So.. I have installed new 4.1.2 via odin... After that i lost root.. Device status was normal.. I did autoroot, then triangle away.. Now my device status is Scanning...
|WTF ?
Related
So i saw the thread made by Doc few minutes ago and am having a dilemma right now...the QUESTION is if i use the root66 - PreRooted Firmware - T999_UVDLJA and FLASH a ROM for example [ROM][UVDLJA]~FrostyJB_4.1.1 the "Triangle" on the screen will appear or not?
"
and if i use the root66 - PreRooted Firmware - T999_UVALJ4 and flash a JB ROM the "Triangle" will not show up?
I have NEVER had the triangle even when my system says it is modified. Right now my phone is on the exact same thing i used odin with root66 then i flashed frosty. No triangle but my binary count is at one. With triangle away which i have used to test as far as i have been able to see it works fine so with the wonderful Triangle away i don't think their is any worry. If you do get the triangle just use triangle away.
Hi guys... Im trying to flash new polish firmware via Mobile odin...
Everything went good but when i got to that Android Figure on screen with Hypercube in belly and status bar, whenever status bar gets 1/3 full, phone resets itself...
Any one knows problem ?
Ok i discovered that there was something wrong with my cache.. So i pulled battery out, and flashed rom with odin (pc).
Now its booting
Stock MA6, successfully rooted, used triangle away to reset counter, and now when i check for ota updates it never stops.
What would you try?
R: [Q] OTA check taking infinite time
Holaaaaaa
Sent from my Galaxy Note 2 using Tapatalk 2
bcoz you have rooted device and sometime this happenes if samsung detects your device status modified.
Hi all. I have a Samsung Galaxy S4 Mini
I9195 since November 2013. I rooted it
about a year ago and installed CWM
recovery. I only had 3 apps that required
root; CPU Master, Samsung Log Converter
and Silent Boot. I was very happy with the
phone except for a problem with tabbed
browsing where I frequently couldn't close
open tabs as the tab button wouldn't work.
I eventually decided to update the software
hoping this would cure the problem. I knew
I would have to unroot the phone which
I did, and I did a back up to the external sd card
using CWM. Then I updated the software with
Kies on my pc. Well now I am running 4.4.2 and
it's terrible. The phone freezes, hangs, locks
up etc. So I tried to get back to 4.2.2 but I see this
isn't too easy. I tried to root the phone again with
Towel root and it says "Device Not Supported".
Then I ttird CF Root but Odin won't do it. I tried using the
CWM back up from the sf card via upload
mode and this had no effect. I have all the
correct drivers on the pc but Odin fails when I select
select the Serranotex file. When I connect the phone in download
mode the I.D Com box turns Blue not Yellow
Is it possible to completely erase the os
and re install 4.2.2? Also my Knox Counter shows 0x0
in recovery mode. Can I
root the phone via a file fom the external sd card?
Also I replaced the hdd in the pc a few months ago with an sdd.
Could this be part of the problem? Fortunately I had my trusty Galaxy
S2 handy as a spare phone. Sorry for the very long post
but its my first one. Any help would be greatly appreciated
0
Knox 0x0 you're lucky, try wiping factory reset in recovery.
Has your baseband changed?
I think you can downgrade to a one Brazilian 4.2.2 firmware which is Knox bootloader v2.
Rooting 4.4.2 official without triggering knox is tricky, early versions of kk you could use towellroot, ive read newer kk require flashing a early 4.4.2 kernel then use towelroot and flash again your original kernel kernel
Thanks for the reply fburgos . I managed to get it rooted by installing Odin and the drivers on another pc and it worked ok. I'm happy enough for now with my three root apps and Super user disabled Knox for me too.
I recently tried to initialize the firmware of my galaxy s3 running 4.4.2 to factory settings. But samsung Kies tried to install 4.1 into my phone and it bricked my device. It wasn't booting since then. So i tried to install something using odin according to a website and my phone started working properly. But now the issue is, when the phone is in download mode, it shows that the current binary is custom, the System status is Custom and the warranty bit is 1(in red color). I tried installing an app from google pay to check whether its rooted. and it says the phone is not rooted. Also i checked the phone by putting it in recovery mode, and it says its running android system recovey <3e>. So that seems fine too. But im confused why the phone is showing that the current binary is custom and also the system status is also custom while the phone is not rooted? Ive included a before (pic with three fail messages) and after screnshot of the download mode of my phone. Please help
Flashing non-stock software via Odin will cause this.
To reset everything, it is best to root, run triangle away, remove root. and it may go back to official.
The status may remain at custom since AT&T never released a full 4.4.2 ROM as KK was only available via OTA.