Hello everyone
I just bought a Galaxy Nexus last week and I am so far very satisfied with it.
But I do have one problem with the build quality.
At the front top, with the speakerphone and front facing camera, the plastic seems a bit loose, I can push it inward a bit and it will creak.
If I will push it inward with some force it will stay there solidly for a bit, but after a while it while go out again. I'd think it should remain flush with the case in any case. I check the screws under the battery cover already, and everything there seems to be fine, nothing is loose, so I have no other idea what might cause that.
Is this a common issue, or does anyone else here have this problem? Anyone know a possible fix?
I heard about this problem when I bought my GN (it was last year in December). It is the adhesive which is supposed to keep the glass and the LCD beneath together that fails to do its job. I recommend you bringing the phone back to the store from where you bought it for a replacement. That's what I would do.
Do you have any source of that?
I did not read anything like that yet.
And I don't think that is really the problem, the screen and glass seems to be well connected, it's that it separates from the casing.
Related
I was wondering if anyone else had some backcover flexing. Specifically, right between the camera and the google logo. This is with the standard cover with 1750mhA battery.
It just bothers me a bit because its not perfect. :S
I definitely have some flexing there and for me, if I press my finger to the right of the camera (looking at the back) it flexes and makes a slight clicking noise. Bothers me too and I end up doing it on purpose way too much >< My friend works at the place I bought it and she let me try another back to see if it made a difference but it did the same thing so I think it's normal!
It's good to know that it's not just my phone experiencing this. Thanks of the reply.
Mine doesn't flex at all!
mine does, and the one i replaced did as well, i expect the 3rd one does the same so i didnt go back to exchange it
same to 3 of my frd's
so, if u dont like it, put 2 layers of scrotch tape on the inside of the battery cover around the camera area
Well, I got my Nexus on thursday, but immediately I noticed a problem .
At the bottom, the glass is slightly tilted, on the right is raised above the frame, while on the left is recessed ...
these are some pictures I took
I talked to the shop and they told me that they will solve the problem (repositioning of the glass) ...
What I wanted to know is what happen when the phone is opened, because on my current Nexus One, after first service, i have tons of dust entering between the display and the glass, and obviously I don't want the same thing also on this phone
So, do you have some experience with samsung's assistance ?
thanks!
anyone ?
As long as it's purely cosmetic, I wouldn't risk (or waste the money) having some guy open the phone to even out the glass.
Mine is the exact same way at the top of the screen, and I only noticed mine a few weeks after having it just because I was looking very very closely at the screen.
However, the problem it's quite visible on my phone, the difference between the two corners is about 1 mm, and with the glass that protrudes from the frame is even more subject to scratching ...
I don't know what to do ...
there is no one who opened the phone ?
The what you call a "glass" is the whole screen, so there no any way you get dust particles under it, as there no "under" , maybe the glue that hold it not have not dry good, I remember SGS2 have some yellow tint, or maybe it was SGS1, anyway things like that do happen to some devices.
Are you sure?
I have always found that touchscreen ("glass") and the display are two separate things
I'd return it for a replacement, that's an obvious build defect cite that you fear it'll either get worse or become a leak source.
Also, I am relieved I don't have this issue although I'd expect that I'd notice it quickly as you
Hello there!
I bought my xperia m 10 days ago, and i am pleased so far, except for one thing..
I noticed yesterday that the removable cover has started creaking, especially on the side with no buttons where the usb port is.
Has anyone else noticed that with their device? Is this something that inevitably happens after a while, or should i try to get it replaced because of a defect?
Yes, it started happening a few days after I bought or... If it happens to others too, I'll assume it's inevitable
This message was brought to you from my Sony Xperia M C1905 using Tapatalk.
Hmm I see..
Well I thought I'd ask because if it is something that is going to happen anyway, i will not bother taking it to the store.
They will have to send the phone to the service center and all that fuss just to replace the back cover, so it is not worth it.
If someone else can also confirm that this is the case with their phone I will be assured.
My phone also makes noises when pushed, most at top right and bottom left corners.
Well I take it there is nothing I can do about it then, so no point in returning it, I will have to live with it...
It is a shame though, because other than that the phone is outstanding in terms of value, I see no reason to spend any more that what I spent on this. It hits the sweet spot for me in the price/performance scale.
Has anyone found any solution to this problem?
I have tried putting little pieces of paper at the hotspots (bottom left and below the usb port in my case) but I had little success...
I am also curious to hear reports from others, maybe a silicon case can lessen the issue...
Cassius Away said:
Has anyone found any solution to this problem?
I have tried putting little pieces of paper at the hotspots (bottom left and below the usb port in my case) but I had little success...
I am also curious to hear reports from others, maybe a silicon case can lessen the issue...
Click to expand...
Click to collapse
I have silicone case, it is the same. I am thinking about using thin layer of hotglue. It can be peeled of easily.
After some experimenting I found that putting a small piece of paper (3mm tall and about 3cm long) between the phone and the cover eliminated the major creaks that where in the lower-middle left side of my phone. I just folded a piece of printer paper in two and cut it to the above dimensions. If you try it make sure to put it in a way that does not block the small plastic clips that clip on the phone.
Just under the volume button is popping out. After about a month or so thinking it was the case - I just put on a Samsung stock case and I believed it was not attached to the phone. Turns out, today I was looking a little deeper and the glass screen is bowing up from the bottom. Another words, you can push with your thumb on the back cover and it will bulge up while the frame stays. Never been dropped or even hardly carried.
Anyone else seen or heard of this?
Nobody had any issues of the glass pushing up in the middle left side of the phone under the volume button. I might as well play the lotto then......or not.
Ok, looks like my battery is a bit swollen and may have caused it??? Anyone else notice anything?
Mines been fine
I have had mine since last November, It has been in an Otterbox for the better part of six months, I have not noticed anything like you are describing.
My phone is awesome. So is it's condition.
I've had this phone for about three weeks and after around two weeks, I noticed that the pictures were starting to come out fuzzy and overexposed looking. Finally realized that there was dust under the glass covering the camera lens. Unfortunately, since it's under the glass, I'd have to take it apart to clean it (or possibly send it to Amazon for warranty, if they cover it).
The issue is that even if I take it apart and clean it, the issue will come up again and I'd rather not have to constantly take it apart and clean (especially since it happened only after two weeks). Does anyone have any suggestion to prevent this from happening again, besides not keeping it in my pocket?
This seems like a poor quality design to me. I carried my previous phone in my pocket for four years without any issues.
Thanks.
I also seem to have this problem. I need to look up how to open my fire phone, because my pictures aren't focusing well anymore. I now have a phone case, so I hope dust will stop going under the lens.
I got the same issue, and I actually send my phone for replacement. That being said, before sending it I took a compressed air can with the tiny tiny applicator and sprayed inside the microfone on the back and and the gap in the bezel, it blew away everything inside blocking the camera. I suspect there is a defect where there is too much gap on either the microphone and the back or the bezel and the back, so I just returned it anyways. If I had no warranty, that's what I would do, just be gentle with that microphone or it will die, the compressed air released at full throttle will break that microphone.
I had the same problem (is quite common), but it's easy to fix if you have a little bit of manual skills. Just buy a torx t3 screwdriver and a suction cup, open the phone, clean the glass in front of the camera and close. 5 minutes of work.
If you search on ifixit there's a fire phone teardown that explain how to open it. Simple and fast.
I got mine replaced from Amazon.
Called Amazon, but they said that since I bought it from eBay, it's not covered under warranty. Considering I had the phone for only a few weeks, you'd think they'd support their own product. Ah well.
Initially I wanted to avoid opening up the phone, as to not void the warranty, but as it turns out, it's not covered anyway.
I've followed the iFixIt video and cleaned out the lens. So, it's good as new; however, this isn't something I want to be doing on a regular basis. Does anyone have any suggestions for keeping the dust out, besides not keeping it in my pocket?
Thanks.
ashram said:
Called Amazon, but they said that since I bought it from eBay, it's not covered under warranty. Considering I had the phone for only a few weeks, you'd think they'd support their own product. Ah well.
Initially I wanted to avoid opening up the phone, as to not void the warranty, but as it turns out, it's not covered anyway.
I've followed the iFixIt video and cleaned out the lens. So, it's good as new; however, this isn't something I want to be doing on a regular basis. Does anyone have any suggestions for keeping the dust out, besides not keeping it in my pocket?
Thanks.
Click to expand...
Click to collapse
Unfortunately there's not much that can be done about this AFAIK. As stated above, there is a design flaw where the microphone on the back let's in the dust, so unless you cover it, you'll end up needed to clean it every once in a while. But I've also noticed not too much distortion in the photos.
iFixit has a great pictures and guides for dismantling the fire phone. This is what I used to open mine up to clean the camera glass. Note it is well worth cleaning the lens as the camera auto focus works much faster when clean.
https://www.ifixit.com/Device/Amazon_Fire_Phone
I have to clean my camera every month.
I think I should buy a new phone right now.
stunvn said:
I have to clean my camera every month.
I think I should buy a new phone right now.
Click to expand...
Click to collapse
I do the same every other month. Very annoying. At least with the right screwdriver and a suction cup is pretty fast and easy to open and clean it.
Next time I open mine to clean, I am going to try an remedy the issue by adding a foam washer (or my DIY version of double sided sticky foam tape cut into a washer) around the lens..