upgrading Falcon failed...I can't enter bootloader screen? - Upgrading, Modifying and Unlocking

Deal all.
I have a cellphone, PW10C3 , FCC ID is NM8FALCON .
with ppc2003+cdma2000.
but I want upgrade to wm2003SE,or WM2005( maybe? )
I pressed the power button and reset, device display a screen " Serial HTC.....v1.06", no bootloader buttons, why?
How can I upgrade it by SD Card?
I can't upgrade by USB/Serial , report "communication error"...

Oh...My GOD
Why not anyone help me?
Falcon phone had dead at yestertoday....it can't power on ,can't recharge...
why? pls help me ...

Related

I NEED HELP PLEASE _IMATE MW2003 SE_ EXPERTS HELP.

HI THERE, I WAS TRYING TO DOWNGRADE MY NEW I MATE AND SUDDENLY I GOT THIS MSG ON THE IMATE SCREEN "USB" ON THE TOP AND "V2. 06" WHILE THE IMATE IS ON THE CORDLESS. WHEN I TAKE IT OFF, IT DISPLAYS THIS MSG ON THE TOP" SERIAL" AND "V2. 06" AT THE BOTTON OF THE SCREEN . I WAS SICK OF THE CURRENT WORKING OPERATING SYSTEM AND TRYING TO DO SOME THING WITH IT.. HELP PLEASE
Do This first:
Press these 3 buttons at the same time:
Power button + Press the circle between the call answer and reject buttons + Soft Reset
Put the mobile into the cradel again and restart the (upgrade/downgrade) process.
which device do you have?
is it XDA2, XDA3 or?
if it shows 2.06 i suppose you have XDA3/Qtek909/pda2k.
right?
buzz

help me please

Can anyone help me out i was trying to downloading a new software upgrade for my mda pro and the computer froze on me no the phone is stuck with the screen saying with no light on serial at the top of it and at the bottom it say v2.01 but when i put the usb cable in or charge it it says usb on the screen instead of serial.The programme crash and now i cant ger out of that screen ive just told u about.I can do i hard restet and the light goes on saying press 0 to restore factory default and press x to exit.
When i press 0 it just goes back to the 1st screen i jst told u abt.With no light on and cant get light on or do anything with it.HELP i think when the update crashed on me it crashed the phone to and just kept on that screen with the serial on it.ACTIVE Sink will not work anymore when i put cable into the comptuer with my phone so updaing my phone agine will not work.Can anyone please point me in the right place to fix this promblem.Many thanx mono33
PS sorry it was so long winded but i needed to give you all the info possible i could give you.If there anything asle u need to know ust ask me and ill tell u what i can.Many thanx mono33
If this software upgrade was ROM upgrade, you're stuck in the Bootloader - check out the answers in the wiki and in the Universal Upgrading thread.
mono33 said:
Can anyone help me out i was trying to downloading a new software upgrade for my mda pro and the computer froze on me no the phone is stuck with the screen saying with no light on serial at the top of it and at the bottom it say v2.01 but when i put the usb cable in or charge it it says usb on the screen instead of serial.The programme crash and now i cant ger out of that screen ive just told u about.I can do i hard restet and the light goes on saying press 0 to restore factory default and press x to exit.
When i press 0 it just goes back to the 1st screen i jst told u abt.With no light on and cant get light on or do anything with it.HELP i think when the update crashed on me it crashed the phone to and just kept on that screen with the serial on it.ACTIVE Sink will not work anymore when i put cable into the comptuer with my phone so updaing my phone agine will not work.Can anyone please point me in the right place to fix this promblem.Many thanx mono33
PS sorry it was so long winded but i needed to give you all the info possible i could give you.If there anything asle u need to know ust ask me and ill tell u what i can.Many thanx mono33
Click to expand...
Click to collapse
If you have reached the bootloader mode and the word 'serial' changes to 'USB', you are in luck. Only before you connect to PC for upgrade open Active Sync on the PC and go to File / Connection Setting and UNCHECK 'allow USB connection' Checkbox. Then connect your device and follow the upgrade procedure. Actually you have posted this in the wrong forum. This should have been in the upgrade forum. Upgrade is not difficult. Please do let us know if you require any further help.

JAQ3 bootloader

Anyone knows how to put this device in bootloader mode??
and how to hard reset this device
thanks in advance
no nany help????
JAQ3 Bootloader
Hi to all please some body help I need to format my JAQ3 & enter Bootloader
boozer665 said:
Anyone knows how to put this device in bootloader mode??
and how to hard reset this device
thanks in advance
Click to expand...
Click to collapse
it can't be put on bootloader
you need a microsd card with less than 1 GB of size
then at laptop or desktop copy the .dip files from the rom (specific for JAQ3) in the root folder of the card
then turn off your jaq3 remove battery
put on microsd card
put on battery
press FN Key + Power on
Display will show up green and blue bars
after all bars complete
remove the battery and turn on the phone
that's all
regards!
jaq3
can sombody tell me where can i find the .dip files for my jaq3? ty
well the right way to hard reset this phone is not really like what mentioned in the previous reply but it s like what follows:
Turn off device, hold down send, end and camera buttons. Also press the power button then release all after on-screen prompt.

XDA Stealth no bootloader (cannot boot)

Dear all,
i've got 2nd hand xda stealth for 2 weeks, now my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram with nb0 extension on miniSD. please any one can help me to recover my Stealth ?
sorry for my bad english.
xda stealth..
go to www.seeo2.com, download a rom upgrade utility from there.. then start upgrade procedure again. As xda stealth is a hybrid phone..dont try any custom roms on it..
thank's malhar for responding my thread.
i already download the upgrade rom from the o2 site (now is www.mwg.com), i put the rom to my SDCard, the problem is how can i enter the boot loader, in case my stealth always in blank screen with call and end button are light.
i already press press power + call + end button, but my stealth stuck on that condition. every method of flashing mode i already try but no response from my stealth.
Syaipul
oh yea malhar, for information i read the procedure for upgrading on o2 site that connect status is required for upgrading procedure in activecync, my stealth has disconnected status when i plug to my com. can i do the upgrade the rom in this case?
buddy, remove ur sd card from the device first..and then hard reset ur device by pressing reset button via stylus, then flag which is windows home key and then ok key..reset+flag+ok.. maintain the sequence..press reset first keep on pressing then flag and ok key.. it will format ur device.... then try to flash new rom on it
ok malhar, i'll try tomorrow. thanks.....1000x
sad-sad-sad
my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram on miniSD. please any one can help me to recover my Stealth
Your SPL boot loader sounds like it is gone, formatted...
You may be able to patch it, using scripts & mtty if you can get into DL mode. Sounds like you're stuck in OEMSBL though.
help me !!!!
i have try pressing flat and ok botton to format . but nothing appear on the screen . is the other way to format or upgrade rom .
• The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
follow this thread from YUC wm6
http://forum.xda-developers.com/showthread.php?t=352468
blank screen
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
cant see o2 logo
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
randysng said:
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
Click to expand...
Click to collapse
Have you tried removing the battery for few hours ??? Does the engineering mode work???
engineering mode
engineering mode ? how to set engineering mode ?
randysng said:
engineering mode ? how to set engineering mode ?
Click to expand...
Click to collapse
How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
malhaar said:
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
Click to expand...
Click to collapse
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
khalifa_smart said:
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
Click to expand...
Click to collapse
It worked for me
Goto to your PDA setting and uncheck USB to PC.
Note: Check task before connecting to USB ensure no task including Active Sync.
FYI.
Im using VISTA Ultimate to update my XDA.
From WB 6.1 back to WM5. WM 6.1 too buggy and battery drained fast.
Cheers!
Please help me O2 stealth it dead not boot and blank screen .Are you Jtag for it please post it here.
i have the same problem --- my stealth is absolutely dead after using a cheap local charger
i have dismantled the board and taken some pics of the jtag connectors -- made the common LPT port jtag cable
how to proceed from here ?????
is the procedure similar to that of jtag recovery of a flame or an atom exec ??
how do i find the bootloader for O2 Stealth for flashing the NAND memomy Disk on Chip ??
please share your insights

[Q] i cant use phone. asking password(brand new phone)

when i swith on the phone a screen comes which aske me password. its is a new phone it this come without inserting the sim also.
does anyone know any solutions or can anyone tell me how to hard reset the phone?
and when i switch off the phone and press volume up + power key and when a menu appears and i choose recovery by pressing volume down key then a chines screen appears and after 2-3 min phone reboots.
and please don't type phone s fake Chinese. its brand new bought from amazon.in
please help
Contect amzon
So just contect amzon and tell ur problem and tell them to replace ur moblie... they will replace ur mobile... i guess so... contect them
Unlock the bootloader and flash cwm recovery. There are guides and tutorials in the development section of this forum, from recovery you can wipe data

Categories

Resources