As the title says, I spilled water over my phone whilst trying to put on a screen protector. The water didn't get into the back of the phone, just where the screen is. I put it in a bag of rice overnight (and most of yesterday afternoon), but there are still spots on the screen (see attachment). After a quick test, everything seems to work except the trackball click. So I now have several questions:
- What seems to be the problem specifically (there's water damage obviously, but specifically where)?
- Is it more cost-efficient to fix it myself or take it to a shop?
- If I am to fix it myself, are there guides I can follow and are there special tools I need?
Thank you for your help!
The best you should have done was to take out the battery and and probably get it open so the water evaporates......putting it in a rice bag was not the best idea should have keept it somewhere dry with lots of air blowing over so as to take out the water vapour which would build up as the phone warms up your rice bag method has only locked up water vapour in your device and if that comes into contact with any component that could be serious damage get a tech guy to open it up and let all the water dry up keep in mind that if its not open vapour will just lock up an make your screen look bad:banghead:
Sent from my HTC Desire Z using xda app-developers app
---------- Post added at 06:05 PM ---------- Previous post was at 05:57 PM ----------
For you track that could be the end of it water I the worst thing that you keep near you phone a drop on you CPU RAM or any vital thing and you done DON'T TRY FIXING IT ON YOUR OWN ANY PHONE GUY WILL NOT YOU EXCEPT YOU ARE ONE if your warranty is still somewhere it might help but most warranties don't cover damage caused by you the user..... If you try the above and its still the same then a service center is the next op
Sent from my HTC Desire Z using xda app-developers app
strip419 said:
The best you should have done was to take out the battery and and probably get it open so the water evaporates......putting it in a rice bag was not the best idea should have keept it somewhere dry with lots of air blowing over so as to take out the water vapour which would build up as the phone warms up your rice bag method has only locked up water vapour in your device and if that comes into contact with any component that could be serious damage get a tech guy to open it up and let all the water dry up keep in mind that if its not open vapour will just lock up an make your screen look bad:banghead:
Sent from my HTC Desire Z using xda app-developers app
---------- Post added at 06:05 PM ---------- Previous post was at 05:57 PM ----------
For you track that could be the end of it water I the worst thing that you keep near you phone a drop on you CPU RAM or any vital thing and you done DON'T TRY FIXING IT ON YOUR OWN ANY PHONE GUY WILL NOT YOU EXCEPT YOU ARE ONE if your warranty is still somewhere it might help but most warranties don't cover damage caused by you the user..... If you try the above and its still the same then a service center is the next op
Sent from my HTC Desire Z using xda app-developers app
Click to expand...
Click to collapse
Thanks for the response. I wasn't aware that the rice bag method isn't for all water-related incidents. So the best thing to do right now is to open it up. Does that mean open it to the internals or just take the battery out and blow a fan over the phone? I hope nothing other than the trackball is affected. I can live without the trackball clicking.
Your phone may still die, I had a water damaged desire z, I dropped in in the toilet, thought I was lucky as I had already flushed lol. After drying for a few days (I unfortunately, like you, left the battery in) I booted it and found the flash was acting crazy. By avoiding using it I thought I was ok, but a day later the flash had formed a short circuit rendering the phone useless, the power button rather than booting the device simply made the flash blink like the cm7 strobe effect. Tried further drying by disassembling. Nothing. Binned. Died a little inside. Bought a galaxy mini. Hated it. Sold galaxy mini and now using Motorola defy, got it cos its water resistant XD, its an OK replacement but I miss my z's better touchscreen, and the keyboard rocked, alas that's why they're so unresistant to water though. Hope yours survives, as the trackball is pretty isolated even if it is shorted it might not do much damage hopefully (flash is near camera, power button and proximity which all lead to the motherboard!) let me know how it goes, good luck!
@non4 said:
Your phone may still die, I had a water damaged desire z, I dropped in in the toilet, thought I was lucky as I had already flushed lol. After drying for a few days (I unfortunately, like you, left the battery in) I booted it and found the flash was acting crazy. By avoiding using it I thought I was ok, but a day later the flash had formed a short circuit rendering the phone useless, the power button rather than booting the device simply made the flash blink like the cm7 strobe effect. Tried further drying by disassembling. Nothing. Binned. Died a little inside. Bought a galaxy mini. Hated it. Sold galaxy mini and now using Motorola defy, got it cos its water resistant XD, its an OK replacement but I miss my z's better touchscreen, and the keyboard rocked, alas that's why they're so unresistant to water though. Hope yours survives, as the trackball is pretty isolated even if it is shorted it might not do much damage hopefully (flash is near camera, power button and proximity which all lead to the motherboard!) let me know how it goes, good luck!
Click to expand...
Click to collapse
My sympathies. =( I hope I don't have to replace my phone too.
wcstick said:
My sympathies. =( I hope I don't have to replace my phone too.
Click to expand...
Click to collapse
Just do not put battery in until its as dry as possible and you may be lucky, I soaked the galaxy mini too washing dishes but that one was fine once I dried it, your trackball may start working again if youre patient
---------- Post added at 08:19 PM ---------- Previous post was at 08:17 PM ----------
Oh and I see your earlier question, yes take internals out if possible but carefully to avoid damage, even removing the back to expose the motherboard would be helpful if you don't feel comfortable pulling parts out
Yes all all covers should be out atleast the system board should be as dry as possible cos that's were the trouble is,the track pad uses some kind of optic stuf and could be changed if its removable. If its attached to the system board don't try cos you might brick your phone if your touch screen is good then there should not be a problem, for me I hardly use my track pad. As for it working again I can't assure you of that but open it up it shud work
Sent from my HTC Desire Z using xda app-developers app
@non4 said:
Oh and I see your earlier question, yes take internals out if possible but carefully to avoid damage, even removing the back to expose the motherboard would be helpful if you don't feel comfortable pulling parts out
Click to expand...
Click to collapse
Turns out, I don't have the tools to open it up. I suppose there's no avoiding taking it to a shop to have it fixed.
DON'T FORGET TO CONTACT A GOOD GUY IF YOU ARE NOT SURE OF OPENING IT YOURSELF G2 is a good phone it should be able to survive except you made it swim
Sent from my HTC Desire Z using xda app-developers app
---------- Post added at 07:45 PM ---------- Previous post was at 07:44 PM ----------
HIT THANKS PLSSS SMH.... AM SOOOOOO "THANKS DRY"
Sent from my HTC Desire Z using xda app-developers app
strip419 said:
DON'T FORGET TO CONTACT A GOOD GUY IF YOU ARE NOT SURE OF OPENING IT YOURSELF G2 is a good phone it should be able to survive except you made it swim
Sent from my HTC Desire Z using xda app-developers app
---------- Post added at 07:45 PM ---------- Previous post was at 07:44 PM ----------
HIT THANKS PLSSS SMH.... AM SOOOOOO "THANKS DRY"
Sent from my HTC Desire Z using xda app-developers app
Click to expand...
Click to collapse
Well, I didn't douse it in water. I just spilled water on top of the screen as I was applying a screen protector. If anything, it's just the screen part that's wet, not the other half of the device. Hopefully it won't be an expensive fix either. Anyway, thank you for your help! =)
Good luck dude but incase it dies I can sell you mine :beer::thumbup:
Sent from my HTC Desire Z using xda premium
rice works pretty well pulling out moisture, opening you phone is quite easy if you slightly mechanicaly inclined. you will need a small pry tool (guitar pick should work) and a t5 torx bit. that will get your back case off. there are about a dozen small phillips screws to remove the motherboard and then a few more to get to the digitizer. looks as if the water either seeped in through the front speaker or around the edges of the screen meaning the glue has gone bad.
if your able to fully dry your phone great, but be carefull any moisture left can turn to corrosion quickly.
there is a small ribbon cable that connects your softbutton pad and track to the rest of the phone, if the soft buttons still work but not the track this is most likely what needs to be fixed
if the screen seems unresponsive then you will need to replace the digitzer
Sent from my HTC Vision using xda premium
I dropped this g2 in the toilet a long time ago. Left in rice for a week and dried completely. Used for a week after that and impurities on the board would not let the phone boot up past bootloader and then it'll shut down. I opened it up and using 99% alcohol and a toothbrush cleaned the motherboard. The phone has worked perfectly ever since. The moisture in the screen eventually goes away after a few weeks. In my case i only have a faint line noticeable from certain angles. You can fix it by simply replacing the LCD.
Sent from my HTC Vision using xda app-developers app
I would have taken apart my phone if I had a t5 torx bit. Inconveniently, the smallest I have is a t7. I'm going to take it to a repair place tomorrow and see what's gone bad. I'd rather pay the price for repair now than pay for a new phone.
Related
Hi all, I have a dinc2 and it was dropped in water. It was removed very fast and put In rice. Thought I saved it but it started wigging and only goes to htc screen. I am able to volume down w/ power and get to hboot menu but that's about it. I plug in to comp and it doesn't recognize it. I have the htc sync on my comp. But nothing. Don't have ins. So I would like to get it running. Any and all help appreciated. Thanks, hp
Sent from my DROID X2 using XDA App
Unfortunately there is not much else you can do for water. Maybe let it sit on a window seal in the sun with the back off. Just to try to get any remaining water out. More than likely it will not come back.
Are the water marks turned pink?
Sent from my ADR6350 using xda premium
homephysician said:
Hi all, I have a dinc2 and it was dropped in water. It was removed very fast and put In rice. Thought I saved it but it started wigging and only goes to htc screen. I am able to volume down w/ power and get to hboot menu but that's about it. I plug in to comp and it doesn't recognize it. I have the htc sync on my comp. But nothing. Don't have ins. So I would like to get it running. Any and all help appreciated. Thanks, hp
Sent from my DROID X2 using XDA App
Click to expand...
Click to collapse
Give it a week...happened to my inc1 and after a week it all worked perfectly.
Sent from my ADR6350 using xda premium
homephysician said:
Hi all, I have a dinc2 and it was dropped in water. It was removed very fast and put In rice. Thought I saved it but it started wigging and only goes to htc screen. I am able to volume down w/ power and get to hboot menu but that's about it. I plug in to comp and it doesn't recognize it. I have the htc sync on my comp. But nothing. Don't have ins. So I would like to get it running. Any and all help appreciated. Thanks, hp
Sent from my DROID X2 using XDA App
Click to expand...
Click to collapse
What happens when you get in recovery? Something like a failure to mount certain partitions?
Sent from my ADR6350 using xda premium
I have also had a similar experience with my Eris. I left it on a radiator with the back off and battery/ SD card removed for 24hrs and it came up fine even though my water markers were all triggered. Still works today.
Good luck!
Hi thanks for the replies. The water marks are not pink. When at the recovery window the recovery goes to the htc white screen. The crc calculates. Its been more than a week. The only reason I thought there might be some hope is because it does go to the recovery window. I also notice small pin holes in the back cover. Maybe a master reset or some hope. Thanks again for the help. hp
Sent from my DROID X2 using XDA App
if the water marks are not turned you can file a warranty claim but that is risky due to not knowing what is inside the phone. The outter marks are harder to turn than inner water marks.
Try just letting it dry out like myself and others have said. You do not want to screw things up more messing with it vs letting it work its self out.
Sent from my ADR6350 using xda premium
Thanks man. I don't have insurance on it. But I do appreciate all the responses.
Sent from my DROID X2 using XDA App
homephysician said:
Thanks man. I don't have insurance on it. But I do appreciate all the responses.
Sent from my DROID X2 using XDA App
Click to expand...
Click to collapse
Well if the water marks aren't pink...go to Verizon, play dumb and say it won't turn on?
Sent from my ADR6350 using xda premium
thanks but...., i and now you all know it has water damage. for me to go in to verizon and play dumb would be deceitful. the phone is expensive but not worth lying about. i have to face an all mighty God some day, and possibly sooner than later. its just not worth the risk to me. but i do thank you all for the suggestions. be blessed and happy new year to all. hp
Not sure if it's been a week, but there could still be water in it. I dropped my old iPhone in the toilet, and by the time got it out, the screen was flickering and it was resting randomly. I took it entirely apart and found lots of spots where water reached. Dried them all out, and it still works fine to this day.
At this point, you have nothing to loose, so I'd sit down at a clean table with some small screwdrivers and start tearing it down. I'm sure there are diagrams on the web showing how it comes apart. In addition to water, because of the time that has elapsed, look for spots of corrosion - light green to white dust or flakes. If you see any, you can try brushing it away with a small paintbrush. If the water has all dried up and it's still not working, there has to be a short (or several) somewhere. You might get lucky, and like I said, you have nothing to loose.
Your honesty is much appreciated! Fraudulent warranty claims affect all of us.
If you still haven't gotten it working I recommend a bath in rubbing alcohol for about 30-40 seconds. The higher the alcohol percentage the better, I prefer the 90% stuff. Then another overnight sit in rice. Do both of these with the back cover and battery both removed.
I know it sounds a bit strange to put it in liquid but the alcohol will dilute the water and make it evaporate much faster. The rice will further accelerate this process. I have done it before with great results and at this point you can't do much more harm to it if it isn't even turning on.
Best of luck!
Sent from my Incredible 2 HD using XDA App
cstone1991 said:
Your honesty is much appreciated! Fraudulent warranty claims affect all of us.
If you still haven't gotten it working I recommend a bath in rubbing alcohol for about 30-40 seconds. The higher the alcohol percentage the better, I prefer the 90% stuff. Then another overnight sit in rice. Do both of these with the back cover and battery both removed.
I know it sounds a bit strange to put it in liquid but the alcohol will dilute the water and make it evaporate much faster. The rice will further accelerate this process. I have done it before with great results and at this point you can't do much more harm to it if it isn't even turning on.
Best of luck!
Sent from my Incredible 2 HD using XDA App
Click to expand...
Click to collapse
Take your battery out if you do this.. just sayin...
Sent from my Mikrunny'd Vivo_w
faehsemc said:
Take your battery out if you do this.. just sayin...
Sent from my Mikrunny'd Vivo_w
Click to expand...
Click to collapse
VERY IMPORTANT! I probably should have put that in caps in my post. It was in there though.
Sent from my Incredible 2 HD using XDA App
My friend spilled milk all over her phone, and it wouldn't turn on. I told her to put it in alcohol, and a month later it still works, if a little funny sometimes. But yes, it is important to remove the battery, and the sd card. And let it sit for a while afterwards.
cstone1991 said:
VERY IMPORTANT! I probably should have put that in caps in my post. It was in there though.
Sent from my Incredible 2 HD using XDA App
Click to expand...
Click to collapse
Do you know what alcohol does to the LCD screen...
It left a permanent color band pattern on my 6800.
If you are going to put alcohol any where near it I would do it with a Q-Tip with the covers removed.
Find an old tire compressor, the 12V type and modify the intake of the compressor to connect a suction tube to it.
Swab the area around the components with a soggy Q-Tip (avoid running any on the LCD screen) and work it in with an old tooth brush (make sure the toothbrush is very clean, you don't want to smear any fluoride residue on the solder mask of the circuit board).
Then power up the pump and suck up the excess residue.
Wen prepping the unit, you may want to open all of those ribbon cable clamps.
That's the first place corrosion wants to grow.
Just be sure to handle those cables with care.
The copper traces within them is very thin.
If there is any corrosion on the contacts of the cables, lightly use a pencil eraser on them by holding it flat on a surface add rubbing in one direction away from the main part out to the end.
Good luck...
cac2us said:
Do you know what alcohol does to the LCD screen...
It left a permanent color band pattern on my 6800.
If you are going to put alcohol any where near it I would do it with a Q-Tip with the covers removed.
Find an old tire compressor, the 12V type and modify the intake of the compressor to connect a suction tube to it.
Swab the area around the components with a soggy Q-Tip (avoid running any on the LCD screen) and work it in with an old tooth brush (make sure the toothbrush is very clean, you don't want to smear any fluoride residue on the solder mask of the circuit board).
Then power up the pump and suck up the excess residue.
Wen prepping the unit, you may want to open all of those ribbon cable clamps.
That's the first place corrosion wants to grow.
Just be sure to handle those cables with care.
The copper traces within them is very thin.
If there is any corrosion on the contacts of the cables, lightly use a pencil eraser on them by holding it flat on a surface add rubbing in one direction away from the main part out to the end.
Good luck...
Click to expand...
Click to collapse
Hmm... I never thought about that but I can definitely see how damage to the screen is possible. I have never seen it happen to phones that I or anyone I know have tried it on but I have never tried it on a touchscreen phone, which could definitely be different.
Thank you for posting a much safer method!
Sent from my Incredible 2 HD using XDA App
I had dropped my phone and needed new glass. The digitizer was fine. Here is the site I bought my screen from.
http://www.parts4repair.com/samsung-galaxy-s-ii-epic-4g-touch-d710-spint/
Chris
cbunting99 said:
I had dropped my phone and needed new glass. The digitizer was fine. Here is the site I bought my screen from.
http://www.parts4repair.com/samsung-galaxy-s-ii-epic-4g-touch-d710-spint/
Chris
Click to expand...
Click to collapse
The glass is the digitizer... It also houses the soft keys as well. It is fused to the screen and will require a heat gun or heat plate to separate from the screen properly. This post is full of misinformation. You will need to purchase either both the screen and digitizer separately or as a single unit. It will be almost impossible for you to replace just the glass unless you have access to some very expensive equipment to separate it and fuse the replacement in place properly.
I've watched several videos on youtube showing the removal of just the screen from the digitizer on the S3. The guys on there use either a heat gun or hair dryer and don't have to disassemble the phone to replace just the glass. Do a search and watch a few and see if you want to tackle it. Mine has a crack in it and I'm considering trying it to see if I can.
stonesaber said:
I've watched several videos on youtube showing the removal of just the screen from the digitizer on the S3. The guys on there use either a heat gun or hair dryer and don't have to disassemble the phone to replace just the glass. Do a search and watch a few and see if you want to tackle it. Mine has a crack in it and I'm considering trying it to see if I can.
Click to expand...
Click to collapse
You should always disassemble the device when applying heat to it for a repair. Heat kills electronics. There is plastic inside the phone that can and will melt when heat is applied. Like the power and volume buttons. Ribbon cables can also be damaged. There is also rubber inside.
graydiggy said:
You should always disassemble the device when applying heat to it for a repair. Heat kills electronics. There is plastic inside the phone that can and will melt when heat is applied. Like the power and volume buttons. Ribbon cables can also be damaged. There is also rubber inside.
Click to expand...
Click to collapse
Yeah, cause they never get left in a hot car. Or out in the hot August sun in Florida. Etc.
I'm not suggesting you use the max heat setting on one. Some common sense should be used.
Okay....This is a bad idea...
I used to work for the repair center at Sprint and I was quite good at it, it takes quite a lot of heat to remove those screens from the digitizer. If you apply that heat to an assembled phone, then at the very least you will destroy the LCD.
Also ribbons are VERRRRY sensitive.
And you should not be leaving your phone in the car in the summer...That is just stupid.
stonesaber said:
Yeah, cause they never get left in a hot car. Or out in the hot August sun in Florida. Etc.
I'm not suggesting you use the max heat setting on one. Some common sense should be used.
Click to expand...
Click to collapse
You also stated the videos were from the S3. A completely different phone.
If you want to kill your phone, that's all you. But do not come here telling people it is ok to do crazy stuff like that on their phone. I have worked in phone repair and small electronics repair for 6 years and know for a fact that it takes a high amount of heat to separate the digitizer assembly from the actual screen itself. There are proper methods of doing things, and then there is the method and shortcuts that some jackass came up with and got lucky on. But 90% of the time, it is a failure causing more damage if not completely breaking the device as a whole. Furthermore, A hot car in FL produces nothing compared to the heat of a heat gun or heat plate. And using a hair dryer? I am laughing at you right now.
Stop being a jerk. I didn't suggest anyone do anything but to check out a few videos and to make their OWN decision. I just love internet know-it-alls. If I decide to experiment on my phone, then what's it to anyone on here? My phone, my decision. If it works, then great, if not then guess what? It's my phone, my fault. Don't come on here with your holier than thou attitude and assume you know who you're calling out.
Again, I pointed out that there are people who have successfully removed their screens on their S3's. And the OP should check them out and decide for him/herself. As for the hair dryer, laugh all you want, but if you're gonna try it, then that's precisely what I would try first due to the low temperature output to see if it was even a viable option to unseat the glass from the adhesive beneath.
And lastly. Why not try a cheaper alternative if you need to replace the glass anyway? In my case, I'm not filing an insurance claim and I'm not going to get mine repaired at a repair center. So if I attempt just a screen replacement and I am unsuccessful, then I replace the digitizer/screen assy. anyway. I don't see what's so crazy about that.
---------- Post added at 09:44 AM ---------- Previous post was at 09:39 AM ----------
Censura_Umbra said:
And you should not be leaving your phone in the car in the summer...That is just stupid.
Click to expand...
Click to collapse
I did not suggest you should leave your phone in a hot car. I'm merely illustrating a point. Todays phones go through quality control measures and I'm sure they test them in real world conditions. For a lot of people a phone is just a tool and sometimes they leave them places that you or I would probably would not because they are not as OCD about their electronics.
...did you even read our comments? If you use a heat gun on your assembled phone, you will likely FRY YOUR MOTHERBOARD. There will be no purchasing of new screen as you would need a whole new phone. Though these phones are only $180 these days.
Still you suggested something that is very likely to break a phone without so much as a "this might be a bad idea".
There are "internet-know-it-alls" and there are people who know what they are talking about. You are the former, we are the latter.
Sent from my Nexus 7 using xda app-developers app
Censura_Umbra said:
...did you even read our comments? If you use a heat gun on your assembled phone, you will likely FRY YOUR MOTHERBOARD. There will be no purchasing of new screen as you would need a whole new phone. Though these phones are only $180 these days.
Still you suggested something that is very likely to break a phone without so much as a "this might be a bad idea".
There are "internet-know-it-alls" and there are people who know what they are talking about. You are the former, we are the latter.
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Thank you for setting me straight oh great one.
If you are ok with possibly breaking your phone even more then go for it. I like to DIY things too and sometimes the results are good and other times I break stuff. Either way its still fun. Let us know how it turns out.
I sell complete screens for $50 much easier to replace as well.
Sent from my Genesis that does what Nintendon't
tuscani1821 said:
I sell complete screens for $50 much easier to replace as well.
Sent from my Genesis that does what Nintendon't
Click to expand...
Click to collapse
Where are you selling the glass/digitizer for $50?
Sent from my Nexus 7 using xda premium
jirafabo said:
Where are you selling the glass/digitizer for $50?
Sent from my Nexus 7 using xda premium
Click to expand...
Click to collapse
Through private pm's. I have lots of feedback as well in the epic touch q&a
Sent from my EVO using Tapatalk 2
stonesaber said:
Stop being a jerk. I didn't suggest anyone do anything but to check out a few videos and to make their OWN decision. I just love internet know-it-alls. If I decide to experiment on my phone, then what's it to anyone on here? My phone, my decision. If it works, then great, if not then guess what? It's my phone, my fault. Don't come on here with your holier than thou attitude and assume you know who you're calling out.
Again, I pointed out that there are people who have successfully removed their screens on their S3's. And the OP should check them out and decide for him/herself. As for the hair dryer, laugh all you want, but if you're gonna try it, then that's precisely what I would try first due to the low temperature output to see if it was even a viable option to unseat the glass from the adhesive beneath.
And lastly. Why not try a cheaper alternative if you need to replace the glass anyway? In my case, I'm not filing an insurance claim and I'm not going to get mine repaired at a repair center. So if I attempt just a screen replacement and I am unsuccessful, then I replace the digitizer/screen assy. anyway. I don't see what's so crazy about that.
---------- Post added at 09:44 AM ---------- Previous post was at 09:39 AM ----------
I did not suggest you should leave your phone in a hot car. I'm merely illustrating a point. Todays phones go through quality control measures and I'm sure they test them in real world conditions. For a lot of people a phone is just a tool and sometimes they leave them places that you or I would probably would not because they are not as OCD about their electronics.
Click to expand...
Click to collapse
I think they are just worried noobs will find this thread on Google, destroy their phone, and blame xda as a whole; by not having really good warnings and fully testing something, it might give the false impression that it's a good idea when maybe it's not...
That said, everyone should be cool to each other, we're all working and learning together. Isn't the goal to have a good time and gain knowledge?
sent from my ET4G on Paranoid Android using XDA Developers App in hybrid mode
---------- Post added at 01:49 AM ---------- Previous post was at 01:47 AM ----------
tuscani1821 said:
I sell complete screens for $50 much easier to replace as well.
Sent from my Genesis that does what Nintendon't
Click to expand...
Click to collapse
That sounds more than reasonable, and it's a community based solution too.
sent from my ET4G on Paranoid Android using XDA Developers App in hybrid mode
Never heard back from the OP on this one
someguyatx said:
Never heard back from the OP on this one
Click to expand...
Click to collapse
Whoops i responded to a zombie thread that was bumped because of a side topic, lol
sent from my ET4G on Paranoid Android using XDA Developers App in hybrid mode
Stupid me.. Tried to put the phone in my pocket, instead I missed my pocket, and dropped it to the ground... That was maybe like 2feet... :<
I'm wondering how you guys change just the glass. The digitizer works fine.
I see on youtube video on how to replace screen, but what i'm wondering is... How easy is it to mess up the digitzer and you gotta replace the whole thing...
Any i'm going to be using a hair dryer for the heat... I see some people get air bubble, anyway to prevent that?
You should never use a hair dryer with your phone as it could melt the inside components of the phone. To remove air bubbles try using a squeegee screen protector manufacturers provide with their screen protector.
Another question, when putting those guitar picks in... Where do I put it? The gap in between the bezel, or the gap on the front of the screen between the bezel and the screen? Anyone get what I'm trying to safe?
Katawazaki said:
You should never use a hair dryer with your phone as it could melt the inside components of the phone. To remove air bubbles try using a squeegee screen protector manufacturers provide with their screen protector.
Click to expand...
Click to collapse
He's not talking about using a hair dryer to take out air bubbles. He's talking about using a hair dryer to separate the broken glass from the digitizer
Sent from my SGH-M919 using XDA Premium 4 mobile app
---------- Post added at 01:57 AM ---------- Previous post was at 01:54 AM ----------
This guide for the s3 explains the process well. I did my dad's following it:
http://forum.xda-developers.com/showthread.php?t=1890708
Sent from my SGH-M919 using XDA Premium 4 mobile app
Imo, if you don't have insurance, bring it to an establishment that changers the glass/digitizer assembly by the tons. It'll cost you a few bucks but it'll be done righ, dand that'll be that.
I've read about individuals who have completed the job successfully, but I don't think it's a simple task, in addition, when someone attempts a disassembly/assembly installation for the first time, and may be the only time, no doubt that you will run into the little things where the answers won't be forthcoming, and/or there will be little things to look for, or little tricks to do, which you won't be aware of, or you'll need a part or tool that will have to wait for to the next day, etc. etc.
But you may attempt it after watching some videos, and could be successful on your first attempt, and it's always fun to tinker.
I've seen someone attempt the assembly on their Nexus, and they broke the wifi antenna which is easy to do, and the guy spent days between figuring out the issue, getting the parts, then screwing up the glue for the glass, etc. etc.
And Never got it right. Bubbles, etc.
First attempts usually have trials and tribulations, but subsequent repairs usually will go much smoother.
My 5 cents.. Coming from someone who likes to tinker
I used this guide to do mine:
http://www.ifixit.com/Answers/View/129542/Front+Glass+screen+replacement
Sent from my SGH-M919 using XDA Premium 4 mobile app
Hey guys , a friend of mine have a htc one x , but it felt in a glass of water, when i try to boot it,blank screen , when i put it on the charger the light turn, where you cen see if the phone is fully charged or not , but is there a tool for the htc were i can see the boot process? So i know with parts i need to replace.
Greetings max
Sent from my HTC Desire using xda app-developers app
Try keeping it in dry rice for 24 hours so that all moisture gets soaked. Then report back.
Sent from my One X
athulele said:
Try keeping it in dry rice for 24 hours so that all moisture gets soaked. Then report back.
Sent from my One X
Click to expand...
Click to collapse
Could also open it and get a hair drier on it.
Used to do that when I was a sound tech, came in very handy a number of times.
Sent from my One X using xda app-developers app
Put it in the rice..Rice will take water out..
Sent from my EndeavorU using Tapatalk 2
I ve all redy done that, with no success (sorry for my english, i am dutch
Sent from my HTC Desire using xda app-developers app
I didn't tried that , but if rice didn't work, why should a hair dryer help? (I m gonna to try it but a bigger prob .. Where are the screws in the one x xD i m gonna to ask it on youtube , but thx for your reactions guys!
Sent from my HTC Desire using xda app-developers app
If you want to get the One X open you'll need to pop the screen out of the casing using a thin tool (or your thumbs if you're feeling brave).
The motherboard and everything else is attached to the screen, and is also secured by adhesive. Getting the phone open is not easy and you could easily damage it, so if you're going to try this be careful. There are a few vids on YouTube detailing how to open the One X.
Your success will depend on exactly what damage the water has done to the phone. If its fried the motherboard then it's pretty much game over. You may have got lucky and the damage may be restricted to the power flex cable or battery, which can be replaced. Both parts can be ordered for a very low price. Unfortunately the One X is one of the worst phones to drop in water, as you can't immediately take the battery or anything else out. It's very easy for this phone to short-circuit, though if you can get it to turn on and boot to the "HTC quietly brilliant" screen you have half a chance of salvaging it.
de4life said:
If you want to get the One X open you'll need to pop the screen out of the casing using a thin tool (or your thumbs if you're feeling brave).
The motherboard and everything else is attached to the screen, and is also secured by adhesive. Getting the phone open is not easy and you could easily damage it, so if you're going to try this be careful. There are a few vids on YouTube detailing how to open the One X.
Your success will depend on exactly what damage the water has done to the phone. If its fried the motherboard then it's pretty much game over. You may have got lucky and the damage may be restricted to the power flex cable or battery, which can be replaced. Both parts can be ordered for a very low price. Unfortunately the One X is one of the worst phones to drop in water, as you can't immediately take the battery or anything else out. It's very easy for this phone to short-circuit, though if you can get it to turn on and boot to the "HTC quietly brilliant" screen you have half a chance of salvaging it.
Click to expand...
Click to collapse
Actually taking the housing off is very easy.
Makes sure phone is off, take out sim tray then pop off the bottom.
Also rice may work but it doesn't absorb moisture that quickly, salt for example absorbs must faster than rice. Putting it in a tub (sandwich box type thing) with packets of silica gel (the random do not eat packets you get with shoes and stuff) would be far more effective.
Sent from my One X using xda app-developers app
treebill said:
Actually taking the housing off is very easy.
Makes sure phone is off, take out sim tray then pop off the bottom.
Also rice may work but it doesn't absorb moisture that quickly, salt for example absorbs must faster than rice. Putting it in a tub (sandwich box type thing) with packets of silica gel (the random do not eat packets you get with shoes and stuff) would be far more effective.
Sent from my One X using xda app-developers app
Click to expand...
Click to collapse
Very easy is extremely misleading. The Phone is not meant to be taken apart and as a result it is not very easy to do so. I'd hate for anybody to read that and think they can just pop off the bottom without damaging anything. It wouldn't take much to crack the screen, damage the logic board or indeed one of the internal cables from just attempting to pop it off without any caution. You also have the issue of the insides being stuck down with adhesive, which makes it difficult to open the phone for the first time. It's easier upon subsequent attempts. The battery is also stuck down making it hard to get out.
Well, Max, connecting a wet phone to the mains and trying to power it on is possibly the worst thing you can ever do to a wet phone. I'd say there's no chance, unless for whatever reason you haven't fried the phone's guts already.
Sent from my One X using Tapatalk
de4life said:
Very easy is extremely misleading. The Phone is not meant to be taken apart and as a result it is not very easy to do so. I'd hate for anybody to read that and think they can just pop off the bottom without damaging anything. It wouldn't take much to crack the screen, damage the logic board or indeed one of the internal cables from just attempting to pop it off without any caution. You also have the issue of the insides being stuck down with adhesive, which makes it difficult to open the phone for the first time. It's easier upon subsequent attempts. The battery is also stuck down making it hard to get out.
Click to expand...
Click to collapse
Removing the outer housing is very simple, just apply a bit of force and the case will come out.
Even the first time I opened my phone I did so without much effort and didn't break anything.
Sent from my One X using xda app-developers app
treebill said:
Removing the outer housing is very simple, just apply a bit of force and the case will come out.
Even the first time I opened my phone I did so without much effort and didn't break anything.
Sent from my One X using xda app-developers app
Click to expand...
Click to collapse
I think you might have just had loose casing for whatever reason. You only have to view a few vids on YouTube to see it isn't an easy process and it would be very easy to break something if done incorrectly.
de4life said:
I think you might have just had loose casing for whatever reason. You only have to view a few vids on YouTube to see it isn't an easy process and it would be very easy to break something if done incorrectly.
Click to expand...
Click to collapse
First time was harder, applied quite a bit of force.
Once you get the pressure clips off you can feel the adhesive pealing off.
Sent from my One X using xda app-developers app
ehmad
hey i dropped my htc one x on wet floor. its display got turned off but yet it was reponsive. i could atend calls. i took it to the htc official store and they told me to get its motheroard replaced. can anyone help me where i can find a new motherboard?
muhammad.uzi1994 said:
hey i dropped my htc one x on wet floor. its display got turned off but yet it was reponsive. i could atend calls. i took it to the htc official store and they told me to get its motheroard replaced. can anyone help me where i can find a new motherboard?
Click to expand...
Click to collapse
Only in official HTC service.
Thant said:
Only in official HTC service.
Click to expand...
Click to collapse
but they are charging way too much more than the phones worth, what to do can you help?
muhammad.uzi1994 said:
but they are charging way too much more than the phones worth, what to do can you help?
Click to expand...
Click to collapse
No go and by new phone. Sorry
muhammad.uzi1994 said:
but they are charging way too much more than the phones worth, what to do can you help?
Click to expand...
Click to collapse
Try the hair dryer/rice method. And keep using it till it works.
Sent from my One X
*update* i've got the htc turned on , i ve heard the pling sound when you turn it on, all buttons work except the screen , the is black ... Note : when i put him in the bootloader and insert the charger , the led is starting to flash 3 times , then 3 sec noting and then it is going to flash again so
Greetings ,
Max
Sent from my HTC Desire using xda app-developers app
I used the rice method
Sent from my HTC Desire using xda app-developers app
Alcohol problems
So, I was rubbing off a sticker from the back of my phone using a small towel dipped in pure alcohol. This phone is supposed to be waterproof and I put my back cover on the front for extra security. But, after I was done, dried it and everything, I realized that some alcohol had gotten inside the screen, I have no idea why. The whole display was dark pruple-ish and covered in stains and some weird things like dark dark spots and lines. I researched it ans found out that it was okay because alcohol evaporates really easily, so I decided to use it for a bit, since I have huge overheating issues (often going up to about 45-50°C upon usage). After half an hour of usage (it had gotten pretty hot), the display seemed to become a little bit clearer and less dark, but I decided that I should stop using it in fear of moving some bubble or ruining my already dying screen, so I put it to charge and left it alone. I was relying on my country's hot weather to finish the job, and I was checking on it every once in a while. At first, it seemed to get better but suddenly, after about 2 or 3 hours, the screen stopped turning on at all. Neuther the display nor the touch were working anymore, but sound (modifying volume) and vibration (haptic feedback for holding down "power") worked really well. I tried to restarted (volume up + power), but nothing more than some vibrations and jingles. Currently, my phone is turned off (volume down + power) and I'll leave it like this overnight, to see if anything improves tomorrow.
So, I need to know. Is my screen ruined and needs changing, or simply evaporating the alcohol will fix everything? Also, if I have to change my phone, is there a way to use HTC backup to transfer data without the "old" phone?
Thank you in advance!
Laslas19 said:
So, I need to know. Is my screen ruined and needs changing, or simply evaporating the alcohol will fix everything? Also, if I have to change my phone, is there a way to use HTC backup to transfer data without the "old" phone?
Thank you in advance!
Click to expand...
Click to collapse
Hello mate, bad luck with that happening..
First off the phone is not waterproof, it does have an ip rating but it's not up there with phones you can take with you for a dip.
As for the moisture, try a silica gel pack in an air tight bag for a few hours or over night, there are packs you can buy online for this specific treatment, if the alcohol has hit something critical then it could be game over..
Try the drying out techniques, you can find many of them online..
Drying the alcohol up shouldn't be hard but like I said if damage is done then it's done mate.
Just one question, why use alcohol on your phone? Wouldn't a baby wipe or a damp cloth do the same?
dladz said:
Hello mate, bad luck with that happening..
First off the phone is not waterproof, it does have an ip rating but it's not up there with phones you can take with you for a dip.
As for the moisture, try a silica gel pack in an air tight bag for a few hours or over night, there are packs you can buy online for this specific treatment, if the alcohol has hit something critical then it could be game over..
Try the drying out techniques, you can find many of them online..
Just one question, why use alcohol on your phone? Wouldn't a baby wipe or a damp cloth do the same?
Click to expand...
Click to collapse
First of all, thanks a lot for your help, I will try your suggestions and keep you up to date.
Second of all, by "game over" do you mean for the screen or the entire phone? Because the phone itself seems to work just fine apart from the screen.
And, finally, that was a really tenacious sticker that I tried to remove for days. I know it sounds stupid that I used alcohol but nothing else worked. Good thing I didn't resolve to boiling water first. There is one positive point about this whole story: the sticker is now completely gone.
EDIT: I forgot to say that I made a mistake: the phone is not supposed to be "waterproof" as I previously said, but it is clearly stated on its booklet that it is "splash proof". I guess that does make a difference and I ask to be excused from my dumbness.
How much alcohol did you use... You're only meant to damp a cloth an rub lightly.. It would seem to me you poured it on.
I wish I stole my HTC M9. It's a pile of ****.
shivadow said:
How much alcohol did you use... You're only meant to damp a cloth an rub lightly.. It would seem to me you poured it on.
I wish I stole my HTC M9. It's a pile of ****.
Click to expand...
Click to collapse
Well "rubbing lightly" surely isn't the word because it didn't work but I did damp a cloth and rubbed strongly enough for the alcohol to actually come out of the cloth and slide off the sides of the phone. I did meticulously dry it with tissues tho, but it must have been too late.
Oh, and by the way, I do hear my new email jingle coming out of it (because turns out power+volume down can't turn it off, I can just restart it with power+volume up) when I get an email notification from xda. So I am guaranteed that wifi, gmail and the speakers still work at least. I think the main problem is the screen.
I think something either controlling or part of the screen has popped by shorting out.
It's tough to call but the fact the phone still responds is promising!.
Give htc a call and just tell them it went off one day and wouldn't come on. Any evidence should have literally evaporated into thin air by then. Hopefully they'll arrange something.
I wish I stole my HTC M9. It's a pile of ****.
shivadow said:
I think something either controlling or part of the screen has popped by shorting out.
It's tough to call but the fact the phone still responds is promising!.
Give htc a call and just tell them it went off one day and wouldn't come on. Any evidence should have literally evaporated into thin air by then. Hopefully they'll arrange something.
I wish I stole my HTC M9. It's a pile of ****.
Click to expand...
Click to collapse
Thank you for your help! Unfortunately if I want to send my phone to HTC I'll have to send it to another country because there's not much support here and it will be really complicated. But, if I understand correctly, just changing the screen should fix the problem. It won't be cheap but definitely cheaper and easier than getting and setting up a new phone.
Thanks again for the advice!
Laslas19 said:
Thank you for your help! Unfortunately if I want to send my phone to HTC I'll have to send it to another country because there's not much support here and it will be really complicated. But, if I understand correctly, just changing the screen should fix the problem. It won't be cheap but definitely cheaper and easier than getting and setting up a new phone.
Thanks again for the advice!
Click to expand...
Click to collapse
Changing the screen should work, just as long as it is 100% the screen and not some controller on the motherboard. Personally I agree with the other user who suggested sending it to htc, in all fairness htc should help you out in this case, it's obvious that it shouldn't have went off in that fashion.
I've sent my prime off overseas before, I get it back in around 5 days, great service. At the very least, speak with HTC and see what can be done and expected timelines. Changing the screen even on a one x was a tedious process, I've broken a device in the process, wasn't even mine so please take care if you go down that road, not to mention it's not exactly cheap.
BTW when I said game over I was referring to a simple method not being available to fix your phone and lastly, if you swap out the screen, you will more than likely lose your warranty.
Click thanks to the ppl who've tried to help you BTW
---------- Post added at 08:09 AM ---------- Previous post was at 08:06 AM ----------
shivadow said:
I wish I stole my HTC M9. It's a pile of ****.
Click to expand...
Click to collapse
? Can't think of a better phone out at the moment, in fact I know there isn't.. Maybe the one plus 2? Nah I'd stick with the HTC.