Note 2 recogniez in odin mode but not in normal - Galaxy Note II Q&A, Help & Troubleshooting

Hi!,
My note 2 is not recognized by windows, i connect it to the computer and it shows that is charging, but my computer doesn't even make a sound of a usb device getting connected.
But when i put the phone on odin mode, my pc recognize it normally, I could even install stock rom on it, but even with stock is not getting recognized.!!
Any suggestions!¡?
Thanks

What I've found with my GT-N7100 while trying to repair the IMEI is that if you dial *#7284# from the phone app, it takes you a "PhoneUtil" menu. If USB is set to "MODEM", Windows will not recognise the device, but if set to "PDA", it's fine.
As stock, mine was set to PDA and I believe this is what it should be.. but it might be worth checking that to see if it is set incorrectly.

darkriff said:
Hi!,
My note 2 is not recognized by windows, i connect it to the computer and it shows that is charging, but my computer doesn't even make a sound of a usb device getting connected.
But when i put the phone on odin mode, my pc recognize it normally, I could even install stock rom on it, but even with stock is not getting recognized.!!
Any suggestions!¡?
Thanks
Click to expand...
Click to collapse
well it may be the case where your usb port is malfunctioning as I too faced the issue and later found out the there was a problem with the port though it charged hopefully u have the latest drivers installled

shhbz said:
well it may be the case where your usb port is malfunctioning as I too faced the issue and later found out the there was a problem with the port though it charged hopefully u have the latest drivers installled
Click to expand...
Click to collapse
same problem in my n7100 also, do you means microUSB socket of N7100 was dead.

wangap said:
same problem in my n7100 also, do you means microUSB socket of N7100 was dead.
Click to expand...
Click to collapse
Weird thing is that yesterday trying *#7284# and putting the phone into modem/pda mode, the computer recognizes it as unknown device, and i dont think is the port because in odin mode my pc recognize it normally...

wangap said:
same problem in my n7100 also, do you means microUSB socket of N7100 was dead.
Click to expand...
Click to collapse
it was not completely dead as it was charging fine but it always failed to recognise in pc and driver installation failed so service center guy chk the usb socket on phn fixed it with new one and bam it detected in my laptop fine
darkriff said:
Weird thing is that yesterday trying *#7284# and putting the phone into modem/pda mode, the computer recognizes it as unknown device, and i dont think is the port because in odin mode my pc recognize it normally...
Click to expand...
Click to collapse
in my case the code help me to detect my phone in pc but still failed to proceed with driver installation and in the end again start charging the phone

shhbz said:
it was not completely dead as it was charging fine but it always failed to recognise in pc and driver installation failed so service center guy chk the usb socket on phn fixed it with new one and bam it detected in my laptop fine
in my case the code help me to detect my phone in pc but still failed to proceed with driver installation and in the end again start charging the phone
Click to expand...
Click to collapse
So, Do I have to change the microusb port?

darkriff said:
So, Do I have to change the microusb port?
Click to expand...
Click to collapse
Will this one fits?
http://www.ebay.com/itm/New-Connect...e_Replacement_Parts_Tools&hash=item4d0ac57451
Click to expand...
Click to collapse

darkriff said:
Will this one fits?
Click to expand...
Click to collapse
well it will work perfectly , but my suggestion would be to take it to authorized service center and get it done by them if not just be careful while opening the front panel of the phone as the silver panel get scratches easily and yes be careful to the network reception wire that is attached to it as it requires gentle handling when removing it out of the old one. maybe this video may help you http://www.youtube.com/watch?v=FfvOTFssDMM
Good Luck

darkriff said:
Will this one fits?
Click to expand...
Click to collapse
My Note 2 was repaired by replace the port board now.

ok, i replaced the usb port board, still same Issue :S

Related

Win doesn't recognize my Defy

Hello,
I've a big issue, if I try to connect the phone, via usb, to the pc windows none of the devices recognize the connection.
Nothing appear on the Defy. On the Pc, sometimes appear the "new device windows" but if I try to install drivers it show me an alert saying that the device is not installed correctly.
I've tried all the motorola drivers available but nothing happen. I've also tried 2 other pc and 2 other usb cable
Fortunally, the device is rooted and I can install a nandroid backup but I don't know how I can resolve this issue, someone can help me?
Thanks
nickee said:
Hello,
I've a big issue, if I try to connect the phone, via usb, to the pc windows none of the devices recognize the connection.
Nothing appear on the Defy. On the Pc, sometimes appear the "new device windows" but if I try to install drivers it show me an alert saying that the device is not installed correctly.
I've tried all the motorola drivers available but nothing happen. I've also tried 2 other pc and 2 other usb cable
Fortunally, the device is rooted and I can install a nandroid backup but I don't know how I can resolve this issue, someone can help me?
Thanks
Click to expand...
Click to collapse
Enable / disable USB debugging maybe? But normally there should be a prompt on the phone when you plug it in (pulling down the status bar usually asks you what to do, give memory card access, charge only...). Btw, does the Defy charge when plugged in or does the LED light up?
Arjoma said:
Enable / disable USB debugging maybe? But normally there should be a prompt on the phone when you plug it in (pulling down the status bar usually asks you what to do, give memory card access, charge only...). Btw, does the Defy charge when plugged in or does the LED light up?
Click to expand...
Click to collapse
Tried but nothing change. The phone doesn't charge correctly and no prompt message if I connect it to the pc.
And it is definitely not the cable and / or the USB port? Then it has to be a hardware problem on the phone's side I think.
Arjoma said:
And it is definitely not the cable and / or the USB port? Then it has to be a hardware problem on the phone's side I think.
Click to expand...
Click to collapse
Not the cable and not the USB
There's a way to reinstall all the Defy driver without the cable?
Try installing new moto drivers.
http://forum.xda-developers.com/showthread.php?t=1100585&highlight=rsd
Installed but no improvement on the situation. I think that's an hardware problem...
nickee said:
Installed but no improvement on the situation. I think that's an hardware problem...
Click to expand...
Click to collapse
Almost seems so : But charging works?
Arjoma said:
Almost seems so : But charging works?
Click to expand...
Click to collapse
Charging didn't work if I connect the phone to the pc, it's strange because if I connect to the electrical power it works.
I also think that I've had an issue when I've installed the custom firmware

Help! USB device not recognized

Since marshwallow update i can't connect with my lg g4 to windows pc. It's not the usb cable, or my pc, i've tryed with another phone and it works just fine. Any sugestion or should i return my phone to waranty?:crying:
AndreiMel said:
Since marshwallow update i can't connect with my lg g4 to windows pc. It's not the usb cable, or my pc, i've tryed with another phone and it works just fine. Any sugestion or should i return my phone to waranty?:crying:
Click to expand...
Click to collapse
Hello,
Since update on windows 10 and MM i've got some trouble too. You have to install lg usb driver from the lg phone and tell windows to stop auto install mtp drivers. Windows is always trying to install an old driver over the lg one and that's the problem.
You can also try to switch from regular usb to usb debigging in dev options several times.
nope, it still doesn't work. when i plug my old samsung galaxy s2 it just works like a charm. also i reinstaled usb driver with no fix. i'm not sure if it's hardware fault or software fault
AndreiMel said:
nope, it still doesn't work. when i plug my old samsung galaxy s2 it just works like a charm. also i reinstaled usb driver with no fix. i'm not sure if it's hardware fault or software fault
Click to expand...
Click to collapse
Does it charge at least ?
Zenouzenou said:
Does it charge at least ?
Click to expand...
Click to collapse
yes, the phone is charging
AndreiMel said:
yes, the phone is charging
Click to expand...
Click to collapse
Mine was the same. And when you swipe down notification for usb connexion cant you choose mtp ?
Try to uninstall the samsung USB driver or the drive which is affected yo your g4.
Zenouzenou said:
Mine was the same. And when you swipe down notification for usb connexion cant you choose mtp ?
Try to uninstall the samsung USB driver or the drive which is affected yo your g4.
Click to expand...
Click to collapse
it doesn't appear option to select MTP . also i've tryied to connect a usb flash disk and it doesn't read it via OTG cable. I think it's a hardware fault
AndreiMel said:
it doesn't appear option to select MTP . also i've tryied to connect a usb flash disk and it doesn't read it via OTG cable. I think it's a hardware fault
Click to expand...
Click to collapse
Looks like I have the same problem. Started off with Android Auto not detecting it, but it looks like the PC can't either, nor does it pick up an external USB DAC via the OTG cable :/
Did you have any success at all? Sounds like a hardware failure though :/
Sorry I just realised this thread was back in 2016 not 2017!
have same problem here, windows 10 x64, will try in other pc and see what happens.

Phone not working as a storage

I am on resurrection remix LP 5.5.9
When I connect my phone to pc it shows an error. I tried to clean the microUSB port but still doesn't work.
What should I do?
Below it's an image of the error
do you have Kies installed or universal usb drivers?
try different cable.
is there something on phone notification screen, like "charging, file transfer, MTP..."?
try different PC
2
yaro666 said:
do you have Kies installed or universal usb drivers?
try different cable.
is there something on phone notification screen, like "charging, file transfer, MTP..."?
try different PC
Click to expand...
Click to collapse
I have the drivers installed. No notification on phone. The OTG usb doesn't work too :crying:
bump!!
manuel1992 said:
bump!!
Click to expand...
Click to collapse
it charges ok?
see if Odin detects it in download mode
yaro666 said:
it charges ok?
see if Odin detects it in download mode
Click to expand...
Click to collapse
Yes it charges ok.
Odin doesn't detect it.
I have to say that when my battery dies it doesn't charge, I have to use another battery
Is the device in a UBS 2 port, or 3 port? Sometimes USB 3 still doesn't work for 'regular' card readers.
Have you tried to remove the driver from the device Manager and then start all over? Or update the driver?
Bright.Light said:
Is the device in a UBS 2 port, or 3 port? Sometimes USB 3 still doesn't work for 'regular' card readers.
Have you tried to remove the driver from the device Manager and then start all over? Or update the driver?
Click to expand...
Click to collapse
I used it on another computer, I don't think it's a driver problem

Usb drive/otg cable not detecting need help

Hello,my tab sm t705 not detecting usb otg cable,and usb drive when connecting to pc,its only showing charging but no prompt for mtp like it usually did,how to solved?
this happen after my otg drive often auto connect/disconnect a few times, thinking the cable broken,already buy a new one but still not detect.
My usb debugging is already tick,mtp+adb is already tick.
Tried factory reset but still not detect.
Already try googling but no result
Is this software or hardware problem?
BTw im using iron man rom & kernel.
cinmil said:
Hello,my tab sm t705 not detecting usb otg cable,and usb drive when connecting to pc,its only showing charging but no prompt for mtp like it usually did,how to solved?
this happen after my otg drive often auto connect/disconnect a few times, thinking the cable broken,already buy a new one but still not detect.
My usb debugging is already tick,mtp+adb is already tick.
Tried factory reset but still not detect.
Already try googling but no result
Is this software or hardware problem?
BTw im using iron man rom & kernel.
Click to expand...
Click to collapse
Check your win drivers in device manager. Ensure the Mtp driver is active.
Already check.not pc problem.and already installed samsung usb driver
cinmil said:
Already check.not pc problem.and already installed samsung usb driver
Click to expand...
Click to collapse
Fair do's but does it detect the device in device manager as an MTP device when connected?
Nothing detected on my pc except for mouse usb.no connection sound,nothing happen when the usb plug in,except my phone showing charging
cinmil said:
Nothing detected on my pc except for mouse usb.no connection sound,nothing happen when the usb plug in,except my phone showing charging
Click to expand...
Click to collapse
Have you tried just a normal USB cable to see if mtp works?
What u mean by that ?sorry a little noob about this.
But i have try connecting other phone.and its work perfectly fine.its detect as portable media..dont know what the problem with my tab.also i have try ant+ tester app.and its showing ant support built in firmware no service?is it normal?can anyone who have t705 try it?
cinmil said:
What u mean by that ?sorry a little noob about this.
But i have try connecting other phone.and its work perfectly fine.its detect as portable media..dont know what the problem with my tab.also i have try ant+ tester app.and its showing ant support built in firmware no service?is it normal?can anyone who have t705 try it?
Click to expand...
Click to collapse
For MTP you just need a normal USB cable not OTG.
This is result when using ant tester
ashyx said:
For MTP you just need a normal USB cable not OTG.
Click to expand...
Click to collapse
Ok understand wht u mean now,already done doing that.that wht i want to tell,showing nothing detect on my laptop eventough usb cable is already plug in.already check on device manager>root hub properties.and check what usb is connecting and only show the mouse usb.phone cable not detect on any usb root hub.
Solved
After a few days thinking of solution then i try to go download mode and plug the usb cable to pc and voila.usb updte installer pop up means its detecting now.and i cncel the updte and go to normal mode and its also detecting.mayb some software failure that its happen.btw i just uninstalled and installed new driver and let it updte after it detect the usb.problem solved.nearly changing new micro usb port?
cinmil said:
After a few days thinking of solution then i try to go download mode and plug the usb cable to pc and voila.usb updte installer pop up means its detecting now.and i cncel the updte and go to normal mode and its also detecting.mayb some software failure that its happen.btw i just uninstalled and installed new driver and let it updte after it detect the usb.problem solved.nearly changing new micro usb port?
Click to expand...
Click to collapse
Bro can you explain how did you solve the issue
sai143420 said:
Bro can you explain how did you solve the issue
Click to expand...
Click to collapse
Sorry bro.this post been too long.but from i remmember i donwload some app for pc.and enter my phone to download mode.maybe the app is official for samsung download mode.
What do you mean by download mode
---------- Post added at 03:18 AM ---------- Previous post was at 03:18 AM ----------
cinmil said:
Sorry bro.this post been too long.but from i remmember i donwload some app for pc.and enter my phone to download mode.maybe the app is official for samsung download mode.
Click to expand...
Click to collapse
What's that app name

Question Phone not connecting via USB

My first Poco F3 is completely unlocked and running a custom rom, still able to connect to PC even now.
I have a second Poco F3 that I was able to originally connect to my PC to debloat, hadn't needed to connect it to a PC till now. Today was the day I could unlock it but when I connect it via USB cable, original or otherwise, no usb options appear on phone and nothing shows on PC. I can use the same cable on my first Poco F3 and everything works fine. I've tried multiple cables, reinstalling drivers, restarting phone and PC, trying a different PC, enabling debugging tools, etc.
Nothing shows in "My Computer"
Nothing shows in Device Manager
No usb options on phone (default is set to File Transfer)
Nothing shows in CMD with "adb devices"
Charging still works
Is there anything I can do to at the very least unlock the bootloader? Or is this not fixable?
long shot... check the usb C port for dirt/dust/fluff blocking connection...
Most probably u debloated an app responsable for media transfer. If u can, revert what u debloated.
Alin45 said:
Most probably u debloated an app responsable for media transfer. If u can, revert what u debloated.
Click to expand...
Click to collapse
Did a factory reset thinking that may have been the case, still no good.
Tried cleaning out the port and still no good either
I still think it's Windows. Please can you try putting Ubuntu (or another Linux distro) on a USB, booting from that, installing platform tools (ADB/fastboot etc) and then running ADB devices. Windows is very finiky sometimes.
Edit: when you plug in your phone to the PC do you get a notification saying charging? Or is there no notification? Also does it start charging the phone?
There is a delay before it begins charging and the charging animation plays but yes it does. But then there is no usb notification. Will try ubuntu and report back
Booting into Ubuntu, before installing platform tools the first phone that I knew worked showed up and showed up in adb devices when platform tools was used. The second still didn't show up, exactly the same as on windows
Try downloading the installed stock miui rom from the update menu in the miui update menu and re-install it on the phone
Unfortunately reinstalling latest package didn't help
Can't think of anything else to suggest. Sorry
If the usb connection continues to be nonexistent, is there any way to at least unlock the bootloader without using the Xiaomi Unlock tool on the PC?
Are you sure the USB cable you're using support transfert file?
Cjayy said:
If the usb connection continues to be nonexistent, is there any way to at least unlock the bootloader without using the Xiaomi Unlock tool on the PC?
Click to expand...
Click to collapse
Nope
Hmmmmm.....strange! I'm running out of ideas....try different USB ports on PC. Maybe it's a faulty USB-C port on phone after all.
do you have a type c usb-otg?
If yes then see if it is detected by the phone
X0PIRAT3 said:
Are you sure the USB cable you're using support transfert file?
Click to expand...
Click to collapse
Yes. Used 4 different cables, 1 of which is the cable that comes with the phone. None work on this phone but do on the first phone.
Alin45 said:
Hmmmmm.....strange! I'm running out of ideas....try different USB ports on PC. Maybe it's a faulty USB-C port on phone after all.
Click to expand...
Click to collapse
Tried different ports across 2 PCs. I'm starting to think it is a faulty port, though it worked fine a week ago.
arifqur said:
do you have a type c usb-otg?
If yes then see if it is detected by the phone
Click to expand...
Click to collapse
I honestly don't know if any of my cables are usb-otg, how would I check?
Try to use this version of Mi FLash Tool (only for drivers) : https://xiaomiflashtool.com/download/xiaomi-flash-tool-20210226
Extract and launch the executable then drivers install
Something like this. You can plug in any usb stick and see if it is detected. Another way to check whether the port on the phone is working for data as well
X0PIRAT3 said:
Try to use this version of Mi FLash Tool (only for drivers) : https://xiaomiflashtool.com/download/xiaomi-flash-tool-20210226
Extract and launch the executable then drivers install
Click to expand...
Click to collapse
Tried this and still no good.
arifqur said:
Something like this. You can plug in any usb stick and see if it is detected. Another way to check whether the port on the phone is working for data as well
Click to expand...
Click to collapse
I don't have anything like this but that reminded me of the usb-c to headphone adapter and that also doesn't work. Sound just plays out of the speakers.
Trying with Android Auto in the car, the car doesn't register a device connecting at all either.
Either the data transfer portion is somehow disabled on the device itself (which I would love to know how to enable it again if that's the case) or it's a damaged usb port. Just strange that it worked a week ago.
Something I forgot to mention, when I went to unlock the bootloader yesterday the phone did not show up anywhere except for in the ADBFastbootTools to debloat the software as a OnePlus device but then never showed up again.
Cjayy said:
Tried this and still no good.
I don't have anything like this but that reminded me of the usb-c to headphone adapter and that also doesn't work. Sound just plays out of the speakers.
Trying with Android Auto in the car, the car doesn't register a device connecting at all either.
Either the data transfer portion is somehow disabled on the device itself (which I would love to know how to enable it again if that's the case) or it's a damaged usb port. Just strange that it worked a week ago.
Something I forgot to mention, when I went to unlock the bootloader yesterday the phone did not show up anywhere except for in the ADBFastbootTools to debloat the software as a OnePlus device but then never showed up again.
Click to expand...
Click to collapse
I have the same problem, did you solve it ? I replaced the usb board of the phone, still not working.

Categories

Resources