Related
Hello,
I dropped my phone (O2 XDA Orbit) this morning and the plastic inset "border" for the screen has come loose on the right hand side and along the top. It looks like its been glued in place orginally and I'm wondering what glue I should use to repair it. Had a quick search through the forums on the site but didn't find anyone talking about this.
Cheers.
Dave.
Dont use super glue as it will likely go white and ruin your screen. Your best bet would be to have the phone professionally repaired. Alternatively, if thats not an option, try a little evo-stick (contact adhesive) sticks like crazy i fused properly. Or theres always "Gorilla Glue" if you can source it on the net, but it needs water as part of the chemical reaction...
nid
dwatkins said:
Hello,
I dropped my phone (O2 XDA Orbit) this morning and the plastic inset "border" for the screen has come loose on the right hand side and along the top. It looks like its been glued in place orginally and I'm wondering what glue I should use to repair it. Had a quick search through the forums on the site but didn't find anyone talking about this.
Cheers.
Dave.
Click to expand...
Click to collapse
I had a bigger problem, I put my full bodily weight on the phone. double and triple cracks along the screen. I bought a new screen and casing on http://cnn.cn for 150 dollars got it within 1 week.
Replacing screen and body is rather easy - do get the right screwdriver here for the very very small screws in body (4) and holding the main pcb (3)
got the original screen - the stickyness of the top layers = touchscreens is rather good. so I wonder how hard you dropped the gizmo
Hi,
Just purchased a TP2 with a cracked digitizer. I also have the replacement. I've done a bit of research, and it looks like a ton of steps. I'm pretty confident I can do it, so all I'm really looking for is some tips. Any surprises I might see that may not have been covered in this guide? This is what I have so far:
http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
how did you conclude that your digitizer is cracked?
The LCD is fine. It's the top layer of plastic that is cracked. I haven't received the phone yet, but I inspected it, and that's what I concluded. The person who sold it to me is including a replacement part, but I know I'm looking at a lengthy process to dismantle the device.
Do you have to take apart the entire phone just to change the digitizer? I thought you could just hook something underneath the corner and pry it out.
It seems like such a drag if you have to take the whole phone apart to change an exterior item.
Man you're in for a world of hurt and frustration... Easier to just purchase and replace the LCD and digitizer together...
But hey, good luck.....
have you managed to replace the digitizer only? if its such a mission why are so many people selling them on ebay? a scam maby lol?
i too am interested in your results, just now bought a cracked LCD htc touch pro 2 for $100, touching the screen works, except that the phone is stuck in head-set mode and can't seem to get out of it. also, i want to replace the lcd and use the phone myself. can you pls post your success/educational steps which you followed. also, where did you buy the replacement LCD? how much ? pls help.
ultramag69 said:
Man you're in for a world of hurt and frustration... Easier to just purchase and replace the LCD and digitizer together...
But hey, good luck.....
Click to expand...
Click to collapse
Totally agree here. From what I have read you dont want to mess around with trying to pry the current digitizer off and then reapply a new one on. It's a HUGE pain in the ass. Just purchase a replacement LCD screen/digitizer combo and i's apparently super easy to swap out.
I've taken apart tons of phones, I'm currently waiting on a digitizer to replace for my TP2. If you search this forum you will find instructions how to do it.
While waiting I've been reviewing the instructions.
As always the hardest part is putting it back together.
The only thing I can recommend to you is to don't worry about replacing it. Take pictures with a digital camera as you go so you can know how to put it back together.
Hopefully I will get mine by this weekend. It is for a T-Mobile TP2 and the only shop to have one available was in Hong Kong.
Good luck.
Redman0570 said:
I've taken apart tons of phones, I'm currently waiting on a digitizer to replace for my TP2. If you search this forum you will find instructions how to do it.
While waiting I've been reviewing the instructions.
As always the hardest part is putting it back together.
The only thing I can recommend to you is to don't worry about replacing it. Take pictures with a digital camera as you go so you can know how to put it back together.
Hopefully I will get mine by this weekend. It is for a T-Mobile TP2 and the only shop to have one available was in Hong Kong.
Good luck.
Click to expand...
Click to collapse
Hi, can u post how you go with this e.g. is it easy enough to seperate the lcd and touchscreen. Maby a few pics as well if you can.
Cheers
It can be done but it requires ALOT of patience. Take it slowly and try not to leaver against the LCD in anyway. If you do break the screen when replacing it a replacement isn't expensive.
I replaced the digitizer twice. Taking the phone apart and assembling it back is difficult only when you do it for the first time. Once you know what's going on it just takes some time and precision. The REALLY tough part when replacing JUST the digitizer is putting the lcd and digitizer together without any dust or fingerprints in between. I ended up with dusting and vacuuming the room, putting some super-clean brand new plastic bags around the workplace and putting the cold shower on. Then using super-clean glass polishing microfibre cloth and anti-static glass cleaning liquid under really good lamp I managed to get both parts 100% clean and put them back together. Don't forget latex gloves (the ones that leave no marks) - fingerprints are hundred times worse than dust to get rid of. I have no idea how long did it really take but when I finished my back hurt like hell and water was dripping from the ceiling
Separating lcd and digitizer is not too hard. It was easiest when it was still attached to the bezel. I just pried it out applying easy, firm pressure and taking my time. Try not to damage the sticky layer on the edges or get it excessively dirty - it'll make your life easier later.
I hope it goes easier for you. Gud luck!
EDIT: Make sure that lcd is positioned 100% correctly (there is 1 or 2mm space to move it around). It is a very unpleasant surprise to put the phone back together just to find out that some top or bottom pixel lines are permanently invisible (The Voice of True Experience speaks here:/). And generally - keep the place around you tidy - maybe some containers for screws, parts, tools and that sort of stuff. I am not naturally anal enough to start from this point but found out in the process that this sort of job gets extremely frustrating and exhausting when you get confused, start losing parts etc.
It is major hurt! The TP2 is really not user serviceable! Anyway after reading all instructions I still screwed it up. I should have sent it in to HTC. I would not recommend changing the digitizer on your own.
Everything went well until it came to removing the LCD & replacing the digitizer. I cut the speaker cable, and the LCD just came apart. Luckily I have another LCD, looking for a speaker cable now.
has anyone found any places that sell the lcd and digitizer together for the T-Mobile TP2?
Thanks to these instructions I was able to replace the broken digitizer (glass) on my TP2. Unfortunately the Russian instructions stop short of replacing the glass.
Tools required: T5 torx mini screwdriver, letter opener, mini philips, a mini straight screwdriver and I found a very mini (1mm ) straight screwdriver handy for getthing the keyboard and screen back loose. The letter openner and two straight screwdrivers are only for prying
Here is what I did from the last spot on the Russian instructions: (yes you have to do every step)
Note: Be very careful removing the ribbon taped to the back of the LCD. You have to pry the speaker out ot the case up at the top; don't attempt to remove it by pulling on the ribbon. Once the speaker is loose (it's attached to the riboon, you are ok to remove it.
1. Take a small straight screwdriver and pry all around the LCD (metal back with handwriting on it in the last photo.) There are plastic tabs all around it centering it. You can pry gently against them. The LCD is only adhered with a small gasket around the edge of the glass. It is not glued to the screen as was posted by someone else. It comes out fairly easily.
2. Remove the black tape holding down the ribbon connected to the digitizer. I wasn't able to save the tape but not a big deal. Below the tape is one of three screws holding the buttons on. Remove those three screws.
3. Now you should be able to remove the digitizer. Go slow starting at the bottom. It is glued all around at heavily glued at the top. I had the pry the top away with small flat screwdriver and a letter opener. Go slowly and eventually it will release. At the top of the glass is the speaker for your ear. It will likely come off with the glass. Remove it and return it to the now empty case centering it in top.
4. Using gloves to prevent prints remove the protective film form your new digitizer. There is a lot of static generated when you do this so keep it away from everything for a minute while it neutralizes. Then place the digitizer in from the top, feed the ribbon through the slot and press the plastic all the way around.
5. Replace the buttons and the screws that retain them.
6. Replace the LCD; you can't screw it up the plastic tabs center the LCD. Just make sure the ribbon is at the bottom.
7. Reverse the instructions in the Russian link at the beginning of the post.
All told it took one hour the first time. I got it all together and then screen didn't light it. I had trouble reconnecting the screen ribbon during assembly so I figured the problem was there. I took the phone apart (to the end of the Russian instructions) and reinserted the screen ribbon into the connecter and then reassembled the phone. It took 10 min to disassemble and reassemble the phone the second time although I didn't have to take apart the screen.
So that's it. It cost me $22.00 for a new digitizer and $10.00 shipping, which is a lot better than a new phone if you don't have insurance and the phone looks like new. If you look very hard you can make out one tiny speck of dust under the glass but it's barely visible; much better than looking at the large V shaped crack I had before.
Hello!
I ordered (and received) a screen AND a digitizer. But there's a thin scotch tape that make the screen+digitizer (in one piece) get stick to the phone. OK, I teared it off.
But, how can I replace this scotch tape??? Much less of 1 mm thick, it seems to be made of foam...
Anyone can help me???????????
Please....
Coucou !
Is there anybody out there?
(Pink Floyd, The Wall, 1979 )
I was sent a Digitizer from Ebay (without LCD). Just for everyone elses benefit, there is no way you can remove the digitizer from the LCD Screen. It's glued down. Maybe it wasn't the case with the older ones, but mine can not be separated, no way!
Taking the phone apart is not too hard, the video instructions are pretty good, but seriously, forget trying to replace the digitizer only.
Here is the video:
http://www.youtube.com/watch?v=MrTRPTmoxpw&feature=player_embedded
Cheers, Mal.
If it has the same construction as the HD2, you can put the LCD + digitizer in the oven for 5 minutes at 50 degrees celcius. This was shown in instructions by HTC. Then you can seperate them.
Maybe, but my LCD was glued across the whole screen not just the edges. I'd suggest only buying the Digitizer/LCD combo if you want to do this yourself. If you buy both (as a single piece) the job would be pretty easy.
I have searched high and low for an answer on how to replace a scratched screen of the SGS2 by yourself and have finally found the answer.
This will definitely VOID YOUR WARRANTY so don't say you haven't been warned.
I suggest you only use this guide if you were desperate like me. My phone didn't come with an official warranty so I was as good as screwed if I wanted a new screen.
Step 1: Obtain the part
Just ebay for lcd screen and digitizer galaxy s2 (however u may wish to buy it with the faceplate see below note). You want both the super amoled plus screen and the digitizer together. You can get this for about 120-130 USD.
There are some vendors that sell just the 'lens' but you need a specialized machine to replace it and is simply not worth the trouble.
Note that if you go to an original Samsung service centre, when they order the part, it comes together with the face plate and is therefore a breeze to install. This part is for sale on Ebay too. http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0. I would recommend you to buy this type instead of just the LCD and digitizer.
Follow this disassembly guide (not mine).
Now using a thin metal flat tool with a wide flat surface area, dig at the small gap from the top of the screen and pry the screen from the frontplate. It is held entirely by double-tape so don't worry about any screws, catches. Be careful of not damaging the bezel in the process.
Clean off the old black tape and double tape as best as u can, and be careful of the bottom buttons. The attachment shows how it looks like after cleaning it.
Reapply the double tape in strips and try to shape it to fit as much as you can. This is tiresome but necessary since the adhesive behind the lcd screen is very weak and you don't your screen falling out of you halfway.
Push it in and it should stick. That's it! Then reassemble.
Confirmed working!
thanks for the write up, do you have any more photos of your process?
OMG, it's like watching an autopsy.
Could a better resolution screen or even 3d screen be used/upgraded later on?
Nice to know for something happens, Hope not
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Man,,u shud handle it a bit gently ,,,,i mean,i flinched every time u "threw" the phone on the table.
On second thought, I might as well buy that screen protector
Sent from my GT-I9100 using XDA Premium App
wow that is the definition of T H I N !!!!!
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
Thanks also full part with bezel here http://www.ebay.co.uk/itm/Samsung-G...062?pt=LH_DefaultDomain_3&hash=item3cb9ff0e4e
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable
http://www.ebay.co.uk/itm/LCD-Touch...669?pt=LH_DefaultDomain_3&hash=item3cb9ff0cc5
Samsung Galaxy S II 2 i9100 LCD Touch Digitizer Screen
With Housing Bezel front cover ,Home Button, Flex Cable Without Samsung logo
White house soon on site
psp888 said:
thanks for the write up, do you have any more photos of your process?
Click to expand...
Click to collapse
Unfortunately not at this time. I will do it the next time around (which will be soon as there is a slight imperfection with my button sensitivity so I might be inclined to try it again) but trust me it's not a beautiful process. Needs lots of guts. Nothing technical about it. Shove the flat tool in the gap and keep on loosening the glue as much as u can then take it off.
podgo said:
Hope wont be necessary. How did you scratch the screen so hard that it had to be changed? I tought the Gorilla Glass is almost unscratchable.
Click to expand...
Click to collapse
It's more like cracked. I dropped it on some rocks from waist height and it cracked. It seems that gorilla glass is not shatter proof. There are also some scratches/mini cracks from where the rocks cut it.
Lesson learnt, get a screen protector that hopefully will reinforce it a bit more.
I wonder how these replacement parts compare to the quality of the original parts.
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
psp888 said:
Is your new screen a Super AMOLED+ screen? all ebay listing just says LCD. Is it original Samsung part?
Click to expand...
Click to collapse
There some listed as Super AMOLED+ screen just search on ebay or even drop the sellers a question about their iteams.
It is a Super Amoled + screen (don't see any difference in quality between the old and new one). Most sellers don't really know much of their products unfortunately but they do say it's original and I do believe mine is.
There's no Samsung print on the front plate but it does have a part number which corresponds closely to the original one. Everything else looks exactly the same, even the black sponge at the back and the microchips have Samsung wording on them.
BarryH_GEG said:
OMG, it's like watching an autopsy.
Click to expand...
Click to collapse
I have stomach to watch dead bodies, but not a GSII LOL
Dropped SGS2 from bikemount : broken screen.
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
DirkB19 said:
OK,
I broke my screen this weekend. I was on a bike tour with the SGS2 mounted on the steering bar. For some unclear reason, the universal holder came off the bikemount at 25 kmh... Dropped on the paved road, and although still in the universal holder, which is made of soft rubber (which I would expect to break the fall), the screen of my beloved SGS2 was cracked !!! Apart from the cracked screen, everything else seems to work as before.
So, today I ordered a replacement set with bezel from aliexpress.com at 148USD.
When I get the part, I will try to post some pictures of the replacement process.
I had an HD2 before ... just sold it last Friday :-( ... I think over a period of 1,5 year, I dropped the HD2 about 6 times on hard surfaces ... also it fell off my bike once ... the HD2 never broke.
So, is it just bad luck this time, or is the built quality of the SGS2 just not as good as the HD2 ?
Regards,
DirkB
Click to expand...
Click to collapse
It is very easy to do. Just unclip each component and transplant it to the new case.
I have to do my friends one this weekend as he has dropped it and damaged the screen and the bezel .
I have managed to source the screen and the bezel for him all as one piece .
Now all the guides i have seen just rip the phone to pieces , surely if we have the right bits like i have bought this fix is very smple to do??
I am thinking it is just a case of undoing the 7 screws at the back of the phone , opening it up and then disconnect the screen cables from the mainboard . Does the whole front then come away??
If not i take it i have to undo the screws on the main board to release the screen? but this means the componets of the main board may come loose etc??
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
buxz777 said:
Has anyone that has done this got any info on just swapping the screen with the complete part? when i say complete part i mean the one that comes with the bezel and home button etc like this
http://cgi.ebay.com/LCD-Touch-Digit...312?pt=LH_DefaultDomain_0&hash=item3a682b9ad0
Thanks in adance for any guidance
Click to expand...
Click to collapse
+1 for me.
I received my screen including bezel.
I've removed the main board just like the guy in the Youtube video.
But now I still have to transfer (from original front to my new front):
- the bottom PCB (where the microUSB sits)
- the camera
- the speaker
etc ...
I can not find a description/movie of how to do this ?
The bottom PCB for example has 2 screws, but after removing them the PCB itself looks like glued to the front assy'.
I prefer to see or get proper instructions before starting the rest of this adventure
...
PS : I got my part from aliexpress.com within 2 weeks (via airmail). It's with the Samsung logo on it and the package included all required tools (screwdrivers) to do the job. Would be nice to see some written instructions included as well.
Grtz,
DirkB
Hi, has anyone replaced their digitizer on their desire z/g2? How did it go? It looks easy on the youtube vid.. have any problems? What way did you use to melt the glue? What digitizer did you use, where from?
Any info much appriciated as will be replaceing mine v soon due to 'invisible finger problem' that's driving me nuts..
Thanks..
Sent from my HTC Vision using XDA App
Never done it on a g2 but should be pretty straight forward especially with a video lol. Use a heat gun to melt the glue, pretty much the only tool you SHOULD use to do something like that.
I replaced the digitizer on my third G2 after getting a refurb replacement from T-Mobile that had a black spot inside the actual digitizer glass, not on the outside or inside.
The process is very easy with the video, however, trying to keep dust and fingerprints from getting on the inside of the phone while you're trying to get it back together is a serious pain in the rear! If it's the same video that I watched, just use a hair drier blowing hot air to heat the adhesive on the inside of the digitizer and then pop the digitizer off very very slowly, because you don't want to accidentally bend the metal bezel around the screen.
You also may want to leave the original leftover adhesive on the inside, because when I cleaned mine off, light now always leaks out around the bottom edge of the digitizer, below the menu, home, and search buttons, even though I used the double sided adhesive strips covering the entire length of the bottom, so light shouldn't technically be leaking out. No biggie, though... it works like brand new, now!
Thanks for the reply.. I have seen that video and that's what I was using as a guide.. I ordered the digi today, should be here tomorrow.. the only thing I was wondering was the glueing process, as I have not ordered the double sided glue/tape stuff, as I was just hopeing to still use the original glue as I think you are saying.. I hope that works! Have to be careful like u say with dust/fingerprints etc..
Sent from my HTC Vision using XDA App
Hmm, after reading your post again, maybee I should of bought the double sided tape afterall? Do you think the old leftover glue is enough for the new digi?
Many thanks..
Sent from my HTC Vision usingall XDA App
Run over to radio shack they must have some kind of glue you can use lol. google cell phone screen glue see what info you can find.
Ok, just incase anyone is interested, got my new digitizer, followed the video, used a heat gun cerfully to melt the glue, pulled the old digitizer out, and used the original glue whilst still warm to hold the new digi in, as all of glue stayed on the case rather than on the digi, which was pretty lucky.. put it all back together and everything perfect, touchscreen back to how it should be.. cost me 17 pounds.
Sent from my HTC Vision using XDA App
How was this accompilshed?
I replaced the touch screen as well and the problem persists. Plus I never ran into a part that required a heat gun did I use the wrong item?
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
senser1080 said:
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
Click to expand...
Click to collapse
So which digitizer did you end up buying and which guide or video did you follow? I am about to tear mine apart and could use the info.
senser1080 said:
A VERY confusing part is getting the midframe to hold to the hinge mounts. The side (black dots all down it) should overlap the stabilizer bar on the hinge. I fidgeted with it for hours until realizing it goes over, and inadvertently damaged the highly sensitive LCD screen, which resulted in me taking the whole thing apart again to replace the LCD and digitizer. UGH!
DO NOT get the cheapo digitizer on Amazon, look for one with gray spots where the menu, home, back and search keys are on the back side. The digitizers without them will not work when you swap over the white button caps on the back. I feel like this information is vital to anyone who is replacing their G2 digitizer, but most guides and videos make no mention of it.
I used a lamp to heat up the glass to remove it the first time. Took too long the second time so I used a hair dryer.
Click to expand...
Click to collapse
Hi, I did buy mine from amazon.co.uk, there were a few for sale,, the one I bought was supposed to be a genuine t-mobile g2 replacement (refurb I think, pressumably this just means that it was from a second hand g2 that had problems and the digi was taken out - and I'm pretty certain this is the case as mine has a thin film (which u leave on) over the back of the digi covering the tracks etc, which had a few very small air/dust bubbles under it (just noticeable when screen off), where I own a desire z, so now it sais t-mobile instead of htc, but I can live with that.
The small grey bits that you talk about were floating about or stuck on my digi when I pulled it off the main chassis. I had a look, and as far as I could work out, were possibly just for giving colour to the tiny led's that give you light to the home/search keys etc (I may be wrong on their use), but if you look closely, the tiny grey things have even smaller rectangles on them that relate to the positions of the led's on the circuit board. So I picked the remaining ones off the old digi, put them back in their correct holes and stuck the new digi in. I've had no problems (with a digi from amazon with no little grey things on it) so far, but maybee this is due to mine being a second hand original part..
Edit : Now after reading your post again, you're talking about bits that are actually on the digi itself, not the white caps that I'm talking about! Whoops. I didn't notice any grey spots on the digi itself, but I guess I must have them..
Sent from my HTC Vision using XDA App
ian577416 said:
I replaced the touch screen as well and the problem persists. Plus I never ran into a part that required a heat gun did I use the wrong item?
Click to expand...
Click to collapse
I rekon u replaced the wrong thing! Maybe the lcd?
Sent from my HTC Vision using XDA App
i just replaced mine with this one:
http://www.ebay.de/itm/230685692541?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
actually it says HTC on it and looks a lil bit differently than on the picture.
never the less, i replaced it really carefully and checked every connecting.
But somehow the Touchscreen doesn't work at all.
Can anyone help me ? what could be the problem ?
Wrong digitzer ?
is it okay, that the digitizer has direct contact to the frame where it is glued to ?
jmpcrx said:
... as will be replaceing mine v soon due to 'invisible finger problem' that's driving me nuts..
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
Hi!
I have the same problem, I have asked it already here
So you had invisible finger press in the screen, and the screen was bad responsive?
...Just to make sure my problem is digitizer problem! The service wont change it in warranty unless the problem is there all the time! But its driving me crazy! why is it happening randomly, why isnt it all the time? How could i make the screen to do this problem when i'm at the service?
Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?