Develop Bugs

IPAQ 514 dead after flash of WM 6.1

Sorry for my poor english.
I've flashed my ipaq 514 with WM6.1 final (HP514[V1RC1L] from ifolder.ru)
but now it is bricked. When updating the process was slowly to 43% but then the progressbar has skip to 100% and device reboot.
After reboot i see only "No image exists !!" message.
Is this correctible or i have only brick which can i expose to waste?

ipaq blogsoft is respensable
I have the same probleme

Nobody helps ?

Nobody helps ?
ça fait deux jours que j'essais de resourdre le probleme sans aucune solution
je suis entrain d'avoir quelques idées dans ce lien
http://www.resco.net/forums/ShowPost.aspx?PostID=2804

sorry if the
text shown below is unreadable or with errors (thanks translate.google.com).
Malheureusement, ce n'est pour les fonctions PDA et les instructions de démarrage, mais 514 est un peu différente de la situation
back into my poor english:
In other words i don't know if this is applicable for IPAQ 514 and in post i've seen that device is alive (shows USB/Serial) but in this situation it seems no any interaction. I've tested to enter bootloader but with any of key combinations to enter bootloader mode , what i have found on the internet the operation was NOT successful.

no news at the moment
I find this text but i dont undrestand You just need the installed program DLLs.. what thos it meen
text :
RESOLUTION:
Use a Windows XP computer with active sync (4.5). Connection is not active, but this is no problem. You just need the installed program DLLs..
Connect the 514 to USB, it will show "connected to USB"
Start the upgrade...
If there is an error message "not found", stop the program and restart it.
Bios upgrade will start and after 2 minutes, the phone is running again...
Link : http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1197769

You need only dynamicaly linked libraries (DLL files) , you don't need full active sync , but this is not relevant to this.
In this case (from text that you find) is 514 alive and computer detects it, but in case what we need to solve (now minimaly for my ipaq) is problem in no communication. when i connect my 514 to my PC it does not found new hardware or do sounds like when you connect already known hardware. in other words PC does not recognize something on other end of the cable. And next problem is: author writes that ipaq or pc shows connected to usb but nothing seems to be applicable to this case.

I have the same probleme I've flashed my ipaq 514 with WM6.1 final (HP514[V1RC1L] from the Gost ifolder.ru)
but now it is bricked. When updating the process was slowly to 43% but then the progressbar has skip to 100% and device reboot.
After reboot i see only "No image exists !!" message.
I searching for resolution if I will have news I let it in forum
see you again

Solution!! - it worked for me
this has worked for me:
i assume that you have usb cable plugged into the pc
for english wm6 search hp SP38077
it must match your SKU ID (P/N) otherwise it says you have wrong version.my skuid is:FA908AA#ABB -> SP38077
i have windows vista installed and it works
1) take out the battery
2) remove USB cable if connected
3) insert battery
4) push and hold the silver center of the 4way key and press red phone key (switch on)
or see http://h20000.www2.hp.com/bizsuppor...=3375716&prodTypeId=215348&objectID=c01087938
this will make hard reset
5) computer now recognizes HP USB Sync
if no then remove battery
remove cable
insert battery again
then hold volume down (bottom part of the silver key on left side of phone)
and insert USB
now it will enter bootloader mode and if previosly not installed then now installs hp usb sync
now start HP Rom update utility with your preffered language (en or fr i dont know)
and it will connect to the phone and upgrade a firmware and voila phone is ALIVE !
Please post if you were successfull.

Alwase the same probleme
I make make hard reset with the first solution i see only "No image exists !!" message also whith the second solution and if i conect my device my pc not recognizes my device I'm very angry
there is a diference between HP USB Sync and Microsoft active sync
I dont understand what do you want to tell with HP USB Sync
I have Windows XP
Thank you for your help

Is that i must install Windows Vista
I wait or your help plase

Help me plase
IF I make make hard reset with the first solution i see only "No image exists !!" message also whith the second ; Are you see the message after you make hard reset ??
When I make hard reset with holding volume up and pressing red phone key (switch on) I have a black screen
Have you an idea palse
Think you

Nobody helps ?

i dont know if in XP shows HP USB Sync - but HP USB Sync is mode in which the device is visible for Rom Update Utility (almost in Vista) I will test it in VM
It so terrible with this communication it is so longly. Do you have an IM account (ICQ Skype MSN ?) If Yes then send me your number or nick in Private message and when i will be back to home (in 1 hour ) then we can test it online)

Think you my friend this is my ICQ Number or Email [email protected]

check your mailbox

Nobody helps ?

greeg said:
Sorry for my poor english.
I've flashed my ipaq 514 with WM6.1 final (HP514[V1RC1L] from ifolder.ru)
but now it is bricked. When updating the process was slowly to 43% but then the progressbar has skip to 100% and device reboot.
After reboot i see only "No image exists !!" message.
Is this correctible or i have only brick which can i expose to waste?
Click to expand...
Click to collapse
The same thing happened to me. Can anybody help out with this?

No image exists solucion
Buenas a todos, acabo de resolver el problema ayer:
1-lo primero que hay que hacer es quitar la bateria al movil y dejarlo asi unas cuantas horas o hasta el dia siguiente (a mi me funciono dejandolo hasta el dia siguiente)
2-en tu pc con windows xp, WINDOWS VISTA NO, repito WINDOWS VISTA NOO!!! instalar primero el microsoft active sync que viene en el cd de la caja
3-descargar e instalar el rom update para tu idioma de la misma pagina de hp
4-colocar nuevamente la bateria (despues de varias horas)
5-pulsar el boton de bajar volumen lateral y el de izquierda de control central y sin soltarlos conectar el usb al pc
6-ya no deberia aparecer no image exists, mas bien te aparece el mensaje de bootloader y que esta conectado via usb
7-iniciamos el room update que hemos descargado
8-luego de unos minutos el movil vuelve a estar operativo
aclaraciones:
-esto no funciona en windows vista y probablemente si pruebas actualizar ahora el wm6.1 si funcione, siempre y cuando la actualizacion la hagas desde un pc con windows xp (aun no lo he probado)
-tienes que dejar el movil sin la bateria varias horas ya que al principio lo probe sin hacerlo y no me funciono, solo funciono luego de dejarlo sin la bateria por varias horas
-para poder iniciar el room update que se descarga de la pagina de hp tienes que tener instalado antes el microsoft active sync que viene en la caja con el movil de lo contrario te dira que no encuentra un dll
-un dia lleve el movil a un servicio tecnico y me dijeron que no se podia reparar, me gustaria enseñarles tambien como se hace
suerte a todos

Simple Root and Custom Recovery Installation (testers needed)

Read carefully please!
Froyo and Windows users only at this moment, very busy this days, will make it work with linux and mac os!:
For those who flashed the SBF file with RSD Lite.
Im just trying to make it all easier.
Click to expand...
Click to collapse
You dont need adb installed on your PC!
TIPs: pass MOTOBLUR SETUP.
When you are on the begining of motoblur setup after you flashed your phone, (long press menu) to use the keyboard then type: eebluroff.
You must be done now!
Click to expand...
Click to collapse
Download the zip file and unzip it wherever you want.
Enable "USB debugging" on the phone before proceeding.
Settings -> Applications -> Development -> USB debugging.
1 - Connect your phone to PC (wait for your PC to install drivers) and click on "Install Gingerbreak & 2ndInitDefy".
Note: When commands window closes automatically, check if Gingerbreak and Defy 2init are installed on the phone (MOTOROLA SIDELOADER IS INSTALLED TOO to enable non-market apps), if they are everything is going fine.
2 - Unplug the phone from your PC.
3 - Open Gingerbreak installed on your phone and click on "Root device", (it will take a while) later your phone will reboot when completed.
4 - When your phone boots, go to 2ndinitDefy installed on your phone and download a recovery (try lastest version).
5 - Turn off the phone and turn it on, when you see the led light is blue press volume down button.
You are alredy into bootmenu ready to flash!
Click to expand...
Click to collapse
Donwload:
http://www.mediafire.com/?6kbt33kx64xg11e
I tested it on my PC but I need somebody else to test it, I have adb installed on my PC, need somebody who does not have it installed.
You wont need superoneclick anymore to root!
I will make a video later! I installed Ubuntu I will try it in linux to make this work for every OS and why not MAC OS!

josuearisty said:
Froyo users only:
For those who flashed the SBF file with RSD Lite.
Im just trying to make it all easier.
Testers needed
You dont need adb installed on your PC!
Download the file, unzip it wherever you want.
Remember to enable "USB debugging" before proceding.
Settings -> Applications -> Development -> USB debugging.
Then click on "Install Gingerbreak & 2ndInitDefy"
1 - Open Gingerbreak installed on your phone and click on "Root device", your phone will reboot when completed.
2 - Go to 2ndinitDefy installed on your phone and download a recovery (try lastest version).
Donwload:
http://www.mediafire.com/?6kbt33kx64xg11e
I tested it on my PC but I need somebody else to test it, I have adb installed on my PC, need somebody who does not have it installed.
You dont need superoneclick anymore to root!
Click to expand...
Click to collapse
Hola puedes poner las instrucciones en español y para que sirve ...perdon x mi ignoracia es
Es mejor Gingleblur q froyo cuales son las ventajas y las contras...saludos amigo....

Hi there,
May I know if there is a way to switch from CWM recovery to TWRP? I tried to simply flash the zip for TWRP but then my bravo won't start...
Thanks.

mataflakitas said:
Hola puedes poner las instrucciones en español y para que sirve ...perdon x mi ignoracia es
Es mejor Gingleblur q froyo cuales son las ventajas y las contras...saludos amigo....
Click to expand...
Click to collapse
Voy a hacer guias en español para cada thread que he creado
Esto es para si algo te ha salido mal y tu telefono no quiere iniciar quedandose solamente en el logo de moto y tienes que por desgracia FLASHEAR el SBF de Froyo con RSD LITE.
Entonces despues que estes en Froyo, podras seguir estos pasos y no tener que usar superoneclick, en mi opinion esto es mas facil.
Pruebalo cuando puedas!
brucezyc said:
Hi there,
May I know if there is a way to switch from CWM recovery to TWRP? I tried to simply flash the zip for TWRP but then my bravo won't start...
Thanks.
Click to expand...
Click to collapse
I try doing it too but no success, I think you should flash first a custom rom, then you will be able to flash touch recovery and it will for sure work.
I will let know about some test I make!

I'll be honest, I didn't try it, but it will work. That's really not a bad idea and would work with any phone Gingerbreak works on....You should release that in Android General.
I would use it, I'm just too lazy to flash an sbf and then set my phone back up again. I'm happy with my Bravo for the moment...and its my onlyl phone...That really is a simple, yet useful, solution.

gracias
josuearisty said:
Voy a hacer guias en español para cada thread que he creado
Esto es para si algo te ha salido mal y tu telefono no quiere iniciar quedandose solamente en el logo de moto y tienes que por desgracia FLASHEAR el SBF de Froyo con RSD LITE.
Entonces despues que estes en Froyo, podras seguir estos pasos y no tener que usar superoneclick, en mi opinion esto es mas facil.
Pruebalo cuando puedas!
I try doing it too but no success, I think you should flash first a custom rom, then you will be able to flash touch recovery and it will for sure work.
I will let know about some test I make!
Click to expand...
Click to collapse
Oooo muchas gracias amigo voy a probar que suerte q hablas español estoy aprendiendo muchas cosas contigo amigo josuearisty... saludos

oh no, i'm not unglug my phone after install Install Gingerbreak & 2ndInitDefy, then i click Gingerbreak to root
and now it's not on (, just have logo motorola
help me
now i'm ok, i wipe data, cache and do it again
but i dont click root on Gingerbreak , but on my phone still have superuser icon ? it success or not
i used superoneclick to root, but not success after i installed Gingerbreak & 2ndInitDefy

skeevy420 said:
I'll be honest, I didn't try it, but it will work. That's really not a bad idea and would work with any phone Gingerbreak works on....You should release that in Android General.
I would use it, I'm just too lazy to flash an sbf and then set my phone back up again. I'm happy with my Bravo for the moment...and its my onlyl phone...That really is a simple, yet useful, solution.
Click to expand...
Click to collapse
I think it is still not that simple, I will post some tips and be more specif.
mataflakitas said:
Oooo muchas gracias amigo voy a probar que suerte q hablas español estoy aprendiendo muchas cosas contigo amigo josuearisty... saludos
Click to expand...
Click to collapse
Siempre mi amigo, cualquier cosa estamos aqui.
kevins547 said:
oh no, i'm not unglug my phone after install Install Gingerbreak & 2ndInitDefy, then i click Gingerbreak to root
and now it's not on (, just have logo motorola
help me
now i'm ok, i wipe data, cache and do it again
but i dont click root on Gingerbreak , but on my phone still have superuser icon ? it success or not
i used superoneclick to root, but not success after i installed Gingerbreak & 2ndInitDefy
Click to expand...
Click to collapse
Maybe you did not follow steps as you should, I think I have to make steps easier to understand, so that noobs and advanced users can do it all.
Thanks for trying!

when unglug the phone from Pc, the box USB debugging is tick in or not ?

kevins547 said:
when unglug the phone from Pc, the box USB debugging is tick in or not ?
Click to expand...
Click to collapse
Of course it has to be enable.
Else it is not going to work.

gracias
josuearisty said:
Of course it has to be enable.
Else it is not going to work.
Click to expand...
Click to collapse
amigo podra subir un video para saber con mayor facilida como se hace y las instrucciones en español bueno tambien para ingles claro... creo que novatos como yo ...avemos muchos en este foro y estariamos muy agradecicdo con usted amigo josuearisty ...
oye amigo otra duda que pasa si mi pc tiene adb instalado.... puede ocacionar un error en mi motorola bravo ...?
otra duda por que cuando baje su archivo mi pc me lo detecto como un virus...

mataflakitas said:
amigo podra subir un video para saber con mayor facilida como se hace y las instrucciones en español bueno tambien para ingles claro... creo que novatos como yo ...avemos muchos en este foro y estariamos muy agradecicdo con usted amigo josuearisty ...
oye amigo otra duda que pasa si mi pc tiene adb instalado.... puede ocacionar un error en mi motorola bravo ...?
otra duda por que cuando baje su archivo mi pc me lo detecto como un virus...
Click to expand...
Click to collapse
Esta semana estare algo ocupado, el video creo que lo hare la semana que viene.
Usar el adb del archivo no te va a ocasionar ningun problema, ni a tu telefono ni a la computadora.
La aplicacion gingerbreak tiene un exploit dentro y los antivirus lo identifican como un virus, solo desactivalo si lo vas a usar.
--------------------------------------------------------
If you have adb installed on your pc, using this one will cause no problem to the phone or your pc.
Your antivirus detects gingerbreak as a virus because of an exploit command inside the apk file, you can deactivate your antivirus and use it with no problem, no risk with it.

I'll add, s1c/rage against the cage/gingerbreak all show up as viruses because they are. Not kill you PC virus, but virus none the less. Technically they're exploits, but still get picked up by scanners.

Gonna need some testers for LINUX and MAC, when its ready I will you know people!

Working great!. Will flash a Rom right now . Thnx to make our life easier!.

Took a few flashes, but I got there in the end! Great stuff, thanks!!

Worked like a charm. Thanks!!

Cannot change Paging File In Nokia 920

Recently I updated my Nokia 920 to Windows 10 Mobile from 1511 to 1709
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then I tried to update the paging file.
I navigate to HKLM Local Machine\SYSTEM\CurrentControlSet\Control\Session Manager\Memory Management\PagingFiles and I change the 256 256 to 1024 1024.
Then I click the check mark.
Then I click on the PagingFiles and its still at 256 256
Whats going on?
Are my settings right? or is there something else I'm missing

You must have the device unlocked - Interop Unlock

uiqjirka said:
You must have the device unlocked - Interop Unlock
Click to expand...
Click to collapse
I tried too many times to Interop Unlock my Lumia 920, but when I put the slider into "ON", it goes fast to "OFF" position again.
Tried with Bootloader unlocked, Bootloader locked, Rooted and not rooted, trying all ways possible to get it Interop Unlocked, but always failed.
I don't know what is, but there is something different on Nokia Lumia 920 that makes not possible yet to unlock it with the way that rules with the rest of Nokia Lumia devices.
The ways are few differents between unlock Nokia Lumia devices and unlock Microsoft Lumia devices, but, either into same brand devices?

Interop Unlock with vcreg10

Primero estaría bueno que describas que pasos seguís para hacerlo, como para saber donde esta tu falla... Es practicamente imposible que tengas problemas para desbloquear un NOKIA.

xxJMarian said:
Primero estaría bueno que describas que pasos seguís para hacerlo, como para saber donde esta tu falla... Es practicamente imposible que tengas problemas para desbloquear un NOKIA.
Click to expand...
Click to collapse
1. Hard Reset
2. Downloaded Interop Tools from https://forum.xda-developers.com/showpost.php?p=73608163&postcount=1006
3. Installed dependencies and then installed certificate and then Interop Tools.
4. Restarted Phone.
5. Opened Interop Tools and set "Restore NDTKSvc" to ON.
6. Restarted Phone
7. Adjusted Registry settings HKEY_LOCAL_MACHINE (HKLM) > System > Platform > DeviceTargetInfo and the phone updated from 1511 to 1709.
8. Soft Reset
9. Attempted to update PagingFile from 256 256 to 1024 1024. Clicked the check mark, went immediatley back to the PagingFile and it was still at 256 256
10. Restarted Phone
11. Attempted to turn on "Interop/Cap Unlock". It would Not turn on. Attempted to turn on "New Capability Engine Unlock" it wound NOT turn on
Those are the steps I used

Ranger SVO said:
1. Hard Reset
2. Downloaded Interop Tools from https://forum.xda-developers.com/showpost.php?p=73608163&postcount=1006
3. Installed dependencies and then installed certificate and then Interop Tools.
4. Restarted Phone.
5. Opened Interop Tools and set "Restore NDTKSvc" to ON.
6. Restarted Phone
7. Adjusted Registry settings HKEY_LOCAL_MACHINE (HKLM) > System > Platform > DeviceTargetInfo and the phone updated from 1511 to 1709.
8. Soft Reset
9. Attempted to update PagingFile from 256 256 to 1024 1024. Clicked the check mark, went immediatley back to the PagingFile and it was still at 256 256
10. Restarted Phone
11. Attempted to turn on "Interop/Cap Unlock". It would Not turn on. Attempted to turn on "New Capability Engine Unlock" it wound NOT turn on
Those are the steps I used
Click to expand...
Click to collapse
Drive
0. Activate developer mode.
1. install the desktop installer that's inside my MSInstallers folder via file explorer, wait around 3~min for it to complete.
2. Install the dependencies of interop 2.0 one by one via file explorer, when it tells you to choose between enterpriseinstall or the other one, you select the other one (desktop installer).
3. Install interop 2.0.
4. Enter interop, select THIS DEVICE and proceed to the unlock tab. Enable restore NDTK and reboot the device.
5. After reboot, reopen interop and enable interop unlock and new cap engine.
6. Use registry browser or editor to change the pagefile.
---------- Post added at 03:05 AM ---------- Previous post was at 03:00 AM ----------
DaniDeVega said:
I tried too many times to Interop Unlock my Lumia 920, but when I put the slider into "ON", it goes fast to "OFF" position again.
Tried with Bootloader unlocked, Bootloader locked, Rooted and not rooted, trying all ways possible to get it Interop Unlocked, but always failed.
I don't know what is, but there is something different on Nokia Lumia 920 that makes not possible yet to unlock it with the way that rules with the rest of Nokia Lumia devices.
The ways are few differents between unlock Nokia Lumia devices and unlock Microsoft Lumia devices, but, either into same brand devices?
Click to expand...
Click to collapse
Te paso mi drive, descargate el desktop installer, las dependencias y el interop. A continuación vas a seguir los siguientes pasos:
CUANDO ENTRES EN MI DRIVE, EN LA CARPETA MSINSTALLERS ESTA EL DESKTOP INSTALLER Y EL INTEROP QUE VAS A USAR ES LA CARPETA INTEROP 2.0, AHI ESTA EL APPX Y SUS DEPENDENCIAS.
Drive
0. Activas modo desarrollador.
1. Instalas el desktop installer desde el explorador de archivos, nada del otro mundo, esperas unos 3~ minutos ya que el explorador de archivos no muestra progreso %.
2. Instalas las dependencias una por una, no importa el orden, pero instalas todas. Cuando las abras, te va a dar elegir si queres instalarlas con enterprise install o con el instalador de aplicaciones (desktop installer), vos vas a seleccionar el desktop installer. Y asi, le das instalar a todas y cada una.
3. Cuando ya hayas instalado todas las dependencias, vas a instalar el interop tools, no hace falta que instales el certificado.
4. Cuando terminas de instalarlo, lo abris, seleccionas THIS DEVICE el que es sin extensiones y vas a la pestaña de UNLOCK. Activas el slider de Restore NDTK y reseteas el telefono (mantenes el boton de apagar durante 10 segundos)
5. Abris interop tools, vas a UNLOCK y activas INTEROP UNLOCK, paso seguido activas NEW CAPABILITY ENGINE.
6. Vas al Registry browser y vas a la ruta del archivo de paginación, esto ya lo sabes asi que no te lo voy a explicar. La unica regla es que respetes los espacios de la sentencia. Una vez que cambies 256 256 por 1024 1024 le das click al OK que tiene un icono de Check. Volves a abrir el archivo para corroborar que se cambiaron, reinicias el telefono de nuevo y ya estas.

Gracias! / Thanks!!
xxJMarian said:
Drive
0. Activate developer mode.
1. install the desktop installer that's inside my MSInstallers folder via file explorer, wait around 3~min for it to complete.
2. Install the dependencies of interop 2.0 one by one via file explorer, when it tells you to choose between enterpriseinstall or the other one, you select the other one (desktop installer).
3. Install interop 2.0.
4. Enter interop, select THIS DEVICE and proceed to the unlock tab. Enable restore NDTK and reboot the device.
5. After reboot, reopen interop and enable interop unlock and new cap engine.
6. Use registry browser or editor to change the pagefile.
---------- Post added at 03:05 AM ---------- Previous post was at 03:00 AM ----------
Te paso mi drive, descargate el desktop installer, las dependencias y el interop. A continuación vas a seguir los siguientes pasos:
CUANDO ENTRES EN MI DRIVE, EN LA CARPETA MSINSTALLERS ESTA EL DESKTOP INSTALLER Y EL INTEROP QUE VAS A USAR ES LA CARPETA INTEROP 2.0, AHI ESTA EL APPX Y SUS DEPENDENCIAS.
Drive
0. Activas modo desarrollador.
1. Instalas el desktop installer desde el explorador de archivos, nada del otro mundo, esperas unos 3~ minutos ya que el explorador de archivos no muestra progreso %.
2. Instalas las dependencias una por una, no importa el orden, pero instalas todas. Cuando las abras, te va a dar elegir si queres instalarlas con enterprise install o con el instalador de aplicaciones (desktop installer), vos vas a seleccionar el desktop installer. Y asi, le das instalar a todas y cada una.
3. Cuando ya hayas instalado todas las dependencias, vas a instalar el interop tools, no hace falta que instales el certificado.
4. Cuando terminas de instalarlo, lo abris, seleccionas THIS DEVICE el que es sin extensiones y vas a la pestaña de UNLOCK. Activas el slider de Restore NDTK y reseteas el telefono (mantenes el boton de apagar durante 10 segundos)
5. Abris interop tools, vas a UNLOCK y activas INTEROP UNLOCK, paso seguido activas NEW CAPABILITY ENGINE.
6. Vas al Registry browser y vas a la ruta del archivo de paginación, esto ya lo sabes asi que no te lo voy a explicar. La unica regla es que respetes los espacios de la sentencia. Una vez que cambies 256 256 por 1024 1024 le das click al OK que tiene un icono de Check. Volves a abrir el archivo para corroborar que se cambiaron, reinicias el telefono de nuevo y ya estas.
Click to expand...
Click to collapse
Gracias!! Lo probaré esta semana sin falta.
Thanks! I'll give it a try into this week!!

xxJMarian SOLVED our Lumia 920 tweaking issue. THANK U!
I suggest all who came here trying to find a solution, to follow step by step this guide served by
xxJMarian
MANY THANKS to xxJMarian to explained us the way to do this on our Nokia Lumia 920.
xxJMarian said:
Drive
0. Activate developer mode.
1. install the desktop installer that's inside my MSInstallers folder via file explorer, wait around 3~min for it to complete.
2. Install the dependencies of interop 2.0 one by one via file explorer, when it tells you to choose between enterpriseinstall or the other one, you select the other one (desktop installer).
3. Install interop 2.0.
4. Enter interop, select THIS DEVICE and proceed to the unlock tab. Enable restore NDTK and reboot the device.
5. After reboot, reopen interop and enable interop unlock and new cap engine.
6. Use registry browser or editor to change the pagefile.
_SPANISH LANGUAGE EXPLAINED EITHER BELOW_
Te paso mi drive, descargate el desktop installer, las dependencias y el interop. A continuación vas a seguir los siguientes pasos:
CUANDO ENTRES EN MI DRIVE, EN LA CARPETA MSINSTALLERS ESTA EL DESKTOP INSTALLER Y EL INTEROP QUE VAS A USAR ES LA CARPETA INTEROP 2.0, AHI ESTA EL APPX Y SUS DEPENDENCIAS.
Drive
0. Activas modo desarrollador.
1. Instalas el desktop installer desde el explorador de archivos, nada del otro mundo, esperas unos 3~ minutos ya que el explorador de archivos no muestra progreso %.
2. Instalas las dependencias una por una, no importa el orden, pero instalas todas. Cuando las abras, te va a dar elegir si queres instalarlas con enterprise install o con el instalador de aplicaciones (desktop installer), vos vas a seleccionar el desktop installer. Y asi, le das instalar a todas y cada una.
3. Cuando ya hayas instalado todas las dependencias, vas a instalar el interop tools, no hace falta que instales el certificado.
4. Cuando terminas de instalarlo, lo abris, seleccionas THIS DEVICE el que es sin extensiones y vas a la pestaña de UNLOCK. Activas el slider de Restore NDTK y reseteas el telefono (mantenes el boton de apagar durante 10 segundos)
5. Abris interop tools, vas a UNLOCK y activas INTEROP UNLOCK, paso seguido activas NEW CAPABILITY ENGINE.
6. Vas al Registry browser y vas a la ruta del archivo de paginación, esto ya lo sabes asi que no te lo voy a explicar. La unica regla es que respetes los espacios de la sentencia. Una vez que cambies 256 256 por 1024 1024 le das click al OK que tiene un icono de Check. Volves a abrir el archivo para corroborar que se cambiaron, reinicias el telefono de nuevo y ya estas.
Click to expand...
Click to collapse

DaniDeVega said:
I suggest all who came here trying to find a solution, to follow step by step this guide served by
xxJMarian
MANY THANKS to xxJMarian to explained us the way to do this on our Nokia Lumia 920.
Click to expand...
Click to collapse
Glad to help! / Encantado de ayudar

Very Helpful

Redmi Note 8 Pro Hard Brick & Black Screen

Hi everyone,
I have a big problem since yesterday, I am under the version Miui 11 Android 10 rooted under TWRP unofficial and I wanted to install a Rom Custom, I of which wanted to install the official version of TWRP, when I have Flash Recovery Recovery.img after restarting... BLACK SCREEN I could not have returned to FASTBOOT mode and in RECOVERY only the NOTIFICATION which is on, when I stay press POWER + VOLUM UP I have a SOUND on PC like what the PHONE is connected for 5 SECONDS after it DISCONNECTS, so I followed a tutorial to open my phone and disconnect my BATTERY... always the same problem :/
if you can help me please :/
I would like to specify that I never know that when I wanted to put the official version of TWRP my phone was around 30% ... ?
Thanks you.

Test Point
Tiix31Dev said:
Hi everyone,
I have a big problem since yesterday, I am under the version Miui 11 Android 10 rooted under TWRP unofficial and I wanted to install a Rom Custom, I of which wanted to install the official version of TWRP, when I have Flash Recovery Recovery.img after restarting... BLACK SCREEN I could not have returned to FASTBOOT mode and in RECOVERY only the NOTIFICATION which is on, when I stay press POWER + VOLUM UP I have a SOUND on PC like what the PHONE is connected for 5 SECONDS after it DISCONNECTS, so I followed a tutorial to open my phone and disconnect my BATTERY... always the same problem :/
if you can help me please :/
I would like to specify that I never know that when I wanted to put the official version of TWRP my phone was around 30% ... ?
Thanks you.
Click to expand...
Click to collapse
I am writing this for anyone to use at their own risk, it is not complicated.
Once updated from Indonesia Miui 11 Android 9 rom to Android 10 and installed a recovery incorrectly and I have returned to
lock my Redmi Note 8 Pro (Begoña) and this time I have not waited for the battery to drain as in the previous one (post # 196)
I have used the Test Point method.
This is what I have done:
-Copied the folder from the Indonesian rom V10.4.2.0, once the zip is unzipped, in Computer> C
-Installed SP Flash Tool v5. 1924 Win also in C
-Removed the back of the mobile and removed the housing that is above the battery (Photo 1).
-Prepared a piece of fine copper wire, I have connected one end to a screw on the mobile plate making ground (Photo 2) and to
the other end I have connected a nail (Photo 4) .Then I have opened the Flash Tool and I have put the scatter that
*it is in the "images" folder of the rom that I had copied in C, and the DA and the authentication file that is in it
*Flash Tool folder and I have connected the usb cable to the mobile, only to the mobile.
-I pressed "Download Only" and connected the other end of the copper cable, prepared with a nail, in the
*point Kcol0 (Photo 3) and I have connected the usb cable to the computer. The bottom bar of the FlashTool has started to fill in
*color red first and then change color until the "Download Ok" symbol appears
*I have done it with the battery disconnected (others say it is connected) and with all the files marked on the
*Flash Tool (others say that you only have to mark the preolader) and it has worked for me.
*
After a few minutes the mobile has started with MIUI 10 and Android 9, as expected by the rom with which I have done it and
then I have already installed MIUI 11 and then I have updated to Android 10, both with MiFlash20191206 of Xiaomi. To finish
installing the appropriate recovery, this time yes, and doing root
If you have disconnected the battery, open the phone as in photo 1 of the three that I attach.
Esto lo escribo para que lo use quien quiera siempre bajo su propia responsabilidad, no es complicado.
Una vez actualizado de rom Indonesia Miui 11 Android 9 a Android 10 e instalado un recovery de forma incorrecta y he vuelto a
bloquear mi Redmi Note 8 Pro (Begoña) y esta vez no he esperado a que se agote la batería como en la anterior (post #196)
sino que he usado el método del Test Point.
Esto es lo he hecho:
-Copiado la carpeta de la rom de Indonesia V10.4.2.0, una vez descomprimido el zip, en Equipo > C
-Instalado SP Flash Tool v5. 1924 Win también en C
-Desmontado la trasera del móvil y quitado la carcasa que hay por arriba de la batería (Foto 1).
-Preparado un trozo de cable fino de cobre, un estremo lo he conectado a un tornillo en la placa del móvil haciendo masa(Foto 2)
y al otro extremo le he conectado un clavo (Foto 4).luego he abierto el Flash Tool y he puesto el scatter que
hay en la carpeta "images" de la rom que que había copiado en C, y el DA y archivo de autentificación que hay en la propia
carpeta del Flash Tool y he conectado el cable usb al móvil, solo al móvil.
-He pulsado "Download Only" y he conectado el otro extremo del cable de cobre, preparado con un clavo, en el
punto Kcol0 (Foto 3) y he conectado el cable usb al ordenador. La barra de abajo del FlashTool ha empezado a rellenarse en
color rojo primero y luego cambia de color hasta que aparece el simbolo "Download Ok"
Lo he hecho con la batería desconectada (otros dicen que conectada) y con todo los archivos marcados en el
Flash Tool (otros dicen que sólo hay que marcar el preolader) y me ha funcionado.
Después de unos minutos se ha iniciado el móvil con MIUI 10 y Android 9, como era de esperar por la rom con la que lo he hecho y luego ya le he instalado
MIUI 11 y después he actualizado a Android 10, los dos con MiFlash20191206 de Xiaomi. Para terminar instalando el recovery
apropiado, esta vez sí, y haciendo root

javizeta said:
If you have disconnected the battery, open the phone as in photo 1 of the three that I attach.
The first time it crashed I revived it waiting for the battery to drain (post # 196) and now I have it back
to briquet when flashing wrong twrp and I have not waited for it to be exhausted again but I have done it
with a test point.
In photos two and three I show you where you have to connect the cable and privately I send you a link to an explanatory video
because I don't know if I can put links to youtube here.
It worked perfectly for me on the first try.
Click to expand...
Click to collapse
hey how to do me a favor pass the tutorial because I have the same problem:fingers-crossed:

maikiller said:
hey how to do me a favor pass the tutorial because I have the same problem:fingers-crossed:
Click to expand...
Click to collapse
I used the google search engine: tutorial to unbrick Chinese MTK phone and in the results I chose the Azlan Laion video.
Utilicé el buscador de google: tutorial desbrickear telefono MTK chino y en los resultados elegí el video de Azlan Laion.
Updated post # 2
Read please
Actualizado post #2
Leer, por favor

I definitely would appreciate anything that would get this flash to go through... I already have mine apart and have been trying everything to get it unbricked with no success as of yet...
Sent from my Redmi Note 8 Pro using XDA-Developers Legacy app

javizeta said:
I am writing this for anyone to use at their own risk, it is not complicated.
Once updated from Indonesia Miui 11 Android 9 rom to Android 10 and installed a recovery incorrectly and I have returned to
lock my Redmi Note 8 Pro (Begoña) and this time I have not waited for the battery to drain as in the previous one (post # 196)
I have used the Test Point method.
This is what I have done:
-Copied the folder from the Indonesian rom V10.4.2.0, once the zip is unzipped, in Computer> C
-Installed SP Flash Tool v5. 1924 Win also in C
-Removed the back of the mobile and removed the housing that is above the battery (Photo 1).
-Prepared a piece of fine copper wire, I have connected one end to a screw on the mobile plate making ground (Photo 2) and to
the other end I have connected a nail (Photo 4) .Then I have opened the Flash Tool and I have put the scatter that
*it is in the "images" folder of the rom that I had copied in C, and the DA and the authentication file that is in it
*Flash Tool folder and I have connected the usb cable to the mobile, only to the mobile.
-I pressed "Download Only" and connected the other end of the copper cable, prepared with a nail, in the
*point Kcol0 (Photo 3) and I have connected the usb cable to the computer. The bottom bar of the FlashTool has started to fill in
*color red first and then change color until the "Download Ok" symbol appears
*I have done it with the battery disconnected (others say it is connected) and with all the files marked on the
*Flash Tool (others say that you only have to mark the preolader) and it has worked for me.
*
After a few minutes the mobile has started with MIUI 10 and Android 9, as expected by the rom with which I have done it and
then I have already installed MIUI 11 and then I have updated to Android 10, both with MiFlash20191206 of Xiaomi. To finish
installing the appropriate recovery, this time yes, and doing root
If you have disconnected the battery, open the phone as in photo 1 of the three that I attach.
Esto lo escribo para que lo use quien quiera siempre bajo su propia responsabilidad, no es complicado.
Una vez actualizado de rom Indonesia Miui 11 Android 9 a Android 10 e instalado un recovery de forma incorrecta y he vuelto a
bloquear mi Redmi Note 8 Pro (Begoña) y esta vez no he esperado a que se agote la batería como en la anterior (post #196)
sino que he usado el método del Test Point.
Esto es lo he hecho:
-Copiado la carpeta de la rom de Indonesia V10.4.2.0, una vez descomprimido el zip, en Equipo > C
-Instalado SP Flash Tool v5. 1924 Win también en C
-Desmontado la trasera del móvil y quitado la carcasa que hay por arriba de la batería (Foto 1).
-Preparado un trozo de cable fino de cobre, un estremo lo he conectado a un tornillo en la placa del móvil haciendo masa(Foto 2)
y al otro extremo le he conectado un clavo (Foto 4).luego he abierto el Flash Tool y he puesto el scatter que
hay en la carpeta "images" de la rom que que había copiado en C, y el DA y archivo de autentificación que hay en la propia
carpeta del Flash Tool y he conectado el cable usb al móvil, solo al móvil.
-He pulsado "Download Only" y he conectado el otro extremo del cable de cobre, preparado con un clavo, en el
punto Kcol0 (Foto 3) y he conectado el cable usb al ordenador. La barra de abajo del FlashTool ha empezado a rellenarse en
color rojo primero y luego cambia de color hasta que aparece el simbolo "Download Ok"
Lo he hecho con la batería desconectada (otros dicen que conectada) y con todo los archivos marcados en el
Flash Tool (otros dicen que sólo hay que marcar el preolader) y me ha funcionado.
Después de unos minutos se ha iniciado el móvil con MIUI 10 y Android 9, como era de esperar por la rom con la que lo he hecho y luego ya le he instalado
MIUI 11 y después he actualizado a Android 10, los dos con MiFlash20191206 de Xiaomi. Para terminar instalando el recovery
apropiado, esta vez sí, y haciendo root
Click to expand...
Click to collapse
----------
Your method does not work because it depends on the motherboard you are using, for example the Mediatek uses another type of test point and they are blocked, I think that is why Xiaomi does not want to give more support to the Xiaomi Redmi Note 8 Pro (Begonia) as devices!
I have tried it several times and it does not work, the only thing is a working method is: Having the volume up pressed until the Mode Flash mode is activated and with the SP Flash Tool. The problem is that it asks for an Authorized Account and it is what I am looking for (of course to payment)
The Procedure
0. Unzip your device's firmware.
1. Install MiFlashPro.
2. Navigate to (installation_directory)/MiFlashPro/SP_Flash_Tool/mi and run "account_auth.exe" (Run as administrator). In the window that opens, log in with an authorized Xiaomi Account.
3. Navigate to (installation_directory)/MiFlashPro/SP_Flash_Tool nad run "flash_tool.exe". The SP_Flash_Tool interface opens. Now you have to select the 3 files:
Download-Agent: (installation_directory)/MiFlashPro/SP_Flash_Tool/MTK_AllInOne_DA_mt6765_mt6785.bin
Scatter-loading File: You will find this one on your stock rom folder, especially on the folder called "images".
Authentication File: (installation_directory)/MiFlashPro/SP_Flash_Tool/auth_sv5.auth
4. Press the "Download" button.
5. Connect the USB cable to your PC but NOT YET to your phone.
6. Hold the vol+ button on your phone pressed and NOW connect the cable to it.
7. The program should now react and start the flashing process without giving an error.
8. Wait for the flashing process to end and enjoy!

javizeta said:
I am writing this for anyone to use at their own risk, it is not complicated.
Once updated from Indonesia Miui 11 Android 9 rom to Android 10 and installed a recovery incorrectly and I have returned to
lock my Redmi Note 8 Pro (Begoña) and this time I have not waited for the battery to drain as in the previous one (post # 196)
I have used the Test Point method.
This is what I have done:
-Copied the folder from the Indonesian rom V10.4.2.0, once the zip is unzipped, in Computer> C
-Installed SP Flash Tool v5. 1924 Win also in C
-Removed the back of the mobile and removed the housing that is above the battery (Photo 1).
-Prepared a piece of fine copper wire, I have connected one end to a screw on the mobile plate making ground (Photo 2) and to
the other end I have connected a nail (Photo 4) .Then I have opened the Flash Tool and I have put the scatter that
*it is in the "images" folder of the rom that I had copied in C, and the DA and the authentication file that is in it
*Flash Tool folder and I have connected the usb cable to the mobile, only to the mobile.
-I pressed "Download Only" and connected the other end of the copper cable, prepared with a nail, in the
*point Kcol0 (Photo 3) and I have connected the usb cable to the computer. The bottom bar of the FlashTool has started to fill in
*color red first and then change color until the "Download Ok" symbol appears
*I have done it with the battery disconnected (others say it is connected) and with all the files marked on the
*Flash Tool (others say that you only have to mark the preolader) and it has worked for me.
*
After a few minutes the mobile has started with MIUI 10 and Android 9, as expected by the rom with which I have done it and
then I have already installed MIUI 11 and then I have updated to Android 10, both with MiFlash20191206 of Xiaomi. To finish
installing the appropriate recovery, this time yes, and doing root
If you have disconnected the battery, open the phone as in photo 1 of the three that I attach.
Esto lo escribo para que lo use quien quiera siempre bajo su propia responsabilidad, no es complicado.
Una vez actualizado de rom Indonesia Miui 11 Android 9 a Android 10 e instalado un recovery de forma incorrecta y he vuelto a
bloquear mi Redmi Note 8 Pro (Begoña) y esta vez no he esperado a que se agote la batería como en la anterior (post #196)
sino que he usado el método del Test Point.
Esto es lo he hecho:
-Copiado la carpeta de la rom de Indonesia V10.4.2.0, una vez descomprimido el zip, en Equipo > C
-Instalado SP Flash Tool v5. 1924 Win también en C
-Desmontado la trasera del móvil y quitado la carcasa que hay por arriba de la batería (Foto 1).
-Preparado un trozo de cable fino de cobre, un estremo lo he conectado a un tornillo en la placa del móvil haciendo masa(Foto 2)
y al otro extremo le he conectado un clavo (Foto 4).luego he abierto el Flash Tool y he puesto el scatter que
hay en la carpeta "images" de la rom que que había copiado en C, y el DA y archivo de autentificación que hay en la propia
carpeta del Flash Tool y he conectado el cable usb al móvil, solo al móvil.
-He pulsado "Download Only" y he conectado el otro extremo del cable de cobre, preparado con un clavo, en el
punto Kcol0 (Foto 3) y he conectado el cable usb al ordenador. La barra de abajo del FlashTool ha empezado a rellenarse en
color rojo primero y luego cambia de color hasta que aparece el simbolo "Download Ok"
Lo he hecho con la batería desconectada (otros dicen que conectada) y con todo los archivos marcados en el
Flash Tool (otros dicen que sólo hay que marcar el preolader) y me ha funcionado.
Después de unos minutos se ha iniciado el móvil con MIUI 10 y Android 9, como era de esperar por la rom con la que lo he hecho y luego ya le he instalado
MIUI 11 y después he actualizado a Android 10, los dos con MiFlash20191206 de Xiaomi. Para terminar instalando el recovery
apropiado, esta vez sí, y haciendo root
Click to expand...
Click to collapse
excuse me , could u wirte in english on these pictures , i can not read ur Lang, please,:highfive::highfive: please

gadmei.tw said:
excuse me , could u wirte in english on these pictures , i can not read ur Lang, please,:highfive::highfive: please
Click to expand...
Click to collapse
These are the texts included in the photos translated into English using the google translator
Photo 2: It is to this screw that I have attached one end of the cable
Photo 3: Upper label: To this round contact you have to connect the other end of the cable
Bottom epigraph: It is just above the battery connector. Battery disconnected.

javizeta said:
These are the texts included in the photos translated into English using the google translator
Photo 2: It is to this screw that I have attached one end of the cable
Photo 3: Upper label: To this round contact you have to connect the other end of the cable
Bottom epigraph: It is just above the battery connector. Battery disconnected.
Click to expand...
Click to collapse
thank u!
i will try through these point

need video please/necesito el video por favor
hi budy, how could you send me the video?, i got the same problem with my redmi note 8 pro
Hola amigo, espero que te encuentres bien, ¿Como podrías enviarme el video?, tengo el mismo problema con mi redmi note 8 pro, se apagó y no ha encendido

leandro iván said:
hi budy, how could you send me the video?, i got the same problem with my redmi note 8 pro
Hola amigo, espero que te encuentres bien, ¿Como podrías enviarme el video?, tengo el mismo problema con mi redmi note 8 pro, se apagó y no ha encendido
Click to expand...
Click to collapse
What video are you referring to?

Help google pixel 3a xl rom stock flash

I bought a google pixel 3a xl phone from amazon spain and this is what happened! when I turn on the phone it has an operating system totally unknown to me, I don't have google services, blocked bootloader, no usb debugging option, apparently it's from Verizon and I don't know what else to do, please help, I post photos and videos for you great help! the phone changed the storage slot from "b" (where the rom is) and "a" where there is nothing, thank you very much, thank you when turning on the phone apparently it is from the matrix
@michbenitez Telegram
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

While on slot_a try visiting this link using chrome browser. It's the latest android 11 factory image. Since you're bootloader locked you're not going to be able to flash anything that's not officially signed. If you have errors, make a note of the errors you receive and post them.

41rw4lk said:
Mientras esté en slot_a, intente visitar este enlace usando el navegador Chrome. Es la última imagen de fábrica de Android 11. Como el gestor de arranque está bloqueado, no podrá actualizar nada que no esté firmado oficialmente. Si tiene errores, tome nota de los errores que reciba y publíquelos.
Click to expand...
Click to collapse
The error I get is that the oem is blocked, no more errors appear, the equipment restarts again.

41rw4lk said:
While on slot_a try visiting this link using chrome browser. It's the latest android 11 factory image. Since you're bootloader locked you're not going to be able to flash anything that's not officially signed. If you have errors, make a note of the errors you receive and post them.
Click to expand...
Click to collapse
in slot_b is the corrupted rom it doesn't matter?

It does matter, but your main goal right now is to get stock flashed (if you can),then enable oem unlocking so you can unlocked your bootloader and get rid of whatever garbage rom that is. There is a thread around here for unlocking VZW bootloader.Try downloading this stock firmware (June patched android 11) and try flashing it yourself using the flash all. I'd try on slot_a first, hopefully that one is more recognized as stock.

41rw4lk said:
Sí importa, pero su objetivo principal en este momento es actualizar el stock (si puede), luego habilite el desbloqueo de oem para que pueda desbloquear su gestor de arranque y deshacerse de cualquier rom basura que sea. Hay un hilo por aquí para desbloquear el cargador de arranque VZW. Intente descargar este firmware de stock (Android 11 parcheado en junio) e intente actualizarlo usted mismo usando el flash all. Primero probaría slot_a, con suerte que uno sea más reconocido como stock.
Click to expand...
Click to collapse
41rw4lk said:
Sí importa, pero su objetivo principal en este momento es actualizar el stock (si puede), luego habilite el desbloqueo de oem para que pueda desbloquear su gestor de arranque y deshacerse de cualquier rom basura que sea. Hay un hilo por aquí para desbloquear el cargador de arranque VZW. Intente descargar este firmware de stock (Android 11 parcheado en junio) e intente actualizarlo usted mismo usando el flash all. Primero probaría slot_a, con suerte que uno sea más reconocido como st
Click to expand...
Click to collapse
41rw4lk said:
Sí importa, pero su objetivo principal en este momento es actualizar el stock (si puede), luego habilite el desbloqueo de oem para que pueda desbloquear su gestor de arranque y deshacerse de cualquier rom basura que sea. Hay un hilo por aquí para desbloquear el cargador de arranque VZW. Intente descargar este firmware de stock (Android 11 parcheado en junio) e intente actualizarlo usted mismo usando el flash all. Primero probaría slot_a, con suerte que uno sea más reconocido como stock.when i flash the rom i get an error flash.bar script on my computer screen, what do you think it could be? and on the adb screen it says: it is blocked
Click to expand...
Click to collapse
41rw4lk said:
It does matter, but your main goal right now is to get stock flashed (if you can),then enable oem unlocking so you can unlocked your bootloader and get rid of whatever garbage rom that is. There is a thread around here for unlocking VZW bootloader.Try downloading this stock firmware (June patched android 11) and try flashing it yourself using the flash all. I'd try on slot_a first, hopefully that one is more recognized as stock.
Click to expand...
Click to collapse
when i flash the rom i get an error flash.bar script on my computer screen, what do you think it could be? and on the adb screen it says: it is blocked

41rw4lk said:
It does matter, but your main goal right now is to get stock flashed (if you can),then enable oem unlocking so you can unlocked your bootloader and get rid of whatever garbage rom that is. There is a thread around here for unlocking VZW bootloader.Try downloading this stock firmware (June patched android 11) and try flashing it yourself using the flash all. I'd try on slot_a first, hopefully that one is more recognized as stock.
Click to expand...
Click to collapse
Could you help me by entering my pc?

No, I don't do remote desktop. Make sure you have the latest adb and fastboot installed. You can check the version you have installed easily. If you need the latest, you can grab them here. Also, if you could post the output of your cmd prompt that would help.

41rw4lk said:
No, no hago escritorio remoto. Asegúrese de tener instalados los últimos adb y fastboot. Puede comprobar la versión que ha instalado fácilmente. Si necesita lo último, puede obtenerlo aquí . Además, si pudiera publicar la salida de su indicador de cmd, eso ayudaríel código
Click to expand...
Click to collapse
41rw4lk said:
It does matter, but your main goal right now is to get stock flashed (if you can),then enable oem unlocking so you can unlocked your bootloader and get rid of whatever garbage rom that is. There is a thread around here for unlocking VZW bootloader.Try downloading this stock firmware (June patched android 11) and try flashing it yourself using the flash all. I'd try on slot_a first, hopefully that one is more recognized as stock.
Click to expand...
Click to collapse
I did everything as you told me but it keeps getting error bounces to bootloader

there is no way to unlock a verizon bootloader. you need to call amazon and request a refund. sometimes you can get lucky if you try to unlock before ever entering a sim card, but given the device was bought used, and can't boot to the system, that ship has long since set sail. this is a full brick. the only way out is to flash a factory image with fastboot, and that can't be done with a locked bootloader.

Well there is a way to unlock a VZW bootloader, I mean they did it to flash whatever garbage is on there. However I do agree, call Amazon and make them sort it. Basic troubleshooting hasn't and isn't going to fix this. As much as I like a challenge, this is just annoying. Call Amazon and tell them you bought someone else's **** up and move on from that mess.

sounds like what's on there is the stock verizon firmware, and the kernel just corrupted somehow. vzw is just an abbreviation for verizon wireless.
that, or like like said, they got lucky and unlocked before they put the sim card in, then relocked it before sending it out.
send it back. Amazon's return policy is too good to be dealing with stress like this.