructed in the op of the ROM?
Sent from my HTC Desire using xda app-developers app
Click to expand...
Click to collapse
Yup i did all the steps , but i think that i downloaded RC1 before, yesterday i flashed RC2., and it works fine still , and hope so it continues
Many thanks