Related
Hi all
my elfin fell from quite a high place, and the four casings into which the small screws visible when you take off the back cover are broken...meaning the front casing is loose too.
do you know where I can find a front cover (I don't really need the back but I'm okay with buying both)... but before that I was thinking maybe someone could have bricked their elf or had an unusable device but with a front cover that's ok...
thanks in advance for your help !
Plenty of covers in a selection of colors on eBay, I suggest you try to find one there. Not that expensive and you can buy a digitizer to match the color.
hi
thnx for your answer . what's a digitizer?
ptitrusse said:
hi
thnx for your answer . what's a digitizer?
Click to expand...
Click to collapse
Digitizer is the outer screen cover attached to the faceplate that is responsible for touch function, the one you use your finger or stylus on. It's sold separately and is fairly easy to replace in cases when the touch function is lost or the digitizer is broken. You can get one to match the color of the housing for a complete look. Just look on eBay and you'll see what I mean.
oh... does that mean that the part responsible for touch function is actually stuck to the front casing and not to the screen itself? I hadn't thought about that... meaning I cannot jut change the front cover, I would have to replace this as well...
[edit] is it possible to use the one from my phone? cause it's working fine after all... I'm looking at it and I don't really know how to take it off...
ptitrusse said:
oh... does that mean that the part responsible for touch function is actually stuck to the front casing and not to the screen itself? I hadn't thought about that... meaning I cannot jut change the front cover, I would have to replace this as well...
[edit] is it possible to use the one from my phone? cause it's working fine after all... I'm looking at it and I don't really know how to take it off...
Click to expand...
Click to collapse
The digitizer is attached to the housing and in your case needs to be pried off before being used again and re-attached to the new housing. The digitizers are fairly cheap (the reason I don't bother with screen protector), so you will get unscratched and new one that you will have to attach to the new housing. My recommendation would be to buy a new housing and a matching digitizer.
Hi
thnx again for your help. I have one more question. Is the digitizer stuck to the screen or is it the actual hard plastic screen?
I find it's actually fairly expensive. When you add up the housing + the digitizer + the shipping costs it adds up to quite a lot..
[edit] Ok I think I finally got it now.
what do you think of this product ?
HERE
I'm trying to find a source on whether I can replace the trim know my phone since it's been dinged from the previous owner as well as myself.
I've found some the link to the replacement screen thread but it doesn't say if the lcd is part of the top or how to get it out? I've seen some oem housings online but not sure if I can remove my lcd which is fine and put it in the newer housing?
Is there glue or adhesive that holds it in?
Thanks for any help.
Sent from my GT-I9100 using xda app-developers app
You just need to unscrew the backplate and exchange it.
No glue no adhesives or something. it just sits there.
It will take about 10 minutes or so..
Here is a picture of the part:
Mine fell out of its place, the last i had the phone opened and i´m to lazy to put it back.
Edit: sorry for that huuuuge picture.. blame our 8mp camera.
supermult said:
You just need to unscrew the backplate and exchange it.
No glue no adhesives or something. it just sits there.
It will take about 10 minutes or so..
Here is a picture of the part:
Mine fell out of its place, the last i had the phone opened and i´m to lazy to put it back.
Edit: sorry for that huuuuge picture.. blame our 8mp camera.
Click to expand...
Click to collapse
Sorry - but I think we have a misunderstanding. I'm talking about the chrome trim around the entire LCD not the camera.
oh.. honestly i don´t think that the part you described is chrome. Atleast not on my GSII
and the thing i posted is the shiny ring around the headphone plug.
OP its not chrome its plastic..
1) replace the whole screen housing with with working parts from say ebay
2) buy a whole SGS2 housing unit and plus top screen ( this option you'll need to remove youe current lcd screen and once replaced in new housing the top screen needs to be bonded to housing. (M3 double sided tape or a thin silcon glue)
3) take it to a service centre
4)keep it as it is..
as par your question
Is there glue or adhesive that holds it in? Yes.
Top screen will need to be heated with hot air to release it from its bond.
Nyssa1104 said:
OP its not chrome its plastic..
1) replace the whole screen housing with with working parts from say ebay
2) buy a whole SGS2 housing unit and plus top screen ( this option you'll need to remove youe current lcd screen and once replaced in new housing the top screen needs to be bonded to housing. (M3 double sided tape or a thin silcon glue)
3) take it to a service centre
4)keep it as it is..
as par your question
Is there glue or adhesive that holds it in? Yes.
Top screen will need to be heated with hot air to release it from its bond.
Click to expand...
Click to collapse
Thanks - that's what I wanted to hear. So it's more effort than I'd like to spend on it. Looks like I'll just move the phone to try something else.
Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?
I have the HTC ONE X White AT&T, but I'm stuck on on replacing the screen, every video I can find on the internet is for he black version, and I need help with one part. After the motherboard etc was out, I have to remove the screen, I did, but idk if I got the lcd part too, because it is much thinner than the replacement. there is like 3 layers of paper/plastic s and then a gray screen left. Can anyone help? I can send pic I really really need help I don't want to mess this phone up!
Update
I split the LCD in half it looks like, but the digitizer seems to not be working correctly is there a way to repair it? or do I have to buy a new one?
show some picture. DId you buy lcd+digitizer or only lcd?
it was the combo the digitzer cable (the connector) seems to be bad as it is very difficult to connect compared to the one that came with my phone, when it does connect the touch is very very slow and uncalibrated. Pictures are coming
http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#0 http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#1 http://imgur.com/LEzw2aN,pzEvG88,BnrSmTl#2 here are some pics
IS there a way I can repair this?
I think you have a one xl (snapdragon) and not an international (tegra) version in which case it would explain why it doesn't fit or work properly.
If you do have the xl codename evita then you are also in the wrong forum my friend and should head over to the HTC one xl forum.
intel007 said:
I think you have a one xl (snapdragon) and not an international (tegra) version in which case it would explain why it doesn't fit or work properly.
If you do have the xl codename evita then you are also in the wrong forum my friend and should head over to the HTC one xl forum.
Click to expand...
Click to collapse
it says here that it works for both versions though http://www.amazon.com/Display-Digit...qid=1413140433&sr=8-2&keywords=HTC+One+X+AT&T. Every other product had low reviews, is there anywhere I can get a reliable screen replacement?
Pretty much every screen replacement says it doubles up with the HTC One XL. If anyone can help it is greatly appreciated.
can I use the old cable? somehow
Look here mate: http://www.etradesupply.com/htc/android-models/htc-one-x.html
I recently got a HTC screen here and it's perfect & original
Eric4753 said:
can I use the old cable? somehow
Click to expand...
Click to collapse
Hi,
The LCD on the One X and the XL can be different, there is a Sony and a Sharp version which aren't interchangable, but the Digitizer should be essentially the same, as the connectors are identical.
That said, I have come across a dodgy digitizer that was brand new before, and it occasionally does happen. If you want to tell the difference between the sharp and sony version of the LCD, the sharp version gas a green backing to the LCD flex cable while the sony has an orange/yelloy backing to the flex cable, check the attachment i've posted, the one on the left is sony, the one on the right is sharp. It is possible that you have a bad digitizer, but i take it that the LCD works. If thats the case check the connector pins on the main board to make sure they are not damaged (do the same for the digitizer) if it looks ok, and the digitizer is still playing up, i'd try and get a replacement.
Hope this helps
Well I got the thing back together, but I have problems mainly that I'm getting no signal, lastly what thickness of tape should I get?
You may need to open it up again and check everything is connected properly and that it's seated correctly in its rear shell, as there are contacts on the mainboard that touch the antenna mounted inside the shell, hopefully the phone is recognizing the sim and network.
I'm not sure what you want the tape for, could you explain?
We used carpenter's tape, because the tape we supposed to be supplied with didn't come in and the customer is in a rush, I was just asking what should be the thickness of the tape etc
Sorry, I wanted to know what you were going to use tape for, if it was to keep digitizer stuck to frame, I'd use the smallest amount of instant adhesive, being careful not to allow it to run under the glass, where you would see it when you press it down
We'll the screen is almost sticking out of the case despite this being the strongest tape I've ever run into, so I'll guess I'll need thinner tape I just don't want to take everything apart AGAIN and retape. It's a pain to do So should I remove the tape and use glue? Or get thinner tape?
If it's for the back of the LCD get the thinnest double sided tape you can, preferably something reputable like 3m as this is what's going to hold everything in place, if it's the digitizer, I'd use adhesive the tiniest drop in each corner and in the middle of each side, then press until it sets, you just have to be careful as if you use too much it can run from under the glass, and be visible.
---------- Post added at 04:11 PM ---------- Previous post was at 03:44 PM ----------
Just as a tip, you can get a replacement mid frame that already has the 3m tape on it, but I still like to put adhesive on the edges of frame where digitizer sits as sometimes the pressure of putting everything back in the shell can make it pop up.
Well upon taking it back apart the lcd, it got ripped like the bottom half of it is stuck to the tape the top half on the case and there are a bunch of white sheets etc in between them. now should I order a new one or can I repair this? its split in half, nothing is ripped. I'm about to just order a phone off amazon at this point.
You will have to get a new one, look at the videos on YouTube, there are plenty to help, but make sure you keep old one to change over as the phone needs to be turned on to do the LCD change. but if it's really damaged, you cash pick up a used one x reasonably cheaply, but the one m7 or m8 are great phones.
Well, after a couple of weeks with my shiny new ZE551ML (RAM 2GB) purchased overseas in a trip, today the big bastard fell and cracked the glass .
So a new screen (complete screen, even if touch and LCD still works but don't want to mess with heat gun) is on the way via Aliexpress, I've done some similar procedures on more complicated phones but can't find any official procedure or documentation for this one, maybe too new?
So anyone has a PDF or webpage with the procedure?
Best I could find is this, but many pictures are missing
http://www.ewisetech.com/Pages/Product/teardown.aspx?s=1961&dt=6820&img=65699
EDIT: See post #6
http://www.myfixguide.com/manual/asus-zenfone-2-teardown/
Bout the best one available at the moment. Looks fairly simple to do, especially if you are replacing the entire screen assembly, not just the glass.
Sammaul said:
http://www.myfixguide.com/manual/asus-zenfone-2-teardown/
Bout the best one available at the moment. Looks fairly simple to do, especially if you are replacing the entire screen assembly, not just the glass.
Click to expand...
Click to collapse
Thanks, at least it's better than the one I found. But no specifics instructions on replacing the screen (separating the last housing from the old panel. Glue? Heat Gun? Double tape?)
gipikay said:
Thanks, at least it's better than the one I found. But no specifics instructions on replacing the screen (separating the last housing from the old panel. Glue? Heat Gun? Double tape?)
Click to expand...
Click to collapse
I do not know unfortunately. I would think it is tape, as most tend to be tape, but I couldn't say for certainty.
If you would like to set up an Out-of-Warranty RMA for ASUS to repair please send me a private message at [email protected].
Or you may apply for an RMA online at http://www.asus.com/us/support/
Please ensure to mention the damage otherwise it will be rejected if received with no reported damage.
Sincerely,
Frank
ASUS_USA
Here's an album I've used to replace my screen, (pictures are from the first link I've posted before) there are a couple of things to consider that aren't one these pictures nor any on the internet and don't make the sames mistakes I did. If you have pictures, and working screens from a different seller, please post it and I'll add it to the thread .
http://imgur.com/a/Rmy02
The tools I've used are screwdriver, a metal spudger, double-tape for cellphone repair, and a heat gun. And of course, your replacement screen. In my case I've purchased for 30 dol. on Aliexpress, but did not come with adhesive or tape so you have to have your own.
To remove the first section (4th picture), not only do you need to remove the cover and black and silver screws, but be careful because the center "rails" (the plastic parts to the sides of where the double sim and sd-card are) of the section are fixed to the battery section with "light" double tape, nothing too strong and can be lifted with care.
In the 5th picture, lift the white part of the connector and very carfeully to remove the ribbon. I've made the mistake to be too forceful and cracked the black part a litlle bit.
WARNING! THIS STEP IS THE MOST DIFFICULT, MANY PEOPLE BREAK THEIR BATTERY WHEN REMOVING, SO BE CAREFUL. AGAIN, YOU'VE BEEN WARNED
Now, one of the most difficult parts of the teardown is between 5th and 6th picture. After removing the uppers ribbon you have to take the battery compartment, and let me tell you that the white double-tape that glues the battery to the frame is one of the strongest i've ever encountered. A metal spudger can be helpful and you can start with pressing the left side, but don't separate too much or go too deep cause you might damage the envelope of the battery (I scrapped and exposed a litlle bit of the cells, but for the moment the phone works and don't heat. Just in case, I already ordered a new battery) . So be extra careful on this step.
In the 7th picture, things looks a little different of what I've found, the upper board has a metal protection that's soldered so DON'T TAKE IT OUT! Remove the upper left small ribbon very carefully. The cables on the down board that connects to the vibration motor are very fragile so be careful.
At this point, you can remove the speaker (I didn't) and you have the upper section, so the real hard work starts to be able to replace your screen. I'm sorry but i didn't take many pictures of this procedure, but again a metal spudger was helpful to be able to separate the cracked screen from the frame.
Remove all pieces of glue, glass or residue that's still on the frame and put the first part of the double-tape on the frame but don't take the upper part just yet. Take the replacement part and check it fits on the frame, paying atention to the two ribbons, one in the middle and other in the upper side. In my case, when I did put the screen I started with the upper ribbon and then guided the middle ribbon to it's hole and then fit the screen to the frame.
Make all the steps in backward order to be able to re-assemble the phone. The final optional step I did, is to seal the double-tape in the screen with the heat gun and some weight (I used a 2.5 drive and a couple of 3.5)
So in the end, I managed to replace the screen with only a couple of small mistakes. When my new battery arrives, the steps will be similar (I removed the white strong double tape with a light adhesive one, so it will be more easy to remove and replace the battery).
All in all, it went pretty well
LIST OF SELLERS WITH WORKING PARTS, according to users
AliExpress - Shenzhen OMG Trade co.,LTD - Screen For ZE551ML - USD 22.39 - gipikay (OP)
Nice to see someone succeeded, I laughted at the big hard drive lol Those 3.5'' HDs are huge. 30$ for the 5.5'' 1080p screen is pretty good, there are for 20$ too.
I tried once replacing an iphone 4 lcd but the problem ended up to be the motherboard.
btw Does anyone know where is the Intel GSM modem located on the motherboard? I see nothing from those pictures about the modem. I could not find a reliable way of disabling it, tried scripts, deleting dial etc apks and /lib/ril files, cellphone still searches for signal with no sim inserted and airplane mode on.
Back when I ordered, this one was the cheapest and the only one for ZE551ML (now the same vendor lists the screen as USD 25).
If I could guess, the modem should be in the upper board, under the metal shielding (the stock pictures indicates two visibles intel chips under the enclosure, maybe a third in the right, and one down in the board)
Thanks, so will it need to be unsoldered for removal? I only use voip and cannot use gsm anyway.
Experienced basically the exact the same when i changed my display essambly. I broke the foil around the battery too, only problem is I can not find any vendor selling a replacement battery. Can you give me a hint where to buy it?
Thanks in advance!
Gesendet von meinem ASUS_Z00AD mit Tapatalk
gipikay said:
Back when I ordered, this one was the cheapest and the only one for ZE551ML (now the same vendor lists the screen as USD 25).
If I could guess, the modem should be in the upper board, under the metal shielding (the stock pictures indicates two visibles intel chips under the enclosure, maybe a third in the right, and one down in the board)
Click to expand...
Click to collapse
Did you replace the glass only, or the entire screen assembly?
gettohhole said:
Experienced basically the exact the same when i changed my display essambly. I broke the foil around the battery too, only problem is I can not find any vendor selling a replacement battery. Can you give me a hint where to buy it?
Thanks in advance!
Gesendet von meinem ASUS_Z00AD mit Tapatalk
Click to expand...
Click to collapse
This is the one I've ordered, even if it says for ZE550ML (mine is 551) the part number and battery is the same (I think the difference between models is the screen resolution)
EDIT: I leave the link, but this seller sent me the wrong battery, see post #21. Now I'm waiting for AsusParts to ship me a new replacement
http://www.aliexpress.com/item/Free...ENT-BATTERY-C11P1424-3000MAH/32396187338.html
Sammaul said:
Did you replace the glass only, or the entire screen assembly?
Click to expand...
Click to collapse
Entire screen replaced, to separate the glass is really difficult
gipikay said:
This is the one I've ordered, even if it says for ZE550ML (mine is 551) the part number and battery is the same (I think the difference between models is the screen resolution)
http://www.aliexpress.com/item/Free...ENT-BATTERY-C11P1424-3000MAH/32396187338.html
Entire screen replaced, to separate the glass is really difficult
Click to expand...
Click to collapse
If you install 550 screen on 551 phone, it's possible you must install rom for 550 on 551, the big difference is the dpi.
I was just commenting on batteries. My phone is 551 and used a 551 replacement LCD, no differences there
Ok sorry just my bad english
gipikay said:
This is the one I've ordered, even if it says for ZE550ML (mine is 551) the part number and battery is the same (I think the difference between models is the screen resolution)
Entire screen replaced, to separate the glass is really difficult
Click to expand...
Click to collapse
gipikay said:
I was just commenting on batteries. My phone is 551 and used a 551 replacement LCD, no differences there
Click to expand...
Click to collapse
Did you test it already? Does work?
Sent from my ZE551ML
gettohhole said:
Did you test it already? Does work?
Sent from my ZE551ML
Click to expand...
Click to collapse
The new battery has not arrived yet
But a couple of scares aside ( if I completely drain the battery, it takes a litlle longer to reach minimal charge to power on ), the old battery seem to hold for the moment.
EDIT: See post #21, the sellers sent me the wrong battery, I think it's for Zenfone 5. Now I'm waiting for AsusParts to ship me a new replacement
Be careful
If anyone tries this, use extreme caution. I exposed some cells on the battery and a little smoke came out. I don't really know what to do from here because I'm afraid to continue this further. I guess I'm out of a 300 dollar phone and 30 dollar screen
Hi all
I ordered ZE551ML for my ZE550ML .... and the person already shipped so couldn't change the order
is it ok or i have to ship it back?
is it only PPI and resolution ?
Hi guys
Failed ... Got the 551ML and mounted on 550ML
Screen turns on but no Asus initial logo etc... Is not working
Mounted all out of the box... Not removing completely the broken screen.
Main board and battery connectors only.
You guys think anything can help ?