Develop Bugs

Unlocking bootloader HTC Tattoo -Spain

I've an HTC Tattoo and I'm trying to unlock the bootloader with the HTCdev bootloader unlocking. I do everything they say to do, but when it's time to put this command:
fastboot oem get_identifier_token
I get this error:
...
(bootloader) [ERR] Command error !!!
OKAY [ 0.007s]
finished. total time: 0.008s
I've removed and inserted the battery lots of times, reinstaled the drivers, searched information, but I couldn't find any solution.
I've S-On. I suppose it's not a trouble.
Thank you in advance!, you'll help me a lot!

I have the same issue with my HTC desire Z.
It shows following error:
...
(bootloader) [ERR] Command error !!!
OKAY [ 0.008s]
finished. total time: 0.008s
Is there another way to find identification token?

just wanted to update hboot

hey guys i just wanted to update hboot and now im stuck -.-
im german and my english is not the best...sry for that
but i hope one of you guys is able to help me with my phone:good:
phone is a One X brandet O2 ger
Cid is O2___102
Hboot is 0.94
radio 1.1204.90.13
i had a venom rom viper x (from oct 2012)
i wanted to update hboot and there was a step which said relock the device. yeah that was done no prob..
now i´ve a locked device (but i´ve got the unlock token from htc)
how to use that? already tried to put that into my phone via fastboot but there comes a error message
sending 'unlocktoken' (0 KB)... OKAY [ 0.009s]
writing 'unlocktoken'... FAILED (remote: unlock token check failed)
finished. total time: 0.224s
Click to expand...
Click to collapse
i think im not able to figure that out without any help
first i think to unlock the device again and after that just update hboot and then flash cm 10.1
thx for your help

To upgrade your Hboot... You first need to lock your device and then flash the firmware.zip!
After than unlock your device and then flash custom recovery and then install CM10.1
Post the result of the following code:
Code:
fastboot getvar version-main
If there's a RUU for your device, then you can go back to stock and then update to JB via OTA update if you want..?!
sending 'unlocktoken' (0 KB)... OKAY [ 0.009s]
writing 'unlocktoken'... FAILED (remote: unlock token check failed)
finished. total time: 0.224s
Click to expand...
Click to collapse
Generate a new unlock_code.bin file from htcdev.com and then try again!

vin4yak said:
To upgrade your Hboot... You first need to lock your device and then flash the firmware.zip!
After than unlock your device and then flash custom recovery and then install CM10.1
Post the result of the following code:
Code:
fastboot getvar version-main
If there's a RUU for your device, then you can go back to stock and then update to JB via OTA update if you want..?!
Generate a new unlock_code.bin file from htcdev.com and then try again!
Click to expand...
Click to collapse
+1 .. Here's the firmware thread >> http://forum.xda-developers.com/showthread.php?t=1957376 <<

[Q] bootloader error

I have a Desire without OS, it can boot into fastboot. Is there any way to know if USB debugging was switched on from here? I tried to unlock the bootloader, im on S-ON, but keep getting errors:
C:\Users\Alienanihilator\Desktop\Roms\HTC Roms\HTC One X\HTC_fastboot_files>fast
boot oem get_identifier_token
...
(bootloader) [ERR] Command error !!!
OKAY [ 0.016s]
finished. total time: 0.016s
Maybe has to do with USB debugging not being turned on before?

DrSmartphone said:
I have a Desire without OS, it can boot into fastboot. Is there any way to know if USB debugging was switched on from here? I tried to unlock the bootloader, im on S-ON, but keep getting errors:
C:\Users\Alienanihilator\Desktop\Roms\HTC Roms\HTC One X\HTC_fastboot_files>fast
boot oem get_identifier_token
...
(bootloader) [ERR] Command error !!!
OKAY [ 0.016s]
finished. total time: 0.016s
Maybe has to do with USB debugging not being turned on before?
Click to expand...
Click to collapse
You can't unlock the bootloader if it's not version 1.03.0001.
Flash the 2.3 RUU:
http://www.htcdev.com/process/legal_download/152

abaaaabbbb63 said:
You can't unlock the bootloader if it's not version 1.03.0001.
Flash the 2.3 RUU:
http://www.htcdev.com/process/legal_download/152
Click to expand...
Click to collapse
Thanks for the tip, I just did that, but still it keeps freezing when booting. Maybe some issue with the hardware I guess.

Help for write CID Unsuccess

I am trying write CID but unsuccess.
Blow is my command list.
c:\Adb>fastboot oem writecid 11111111
...
FAILED (remote: unknown command)
finished. total time: 0.011s

kevin469 said:
I am trying write CID but unsuccess.
Blow is my command list.
c:\Adb>fastboot oem writecid 11111111
...
FAILED (remote: unknown command)
finished. total time: 0.011s
Click to expand...
Click to collapse
you need S-OFF to change your CID

HI Thant,
Thanks for your reply. I got the method for this issue. My M9 already s-off as command should be at download mode.

kevin469 said:
HI Thant,
Thanks for your reply. I got the method for this issue. My M9 already s-off as command should be at download mode.
Click to expand...
Click to collapse
OK but when you are with M( why you post your question in ONE X forum

Hello Thant,
Thank you for your reply. Sorry my mistake post to ONE X forum, How can i move this post to M9 forums?

Return to S-on?

I bought a WWE HTC 10 to use in the states... I used sunshine and have s-off locked status, I changed the cid and mid to the unlocked us numbers and did a conversion using the htc ruu.exe, I have a red warning every time i start the phone about development purposes only etc... I figure this must have to do with the s-off so i want to set it back to on as though i just bought a usa unlocked model!
im in download mode
I tried the good old
Code:
fastboot oem writesecureflag 3
and i got this output
Code:
...
(bootloader) HTC KEY CARD VERSION: 7
(bootloader) VERIFY_BY_PROJECT_SIGN_KEY_FAIL hosd (-9)
FAILED (remote: Partition verify fail -9)
finished. total time: 1.024s
what am i doing wrong?

THC Butterz said:
I bought a WWE HTC 10 to use in the states... I used sunshine and have s-off locked status, I changed the cid and mid to the unlocked us numbers and did a conversion using the htc ruu.exe, I have a red warning every time i start the phone about development purposes only etc... I figure this must have to do with the s-off so i want to set it back to on as though i just bought a usa unlocked model!
im in download mode
I tried the good old
Code:
fastboot oem writesecureflag 3
and i got this output
Code:
...
(bootloader) HTC KEY CARD VERSION: 7
(bootloader) VERIFY_BY_PROJECT_SIGN_KEY_FAIL hosd (-9)
FAILED (remote: Partition verify fail -9)
finished. total time: 1.024s
what am i doing wrong?
Click to expand...
Click to collapse
Go to bootloader mode?
Sent from my SM-G935T using Tapatalk

didnt work in bootloader mode at all
Code:
...
FAILED (remote: unknown command)
finished. total time: 0.052s
didnt work in uru mode either
Code:
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot oem rebootRUU
...
OKAY [ 0.001s]
finished. total time: 0.002s
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot oem writesecureflag 3
...
(bootloader) HTC KEY CARD VERSION: 7
(bootloader) VERIFY_BY_PROJECT_SIGN_KEY_FAIL hosd (-9)
FAILED (remote: Partition verify fail -9)
finished. total time: 1.042s

THC Butterz said:
didnt work in bootloader mode at all
Code:
...
FAILED (remote: unknown command)
finished. total time: 0.052s
didnt work in uru mode either
Code:
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot oem rebootRUU
...
OKAY [ 0.001s]
finished. total time: 0.002s
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot oem writesecureflag 3
...
(bootloader) HTC KEY CARD VERSION: 7
(bootloader) VERIFY_BY_PROJECT_SIGN_KEY_FAIL hosd (-9)
FAILED (remote: Partition verify fail -9)
finished. total time: 1.042s
Click to expand...
Click to collapse
Actually if you still have the red warning then the Ruu likely didn't fully flash. You shouldn't have that message if it successfully flashes.
Sent from my SM-G935T using Tapatalk

dottat said:
Actually if you still have the red warning then the Ruu likely didn't fully flash. You shouldn't have that message if it successfully flashes.
Sent from my SM-G935T using Tapatalk
Click to expand...
Click to collapse
after speaking with jcase figgured out that because the ruu didnt mach the one the phone shipped with im sol for turning s-off back to s-on

THC Butterz said:
after speaking with jcase figgured out that because the ruu didnt mach the one the phone shipped with im sol for turning s-off back to s-on
Click to expand...
Click to collapse
Yeah I still believe that a fully flashed matching Ruu will clear that flag. Can you try flashing again and see if the dev flag clears?
Sent from my SM-G935T using Tapatalk