Develop Bugs

upgrading Falcon failed...I can't enter bootloader screen?

Deal all.
I have a cellphone, PW10C3 , FCC ID is NM8FALCON .
with ppc2003+cdma2000.
but I want upgrade to wm2003SE,or WM2005( maybe? )
I pressed the power button and reset, device display a screen " Serial HTC.....v1.06", no bootloader buttons, why?
How can I upgrade it by SD Card?
I can't upgrade by USB/Serial , report "communication error"...

Oh...My GOD
Why not anyone help me?
Falcon phone had dead at yestertoday....it can't power on ,can't recharge...
why? pls help me ...

Urgent Help Required Please>

Is This the correct section ?
I have a xda2 exec. I tried to update my rom, the congratulations screen displayed with a checking informaton on device message, this froze for some time so I disconnected the usb cable. when I tried to reset it, I get is a dispaly with just colours on it and it does nothing else, when I try to update again it shows an error connection error 101, also the device is not recognised. Is there a way to resolve this issue please and can someone be kind enought to direct me.
I used the rom update from - my-xda.com/xdaexec_soft2.html
Thank you in advance.

Try to hard reset your device
hold buttons: "-" + "-"
and then reset
so in practical terms, push the top 2 dash keys which are between your green and red phone icon buttons, and while holding them reset your device using the pen.
this should give you a white screen with a little menu.
You can now select clear device or something, I think it's the 0 or the X
it should work
if that doesn't work try to put your device in Bootloader
buttons: Backlight (front little button) + power button + reset button (with your pen)
again, hold the backlight and power button, then reset button
the screen should be dark, but if you look real close it would say USB or Serial v1.0 or v1.1 or something
you should be able to flash now using the tool
Also look around on this forum, loads of topics about upgrading/flashing and hanging problems
more info: http://forum.xda-developers.com/showthread.php?t=290234

u might have to update bootloader, try 2 read wiki.xda-developers.com lots of usefulll infos for beginers

Thank you
To both members above, thank you for your time. I am now using the update tool, hopefully this will now work. I used the method pressing the light button and power and reset. (Bootloader)

[Q] stuck at white screen at boot after flash

tried to flash RUU_RIO_U_APO_00_HTC_RUS_1.04.411.03_1.11b.3054.25_10.13.30_RETAIL_ENC_RELEASE and now the phone is dead.
it boots to the white screen with some barcodes and service info and that's all.
flashing process begins and reaches about 1% then the phone restarts and the flasher gives message about lost communication.
any suggestions what to do?
ps
is that the wrong ruu?
tried also RUU_RIO_U_APO_00_HTC_Europe_1.04.401.03_1.11b.3054.25_10.13.30_RETAIL_ENC_RELEASE but flasher said wrong vendor id and didn't proceed

ch1lko said:
tried to flash RUU_RIO_U_APO_00_HTC_RUS_1.04.411.03_1.11b.3054.25_10.13.30_RETAIL_ENC_RELEASE and now the phone is dead.
it boots to the white screen with some barcodes and service info and that's all.
flashing process begins and reaches about 1% then the phone restarts and the flasher gives message about lost communication.
any suggestions what to do?
ps
is that the wrong ruu?
tried also RUU_RIO_U_APO_00_HTC_Europe_1.04.401.03_1.11b.3054.25_10.13.30_RETAIL_ENC_RELEASE but flasher said wrong vendor id and didn't proceed
Click to expand...
Click to collapse
i think your phone is CID locked
1 question
i see in the screen shot on top security unlocked
is this a dev device or is this a brand new device ???
Switch the phone off.
Press and hold the VOLUME DOWN button, and then briefly press the POWER button. Release the VOLUME DOWN button when you see an icon on the screen.
Then press the following hardware buttons in sequence: VOLUME UP >VOLUME DOWN > POWER > VOLUME DOWN
Success!! Your phone is now reset to factory defaults.
if that does NOT work...maybe this ???
extract the NBH files from the RUU file
then hex edit your CID in it
if you open BOTH the nbh files there are HTC__xxx codes
in your screenshot i see that you have HTC__032
that code is NOT in both nbh files
so...
hexedit BOTH the NBH files and change HTC__001 to HTC__032
do this in both nbh files
then try to reflash
i DO not know if this works but you can give it a try
i am not responsable for any errors but as you broke your phone you can give it a try
can anybody else help this poor guy ???
good luck
m

megasounds said:
i think your phone is CID locked
1 question
i see in the screen shot on top security unlocked
is this a dev device or is this a brand new device ???
Switch the phone off.
Press and hold the VOLUME DOWN button, and then briefly press the POWER button. Release the VOLUME DOWN button when you see an icon on the screen.
Then press the following hardware buttons in sequence: VOLUME UP >VOLUME DOWN > POWER > VOLUME DOWN
Success!! Your phone is now reset to factory defaults.
if that does NOT work...maybe this ???
extract the NBH files from the RUU file
then hex edit your CID in it
if you open BOTH the nbh files there are HTC__xxx codes
in your screenshot i see that you have HTC__032
that code is NOT in both nbh files
so...
hexedit BOTH the NBH files and change HTC__001 to HTC__032
do this in both nbh files
then try to reflash
i DO not know if this works but you can give it a try
i am not responsable for any errors but as you broke your phone you can give it a try
can anybody else help this poor guy ???
good luck
m
Click to expand...
Click to collapse
i believe it's dev device because of the line not for sale on the boot screen with windows phone 8 logo
i can't switch the phone off because when i hold down the power button for 10 seconds it simply reboots and again shows that white screen. also i don't know whether the phone is charging in this mode because the led is off.

same here.
Security unlocked, CID_32.
after trying to flash goes strait to bootloader.
Please share European RUU, because all ROM's are gone from this forum. Or i can't find them

geduxaz said:
same here.
Security unlocked, CID_32.
after trying to flash goes strait to bootloader.
Please share European RUU, because all ROM's are gone from this forum. Or i can't find them
Click to expand...
Click to collapse
I I have the rom `s, but I could not change the cid to the cell, you could teach me how to do it, I have the phone in English and Chinese any more, and I need to put Spanish, thanks

[Q] i cant use phone. asking password(brand new phone)

when i swith on the phone a screen comes which aske me password. its is a new phone it this come without inserting the sim also.
does anyone know any solutions or can anyone tell me how to hard reset the phone?
and when i switch off the phone and press volume up + power key and when a menu appears and i choose recovery by pressing volume down key then a chines screen appears and after 2-3 min phone reboots.
and please don't type phone s fake Chinese. its brand new bought from amazon.in
please help

Contect amzon
So just contect amzon and tell ur problem and tell them to replace ur moblie... they will replace ur mobile... i guess so... contect them

Unlock the bootloader and flash cwm recovery. There are guides and tutorials in the development section of this forum, from recovery you can wipe data

please help my

my htc desire 300
Device only works on the HTC logo
I log to put bootloder , but did not open
All attempts failed when you press the play button to open bootloder
The device does not respond to pressure and responds to the rejection button
I can not login to put recovey mod To restore factory settings
When the device shows the word htc and shaking device 7 times and stay on this case
Please Almsaah Thank you very much ..

I had the same problem. In service told me it's crashed memory. Buy new phone or new motherboard from second hand phone

Thank you very much for your comment
You could use the device Riff box To install new bootloder ?