How to know if my phone can run JB? - HTC One X

Hello, I've already searched all around this forum but I've found many answers.
The version i have is from Asia.
Code:
[B]fastboot getvar version-main[/B]
version-main: 1.29.707.11
finished. total time: 0.006s
Code:
ENDEAVORU PVT SHIP S-ON RL
HBOOT-0.96.0000
CPLD-None
MICROP-None
RADIO-1.1204.105.14
eMMC-bootmode : disabled
CPU-bootmode : disabled
MODEM PATH : OFF
May 10 2012,01:32:07
CID_044 (something like this lol)
Click to expand...
Click to collapse
I flashed Paranoid once, but i want o try another JB roms. So, can i flash or not? Where's the updated list that i can see which cids can install JB?

You can flash an AOSP or CM jellybean ROM on any htc one X The only ones that are limited by CID are the Sense 4+ jellybean ones
So to make myself clear, generally you can flash any jb ROM as long as it doesn't have Sense
I hope this made it a bit more clear.
Sent from my HTC One X using xda premium

MUCH better! Thank you very much!
Where can i see the CIDs list that are available for update?

The Firmware supported CIDs are:
cidnum: HTC__001
cidnum: HTC__E11
cidnum: HTC__203
cidnum: HTC__102
cidnum: HTC__405
cidnum: HTC__Y13
cidnum: HTC__A07
cidnum: HTC__304
cidnum: HTC__M27
cidnum: HTC__032
cidnum: HTC__016
cidnum: HTC__J15
Sent from my HTC One X using xda premium
---------- Post added at 03:23 AM ---------- Previous post was at 03:19 AM ----------
And you can get your CID number by typing 'fastboot getvar cid' in fastboot
Also this thread might be useful: http://forum.xda-developers.com/showthread.php?t=1920060
Sent from my HTC One X using xda premium

But how do you it? Where did you find it? Is there any official website that shows which CIDs are able to upload the fb? lol

You remember how to use fastboot commands, right? on your Pc go to your fastboot folder, right click with your Mouse, and select open command prompt here. (or something like that) then boot your phone to bootloader and select fastboot. Plug the phone in,(should say fastboot USB at this point) and then type "fastboot getvar cid"
Sent from my HTC One X using xda premium

ontzaboy said:
You remember how to use fastboot commands, right? on your Pc go to your fastboot folder, right click with your Mouse, and select open command prompt here. (or something like that) then boot your phone to bootloader and select fastboot. Plug the phone in,(should say fastboot USB at this point) and then type "fastboot getvar cid"
Sent from my HTC One X using xda premium
Click to expand...
Click to collapse
Of course, but what i wanted to know where's the official list of this CIDs, like.... you get this list from HTC website? lol hmmm how can i say it lol
You showed me that CID list that can be updated. Where did you get this list? So i can check when mine can get the update

I'm not a dev so can't be 100% sure, but if I recall right it had something to do with the release keys being based on OTAs for Europe and certain countries of Asia
Sent from my HTC One X using xda premium

Hey guys sorry I'm kind of new to this aswell so excuse my ignorance but my device says 001 but not htc_001 instead its got my current carriers name telnz_001 does that mean it's not compatible????
Sent from my HTC One X using xda premium

LSTR said:
Hey guys sorry I'm kind of new to this aswell so excuse my ignorance but my device says 001 but not htc_001 instead its got my current carriers name telnz_001 does that mean it's not compatible????
Sent from my HTC One X using xda premium
Click to expand...
Click to collapse
has to be HTC_001 unfortunately!

The CID list can be taken directly from the released file.

BenPope said:
The CID list can be taken directly from the released file.
Click to expand...
Click to collapse
Thanks for clearing it out
Sent from my Nexus 7 using xda premium

BenPope said:
The CID list can be taken directly from the released file.
Click to expand...
Click to collapse
How? And the HBoot able to get the update, like:
"Hello you that got hboot version xxxx, the update is today!" lol

you cid is _044 as stated in the OP so you can't flash the JB Firmware and you won't be able to flash any JB rom till the official release will b out

Cruzaders said:
How? And the HBoot able to get the update, like:
"Hello you that got hboot version xxxx, the update is today!" lol
Click to expand...
Click to collapse
What?
Inside the update is a list of CIDs, I assume in some file that is also human readable. The list can't be changed because the whole thing is signed.
The phone sends a request to HTC over the internet, in that request it sends affair bit of info about the phone, including model number, CID and IMEI, the HTC server decides whether there is an update and responds appropriately.

I just installed Windows native due to doing web work (wanted Dreamweaver and photoshop native on my SSD computer for a bit, it's been linux/non windows for a while like all my computers, but wanted a Windows SSD setup not in a VM).
Interestingly, I get
C:\Users\waz\Downloads>fastboot.exe getvar cid
cid: None
finished. total time: 0.005s
C:\Users\waz\Downloads>fastboot getvar version-main
version-main: 1.28.862.9
finished. total time: 0.007s
*edit* SOLVED MYSELF
Not a windows expert, I've installed HTC sync, not sure if anything else. Anyone know why I can see a CID when I used fastboot in Linux but Windows says 'none' (And I can't remember the exact CID either, damn impaired memory from chronic pain + pain drugs)
Any help is appreciated, I found a few threads with people showing same 'nothing' but no fixes/workarounds.
*edit*
So, the next thing I check, I find it LOL
fastboot oem readcid

waz675 said:
I just installed Windows native due to doing web work (wanted Dreamweaver and photoshop native on my SSD computer for a bit, it's been linux/non windows for a while like all my computers, but wanted a Windows SSD setup not in a VM).
Interestingly, I get
C:\Users\waz\Downloads>fastboot.exe getvar cid
cid: None
finished. total time: 0.005s
C:\Users\waz\Downloads>fastboot getvar version-main
version-main: 1.28.862.9
finished. total time: 0.007s
*edit* SOLVED MYSELF
Not a windows expert, I've installed HTC sync, not sure if anything else. Anyone know why I can see a CID when I used fastboot in Linux but Windows says 'none' (And I can't remember the exact CID either, damn impaired memory from chronic pain + pain drugs)
Any help is appreciated, I found a few threads with people showing same 'nothing' but no fixes/workarounds.
*edit*
So, the next thing I check, I find it LOL
fastboot oem readcid
Click to expand...
Click to collapse
glad to see that there's someone who uses the search button

Related

[Q] after flash Revolution HD 10 my phone does not boot

I am having big trouble with my HTC One X
I am using for a long time Revolution and this morning I tried to make a update
Did everything what was printed here:
Did the boot 10.bat
Wiped data
Installed the zip Android_Revolution_HD-One_X_10.6.zip
After this nothing is happening even after 30 minutes waiting with the HTC Logo
Went to recovery but can't mount the USB message appears down: unable to open ums lunfile
What went wrong?
Is there a way to get into my memory card?
CID check
Unetwork said:
I am having big trouble with my HTC One X
I am using for a long time Revolution and this morning I tried to make a update
Did everything what was printed here:
Did the boot 10.bat
Wiped data
Installed the zip Android_Revolution_HD-One_X_10.6.zip
After this nothing is happening even after 30 minutes waiting with the HTC Logo
Went to recovery but can't mount the USB message appears down: unable to open ums lunfile
What went wrong?
Is there a way to get into my memory card?
Click to expand...
Click to collapse
Did you checked your CID
Firmware Supported CIDs:
cidnum: HTC__001
cidnum: HTC__E11
cidnum: HTC__203
cidnum: HTC__102
cidnum: HTC__405
cidnum: HTC__Y13
cidnum: HTC__A07
cidnum: HTC__304
cidnum: HTC__M27
cidnum: HTC__032
cidnum: HTC__016
cidnum: HTC__J15
Check your CID using this commend: 'fastboot oem readcid'.
If your CID is not in this list above, unfortunately you can't flash JB, stay with ICS for now.
And did you use super wipe?
sudhank said:
Did you checked your CID
Firmware Supported CIDs:
cidnum: HTC__001
cidnum: HTC__E11
cidnum: HTC__203
cidnum: HTC__102
cidnum: HTC__405
cidnum: HTC__Y13
cidnum: HTC__A07
cidnum: HTC__304
cidnum: HTC__M27
cidnum: HTC__032
cidnum: HTC__016
cidnum: HTC__J15
Check your CID using this commend: 'fastboot oem readcid'.
If your CID is not in this list above, unfortunately you can't flash JB, stay with ICS for now.
And did you use super wipe?
Click to expand...
Click to collapse
Sorry dont understand:
Firmware Supported CIDs:
cidnum: HTC__001
cidnum: HTC__E11
cidnum: HTC__203
cidnum: HTC__102
cidnum: HTC__405
cidnum: HTC__Y13
cidnum: HTC__A07
cidnum: HTC__304
cidnum: HTC__M27
cidnum: HTC__032
cidnum: HTC__016
cidnum: HTC__J15
How to check this?
And why my phone will not boot?
How can I get into my internal memory?
My HTC One X was working great before the update ( it was 9.4 Revolution HD)
I did the Super Wipe as I mentioned in my opening message
Please tell me how to proceed further?
edit I went to fastboot but nothing such as fastboot oem readcid
Please any body knows how to get into my internal memory?
I tried really everything I know of even tried the restore but I see the phone coming into boot mode, here the music..see the simcard and again it just reboots all the time
I am not a real expert so please some one to help me? I really need my phone, don't have a spare one here and on the road...
Thanks, Peter
Facepalm. Did you actually read through the post. Go into fastboot, then in cmd go to your fastboot folder and type fastboot oem readcid. Check if your cid is supported.
Sent from my HTC One X using xda app-developers app
I have the same situation!!!
How can I install another rom to my phone in order to make my phone usable again???????
I can't transfer any file from my computer to my phone now!!!!!
How this problem can be solved????
Help me please!!! Ican't use my phone now:crying:
XxVcVxX said:
Facepalm. Did you actually read through the post. Go into fastboot, then in cmd go to your fastboot folder and type fastboot oem readcid. Check if your cid is supported.
Sent from my HTC One X using xda app-developers app
Click to expand...
Click to collapse
Yes I did read it and sorry I am not so smart as you are, first of all I have very bad eyes and it takes some time even to login here
Could you again, or some one else tell me how to get back into any rom?
What I did, went to fastboot usb
Opened Win comander CMD
Typed: fastboot oem readcid
Reply from CMD not known command
Is there any software that can access my internal memory to upload another ROM?
EDIT I finally figure it out and I have HTC_032
So not supported so what next? Is my HTC bricked? Or is there a way to recover?
I just saw that my device is supported so why I can't boot?
HTC_032
Please members here please can you try to bring my HTC alive?
I really need the phone, went out to a open market here but no mobile with a mini sim card for sale
Can't wait until tomorrow need to call home
I just want to know how to flash any rom as I can't access my internal memory
Unetwork said:
I just saw that my device is supported so why I can't boot?
HTC_032
Please members here please can you try to bring my HTC alive?
I really need the phone, went out to a open market here but no mobile with a mini sim card for sale
Can't wait until tomorrow need to call home
I just want to know how to flash any rom as I can't access my internal memory
Click to expand...
Click to collapse
PLEASE some one to give me some ideas how to get any rom inside please guys any....
defensive said:
I have the same situation!!!
How can I install another rom to my phone in order to make my phone usable again???????
I can't transfer any file from my computer to my phone now!!!!!
How this problem can be solved????
Help me please!!! Ican't use my phone now:crying:
Click to expand...
Click to collapse
me too
i am already try about 3-4 times,but it's not work
now ,i just root it back to 9.7.2
You should be able unlock, flash clockworkmod 5.8.4.0, flash boot.img and then copy rom on using cwm, and flash it.
edwardiitii said:
me too
i am already try about 3-4 times,but it's not work
now ,i just root it back to 9.7.2
Click to expand...
Click to collapse
Can you please tell me how to do that???
I really tried every thing but dont know so much about the ONE X
I just want to flash my mobile back to any working ROM
BenPope said:
You should be able unlock, flash clockworkmod 5.8.4.0, flash boot.img and then copy rom on using cwm, and flash it.
Click to expand...
Click to collapse
But I don't know how to do that as I can't get into my internal memory
in fastboot usb it says that my phone is unlocked
Mate there's loads of guides on here. Might be worth just sticking to ICS for the meanwhile the bean is overrated. It'll get it easier to flash it eventually. Have you tried it the way Google intended yet?
Sent from my HTC One X using xda app-developers app
---------- Post added at 07:28 PM ---------- Previous post was at 07:26 PM ----------
In relation to the memory situation if your boot loaders unlocked. Use the HTC one x toolkit flash clockwork mod that way then you can mount the USB that method
Sent from my HTC One X using xda app-developers app
arknailed7754 said:
Mate there's loads of guides on here. Might be worth just sticking to ICS for the meanwhile the bean is overrated. It'll get it easier to flash it eventually. Have you tried it the way Google intended yet?
Sent from my HTC One X using xda app-developers app
---------- Post added at 07:28 PM ---------- Previous post was at 07:26 PM ----------
In relation to the memory situation if your boot loaders unlocked. Use the HTC one x toolkit flash clockwork mod that way then you can mount the USB that method
Sent from my HTC One X using xda app-developers app
Click to expand...
Click to collapse
Yes I tried Google but could not find it..
I have only sight at 1 eye and reading for a long time is very painful
But here a guy from the Hotel took my HTC hope it will work
Thanks any way
Unetwork said:
Yes I tried Google but could not find it..
I have only sight at 1 eye and reading for a long time is very painful
But here a guy from the Hotel took my HTC hope it will work
Thanks any way
Click to expand...
Click to collapse
All of the answers are here http://forum.xda-developers.com/showthread.php?t=1920060
Flash CWM and then in CWM, mount USB storage and copy.
Sent from my HTC One X using xda app-developers app
Hello guys,
I have the this problem too.
But as i can see my CID version Supported, i have HTC_304...
CWM can't mount USB..
Now What?
Thank you
grig05 said:
CWM can't mount USB..
Click to expand...
Click to collapse
Why? Do you have an old version? Install the latest.
BenPope said:
Why? Do you have an old version? Install the latest.
Click to expand...
Click to collapse
Thanks man!!!
CWM 5.8.4.0 was my solution!
Thanks again

PJ46DIAG Chinese Bought Diag File from SOFF guy

Hey guys, a friend in china soffed his device at a shop. And i asked him to buy the diag file for like 200 yuan, which is something along the likes for 40 bucks. However, he said it is pretty much useless without the white card or gold card. I went to the soff thread and saw that they tried the diag file. Not sure whether this is the same, but gotta try right? Please dont flame, if its the same diag file, then just ignore this thread, and it will be closed shortly
Waiting xmoo to put his hand and confirm it..
Sent from my HTC One X using Tapatalk 2
hoping if this one is the right diag file :angel:
same, cause in the thread xmoo said the chinese guy he talked to wont give it to him...but here i got this from a soff guy in a shop, so who knows. can someone notify him please
Sent from my HTC One X using Tapatalk 2
Same here, just waiting. I dont know how to make it work. Xmoo is an expert. :thumbup:
SKYDRAGON Team
S58 clean file is what's needed if I recall xmoo saying in another thread.
can you re upload the file ??
my device is saying that it is corrupted
Salbawardi2 said:
can you re upload the file ??
my device is saying that it is corrupted
Click to expand...
Click to collapse
Try opening it up on ur pc...:thumbup:
Sent from my HTC One X
Salbawardi2 said:
can you re upload the file ??
my device is saying that it is corrupted
Click to expand...
Click to collapse
Use 7zip.
So how to get it work with this? Y-Cabrl and Cardreader? And what to put in the cardreader? Should I have the Stock Kernel?
Sent from my HTC One X using xda app-developers app
guys, do not try if u dont know wat ur doing. the process should be short, my friend said it was done in less than a minute, and these were the files he used. however.the shop used a gold card to load the file, which costs 6000yuan with 100 access per card. making it 1000 dollars for us.
Sent from my HTC One X using Tapatalk 2
But, for my old Wildfire there was a prog to create a goldcard???
Sent from my HTC One X using xda app-developers app
DesmondderMondbär said:
But, for my old Wildfire there was a prog to create a goldcard???
Sent from my HTC One X using xda app-developers app
Click to expand...
Click to collapse
exactly what we are praying for to happen here
Sent from my HTC One X using Tapatalk 2
So, to resume: We have the diag, need a goldcard where to put the diag on, then we need a cardreader, in wich we put the goldcard. Then we connect the cardreader to an external powered usb Hub, an the, with an OTG Cabel to the HoX, right?
Sent from my HTC One X using xda app-developers app
DesmondderMondbär said:
So, to resume: We have the diag, need a goldcard where to put the diag on, then we need a cardreader, in wich we put the goldcard. Then we connect the cardreader to an external powered usb Hub, an the, with an OTG Cabel to the HoX, right?
Sent from my HTC One X using xda app-developers app
Click to expand...
Click to collapse
pretty much yes. that actually quite matches what my friend described
not too sure about the hub and stuff, but it is required to read a goldcard which is basically a micro sd
Sent from my HTC One X using Tapatalk 2
the (android-info.txt)
ModelID: PJ461****
CIDNUM: 11111111
MainVer: 0.06.0.0
Click to expand...
Click to collapse
so do we have to git super cid before we flash it ?
or just a gold card ?
I think it only means that its working with every cid
Sent from my HTC One X using xda app-developers app
[0.15.2000 ... T30S ... ENG ... HBOOT-T30S]
I am going to bet this is the clean diag : )
Product (endeavoru) = platform (HBOOT-T30S)
Anyone can confirm that this file seems for One X, by doing this "fastboot getvar all" and compare the values.
Now we only need the green light from Xmoo and some golden information from his side.
Only putting the diag on the virtual sdcard would be to easy, or? Or Flashing it via CWM?
Sent from my HTC One X using xda app-developers app
neuTrue said:
[0.15.2000 ... T30S ... ENG ... HBOOT-T30S]
I am going to bet this is the clean diag : )
Product (endeavoru) = platform (HBOOT-T30S)
Anyone can confirm that this file seems for One X, by doing this "fastboot getvar all" and compare the values.
Now we only need the green light from Xmoo and some golden information from his side.
Click to expand...
Click to collapse
Code:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Users\Anoop Anand>fastboot getvar all
INFOversion: 0.5a
INFOversion-bootloader: 1.12.0000
INFOversion-baseband: 2.1204.135.20
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 2.17.720.2
INFOserialno: *
INFOimei: *
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 3813mV
INFOdevpower: 44
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
all: Done!
finished. total time: 0.936s
C:\Users\Anoop Anand>
Iput a * in the serialno and imei fields
---------- Post added at 01:00 PM ---------- Previous post was at 12:59 PM ----------
But from what youve posted thas for an ENG hboot isnt it?? were SHIP

flash stock ruu on htc one x

After an OTA update my htc one x got into boot loop and the battery also stopped charging.
i charged the battery with the help of fashboot script and unlocked my boot loader and installed custom recovery. After that i charged my phone fully but still it is not starting. stuck at boot loop.
now i want to install stock ruu so please help to find the right ruu for my htc one x
CID-11111111
version-main-2.17.401.2
S-OFF
i tried to install /RUU_ENDEAVOR_U_JB_45_S_HTC_Europe_3.14.401.27_Radi o_5.1204.162.29_release_298897_signed.exe
this one but it gave an error "Error [159]:image error. choose the correct rom.
please help thanks in advance:crying:
You have S-OFF and SuperCid, so I think the RUU method should work, but maybe first change the CID to another like HTC__001 or HTC__E11 using command like in fastboot mode:
"fastboot oem writecid HTC__001"
Yep should work
Or flash the 1.39 hboot firmware and then the 3.14 ruu
Sent from my HTC One X using XDA Premium 4 mobile app
Mr Hofs said:
Yep should work
Or flash the 1.39 hboot firmware and then the 3.14 ruu
Sent from my HTC One X using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Mr Hofs thanks for your kind reply
i tried JB FW easy flasher tool. It changed my CID from 11111111 to HTC_621 and tried to flash firmware but it got stuck at sending 'zip' and phone remains at silver htc logo.
so far i tried to run RUU with my cid as 11111111
shall i try to run RUU after my cid changed to HTC_621
and i dont know how to upgrade hboot.
sir please guide
So your fastboot works......well download the 3.14.401 firmware zip file from the firmware placeholder thread (where you also posted in)
Rename the zip file to firmware.zip and flash it
Fastboot oem rebootRUU
Fastboot flash zip firmware.zip
This all needs to be done with a locked/relocked bootloader.
Sent from my HTC One X using XDA Premium 4 mobile app
[SOLVED] HTC stuck in boot loop after OTA update
Mr Hofs said:
So your fastboot works......well download the 3.14.401 firmware zip file from the firmware placeholder thread (where you also posted in)
Rename the zip file to firmware.zip and flash it
Fastboot oem rebootRUU
Fastboot flash zip firmware.zip
This all needs to be done with a locked/relocked bootloader.
Sent from my HTC One X using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Mr Hofs first of all thank you very much for your help.
here is my story. i bought HTC one x 10 days ago. i am not aware of initial CID, hboot etc. i bought it from Taiwan and presently i am in india.
After two days there was an OTA i got my phone updated and all the problems started. it got into bootloop. This is the time i look for help on XDA. I did factory reset but of no use. After some time i realized battery is also not charging. Every time i plug the phone to pc or wall charger it starts automatically and gets into bootloop. With the help of XDA i found the fastboot script for charging the battery. After that i unlocked my phone and flashed the CWM recovery and got battery charged.
It is the time i came know about
UNLOCKED
S-OFF
version-main-2.17.401.2
Hboot-1.12.0000
CID-11111111
But the problem of not booting up still persisting.
i downloaded and tried
1. RUU_ENDEAVOR_U_JB_45_S_HTC_Europe_3.14.401.31_R_Radio_5.1204.162.29_release_302015_signed_2
2. ruu_endeavor_u_jb_45_s_htc_europe_3.14.401.27_radio_5.1204.162.29_release_298897_signed
3. RUU_ENDEAVOR_U_JB_45_S_hTC_Asia_TW_3.14.709.20_Radio_5.1204.162.29_release_292865_signed_2
and
4. RUU_ENDEAVOR_U_ICS_40_S_HTC_Europe_2.17.401.2_Radio_2.1204.135.20_release_274900_signed_2
first three RUU stuck at sending file and after 10 minutes or so gave error [159]:image error
The fourth one installed successfully without giving any error but the phone was still in bootloop.
I tried custom rom cyanogenmod 10.1 but it didnt install, it required higher version of Hboot.
Tried MIUI rom it got installed but the touch screen not working.
After that as you suggested i tried to update the firmware 3.14.401. The link you gave was not working may be temporarily. But it was already there on my pc. I didnt flashed it earlier because i was not sure whether this was correct firmware for my phone.
A week passed in above mentioned research.
Today i flashed the firmware and it gave and error with the message to flash it again immediately. So again i run the command but noting happened. so after 15 minutes i removed the phone from pc and restarted it and there it was Hboot-1.39.
So i tried the RUU no. 3 (mentioned above). This time it stuck at erasing user data for about 30 minutes so again i removed the phone from pc.
After that i installed cyanogenmod 10.1 nightly.
Now the phone is working put some features are not working like camer. i think this may be the fault of rom..
Sir should i flash the firmware again?
What i do know to go back to stock or custom rom fully functional and similar to stock.
Well anyway i had lost the hope and with your kind support i made is of some use. Thanks again
Try any other sense based rom, all roms should work on that hboot (1.39) even all sense 5 roms.
So try SD rom, or viper x 4....just to name a few....or arhd, doesn't matter wich one actually. Just try one and get back
Sent from my HTC One X using XDA Premium 4 mobile app
Mr Hofs said:
Try any other sense based rom, all roms should work on that hboot (1.39) even all sense 5 roms.
So try SD rom, or viper x 4....just to name a few....or arhd, doesn't matter wich one actually. Just try one and get back
Sent from my HTC One X using XDA Premium 4 mobile app
Click to expand...
Click to collapse
So there is no need of flashing the firmware again?
poonforce said:
So there is no need of flashing the firmware again?
Click to expand...
Click to collapse
Nope !
Sent from my HTC One X using XDA Premium 4 mobile app
Mr Hofs said:
Nope !
Sent from my HTC One X using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Sir now the camera is not working. when i switch on the camera it displays distorted static colors instead of image, its totally garbled.
and in SD rom the even after inserting the sim there is no network.
whereas in cyanogenmod network was there. only the camera was having the same problem.
and sometimes there is error "command write failed" using fastboot commands
And sir sometimes commands does not works. It hangs at sending .... even in ruu also it stuck at erasing data, sometime at rebooting to bootloader and sometime at sending... dont know what is happening .
And after flashing firmware 3.14. when i boot into boot loader there is one thing which comes in red for around one second or so.. "[preload] Failed to open usb mass storage" something like that..
dont know how to fix it.
poonforce said:
Sir now the camera not working in any custom rom. when i switch on the camera it displays the multicolor bars.
and in SD rom the even after inserting the sim there is no network.
whereas in cyanogenmod network was there. only the camera was having the same problem.
and sometimes there is error "command write failed" using fastboot commands
And sir sometimes commands does not works. It hangs at sending .... even in ruu also it stuck at erasing data, sometime at rebooting to bootloader and sometime at sending... dont know what is happening .
And after flashing firmware 3.14. when i boot into boot loader there is one thing which comes in red for around one second or so.. "[preload] Failed to open usb mass storage" something like that..
dont know how to fix it.
Click to expand...
Click to collapse
Run the command fastboot oem writecid HTC__032 and run RUU 3.14.401.27 and report what will happend
Thant said:
Run the command fastboot oem writecid HTC__032 and run RUU 3.14.401.27 and report what will happend
Click to expand...
Click to collapse
it gave an error "write failed invalid cid"
Try to use a USB 2.0 port (no USB 3.0)
You could try to disable virusscannersoftware
Download the stock recovery and boot.img from a 3.14.401.31 and flash them via fastboot firmware 3.14.401.31
Write CID to HTC__E11
Relock your bootloader
Flash a RUU via PC (execute .exe file) download RUU. I recommend a re-download, cause you had img error before.
webpatrick said:
Try to use a USB 2.0 port (no USB 3.0)
You could try to disable virusscannersoftware
Download the stock recovery and boot.img from a 3.14.401.31 and flash them via fastboot firmware 3.14.401.31
Write CID to HTC__E11
Relock your bootloader
Flash a RUU via PC (execute .exe file) download RUU. I recommend a re-download, cause you had img error before.
Click to expand...
Click to collapse
Sir i am using windows8 and not able to extract recovery and boot image from the RUU 3.14.401.31. any idea how to extract on windows.
The firmware is a zip file open it with 7zip and copy the boot.img and recovery from it and flash it
And btw, flashing boot and recovery files has to be done with a UNLOCKED bootloader, installing ruu files and flashing firmware files has to be done with a LOCKED/RELOCKED bootloader !
sent from my .......
Thanks to XDA and all the members who helped me in repairing my HTC ONE X.
continuing from last post.
As suggested by Webpatrick i installed stock recovery and boot image extracted from firmware 3.14.401.31.
tried to change my cid to HTC_E11 but it gave an error. i could change my cid to HTC_621 only.
so after done above i tried to install ruu http://htc.vi8.info/hTC-One-X/RUU_E...Radio_5.1204.162.29_release_302015_signed.exe
It gave cid error. So i changed my cid back to Supercid and again run the said RUU.
This time it flashed my HOX successfully. now i have stock rom.
Soon i will post the nandroid backup of my phone hoping it will help somebody like me..
once again thanks to all.
poonforce said:
Thanks to XDA and all the members who helped me in repairing my HTC ONE X.
continuing from last post.
As suggested by Webpatrick i installed stock recovery and boot image extracted from firmware 3.14.401.31.
tried to change my cid to HTC_E11 but it gave an error. i could change my cid to HTC_621 only.
so after done above i tried to install ruu http://htc.vi8.info/hTC-One-X/RUU_E...Radio_5.1204.162.29_release_302015_signed.exe
It gave cid error. So i changed my cid back to Supercid and again run the said RUU.
This time it flashed my HOX successfully. now i have stock rom.
Soon i will post the nandroid backup of my phone hoping it will help somebody like me..
once again thanks to all.
Click to expand...
Click to collapse
Good for you!
Thanks for this latest update, it could help some people. Everybody should give such a detailed update after success, but many forget!
Unable to flsh with ruu
version: 0.5a
version-bootloader: 1.36.0000
version-baseband: 5.1204.162.29
version-cpld: None
version-microp: None
version-main: 3.14.720.24
serialno: HT245W121191
imei: 35918XXX1XXX301
product: endeavoru
platform: HBOOT-T30S
modelid: PJ461XX00
cidnum: HTC__038
battery-status: low
battery-voltage: 2854mV
devpower: 0
partition-layout: None
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: None
hbootpreupdate: 2
gencheckpt: 0
Can Any one suggest me which Ruu should i boot for this device i have tried falsshing
RUU_ENDEAVOR_U_ICS_40_hTC_Asia_India_1.26.720.2_Radio_1.1204.90.13_release_251419_signed ---> its showing 140 Boot vershion error please help me ASAP my phone is not booting into os as well please let me know thanks in advance
lico1021 said:
This is assuming you didnt completely brick your phone which, was my situation. also assuming you can still access your start menu:
click start>settings> on the bottom next to Personal tab, select System.
now select Clear Storage(the icon should be a garbage can with files going into it)
I believe it prompts you to give it the okay. I dont remember if it told me i was going to lose all saved applications and contacts, BUT yeah I did lose all that stuff. That was more than fine considering my phone was ****ED! No apps would open there were errors all over the place and I couldnt get it to flash. Anyway, it hard resets, you see the att screen and it literally goes thru the whole customization setup you went thru when you first turned it on. THATS A GOOD SIGN! haha. it works perfectly.
CONCLUSION: This simple way put my phone right back to its original ATT settings down to the very last piece of crap, lol. BUT i was MOREEE than happy to see it. From there I was able to flash HardSPL(ROM that allows flashing of any other ROM your heart desires)...and the rest is history!
Hope this helps.
Click to expand...
Click to collapse
Answered you in another thread where you posted this. Do not spam this all over and wait at one place to get a responce. We have otherwise no idea where to answer anymore !
poonforce said:
Sir i am using windows8 and not able to extract recovery and boot image from the RUU 3.14.401.31. any idea how to extract on windows.
Click to expand...
Click to collapse
firmware link broken bro send fix it bro
cid: HTC__038
finished. total time: 0.106s
E:\htc\Fastboot HTC\Fastboot HTC\Fastboot HTC>fastboot getvar all
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.72.0000
(bootloader) version-baseband: 3.1204.171.33
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 2.18.707.6
(bootloader) serialno: FA356W100083
(bootloader) imei: 353XXXXXXXXXX
(bootloader) product: enrc2b_u
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PM3511000
(bootloader) cidnum: HTC__038
(bootloader) battery-status: good
(bootloader) battery-voltage: 3877mV
(bootloader) devpower: 58
(bootloader) partition-layout: None
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.478s
WILL DA ROM WORK IN THIS?

[Q] How to know the good RUU

Hello Everybody,
My bootload is locked I have tried to run one RUU I got the error 155 I think maybe I got the wrong RUU for my phone here are the specification:
Hello everyone
I have no idea what is the good RUU for my device I have a HTC one:
INFOversion: 0.5a
INFOversion-bootloader: 1.73.0000
INFOversion-baseband: 5.1204.167.31
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 4.19.707.3
INFOserialno: XXXXX
INFOimei: XXXXX
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: HTC__044
INFObattery-status: low
INFObattery-voltage: 3162mV
INFOdevpower: 0
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
Please can anybody send me the link for the good RUU.
Thank you.
You are in the wrong forum mate !
This is the international One X forum and not the One. !!
Sent from my HTC One X using XDA Premium 4 mobile app
teonagode said:
You are in the wrong forum mate !
This is the international One X forum and not the One. !!
Sent from my HTC One X using XDA Premium 4 mobile app
Click to expand...
Click to collapse
lol he has the one x if you look in his log from getvar all then you see it's the hox
at OP
there is no good or bad RUU ...but for your CID and mainversion doesn't exist such a high RUU version ...no CID does have such a high RUU version...you can only use a nandroid backup...but please don't ask for guides...there are enough where you can look yourself
And since you are locked you should have warranty if something is wrong !
Mr Hofs said:
And since you are locked you should have warranty if something is wrong !
Click to expand...
Click to collapse
haha didn't saw that his bootloader is locked...
yes like Mr Hofs said...if you have problems with your phone send in...your bootloader is locked so they will fix all issues...
One-X-master said:
haha didn't saw that his bootloader is locked...
yes like Mr Hofs said...if you have problems with your phone send in...your bootloader is locked so they will fix all issues...
Click to expand...
Click to collapse
i did not either but he said in the OP that his bootloader is locked and not relocked :laugh:
Mr Hofs said:
i did not either but he said in the OP that his bootloader is locked and not relocked :laugh:
Click to expand...
Click to collapse
yea i didn't even read that
One-X-master said:
lol he has the one x if you look in his log from getvar all then you see it's the hox
at OP
there is no good or bad RUU ...but for your CID and mainversion doesn't exist such a high RUU version ...no CID does have such a high RUU version...you can only use a nandroid backup...but please don't ask for guides...there are enough where you can look yourself
Click to expand...
Click to collapse
Ok I find a post on XDA about stock nandroid when i write the command:
C:\Users\xxxx\Desktop\HTC One X>fastboot flash boot boot.emmc.win
error: cannot load 'boot.emmc.win'
What should I do?
mano775 said:
Ok I find a post on XDA about stock nandroid when i write the command:
C:\Users\xxxx\Desktop\HTC One X>fastboot flash boot boot.emmc.win
error: cannot load 'boot.emmc.win'
What should I do?
Click to expand...
Click to collapse
First off all if your bootloader is locked you can't flash anything, second is that when it can't load the file it has or the wrong name or it is not in the fastboot folder !
Long hair ,beautiful eyes , ass like beyonce ,that's thing to look for a good RUU
Sent from my HTC One X+ using xda premium

Variant System Version OTA Update Error

After a long wait I finally got my ota update to Nougat.
But there is another problem, I cant finish the update because my phone showed that error.
I'm on stock M9 in bootloader it says software status official, locked, and s-on. No root, as I have checked it using root checker. Recovery is there.
I never modified my phone. And its fine back when I updated from lollipop to mm via ota, there is no problem.
And as far as I know, my phone is on correct mid and cid, SKU 708, mid 0PJA10000 exactly the same with mid engraved on my phone, and cid HTC__044
But when I update mm to nougat, this variant system version error shows up
I have tried to flash RUU of my current firmware, but still nothing.
Please help me, where did I do wrong? or how can I solve this problem?
Bumping this because I got the same thing too.
My device is not even rooted!
Did you guys flash a RUU for your current firmware and try to download the OTA, again?
Flippy498 said:
Did you guys flash a RUU for your current firmware and try to download the OTA, again?
Click to expand...
Click to collapse
I did, but the problem stays there.
Flippy498 said:
Did you guys flash a RUU for your current firmware and try to download the OTA, again?
Click to expand...
Click to collapse
I dont know how to flash the RUU.
But anyway, is there a way to check whether i can flash the OTA on my own?
vglaksana said:
I did, but the problem stays there.
Click to expand...
Click to collapse
Can you please copy and paste the fastboot getvar all output here (without your IMEI!)? It might help us to help you.
-marco- said:
I dont know how to flash the RUU.
Click to expand...
Click to collapse
Well, there is a thread pinned above all the other threads in this section that is even called "ReadMe" and people still tend to completely ignore it...
-marco- said:
But anyway, is there a way to check whether i can flash the OTA on my own?
Click to expand...
Click to collapse
If you can't flash an OTA via the software update function then you can't flash it via fastboot, either. Your phone doesn't pass the security checks that google implemented with android 5 so the method you use for flashing the OTA doesn't matter.
Flash a RUU and re-try to install the OTA. If that still doesn't matter then please copy and paste your fastboot getvar all output here (without your IMEI!), as well.
Flippy498 said:
Can you please copy and paste the fastboot getvar all output here (without your IMEI!)? It might help us to help you.
Click to expand...
Click to collapse
Here it is
C:\Users\Vito G. Laksana\Desktop\New folder>fastboot getvar all
(bootloader) kernel: lk
(bootloader) product: htc_himauhl
(bootloader) version: 1.0
(bootloader) imei:
(bootloader) version-main: 3.42.708.3
(bootloader) boot-mode: download
(bootloader) version-baseband: 01.01_U114,10801_97.64.60111G_F
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 0PJA10000
(bootloader) cid: HTC 044
all: inished. total time: 0.016s
Above is getvar all from before I flashed my current RUU. I believe it wouldn't change anything, as I can't get fastboot getvar all working now.
vglaksana said:
(bootloader) cid: HTC 044
Click to expand...
Click to collapse
If that is an exact copy of the output then it's no miracle that you can't install the OTA. That CID doesn't exist. It needs to be HTC__044 (8 letters, numbers or symbols in total and no spaces). You need S-OFF for being able to correct your CID.
Sent from my HTC One M9 using XDA Labs
Flippy498 said:
If that is an exact copy of the output then it's no miracle that you can't install the OTA. That CID doesn't exist. It needs to be HTC__044 (8 letters, numbers or symbols in total and no spaces). You need S-OFF for being able to correct your CID.
Sent from my HTC One M9 using XDA Labs
Click to expand...
Click to collapse
Ah my bad. The correct CID is HTC__044, as I mentioned in the thread first post.
I just using image to text converter because I have screencap of the output and didn't see that straight away.
Ah ok. And I already hoped that we found the cause of the problem... There have been some threads about devices that got bought in the US, S-OFFed and reflashed to non-US versions for selling them in other countries, in the past (around the time when firmware 2.x was the latest one). In most cases the sellers didn't convert the phones correctly and the buyers faced similar errors to your one when they tried to install an OTA.
Unfortunately there's nothing strange I can find in that output, then.
Sent from my HTC One M9 using XDA Labs
Flippy498 said:
Ah ok. And I already hoped that we found the cause of the problem... There have been some threads about devices that got bought in the US, S-OFFed and reflashed to non-US versions for selling them in other countries, in the past (around the time when firmware 2.x was the latest one). In most cases the sellers didn't convert the phones correctly and the buyers faced similar errors to your one when they tried to install an OTA.
Unfortunately there's nothing strange I can find in that output, then.
Sent from my HTC One M9 using XDA Labs
Click to expand...
Click to collapse
Thanks for helping me figuring out the problem.
If that is the problem, then why I have successfully update from lollipop to mm?
Yes i did buy it second hand, he said that the phone is from Singapore, and from the getvar output it is make sense that my phone came from Singapore.
Soo...I believe my only option is to S-OFF and convert to other version to get the update, is that correct?
I just re-read your opening post. Looks like I missed the part with the engraving. The US variant has a different engraving than the one you mentioned. So my assumption is probably wrong.
Since I have no clue what might cause your problem I actually don't see any other solution than getting S-OFF and converting the phone.
If there was a publicly available 4.x RUU for your SKU you could have asked Sneakyghost whether he creates a firmware package for you. By flashing that (S-OFF needed) you would have been able to use the 4.x RUU although you never installed the corresponding OTA. This way you could have kept your SKU. However, I haven't seen a public download link for such a RUU, yet. Therefore, you'll need to convert to a different SKU if you want the latest firmware.
Since you're still on firmware 3.x you need to flash one of Sneakyghost's 4.x packages before you can flash a 4.x RUU of the SKU that you want to convert to. Or you use a 3.x RUU for converting and try to install the OTA of the new SKU, afterwards. (The latter will probably take longer in total.)
Alternatively, you can wait some more days and see if some else has a better idea.
Sent from my HTC One M9 using XDA Labs
Flippy498 said:
Can you please copy and paste the fastboot getvar all output here (without your IMEI!)? It might help us to help you.
Click to expand...
Click to collapse
I rebooted into bootloader to get the getvar but it doesnt work.
adb lists no devices.
Also, see the enclosed pic. that's as far as i managed to get.
Adb won't work if the device isn't booted to system or recovery mode.
And since the fastboot mode doesn't exist anymore on the M9 and all newer HTC phones you need to boot to download mode.
Sent from my HTC One M9 using XDA Labs
Flippy498 said:
Adb won't work if the device isn't booted to system or recovery mode.
And since the fastboot mode doesn't exist anymore on the M9 and all newer HTC phones you need to boot to download mode.
Sent from my HTC One M9 using XDA Labs
Click to expand...
Click to collapse
booted to system: adb sees device but says it's offline
booted to dl mode: adb can't see the device.
anyway, i took picture of what dl mode looks like. Attached.
Yeah, that's how it's supposed to be. ADB can only be used if the phone is booted to the system or the recovery mode. You can't use ADB commands while it's booted to the bootloader or the download mode. You need to use fastboot commands in these modes.
Sent from my HTC One M9 using XDA Labs
Flippy498 said:
Yeah, that's how it's supposed to be. ADB can only be used if the phone is booted to the system or the recovery mode. You can't use ADB commands while it's booted to the bootloader or the download mode. You need to use fastboot commands in these modes.
Sent from my HTC One M9 using XDA Labs
Click to expand...
Click to collapse
apparently i had a problem with drivers. i have fixed it now, that's why it gave empty devices.
Ok went back to bootloader mode. run fastboot getvar all:
Code:
(bootloader) version:0.5
(bootloader) variant:MTP eMMC
(bootloader) secure:yes
(bootloader) version-baseband:
(bootloader) version-bootloader:
(bootloader) max-download-size: 0x20000000
(bootloader) partition-type:cache:ext4
(bootloader) partition-size:cache: 0x14000000
(bootloader) partition-type:userdata:ext4
(bootloader) partition-size:userdata: 0x5e0000000
(bootloader) partition-type:system:ext4
(bootloader) partition-size:system: 0x118000000
(bootloader) serialno:HT54GYJ05021
all:
finished. total time: 0.132s
this is instead the same taken from dl mode:
Code:
(bootloader) kernel: lk
(bootloader) product: htc_himauhl
(bootloader) version: 1.0
(bootloader) version-main: 3.42.708.3
(bootloader) boot-mode: download
(bootloader) version-baseband: 01.01_U11440801_97.04.60111G_F
(bootloader) version-bootloader: 1.0.0.0000
(bootloader) mid: 0PJA10000
(bootloader) cid: HTC__044
all:
finished. total time: 0.006s
what now?
Mhm, there's nothing strange in that output, either.
Can you flash a RUU and re-try installing the OTA? If that doesn't fix the problem then the only other option is converting the phone as I already suggested to vglaksana.
Sent from my HTC One M9 using XDA Labs
Flippy498 said:
Can you flash a RUU and re-try installing the OTA?
Click to expand...
Click to collapse
can you point me to a guide on how to do this?
and also where can i find my relevant RUU?
thanks.
I already did so in my first reply to you.
Sent from my HTC One M9 using XDA Labs

Categories

Resources