Hey there,
I got this Desire Z from a friend as he was going to throw it away,
it does turn on, no notification light, screen doesnt turn on, no sounds but when i connect to my computer it shows up as Zeus Flash Device
Is the phone dead or is there any way to revive it?
im unsure what happened prior to it stopping working
any help appriciated
edit: found out its hard bricked, oh well lol
havokk said:
Hey there,
I got this Desire Z from a friend as he was going to throw it away,
it does turn on, no notification light, screen doesnt turn on, no sounds but when i connect to my computer it shows up as Zeus Flash Device
Is the phone dead or is there any way to revive it?
im unsure what happened prior to it stopping working
any help appriciated
edit: found out its hard bricked, oh well lol
Click to expand...
Click to collapse
Is this phone Rooted? well try this pull the battery out put it back in, and press and hold volume down button and press power and see if you are able to get into boot loader...
tricky !
two options
1- check bootloader (volume down + power) , if it gets a white screen with options , you can repair the device.
2- if it does not go into bootloader , then first download Htc sync for desire z , setup the android SDK , then plug ur phone inn, in command prompt , type *adb devices* .
If it shows a serial number below List Of Devices , then get back to this forum and report
And the last thing is the power Hardware button fine ?? Although quite impossible , but the hardware power button might be faulty !!
ahmedrzvi said:
Is this phone Rooted? well try this pull the battery out put it back in, and press and hold volume down button and press power and see if you are able to get into boot loader...
Click to expand...
Click to collapse
No response from anything lol
mohnish.killer said:
two options
1- check bootloader (volume down + power) , if it gets a white screen with options , you can repair the device.
2- if it does not go into bootloader , then first download Htc sync for desire z , setup the android SDK , then plug ur phone inn, in command prompt , type *adb devices* .
If it shows a serial number below List Of Devices , then get back to this forum and report
And the last thing is the power Hardware button fine ?? Although quite impossible , but the hardware power button might be faulty !!
Click to expand...
Click to collapse
Wasnt able to get into bootloader and nothing showing in abd lol
I unsinstalled and removed the driver that it was showing as when i plugged it in and now it lists itself as QHSUSB_DLOAD
After googling around it says this can be fixed with jtagging, and i know someone who does that so gonna let him take a look lol
And i know the power button is working as it doesnt show up in device manager untill i press it
!
as always JTAG FTW !!
Related
I have flashed many Custome ROM's before. I have HardSPL installed on my phone.
I tried flashing to a ROM (I forget which one now, I think Cloudfa or something) and it stopped at about 15%. The Update utility stopped as well.
I cannot connect to bootloader at all. I tried holding down on Volume down/Reset to enter bootloader, but the thing is that it's already in bootloader with the message "Upgrade ROM code error, Please try again"
ActiveSync doesn't see my phone either. In fact all it does is just sit on the bootloader screen with that error...
Please Help... Thanks You...
A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?
band27 said:
A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?
Click to expand...
Click to collapse
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...
jzalapski said:
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...
Click to expand...
Click to collapse
Have you tried flashing a different ROM while in bootloader?
^^ Yes. It give me an error on my computer...
I would like to try the internal flashing method but I don't seem to have a way of getting at my Storage Card.
I found this thread with a similar problem
http://forum.xda-developers.com/showthread.php?t=480022
I WAS just able to get off of that screen I was talking about, but the best I get is to the Touch Diamond Screen that lists my ROM and such. So no real progress.
I have a feeling that I would resolve my problem if I could Flash from the Interanl Storage...
Have you tried hard resetting the device?
Pull out stylus and Holding....1) Vol. Down 2) Center Round button 3) then press red button aka soft reset with stylus
Nothing...
im stuck
hi all i am very new to this im not sure what i have done or how to fix the problem i download these this morning and they worked
rom version 1.57.831.1(47324)wwe
radio version 1.14.25.24
protocol version 52.64.25.34u
when i bootload in tri colours screen it shows
BLAC100 32M
SPL-1.56.OliNex
MicroP-Blackstone (led)v6
if it shows that i must of done something right i think of what ill read
and i have windows 7 ulitmate and i have Miri_WM65_21815_V19.0_Premium
when i double click on the BLACKSTONE RUU WRAPPER it crashes then i rename a new folder and done it from there and it works but it comes up wit error 208 file open? then i got told to rename to ruu_signed.nbh file to blacimg.nbh and to store it in the root of my sd card done that then somehow i got it to come up to the screen by Turn off the phone, press and keep pressed volume down button and while keeping it pressed turn on the phone then i see a message "Press power to flash your device" and i press power to flash got to 0% and it crashed and come up with Upgrade ROM code error plz try again and stuck in bootloader mode but now it wont even turn on its dead it wont turn on no matter what i do can someone plz help
all i want to do is get windows mobile 6.5 working i cant understand that it can be so hard to do
thanxs blueboys25!
hi everybody,
i use http://forum.xda-developers.com/showthread.php?t=1259821 to root my htc desire hd, everything goes fine, it started to downgrade, some bars wre on the phone the phone rebootor some like that,then i must choose in hboot fast boot and so one ,the problem is if i want to choose with volume keys it doesnt work its like frozen,if i shutdown the phone it freeze at htc logo and that its, with volume - and power key i can start hboot,but then the keys doesnt work and i cant select any item, power key also doest work..any how to fix it? when i boot normaly and it freeze wtih connected usb my pc see it in device manager as usb storage but not more.
ty for help now
I do not get all of what u are saying, but if you can't move in hboot your problem is probably a bad sdcard. Try using a different one..
Sent from my GT-N7000 using xda app-developers app
m4rta said:
hi everybody,
i use http://forum.xda-developers.com/showthread.php?t=1259821 to root my htc desire hd, everything goes fine, it started to downgrade, some bars wre on the phone the phone rebootor some like that,then i must choose in hboot fast boot and so one ,the problem is if i want to choose with volume keys it doesnt work its like frozen,if i shutdown the phone it freeze at htc logo and that its, with volume - and power key i can start hboot,but then the keys doesnt work and i cant select any item, power key also doest work..any how to fix it? when i boot normaly and it freeze wtih connected usb my pc see it in device manager as usb storage but not more.
ty for help now
Click to expand...
Click to collapse
I think you will have to start again all process. Check if you have all USB driver installed ( if not, download HTC Sync from HTC site, install, reboot your system, then remove HTC Sync from your PC. JUST HTC Sync, not other diver wich have been installed ). After that process can be started. Check USB debugging and see if "charge only" is selected ( uncheck "ask me every time" ).
When the process start, choose 1 and let it to work. It will do everything without your help . When phone goes to hboot menu, you will see "volume up to ..bla bla...and volume down to ..bla bla. Only then hit once volume up. Now everything it shold be fine.
Ok i will try to explain what happend.
1. I done everthing like in instructunions,
2.Downgrade started copy files and so one, then it started all stuff in the phone some bares apears,extract stuff.
3. I must choose items with voluem keys it doesnt work, so i picked the first with power key.,everything goes fine.
4.hboot starts voluem keys doesnt work,power key also.cant even shut down with power key.
5.if i restart phone normaly, its freeze at htc logo
6. i if start phone with volume - and power key ,hboot appears but voluem keys doesnt work.
7.i plug usb ,start the phone with hboot , pc doest react ,like its not pluged in.
8 i plug usb start normaly, i see just in hardware manager an usb mass storage device,thats it i do not see in "my computer"
ok without sd card i cant navigate in hboot)
in hardware manager apears like android 1.0
with ace doest work,he do nto found phone,
what should i do now? for me is enough if i can just use my phone again -_-
Please get your volume button checked to make sure it's not damaged.
m4rta said:
ok without sd card i cant navigate in hboot)
in hardware manager apears like android 1.0
with ace doest work,he do nto found phone,
what should i do now? for me is enough if i can just use my phone again -_-
Click to expand...
Click to collapse
Uninstall the drivers and install them again with the phone unplugged...check what happens then. Have u installed anything else apart from running the Hack Kit?
Hi everybody.
first of all Ty all for checking out my post.
I have HTC ONE X Terga 3 (cid_K18) for the last 2 days i tried to find an answer to my problem without ant success to found right Q&A that fits to my problem i decided to open this help post.
3 days ago i rooted my HTC one x with hasoon2000 guide everything was good and i was happy and the day after i was driving to my work place using WAZE and also my phone were connected to car charger and suddenly my phone just crashed and wont turn one since.
few notes:
- no led at all
- i was and popup on my phone that saying something about "mksh" and i clicked allow
-tried to leave it one night with out charging
-tried to charge the phone with other charger
-tried power button for 10sec
-tried power button + vol down
nothing helped
hope u guys will can help me to find out this problem
When you said you tried power and vol down did u keep them pressed ? it should reset and take you to bootloader menu.
Maybe try different charger/usb cable?
NO TITLE
yeah i did what u said and just nothing
and no power led to any led at all
anyone? im really hopless
Hmm if you can't turn it on in any way there is not much we can do.
You can try this
Connect the phone to the pc and open a command window in the fasrboot folder and type
Adb reboot bootloader
And check if its recognized anywhere on the pc ?
wirth my the right cmd path for this pls
hmm you used the toolkit.....well drivers are installed then, check inside the folder of hassoons toolkit (or do a search in that folder) for the fastboot.exe file. hold shift down and click the right mouse button. select open command window here and type :
adb reboot bootloader
maybe it reacts
deivce not found...
i installed the drivres
but stil error
deivce not found...
Then there is not much i can do
dammit ok ty anyway
anyone else?
Hello,everyone,i got a problem that i cant enter fastboot and recovery mode.
today ,i installed CM12 22/7 upgrade ,and before i install this ,i did a backup of build.prop because i have V4A and every time i upgrade CM i have to change this build,prop ,so i want make a copy and when i finish upgrade i can just move that file without do anything ,and everything goes well, i installed upgrade and installed V4A driver ,it says i need restart,so i restarted,but after LG logo ,screen turn black, cant enter system ! i thought maybe i flash CM one more time can repair this,so i press POWER and volume down,but,nothing happen ,after LG logo,and screen turn black,and i try to enter fastboot mode ,its the same ,when LG logo shows screen turn black.......
My phone is LG d855,and my English is bad,i hope you can understand
Can anybody help me?
did you try entering Download mode?
Phone stuck in bootloop, help please
wrong trhead
Are you sure you there is no fastboot and no download mode?
You can enter download mode by pressing and holding the “Volume Up” and connecting the USB cable from phone to PC
If it works then you Soft bricked it...And you can use this guide to fix it:
http://forum.xda-developers.com/showthread.php?t=2785089
.
.
.
BUT if that does not work then you Hard bricked the phone
I had that problem because of flashing with faulty win8 drivers...no download mode or fastboot, all i got was security warning and bootloop. The only way you can fix hardbrick is through JTag, but i don't know if you can fix it without paying someone money, because you need special hardware to do it. You can find people on ebay that can fix it but it will cost you 30-50$.
I sent mine to warranty...they didn't know what was wrong with it and couldn't fix it...and so they just replaced the motherboard. If you have a warranty then send it and do NOT!! tell them you flashed it or rooted it. Tell them you don't know what happened...The chances of them finding out is very small.
If ebay and/or warranty not work, then there was an article on the Internet to fix a hard brick but for some reason it is now password protected...i do not know why....You can send the owner an email so he can give you the password.
http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants
...There is another article but it is in Portuguese
http://arena4g.com/forums/topic/tutorialunbrickhard-unbrickd855
But then again you cant be certain this will work either.
Conclusion: Fk LG...They don't want people upgrading their slow buggy software.
Alex_XV6700 said:
did you try entering Download mode?
Click to expand...
Click to collapse
i cant enter download mode,always turn black after LG logo
Disconnect cable from pc and phone
Press power + vol -
You will get first black screen, keep pressing until lg logo appears and it shuts off completely.
Then press just vol + and reconnect cable to computer.
That should leave you in download mode or fastboot.
Alex_XV6700 said:
Disconnect cable from pc and phone
Press power + vol -
You will get first black screen, keep pressing until lg logo appears and it shuts off completely.
Then press just vol + and reconnect cable to computer.
That should leave you in download mode or fastboot.
Click to expand...
Click to collapse
no,when i reconnect phone,and only press volume + ,its shows i am Charging then phone is off.......cant enter download mode,but i found when i press volume +and- , i can enter hardware key control mode,but there only have 3 choice,cancel , mode on and mode off,i have tried mode on and mode off,doesnt work.
rubisco1 said:
Are you sure you there is no fastboot and no download mode?
You can enter download mode by pressing and holding the “Volume Up” and connecting the USB cable from phone to PC
If it works then you Soft bricked it...And you can use this guide to fix it:
http://forum.xda-developers.com/showthread.php?t=2785089
.
.
.
BUT if that does not work then you Hard bricked the phone
I had that problem because of flashing with faulty win8 drivers...no download mode or fastboot, all i got was security warning and bootloop. The only way you can fix hardbrick is through JTag, but i don't know if you can fix it without paying someone money, because you need special hardware to do it. You can find people on ebay that can fix it but it will cost you 30-50$.
I sent mine to warranty...they didn't know what was wrong with it and couldn't fix it...and so they just replaced the motherboard. If you have a warranty then send it and do NOT!! tell them you flashed it or rooted it. Tell them you don't know what happened...The chances of them finding out is very small.
If ebay and/or warranty not work, then there was an article on the Internet to fix a hard brick but for some reason it is now password protected...i do not know why....You can send the owner an email so he can give you the password.
http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants
...There is another article but it is in Portuguese
http://arena4g.com/forums/topic/tutorialunbrickhard-unbrickd855
But then again you cant be certain this will work either.
Conclusion: Fk LG...They don't want people upgrading their slow buggy software.
Click to expand...
Click to collapse
thx for your reply. i tried many times with different way,try to enter download mode or fastboot .......but failed.and now i decided buy Nexus 6
hello
i searched the whole internet but there are not much informations about this Phone so i thought i make a new Thread
about the panasonic DCM-CM1 Factory Reset.
please write here any informations and experience you have about the Panasonic DMC-CM1
i never saw someone on youtube google or any other side or anyone who can tell me how to do a Factory Reset with this phone
today i called 5 Panasonic service numbers but noone can help, i also called about 10 Phone Service points for repair no one can help.
i tryed so much with this phone and i finaly found that the CM1 have a Secret key combination to connect it with USB as a Android ADB Interface without having acces to the phone cause it is screen locked.
1 .Turn Phone off
2. press Camera + Volume-up + Power ( Hold )
3. while Holding connect USB. (Hold)
4 .the LED should go green for maybe 2 seconds release all bottons while the led is green before it turns off and then the LED must still green.
then windows found a Android ADB Interface
if im in android SDK Tools i the phone will be found in fastboot!
if i type Fastboot Devices
the other thing i know is how to start in Save mode.
but this is nothing to help with a lost pin.. it only starts the phone without apps that have been installed by the user.
maybe for deinstalling a app or a buggy app.. dont know..
start phone at the screen for the pin or at the home menu..press the power botton hold for 2-4 seconds or so it ask for Shut down Restart and so.. just press and hold Shut down. and then it ask you if you want to start in Save mode. then press yes.
2 weeks ago i wanted to make a Screen lock with a pin for more secure.. i cant remeber the pin anymore thats why i want to make a Factory reset i think im not the only one. so any information would be nice
if there is someone who made Factory Reset with this phone or was able to start in fast boot or anything.. please share the infos with us!
thank you.