Related
CWM is no more there after installing a new rom and new rom won't load. Then i have to flash the stock rom again > root it > install CWM. Again when i install any rom it would install normally but nothing gives a blank screen after reboot and the stock rom is not even there.
The situation is occurring with the following;
Phone: Sony Xperia ARC S (LT18i)
Bootloader: unlocked
Android version 2.3.4 (Build 4.0.2.A.42) -
I have made multiple attempts on installing new roms but nothing works. Every time i reboot after installation im left with a blank screen. Can anyone advise what the problem could be ?
Thanks
Did u flash the kernel for the ROM u flashed ? The ROM will not boot without its kernel.
Sent from my Xperia Arc S using Tapatalk 2
mtpocketz said:
CWM is no more there after installing a new rom and new rom won't load. Then i have to flash the stock rom again > root it > install CWM. Again when i install any rom it would install normally but nothing gives a blank screen after reboot and the stock rom is not even there.
The situation is occurring with the following;
Phone: Sony Xperia ARC S (LT18i)
Bootloader: unlocked
Android version 2.3.4 (Build 4.0.2.A.42) -
I have made multiple attempts on installing new roms but nothing works. Every time i reboot after installation im left with a blank screen. Can anyone advise what the problem could be ?
Thanks
Click to expand...
Click to collapse
you must be installing CWM into the system through one touch command prompt program.. as such as soon as the ROM changes and you wipe out data and cache, CWM disappears..try flashing a custom recovery kernel which are available even for stock roms.
Also follow these steps for a custom ROM (eg CM9):
download the ROM, extracted it into a folder, copy the boot.img where you can remember, then copy the original cm9 ZIP - not the extracted folder- into the root of SD..use fastboot mode of flashtools to flash the kernel boot.img which you had copied..its a recovery kernel so CWM should open..wipe out SD data..then cache..and then go into advanced option and clear dalvik..and then proceed to install zip from sd..then gapps.zip if u want..it should install fine..and then reboot.
Press Thanks if you think i was of help to you..:good:
Thanks
iwarind said:
you must be installing CWM into the system through one touch command prompt program.. as such as soon as the ROM changes and you wipe out data and cache, CWM disappears..try flashing a custom recovery kernel which are available even for stock roms.
Also follow these steps for a custom ROM (eg CM9):
download the ROM, extracted it into a folder, copy the boot.img where you can remember, then copy the original cm9 ZIP - not the extracted folder- into the root of SD..use fastboot mode of flashtools to flash the kernel boot.img which you had copied..its a recovery kernel so CWM should open..wipe out SD data..then cache..and then go into advanced option and clear dalvik..and then proceed to install zip from sd..then gapps.zip if u want..it should install fine..and then reboot.
Press Thanks if you think i was of help to you..:good:
Click to expand...
Click to collapse
Got it - Yes i was installing CWM within stock rom via market. though i tried to install it through adb/windows but still i guess the problem was all about not installing a custom recovery kernel.
Thanks a lot !
Installation aborted error status 7 xperia mini
I succesfully rooted my xperia mini and installed cyanogenmod 9 rc2 (smultron). The device was running fine with no problems then i did a huge mistake i entered in the cwm recovery and i formatted cache data syatem and all that listed there.then i reboot device it stuck on free xperia project logo.then i tried to install rom via cwm i started to give error installation aborted status 7 error. Please help no backup of official rom.
aditya naik said:
I succesfully rooted my xperia mini and installed cyanogenmod 9 rc2 (smultron). The device was running fine with no problems then i did a huge mistake i entered in the cwm recovery and i formatted cache data syatem and all that listed there.then i reboot device it stuck on free xperia project logo.then i tried to install rom via cwm i started to give error installation aborted status 7 error. Please help no backup of official rom.
Click to expand...
Click to collapse
Download stock ROM and install it via Flashtool.
My signature, there is link to download stock ROMs. Search for proper one and install it.
so whenever i download the "nightly builds" for d2tmo, i go into clockworkmod recovery.
after i clear the data,cache,etc, i get a error 7 installation aborted.
anyone help with that ?
Boot into your ROM again, download ROM manager, select the T-Mobile Galaxy S3 recovery, let it flash and install from the ROM Mananger app, select reboot into recovery from app the, should boot into recovery, flash CM10, enjoy.
hey its a recover-clockwork.img
how do i flash that ?
What exactly is an image file, the new recovery your flashing, or the version of cmx your trying to install. Have you changed any build.prop files. This could be telling your recovery that your ROM doesn't match the phone.
HazyJMac said:
What exactly is an image file, the new recovery your flashing, or the version of cmx your trying to install. Have you changed any build.prop files. This could be telling your recovery that your ROM doesn't match the phone.
Click to expand...
Click to collapse
i got it haha thanks !
Hi, I want to ask why I can't install DN3 v3 rom by using cwm philz 5.15
It's always show installation aborted or signature verification fail.
I from stock leak 4.3 N7100XXEMI6 without root
Here is my step to install this rom:
1. root through ordin
2. flash philz 5.15 recovery through ordin
3. full wipe including data, cache, dalvi cache
4. Fix permission
5. clear to install new rom
6. flash the DN3 v3 zip
*while installing zip file it always show installation aborted
*But if install other zip file everything go fine just have the problem on flashing custom rom
I was try many way but still get fail. hope some one can help me solve the problem.
updated 4.3official ane now wanna DN3 Rom v3.0
i just updated 4.3 official version :victory: but now i wanna DN3 Rom v3.0 :silly: so how can i flash give me detail for that
and ya do not update official 4.3 they dont give us any note 3 fetures ...:crying:
Issue flashing DN3 rom
Usually for flashing DN3 rom
1. root your device through ordin or stock recovery
2. flash cwm / twrp / phliz recovery
3. full wipe including data, cache, dalvi cache
4. fix permission
5. flash the DN3 rom (might need take some time)
6. Reboot
7. flash note 3 add on apps throught recovery
For my information is like that, but now i stuck on installing DN3 rom zip file while in philz recovery. always get installation aborted.
how to root in 4.3 official knox
yu133 said:
Usually for flashing DN3 rom
1. root your device through ordin or stock recovery
2. flash cwm / twrp / phliz recovery
3. full wipe including data, cache, dalvi cache
4. fix permission
5. flash the DN3 rom (might need take some time)
6. Reboot
7. flash note 3 add on apps throught recovery
For my information is like that, but now i stuck on installing DN3 rom zip file while in philz recovery. always get installation aborted.
Click to expand...
Click to collapse
but how to root ... installed 4.3 official version
patelsagar said:
i just updated 4.3 official version :victory: but now i wanna DN3 Rom v3.0 :silly: so how can i flash give me detail for that
and ya do not update official 4.3 they dont give us any note 3 fetures ...:crying:
Click to expand...
Click to collapse
it is easy to root ur phone just download these
CWM---- http://forum.xda-developers.com/showthread.php?t=1901196 [download the latest one with (.TAR) extension]
samsung usb drivers---google search for them
ODIN from here----http://forum.xda-developers.com/attachment.php?attachmentid=1168421&d=1341114315
now once u have all of the follow this video so that u can get every step
http://www.youtube.com/watch?list=UUA2XWPjQBJVScn7wQjeqMqA&feature=player_embedded&v=NFHZ535L7is
once ur done just update the superSU
thas for rooting need help to install the rom ask me:good:
Installing stopped at Page 1 of the Samsung apps
Hi there ppl,
I need some help.... i deleted everything, so now, my phone is romless.. n when i tried installing ditto note 3 (v3.1), the start up was ok, until u come to a page where u need to choose which apps you want to download.. i jus pressed next and it jus hanged there.. nothing was moving so i off and on my phone, and i tried again.. but yet, still cant install.. can anyone help... im frustrated here... hmmm....
BTW, i'm using the latest version of philz recovery, followed youtube link, and did exactly, but still... cant do much...
kalpeshneo said:
Hi there ppl,
I need some help.... i deleted everything, so now, my phone is romless.. n when i tried installing ditto note 3 (v3.1), the start up was ok, until u come to a page where u need to choose which apps you want to download.. i jus pressed next and it jus hanged there.. nothing was moving so i off and on my phone, and i tried again.. but yet, still cant install.. can anyone help... im frustrated here... hmmm....
BTW, i'm using the latest version of philz recovery, followed youtube link, and did exactly, but still... cant do much...
Click to expand...
Click to collapse
Just using previous philz touch recovery (Philz 5) and everything will works fine.
Using latest philz 6 will cause eror and hang (it happen to me too and it take a half day too realize the problem in the philz not the Rom )
yu133 said:
Hi, I want to ask why I can't install DN3 v3 rom by using cwm philz 5.15
It's always show installation aborted or signature verification fail.
I from stock leak 4.3 N7100XXEMI6 without root
Here is my step to install this rom:
1. root through ordin
2. flash philz 5.15 recovery through ordin
3. full wipe including data, cache, dalvi cache
4. Fix permission
5. clear to install new rom
6. flash the DN3 v3 zip
*while installing zip file it always show installation aborted
*But if install other zip file everything go fine just have the problem on flashing custom rom
I was try many way but still get fail. hope some one can help me solve the problem.
Click to expand...
Click to collapse
It sounds that you have a damaged file. Download the DN3 v3.1 ROM once it's complete verify its integrity using any MD5 checker tool.
kalpeshneo said:
Hi there ppl,
I need some help.... i deleted everything, so now, my phone is romless.. n when i tried installing ditto note 3 (v3.1), the start up was ok, until u come to a page where u need to choose which apps you want to download.. i jus pressed next and it jus hanged there.. nothing was moving so i off and on my phone, and i tried again.. but yet, still cant install.. can anyone help... im frustrated here... hmmm....
BTW, i'm using the latest version of philz recovery, followed youtube link, and did exactly, but still... cant do much...
Click to expand...
Click to collapse
Use Philz version 5.15, and clean all the data using Philz recovery. Do not select the option "Wipe Data" in the DN3 installer, this may cause your installation process to hang.
dvn2008 said:
It sounds that you have a damaged file. Download the DN3 v3.1 ROM once it's complete verify its integrity using any MD5 checker tool.
Use Philz version 5.15, and clean all the data using Philz recovery. Do not select the option "Wipe Data" in the DN3 installer, this may cause your installation process to hang.
Click to expand...
Click to collapse
Thanks guys for the help.. will download the philz 5.15 then and do it. anyways, ru guys having any problems with the ditto rom? does it hand when u multitask, etc?? coz i heard fr my frens that it hangs often...
appreciate your feedback guys. Thanks
ijsiregar said:
Just using previous philz touch recovery (Philz 5) and everything will works fine.
Using latest philz 6 will cause eror and hang (it happen to me too and it take a half day too realize the problem in the philz not the Rom )
Click to expand...
Click to collapse
I just signed up to say THANKYOU.... install Touchphilz 5!! it works than especially when you install DN3 v.3.1 or above!! thanks again!
Ditto Note 3 -> 3.2
DN3 rom work perfectly for me so far starting from v3 and now in v3.2.
I flashed DN3 rom in following sequence:-
(i) I came from MK4 Wanamlite previously and then I flash TWRP v2.6.0.3 via Odin
(ii) then I flashed MJ5 bootloader (downloaded from JoelDroid rom site) before installing DN3 rom
(iii)then I flashed DN3 v3 successfully.
With the DN3 v3.2 update, I tried dirty flash without wipe but hell lots of problems so finally I did full wipe, format data and then
clean install DN3 v3.2 anf all working perfectly so far including all the Note 3 features.
problem
hi
after i install dn3 ROM i can't make a call the imei is good but not registered to network
please help me
i got the same problem on 7105 Imei but no network, and stuck in factory mode, changing to on and running terminal script didnt help
i just updated 4.4.2 KK official version note 2 but now i wanna DN3 Rom without root..can i use DN3 rom feuture in my phn..
ota 3.2.1
Hi
I have one problem with OTA uppdate
I can't uppdate to 3.2.1
When I push uppdate , displays an error message
What is a problem?
yu133 said:
Usually for flashing DN3 rom
1. root your device through ordin or stock recovery
2. flash cwm / twrp / phliz recovery
3. full wipe including data, cache, dalvi cache
4. fix permission
5. flash the DN3 rom (might need take some time)
6. Reboot
7. flash note 3 add on apps throught recovery
For my information is like that, but now i stuck on installing DN3 rom zip file while in philz recovery. always get installation aborted.
Click to expand...
Click to collapse
Download the zip again and copy it on your sd card(maybe not copied well). This happens to me too
Hi Guys,
i am using samsung galaxy tab 3 sm-t210 model 7.0 wifi ..
i tried to flash the custom rom and followed the instruction in this forum http://forum.xda-developers.com/showthread.php?t=2754479
I have follwed the instructions from this forum http://forum.xda-developers.com/showthread.php?t=2437219 for an custom recovery and tried to flash the rom ...
when rebooted i am stuck up with an android screen for an hour..
later i downloaded the stock firm and flashed the firm with odin3.09 but now i am stuck up with samsung logo for an hour....
flashed twpr recovery and tried to install custom rom i am getting an E:/cannot mount /data error and i cam not able to flash any of the roms ,
experts please help me
Maybe it's a bad download or try flashing philz cmw then do clean install to flash a new rom then flash any rom
Brought to you by SM-T210R
Ripshock said:
Maybe it's a bad download or try flashing philz cmw then do clean install to flash a new rom then flash any rom
Brought to you by SM-T210R
Click to expand...
Click to collapse
tried now , getting same error
E: could not mount /data to setup /data/media path !
Please advice
brajesh0201 said:
tried now , getting same error
E: could not mount /data to setup /data/media path !
Please advice
Click to expand...
Click to collapse
Is your device rooted?
Brought to you by SM-T210R
Ripshock said:
Is your device rooted?
Brought to you by SM-T210R
Click to expand...
Click to collapse
yes rooted ,
brajesh0201 said:
yes rooted ,
Click to expand...
Click to collapse
Android-armeabi.universial-root.zip used this package to root
brajesh0201 said:
tried now , getting same error
E: could not mount /data to setup /data/media path !
Please advice
Click to expand...
Click to collapse
Have you make a backup befor you flashed The Rom?
For this Rom you need always The newest Recovery Version,depent of New updater script.
Can you go to The recovery , make a factory reset and wipe cache / dalvik.
Then go to download mode and flash Stockrom again.
Then flash Philz recovery, after flash Boot manuly into recovery make an backup and now reboot your Tab Into recovery make an fullwipe and flash your New Customrom.
bierma32 said:
Have you make a backup befor you flashed The Rom?
For this Rom you need always The newest Recovery Version,depent of New updater script.
Can you go to The recovery , make a factory reset and wipe cache / dalvik.
Then go to download mode and flash Stockrom again.
Then flash Philz recovery, after flash Boot manuly into recovery make an backup and now reboot your Tab Into recovery make an fullwipe and flash your New Customrom.
Click to expand...
Click to collapse
I tried the above method , no luck
if i flash stock firmware i stuck with an samsung logo and if i flash custom rom i stuck with an android boot image ...
i am not able to wipe in PhilZ recovery i am getting the error cannot mount /data and cannot mount /data/.androidsecure
brajesh0201 said:
I tried the above method , no luck
if i flash stock firmware i stuck with an samsung logo and if i flash custom rom i stuck with an android boot image ...
i am not able to wipe in PhilZ recovery i am getting the error cannot mount /data and cannot mount /data/.androidsecure
Click to expand...
Click to collapse
Im using philz tuoch and i habe no prob.
At philz have check The Mount point (sdcard or sdcard/0 )
If these all not hell flash CWM.
I have no clue what i did with it, but this is on the screen:
Odin Mode
Product name: SM-T210
Current Binary: Custom
System Status: Custon
HW REV: 0x5
It has an image like: Tablet......Yellow triagle with an ! in it.....Computer.
Under that it has the text: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. But Kies can't connect to the device. I have no clue what i did all ....
Experts please help !!!
hey
in philz recovery, in wipe options select - clean to install new rom
the goto tab 3 7.0 area get svelte rom , you need to put it on removable microsd with card reader [get one]
the put card back in tab reboot to recovery and flash, firmware updates aren't always good or necessary,
odin should be a last option. stay calm [use the force] and good luck :good:
brajesh0201 said:
Hi Guys,
i am using samsung galaxy tab 3 sm-t210 model 7.0 wifi ..
i tried to flash the custom rom and followed the instruction in this forum http://forum.xda-developers.com/showthread.php?t=2754479
I have follwed the instructions from this forum http://forum.xda-developers.com/showthread.php?t=2437219 for an custom recovery and tried to flash the rom ...
when rebooted i am stuck up with an android screen for an hour..
later i downloaded the stock firm and flashed the firm with odin3.09 but now i am stuck up with samsung logo for an hour....
flashed twpr recovery and tried to install custom rom i am getting an E:/cannot mount /data error and i cam not able to flash any of the roms ,
experts please help me
Click to expand...
Click to collapse
here is the solution of your prob, i font it in the lt02 Thread
bierma32
Post#352 and following Posts.
http://forum.xda-developers.com/showthread.php?p=53154386
Quote:
Originally Posted by*jstath1972*
In the first attempt i made a dalvik cache, cache, system wiping. I installed the rom and made again a dalvik cache, cache wiping and reboot. Then was saying "no Root. Would you like to flash super user in to system?" and then nothing. I made re install for second time the same rom zip with the default "Factory Reset" and everything went fine. Weird ha ? I also use TWRP 2.7.0.0 .*
I hope to help.*
Its funny its only work when you factory reset, My guess would be that something wrong with twrp or updater script.*
Maybe @gr8nole*will know more bout this issue.*
Sent from my Galaxy Nexus using Tapatalk
brajesh0201 said:
Hi Guys,
i am using samsung galaxy tab 3 sm-t210 model 7.0 wifi ..
i tried to flash the custom rom and followed the instruction in this forum http://forum.xda-developers.com/showthread.php?t=2754479
I have follwed the instructions from this forum http://forum.xda-developers.com/showthread.php?t=2437219 for an custom recovery and tried to flash the rom ...
when rebooted i am stuck up with an android screen for an hour..
later i downloaded the stock firm and flashed the firm with odin3.09 but now i am stuck up with samsung logo for an hour....
flashed twpr recovery and tried to install custom rom i am getting an E:/cannot mount /data error and i cam not able to flash any of the roms ,
experts please help me
Click to expand...
Click to collapse
try to flash the stock ROM Android 4.1.2 ( Jellybean ) from page www.sammobile.com and flash it with odin 3.07 , after you flash with odin sees the recovery of stock and give ' Wipe Data / Factory Reset ' ' and the problem is solved ( I run my me :good: ) and sorry for my bad English that use a translator :silly:
( and the solution suddenly discovered )
I just hope it works for you you too
Hi Guys,
This is my first time working with a custom ROM. I have an old S3 which sucks due to Samsung bloatware. So, I wanted to play and install Cyanogenmod on it.
I have a Rogers Samsung Galaxy S3 (Canada) and the model is SGH-I747M. I was following https://wiki.cyanogenmod.org/w/Install_CM_for_d2att to install the recovery image & Release build (https://download.cyanogenmod.org/?device=d2att&type=snapshot). I am using a Mac.
Steps I followed:
Installed Heimdall Suite on the Mac
Downloaded CM12 build & Google App and transferred it over to my phone's internal storage
Restared in download mode
Transferred recovery image
Restarted in recovery mode
Wiped/Factory settings
Apply Update -> cmbuild.zip file
It tried to install and then gave me a "Install Failed" error. I was then able to re-boot normally and get into the phone.
Any ideas, suggestions on what did I miss and what can I do? Is it ok to install the CM12 release build for my S3? Or do I need to go with CM11 or lower?
Thanks.
Flash twrp via heimdall to the s3. After flashing, boot into twrp and flash cm12.1 and gapps.
audit13 said:
Flash twrp via heimdall to the s3. After flashing, boot into twrp and flash cm12.1 and gapps.
Click to expand...
Click to collapse
Ok, so I tried what you suggested. I am still getting Install failed error.
The error says:
Can't install this package on top of incompatible data. Please try another package or run a factory reset.
E: Error executing updater binary in zip '/sdcard/d2att.zip'
UPDATE:
Fixed the problem by Formatting through TWRP and flashing CM12 & GApps again. Worked . Thanks for the help.
Glad you succeeded!