Replacement Glass / OEM Touch Lens ($5) - Samsung Epic 4G Touch

I had dropped my phone and needed new glass. The digitizer was fine. Here is the site I bought my screen from.
http://www.parts4repair.com/samsung-galaxy-s-ii-epic-4g-touch-d710-spint/
Chris

cbunting99 said:
I had dropped my phone and needed new glass. The digitizer was fine. Here is the site I bought my screen from.
http://www.parts4repair.com/samsung-galaxy-s-ii-epic-4g-touch-d710-spint/
Chris
Click to expand...
Click to collapse
The glass is the digitizer... It also houses the soft keys as well. It is fused to the screen and will require a heat gun or heat plate to separate from the screen properly. This post is full of misinformation. You will need to purchase either both the screen and digitizer separately or as a single unit. It will be almost impossible for you to replace just the glass unless you have access to some very expensive equipment to separate it and fuse the replacement in place properly.

I've watched several videos on youtube showing the removal of just the screen from the digitizer on the S3. The guys on there use either a heat gun or hair dryer and don't have to disassemble the phone to replace just the glass. Do a search and watch a few and see if you want to tackle it. Mine has a crack in it and I'm considering trying it to see if I can.

stonesaber said:
I've watched several videos on youtube showing the removal of just the screen from the digitizer on the S3. The guys on there use either a heat gun or hair dryer and don't have to disassemble the phone to replace just the glass. Do a search and watch a few and see if you want to tackle it. Mine has a crack in it and I'm considering trying it to see if I can.
Click to expand...
Click to collapse
You should always disassemble the device when applying heat to it for a repair. Heat kills electronics. There is plastic inside the phone that can and will melt when heat is applied. Like the power and volume buttons. Ribbon cables can also be damaged. There is also rubber inside.

graydiggy said:
You should always disassemble the device when applying heat to it for a repair. Heat kills electronics. There is plastic inside the phone that can and will melt when heat is applied. Like the power and volume buttons. Ribbon cables can also be damaged. There is also rubber inside.
Click to expand...
Click to collapse
Yeah, cause they never get left in a hot car. Or out in the hot August sun in Florida. Etc.
I'm not suggesting you use the max heat setting on one. Some common sense should be used.

Okay....This is a bad idea...
I used to work for the repair center at Sprint and I was quite good at it, it takes quite a lot of heat to remove those screens from the digitizer. If you apply that heat to an assembled phone, then at the very least you will destroy the LCD.
Also ribbons are VERRRRY sensitive.
And you should not be leaving your phone in the car in the summer...That is just stupid.

stonesaber said:
Yeah, cause they never get left in a hot car. Or out in the hot August sun in Florida. Etc.
I'm not suggesting you use the max heat setting on one. Some common sense should be used.
Click to expand...
Click to collapse
You also stated the videos were from the S3. A completely different phone.
If you want to kill your phone, that's all you. But do not come here telling people it is ok to do crazy stuff like that on their phone. I have worked in phone repair and small electronics repair for 6 years and know for a fact that it takes a high amount of heat to separate the digitizer assembly from the actual screen itself. There are proper methods of doing things, and then there is the method and shortcuts that some jackass came up with and got lucky on. But 90% of the time, it is a failure causing more damage if not completely breaking the device as a whole. Furthermore, A hot car in FL produces nothing compared to the heat of a heat gun or heat plate. And using a hair dryer? I am laughing at you right now.

Stop being a jerk. I didn't suggest anyone do anything but to check out a few videos and to make their OWN decision. I just love internet know-it-alls. If I decide to experiment on my phone, then what's it to anyone on here? My phone, my decision. If it works, then great, if not then guess what? It's my phone, my fault. Don't come on here with your holier than thou attitude and assume you know who you're calling out.
Again, I pointed out that there are people who have successfully removed their screens on their S3's. And the OP should check them out and decide for him/herself. As for the hair dryer, laugh all you want, but if you're gonna try it, then that's precisely what I would try first due to the low temperature output to see if it was even a viable option to unseat the glass from the adhesive beneath.
And lastly. Why not try a cheaper alternative if you need to replace the glass anyway? In my case, I'm not filing an insurance claim and I'm not going to get mine repaired at a repair center. So if I attempt just a screen replacement and I am unsuccessful, then I replace the digitizer/screen assy. anyway. I don't see what's so crazy about that.
---------- Post added at 09:44 AM ---------- Previous post was at 09:39 AM ----------
Censura_Umbra said:
And you should not be leaving your phone in the car in the summer...That is just stupid.
Click to expand...
Click to collapse
I did not suggest you should leave your phone in a hot car. I'm merely illustrating a point. Todays phones go through quality control measures and I'm sure they test them in real world conditions. For a lot of people a phone is just a tool and sometimes they leave them places that you or I would probably would not because they are not as OCD about their electronics.

...did you even read our comments? If you use a heat gun on your assembled phone, you will likely FRY YOUR MOTHERBOARD. There will be no purchasing of new screen as you would need a whole new phone. Though these phones are only $180 these days.
Still you suggested something that is very likely to break a phone without so much as a "this might be a bad idea".
There are "internet-know-it-alls" and there are people who know what they are talking about. You are the former, we are the latter.
Sent from my Nexus 7 using xda app-developers app

Censura_Umbra said:
...did you even read our comments? If you use a heat gun on your assembled phone, you will likely FRY YOUR MOTHERBOARD. There will be no purchasing of new screen as you would need a whole new phone. Though these phones are only $180 these days.
Still you suggested something that is very likely to break a phone without so much as a "this might be a bad idea".
There are "internet-know-it-alls" and there are people who know what they are talking about. You are the former, we are the latter.
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Thank you for setting me straight oh great one.

If you are ok with possibly breaking your phone even more then go for it. I like to DIY things too and sometimes the results are good and other times I break stuff. Either way its still fun. Let us know how it turns out.

I sell complete screens for $50 much easier to replace as well.
Sent from my Genesis that does what Nintendon't

tuscani1821 said:
I sell complete screens for $50 much easier to replace as well.
Sent from my Genesis that does what Nintendon't
Click to expand...
Click to collapse
Where are you selling the glass/digitizer for $50?
Sent from my Nexus 7 using xda premium

jirafabo said:
Where are you selling the glass/digitizer for $50?
Sent from my Nexus 7 using xda premium
Click to expand...
Click to collapse
Through private pm's. I have lots of feedback as well in the epic touch q&a
Sent from my EVO using Tapatalk 2

stonesaber said:
Stop being a jerk. I didn't suggest anyone do anything but to check out a few videos and to make their OWN decision. I just love internet know-it-alls. If I decide to experiment on my phone, then what's it to anyone on here? My phone, my decision. If it works, then great, if not then guess what? It's my phone, my fault. Don't come on here with your holier than thou attitude and assume you know who you're calling out.
Again, I pointed out that there are people who have successfully removed their screens on their S3's. And the OP should check them out and decide for him/herself. As for the hair dryer, laugh all you want, but if you're gonna try it, then that's precisely what I would try first due to the low temperature output to see if it was even a viable option to unseat the glass from the adhesive beneath.
And lastly. Why not try a cheaper alternative if you need to replace the glass anyway? In my case, I'm not filing an insurance claim and I'm not going to get mine repaired at a repair center. So if I attempt just a screen replacement and I am unsuccessful, then I replace the digitizer/screen assy. anyway. I don't see what's so crazy about that.
---------- Post added at 09:44 AM ---------- Previous post was at 09:39 AM ----------
I did not suggest you should leave your phone in a hot car. I'm merely illustrating a point. Todays phones go through quality control measures and I'm sure they test them in real world conditions. For a lot of people a phone is just a tool and sometimes they leave them places that you or I would probably would not because they are not as OCD about their electronics.
Click to expand...
Click to collapse
I think they are just worried noobs will find this thread on Google, destroy their phone, and blame xda as a whole; by not having really good warnings and fully testing something, it might give the false impression that it's a good idea when maybe it's not...
That said, everyone should be cool to each other, we're all working and learning together. Isn't the goal to have a good time and gain knowledge?
sent from my ET4G on Paranoid Android using XDA Developers App in hybrid mode
---------- Post added at 01:49 AM ---------- Previous post was at 01:47 AM ----------
tuscani1821 said:
I sell complete screens for $50 much easier to replace as well.
Sent from my Genesis that does what Nintendon't
Click to expand...
Click to collapse
That sounds more than reasonable, and it's a community based solution too.
sent from my ET4G on Paranoid Android using XDA Developers App in hybrid mode

Never heard back from the OP on this one

someguyatx said:
Never heard back from the OP on this one
Click to expand...
Click to collapse
Whoops i responded to a zombie thread that was bumped because of a side topic, lol
sent from my ET4G on Paranoid Android using XDA Developers App in hybrid mode

Related

looking to replace the AMOLED screen on my Vibrant

ok so I managed to crack the screen..nice big shatter mark under the screen and now the entire screen went black...insurance is a pain and from what I understand getting Asurion to replace my vibrant will be $130 and buying an AMOLED screen itself is cheaper.
The rest of the phone is still in working condition as before my screen went totally black after it broke some of it was still functional.
Any idea on where I can get the screen? I have not had luck on ebay as of yet, and was hoping someone here could recco a reputable vendor...
Aliexpress? aliexpress DOTcom/product-fm/342627474-Touch-Digitizer-LCD-Display-AMOLED-Screen-origianl-i9000-for-T-Mobile-Samsung-Vibrant-t959-Wholesale-wholesalers.html
Etech? etech DOTcom/cell-phones-lcd-screens--c1144_1156?page=3&m_id=12&sort=20a
www.cnn.cn maybe? it about $70 +sh
Wow wish I would had found this post sooner...
I dropped my vibrant from my and it was in the case.. it landed flat on the screen..glass did not break but AMOLED screen enploded.. I didnt know until i got to my car and tried to make a call. Crap...I dish out the $130.00 bucks ...bummed out about that..
oh man ...
Still great site and price. Thanks
Thanks I'll try cnn.cn. I see some decent reviews about them.
Is there a tutorial on how to replace this? Or would you have to get someone to do it?
Sent from my SGH-T959 using XDA App
noemberday said:
Is there a tutorial on how to replace this? Or would you have to get someone to do it?
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
youtube.. just search for it..
I cracked my screen also. I found that site after I put in the claim. So I figured what the hell and started taking it apart, for next time.
It isn't easy! I'm pretty nerdy and good with my hands. Be very careful and very patient. There are small parts and wires that can very easily break.
Sent from a Samsung Vibrant.
ok so I got the screen...and this thing is hard as hell to swap...anyone have any ideas? I dont want to further damage anything...
I did find this... http://www.careace.net/2010/06/09/disassembly-of-the-samsung-galaxy-s/
FYI incase anyone else is looking for where to buy from.
http://www.globaldirectparts.com/Samsung-T959-LCD-Digitizer-p/smsng6085995.htm
Have you had any luck with this?I own an Orange San Francisco and cracked the amoled,unfortunately orange or any other site/company offers any repair AFAIK. I'm looking into repairing it myself, are amoled connectors compatible from one phone to another or are they manufacturer specific if you are aware of? I know this is a long shot but it doesn't hurt asking.
Chrishas said:
Have you had any luck with this?I own an Orange San Francisco and cracked the amoled,unfortunately orange or any other site/company offers any repair AFAIK. I'm looking into repairing it myself, are amoled connectors compatible from one phone to another or are they manufacturer specific if you are aware of? I know this is a long shot but it doesn't hurt asking.
Click to expand...
Click to collapse
it would most likely have to be the same part
because the Galaxy S series are the only ones with that size AMOLED screen.
been there done that
i got a vibrant off of something awful for pretty cheap with a broken screen
first off you literally have to pry the screen off of the phone
and the bottom four buttons? there is a very thin ribbon cable that is glued to the screen
there are a few things youll need
1.really small screw driver (i got a glasses repair kit from the dollar store. worked great)
2.something to pry the screen off (used a screw driver from said kit)
3.balls. that ribbon cable is very very easy to break
first off you have to take apart the phone completely
i would even take off the one board that the screen connects to
then you need to pry off the screen very carefully
if your amold or whatever part is broken you're going to have to peel it off
it really sucks and makes you look like a bad 70s disco
after that it gets pretty simple
make sure you have something to hold the top and bottom part to the phone
mine isnt flush due to me being a jackass and not getting the right glue stuff to hold it down
after that it should work perfect like before
if anyone wants to trade me a new screen for the i9000 screen or buy me a screen (lol) i would make a very detailed video (not happy with the way the first attempt turned out)
post itt or pm me if you have any questions
So you are saying it should work,but what about the software part,won't there be any problems?
Chrishas said:
So you are saying it should work,but what about the software part,won't there be any problems?
Click to expand...
Click to collapse
what are you talking about
thenotoriouspie said:
what are you talking about
Click to expand...
Click to collapse
about replacing a phone screen using a screen from another model,but of the same size,resolution
thenotoriouspie said:
3.balls. that ribbon cable is very very easy to break
Click to expand...
Click to collapse
and thats what I screwed up....what are my options now? Try again? dont think I can.
scrizz said:
FYI incase anyone else is looking for where to buy from.
http://www.globaldirectparts.com/Samsung-T959-LCD-Digitizer-p/smsng6085995.htm
Click to expand...
Click to collapse
did you see (Minimum order): 2
130448356330 check out this item on ebay
I really need help. I got my phone apart w/ the board for speaker and camera off and the front speaker off. I did not remove the haptic feedback motor yet. how the hell do you actually pry the screen off. i just don't see a way.
will the international galaxy s screen work for vibrant they hace same shape compared to captivate. And I9000s screen is cheaper than T959 screen (based on ebay price)

Disassembling the EPIC 4G?

Has anyone done it before? There is a video on youtube, but it only goes as far as the keyboard. I'm looking to get to the LCD to fix/replace it because of discoloration from water damage. Anyone thinks it's possible?
I remember a thread like this being made a while ago...if you're on a computer, just search and you should find it. I can't post a link, but I think the guy in that thread replaced it succesfully.
There was also alotta chatter about insurance covering it
Sent from my SPH-D700 using XDA App
Here's a tear down of the Epic 4G:
http://www.chipworks.com/en/technical-competitive-analysis/resources/recent-teardowns/2010/09/teardown-of-the-samsung-epic-4g-smart-phone/
Try asking a repair technician. The truth is, body repairs can be quite pricey - to the point where you might as well be getting a new phone in many cases.
I watched someone else take mine apart. There are an awful lot of little screws, but you can definitely seperate the case, the screen, and the actual guts in about 10 or 15 minutes.
DiGi760 said:
I watched someone else take mine apart. There are an awful lot of little screws, but you can definitely seperate the case, the screen, and the actual guts in about 10 or 15 minutes.
Click to expand...
Click to collapse
The question then is can you get it back together ;-)
Sent from my ext4 Epic 4G running Bonsai4all 1.1.3!
sauron0101 said:
Here's a tear down of the Epic 4G:
http://www.chipworks.com/en/technic.../teardown-of-the-samsung-epic-4g-smart-phone/
Try asking a repair technician. The truth is, body repairs can be quite pricey - to the point where you might as well be getting a new phone in many cases.
Click to expand...
Click to collapse
I had TEP with my BB curve and I smashed it [was REALLLLLLY angry at my gf...she wasn't worth the BB :'( ] and I took it to a corporate store, and he fixed the screen in front of my face and I walked right out lol but that was a couple years ago
Sent from my SPH-D700 using XDA App
The phone still works, I just wouldn't want to look at pictures or watch videos on it since the color is all messed up. It's been about 2 weeks since the accident and it's still going! I just want to study this just for reference just in case it does go out. The replacement cost $60 on ebay, so I'd definitely do that, especially when I don't have insurance with Sprint (I think it still costs more than DIY) and I don't think Samsung fixes water damage through its warranty.
Oh well.
Thanks for the link! I'll check it out!
being a technician at an indirect sprint store, its a pain in the ass to separate the LED screen and the glass itself. the very best way to do it is either go to a 3rd party sprint store that has a full service(repair) center and either have them do an exchange if the tech is a nice guy (considering its water damage) or replace the part (which would be free as long as you have TEP). PM me with more questions if you have them
kzn said:
Has anyone done it before? There is a video on youtube, but it only goes as far as the keyboard. I'm looking to get to the LCD to fix/replace it because of discoloration from water damage. Anyone thinks it's possible?
Click to expand...
Click to collapse
Yeah, I've done it at least 20-30 times now. It's EXTREMELY difficult to get the lcd out and you'll more than likely end up breaking your phone.
br//0k3/n said:
Yeah, I've done it at least 20-30 times now. It's EXTREMELY difficult to get the lcd out and you'll more than likely end up breaking your phone.
Click to expand...
Click to collapse
Yea, you're definitely right about the LED itself. It's close to paper thin and made of a glass type material. it will break if you try to get it out. it's glued pretty good.
flawlessbmxr said:
Yea, you're definitely right about the LED itself. It's close to paper thin and made of a glass type material. it will break if you try to get it out. it's glued pretty good.
Click to expand...
Click to collapse
I took mine apart, lots of screws. Honestly the hardest part was removing the back cover that goes over the motherboard. I used a very small flathead to pry up underneath where the little notches are on the side. There's a lot of clip points and 2 of them at the battery are very hard to get off. Once that's off, the rest is cake. Separating the screen was a non-issue, as mine was already broken/cracked.
just to chim,e in on this ancient thread. i used a guitar pick instead of a flat head. i thought a metal screwdriver would scuff and mar up the plastic cover over the board.
Another protip: the notches on the second to last plastic cover serve a purpose -getting that back half to snap onto the phone is a huge pain in the ass, - i put a flathead into the slits and pushed down and snap snap snap snap motherboard cover was back in and my battery case didn't bulge.
kzn said:
Has anyone done it before? There is a video on youtube, but it only goes as far as the keyboard. I'm looking to get to the LCD to fix/replace it because of discoloration from water damage. Anyone thinks it's possible?
Click to expand...
Click to collapse
I've replaced my LED screen before by myself, took a few hours. This video helped me.
http://www.youtube.com/watch?v=IeO89VGAPuU
zvonkorp said:
I took mine apart, lots of screws. Honestly the hardest part was removing the back cover that goes over the motherboard. I used a very small flathead to pry up underneath where the little notches are on the side. There's a lot of clip points and 2 of them at the battery are very hard to get off. Once that's off, the rest is cake. Separating the screen was a non-issue, as mine was already broken/cracked.
Click to expand...
Click to collapse
Is there a water sensor inside the phone, I've always wondered if the battery was the only place
Sent from my SPH-D700 using Tapatalk

How to replace just the glass lens on the at&t galaxy s3

Pretty much all you need in the title. I wanted to know how to do this mainly because it's cheaper then buying a lCD digitizer combo and because I can't find a guide anywhere else. Any tips and tricks on how to do this should be well appreciated and any guides. Thanks in andVance for anyone's help.
Sent from my SAMSUNG-SGH-I747 using xda premium
Backslash10 said:
Pretty much all you need in the title. I wanted to know how to do this mainly because it's cheaper then buying a lCD digitizer combo and because I can't find a guide anywhere else. Any tips and tricks on how to do this should be well appreciated and any guides. Thanks in andVance for anyone's help.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
I also have a cracked the screen, What my search result has come up with is the cost to replace the screen is ~$200CDN. Can you please keep me posted on what path you would be taking, might just follow
Replacing the glass from the actual screen is very hard and would require tons of technical know-how because the two are fused together.
Not recommended, even by experts.
Well I know it's extremely hard but I'm mainly looking for advise about it is all it decently help people out here.
Sent from my SAMSUNG-SGH-I747 using xda premium
Backslash10 said:
Well I know it's extremely hard but I'm mainly looking for advise about it is all it decently help people out here.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
it's not possible to do. period.
Really I thought I could be done but took a lot of waiting and just the right heat and pressure.
Sent from my SAMSUNG-SGH-I747 using xda premium
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
Nice
Op
http://forum.xda-developers.com/showthread.php?t=1904554
it is very possible I have done 4 of them already...
http://forum.xda-developers.com/showthread.php?t=1890708
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
hahahah.....owned, should really atleast attempt to find out if what you are saying has any evidence to support it, or rebut it
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
I've heard its possible, just EXTREMELY difficult to manage.. I wouldn't.
Its entirely possible, as the multiple video's have shown. Although i haven't done it to the SGS3 yet, i will be soon. Cracked my lens the other day, replacement in the mail. I have also changed the screen's on several iphones (at my job) which us a similar method of gluing. It is made to be difficult by design...to keep people from attempting it and opting to send it in for repair. Of course when you do this, through samsung anyways, you are being charged for the entire led assembly and not just the lens.
dntesinfrno said:
Its entirely possible, as the multiple video's have shown. Although i haven't done it to the SGS3 yet, i will be soon. Cracked my lens the other day, replacement in the mail. I have also changed the screen's on several iphones (at my job) which us a similar method of gluing. It is made to be difficult by design...to keep people from attempting it and opting to send it in for repair. Of course when you do this, through samsung anyways, you are being charged for the entire led assembly and not just the lens.
Click to expand...
Click to collapse
Good to hear you did it at your job with iphones. Any idea what glue they use to bond the glass to the digitizer? I have searched and searched and cannot find anything. I have done several S3 so far and this is the one ingredient lacking for a complete repair. In terms of what it feels like while removing the old glue; it seems to be silicone based the way it comes up, you can roll it into little balls, it's is tacky and has that rubbery consistency.
Unfortunately, no idea what adhesive they use. Personally i would attempt what YellowGTO did first and simply heat the existing glue and see how it holds. Normally this should be enough to do the job, as you can imagine the stuff if pretty tacky. Especially if the lens fits as tightly as his in the video, its doubtful it will fall out even with the slightest remaining glue. If for whatever reason there isn't enough to firmly hold the screen in place i've used small dabs of liquid tape where necessary, or the thin 3M double sided tape would work also i suppose. In this case i usually wrap the device in a towel or shirt or whatever you have laying around and set something with some decent weight on top of it, screen side down on a flat surface, overnight to give the adhesive time to setup properly.
dntesinfrno said:
Unfortunately, no idea what adhesive they use. Personally i would attempt what YellowGTO did first and simply heat the existing glue and see how it holds. Normally this should be enough to do the job, as you can imagine the stuff if pretty tacky. Especially if the lens fits as tightly as his in the video, its doubtful it will fall out even with the slightest remaining glue. If for whatever reason there isn't enough to firmly hold the screen in place i've used small dabs of liquid tape where necessary, or the thin 3M double sided tape would work also i suppose. In this case i usually wrap the device in a towel or shirt or whatever you have laying around and set something with some decent weight on top of it, screen side down on a flat surface, overnight to give the adhesive time to setup properly.
Click to expand...
Click to collapse
Sure the outer frame is enough in most cases to hold it on, thats fine. But there is a side effect once all the glue is removed off the digitizer. There will a micro gap between the 2 when the original glue is removed. If you press the new glass hard enough, ( for example cleaning fingerprints like I often do against my shirt ) and it touches the digitizer, the phone freezes. You must then power off the screen, sleep button and then press power again to bring it up and then it will work again. Seems to be a recalibration process going on.
Maybe these 2 posts should be merged and I would certainly read the post below. Much more good info here on the subject...
http://forum.xda-developers.com/showthread.php?p=33056057#post33056057
Yea, i've been following several threads about lens replacement, even before i busted mine (jinxed myself?). I'd much rather have to deal with a 15 second reboot over possibly damaging the LED or worse using an adhesive that may not be transparent. I can live with the air gap, or even the 'invisible' smudges on my personal device...although if i were going to do this for profit obviously that would be unacceptable. 20 dollars and an hour of my time vs 200+ for the whole assembly or 125 for an insurance deductable..i can overlook imprefections . It would be interesting to find out exactly what substance they are using though.
EDIT - Just for SnG's i googled 'mobile screen glue' and this was the first result. http://www.alibaba.com/product-gs/523467689/Optical_Clear_Adhesive_for_touch_screen.html?s=p
While i'm sure its not the only product out there for this purpose, if this is any indication it won't come cheap..
dntesinfrno said:
Yea, i've been following several threads about lens replacement, even before i busted mine (jinxed myself?). I'd much rather have to deal with a 15 second reboot over possibly damaging the LED or worse using an adhesive that may not be transparent. I can live with the air gap, or even the 'invisible' smudges on my personal device...although if i were going to do this for profit obviously that would be unacceptable. 20 dollars and an hour of my time vs 200+ for the whole assembly or 125 for an insurance deductable..i can overlook imprefections . It would be interesting to find out exactly what substance they are using though.
Click to expand...
Click to collapse
Agreed it would be nice to find out what type of glue.
The phone breaks so easy i am surprised I have not heard of a Class Action Lawsuit... :silly:
here are instructions on replacing just the glass/screen
[HOW TO] [TUTORIAL] S3 Replace Cracked Glass Screen w/ YouTube Video
i replaced my screen took me about 50 mins with 2 people
XeoNoX said:
here are instructions on replacing just the glass/screen
[HOW TO] [TUTORIAL] S3 Replace Cracked Glass Screen w/ YouTube Video
i replaced my screen took me about 50 mins with 2 people
Click to expand...
Click to collapse
Very very nice!! :thumbup::thumbup:
Sent from my SCH-I535 using xda app-developers app
marcustaz said:
Very very nice!! :thumbup::thumbup:
Sent from my SCH-I535 using xda app-developers app
Click to expand...
Click to collapse
JUst did an even EASIER replacement for a cracked camera lens. I purchased this part from ebay :
http://www.ebay.com/itm/Blue-Housin.../271099346918?ssPageName=ADME:L:eek:C:US:3160
1) Turn phone off
2) Take off battery cover
3) Remove battery, SIM card, and SD Card
4) remove about 8 screws to remove the middle back place.
5) Remove middle back place carefully (There are still tabs holding it secure)
6) Place new middle back in place
7) Screw down
8) Replace battery, SIM card, and SD card
9) Replace battery cover
10) Power up phone!!
Took all of 10 minutes total. Flawless fix on my AT&T Samsung Galaxy S 3
Gentlemen and OP please update your original post to include this video. This is NOT to promote myself but from all the comments and feedback everyone has stated it is the most detailed and informative on You Tube on the glass replacement procedure. I also have separate videos on shattered glass replacement. Thanks and good luck.

Screen Cracked Today :(

So....
I've NEVER dropped any of my phones, ever, as long as I've had cell phones. Well, dropped and it actually hit the ground. I've dropped this damn phone like 4x already, I think partially to do with it being so smooth and "slippery" to the hand.
Anyway, I dropped it once from about 6 feet in the air directly on the screen and NOTHING happened at all (except some very very minor dings to the frame itself) and light scratches to the screen protector. Today, I was trying to pull it out of my pocket at work when it slipped and fell (from about 2 feet from the ground) landing on the right side of the phone. My right hand (phone sits in right pocket) is in a brace due to a stress fracture I received at work, so when it slipped I couldn't catch it. I watched it fall, which was the worst moment ever lol. Since my work pants have slanted pockets, it fell behind me so I couldn't even attempt to put my foot under it to stop the impact.
Anyway, as I picked it up I honestly didn't expect to see anything. I pick it up, turn it over and it looks like there is a piece of hair right along the frame in the shape of a sideways "U". I went to brush it off and realized it had cracked!
It's a very small and almost non noticeable crack JUST before the digitalizer starts but I know it's there so it bothers me. I showed a few guys at work and nobody noticed it until I pointed it out.
Anyway, think its worth looking into getting fixed or just stick it out because it's so minor?
*sorry picture is so crappy, wife has a Lumia 710...camera sucks.
uoY_redruM said:
So....
I've NEVER dropped any of my phones, ever, as long as I've had cell phones. Well, dropped and it actually hit the ground. I've dropped this damn phone like 4x already, I think partially to do with it being so smooth and "slippery" to the hand.
Anyway, I dropped it once from about 6 feet in the air directly on the screen and NOTHING happened at all (except some very very minor dings to the frame itself) and light scratches to the screen protector. Today, I was trying to pull it out of my pocket at work when it slipped and fell (from about 2 feet from the ground) landing on the right side of the phone. My right hand (phone sits in right pocket) is in a brace due to a stress fracture I received at work, so when it slipped I couldn't catch it. I watched it fall, which was the worst moment ever lol. Since my work pants have slanted pockets, it fell behind me so I couldn't even attempt to put my foot under it to stop the impact.
Anyway, as I picked it up I honestly didn't expect to see anything. I pick it up, turn it over and it looks like there is a piece of hair right along the frame in the shape of a sideways "U". I went to brush it off and realized it had cracked! btw i use this case http://www.goballisticcase.com/products/samsung-galaxy-s-3-ballistic-sg-maxx-series-case makes my phone a bit thick but ive dropped it about 15 feet when i was on the roof the other day fixing the window. i pulled it out to check the weather cause it looked like it was going to rain well not rain more like hail. so i checked and instead of putting it in my pocket i missed and i just watched it slide off the shingles. and drop im like nooo its gonna be dead when i go pick it up. not even a scratch
It's a very small and almost non noticeable crack JUST before the digitalizer starts but I know it's there so it bothers me. I showed a few guys at work and nobody noticed it until I pointed it out.
Anyway, think its worth looking into getting fixed or just stick it out because it's so minor?
*sorry picture is so crappy, wife has a Lumia 710...camera sucks.
Click to expand...
Click to collapse
id personally get it fixed or fix it myself since only the screen and not the lcd. imagine if you ever drop it again even inches that "u" could probably be the cause of it expanding and cracking all over. well thats my opinion
Can't attach from the pc for some reason.
Sent from my SGH-T999 using xda premium
uoY_redruM said:
Can't attach from the pc for some reason.
Sent from my SGH-T999 using xda premium
Click to expand...
Click to collapse
the pic was attached to the first post
Dude, that sucks! Never wanted to see that happen to you man.
I have to agree though, if its doable for you, get it fixed. Once compromised like that its just gonna get worse most likely. Even just setting it down or bumping into something while its in your pocket could make it much worse.
Sent from my SGH-T999 using xda app-developers app
DocHoliday77 said:
Dude, that sucks! Never wanted to see that happen to you man.
I have to agree though, if its doable for you, get it fixed. Once compromised like that its just gonna get worse most likely. Even just setting it down or bumping into something while its in your pocket could make it much worse.
Sent from my SGH-T999 using xda app-developers app
Click to expand...
Click to collapse
I would say slap it into a bumper that will cover up most of it. But, you already said you know it's there, so that won't work. So, I guess I'd advise having it fixed.
Sorry to hear that.
Sent from my SGH-T999 using xda premium
---------- Post added at 11:53 PM ---------- Previous post was at 11:51 PM ----------
the ghost armor kit would cover that if applied right. I'll take a picture of mine if I can find a camera
Sent from my SGH-T999 using xda premium
uoY_redruM said:
So....
I've NEVER dropped any of my phones, ever, as long as I've had cell phones. Well, dropped and it actually hit the ground. I've dropped this damn phone like 4x already, I think partially to do with it being so smooth and "slippery" to the hand.
Anyway, I dropped it once from about 6 feet in the air directly on the screen and NOTHING happened at all (except some very very minor dings to the frame itself) and light scratches to the screen protector. Today, I was trying to pull it out of my pocket at work when it slipped and fell (from about 2 feet from the ground) landing on the right side of the phone. My right hand (phone sits in right pocket) is in a brace due to a stress fracture I received at work, so when it slipped I couldn't catch it. I watched it fall, which was the worst moment ever lol. Since my work pants have slanted pockets, it fell behind me so I couldn't even attempt to put my foot under it to stop the impact.
Anyway, as I picked it up I honestly didn't expect to see anything. I pick it up, turn it over and it looks like there is a piece of hair right along the frame in the shape of a sideways "U". I went to brush it off and realized it had cracked!
It's a very small and almost non noticeable crack JUST before the digitalizer starts but I know it's there so it bothers me. I showed a few guys at work and nobody noticed it until I pointed it out.
Anyway, think its worth looking into getting fixed or just stick it out because it's so minor?
*sorry picture is so crappy, wife has a Lumia 710...camera sucks.
Click to expand...
Click to collapse
Why mine is in an otter box ^-^
But I personally would just throw a case on it to prevent further cracking. Doesn't look too horrible from your picture. But as others already mentioned, it will crack even more easily since it's already started.
That's a known issue with the s 3. The screen is lifted a hair from the bezel. So the bezel bends into the glass at the edge (weakest point in glass) where other devices usually bend over the glass.
But good luck to whatever you decide!
Sent from my SGH-T989 using Tapatalk 2
Yeah it's not bad at all. And remember you can replace just the glass too. But i would wait for it to be more messed up before doing that
Sent from my SGH-T999 using xda app-developers app
Slap a good case on it and it should be fine for now at least.
Let's just hope that you don't drop it again to further increase the cracking.
An OtterBox Defender Case might be a good idea.
Very bulky, kind of pricey, but it will offer you the protection that you need.
Personally id be worried about further damage as is. Obviously the glass is weakened already, and while it may seem ok to wait until its worse before fixing, i have to disagree as im pretty sure this also makes the digitizer more vulnerable to damage as well.
How often have you seen or heard about devices that had a cracked screen causing the touch capabilities to break as well? One more drop or bump into the corner of a table where that crack is and you may not get anymore response at all.
I just think it potentially could turn into a much more expensive repair if not taken care of soon. Just not sure id personally want to risk it.
Its just my opinion is all.
Sent from my SGH-T999 using xda app-developers app
DocHoliday77 said:
Personally id be worried about further damage as is. Obviously the glass is weakened already, and while it may seem ok to wait until its worse before fixing, i have to disagree as im pretty sure this also makes the digitizer more vulnerable to damage as well.
How often have you seen or heard about devices that had a cracked screen causing the touch capabilities to break as well? One more drop or bump into the corner of a table where that crack is and you may not get anymore response at all.
I just think it potentially could turn into a much more expensive repair if not taken care of soon. Just not sure id personally want to risk it.
Its just my opinion is all.
Sent from my SGH-T999 using xda app-developers app
Click to expand...
Click to collapse
red you could just take it to tmo? or call Samsung it has to be under warranty but hey they'll do it and no screws up guaranteed. ad it will cost more than a do it your self. i saw somewhere that Verizon did for 100 with insurance, i assume tmo would close to that
Radio Shack has a service to replace your screen for $100. You would be without your phone for a couple of days, however.
I highly recommend the Otterbox Defender, and put all of my phones in one.
In March, while doing some climbing, I fell about 30 ft then tumbled down the side of a mountain. I had a Droid X in my pocket (in it's Defender), and the only damage to the phone was to the camera lens. Everything else about the phone was groovy. I was not in such great shape, as this was in the Arizona desert mountains, so there was no cushy landing whatsoever.
Defender FTW!
lokichim said:
red you could just take it to tmo? or call Samsung it has to be under warranty but hey they'll do it and no screws up guaranteed. ad it will cost more than a do it your self. i saw somewhere that Verizon did for 100 with insurance, i assume tmo would close to that
Click to expand...
Click to collapse
Sorry, i guess i just assumed we were talking about going by one of the diy guides i saw here not long ago. Pretty sure they had instructions for replacing only the glass, but anyway, if you have the full protection plan then it doesnt matter how bad its damaged. I believe the price about a month ago was $130.
Sent from my SGH-T999 using xda app-developers app
DocHoliday77 said:
Sorry, i guess i just assumed we were talking about going by one of the diy guides i saw here not long ago. Pretty sure they had instructions for replacing only the glass, but anyway, if you have the full protection plan then it doesnt matter how bad its damaged. I believe the price about a month ago was $130.
Sent from my SGH-T999 using xda app-developers app
Click to expand...
Click to collapse
we were but then i thought what if red messed up something by accident like we all might, wouldn't that void his warranty? if it didnt then im all in for diy, thats the only reason i said the tmo thing for safety measure. also red looked it up on ebay blue one with tools was 28 dollars and from usa.
Ok, i gotcha. I could be wrong but if you have the full protection plan i was under the impression that you could pretty much do anything and get a replacement. So if im right you can attempt the fix diy style and if unsuccessful then get it replaced. I would double check me on that though!
Sent from my SGH-T999 using xda app-developers app
DocHoliday77 said:
Ok, i gotcha. I could be wrong but if you have the full protection plan i was under the impression that you could pretty much do anything and get a replacement. So if im right you can attempt the fix diy style and if unsuccessful then get it replaced. I would double check me on that though!
Sent from my SGH-T999 using xda app-developers app
Click to expand...
Click to collapse
well i checked it here http://www.t-mobile.com/shop/addons...setProtection&tp=Svc_Sub_EqpmntProtnInsurance. and i assume it would fall under the damage one its pretty vague which is good for red. so your probably right doc
Yeah, I was considering the DIY route (its like $25 on eBay but you have to break your screen off basically which scares the sh*t out of me).
I do have the full insurance. I may have to go to T-Mobile just to see how much it would cost. I don't have the extra money, just got my car out of the shop. If anything, if the insurance covers it and isn't very much, I could just tough it out until it gets worse (if it does) and THEN take it in to the store for work.
uoY_redruM said:
Yeah, I was considering the DIY route (its like $25 on eBay but you have to break your screen off basically which scares the sh*t out of me).
I do have the full insurance. I may have to go to T-Mobile just to see how much it would cost. I don't have the extra money, just got my car out of the shop. If anything, if the insurance covers it and isn't very much, I could just tough it out until it gets worse (if it does) and THEN take it in to the store for work.
Click to expand...
Click to collapse
Hey what's up red.. so welcome to the "club"... I dropped mine two weeks ago and cracked the glass pretty good.. not too too bad but its has cracks that I can see n feel.. so n e way I got a guy that I trust on the g2x forums that I was thinking of sending mine to him.. would u like me to holler at him for you?
Sent from my GT-N700 using xda premium
Still lucky, mine cracked more severe while inside my pocket because I bumped into a desk :/
Sent from my SGH-T999 using xda app-developers app

Dropped Galaxy S3 in Bathwater

Hey everyone, so my buddy recently dropped his Galaxy S3 in bath water. He ended up buying a new phone thinking the phone was dead but he turned it on a few days later and it worked. Everything works EXCEPT the touch buttons next to the home button. I bought the phone off of him for $150 thinking I can fix it but as I research video and threads online.. it seems much harder than I thought. I know that soaking the phone in 99% isopropyl alcohol can fix a lot of water damage problems but I'm not sure if I should soak the motherboard in it as it's working fine other than the touch sensor buttons. Should I dip only a part of the front frame (where the touch sensors are) in isopropyl alcohol stopping right below where the LCD screen starts?
I'd like to change the frame as well since there are some scratches here and there along with the home button. It works but the button is scratched up a bit.
Do you guys have any advice for me? The phone is currently disassembled btw if that helps.
Could always download lmt launcher and not worry about it?
Sent from my SAMSUNG-SGH-I747 using xda premium
Or modify your build.prop to add capacitive buttons
Sent from my SGH-I747 using Tapatalk 2
Just use a ROM that has navbar settings and dont worry about the buttons. I dropped my old optimus t in water and yea it comes back to life , but the uncertainty of how long it will work is terrible. A few weeks after it happend phone screen flickering and it just died.
Best thing to have done was pull the battery and let it dry for two or three days
Sent from my SGH-I747 using Tapatalk 2
Lots of ways to just bypass the buttons all together. Like thwy all said use a custom ROM and nav bar. Just let it dry and leave it be. Good luck.
Oh and give lmt launcher a shot too
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
I would definitely research cleaning it properly.
The water residue will eventually crust up and cause connection issues or shorts.
CZ Eddie said:
I would definitely research cleaning it properly.
The water residue will eventually crust up and cause connection issues or shorts.
Click to expand...
Click to collapse
What do you think is a good way to clean it? Dip the main board in isopropyl alcohol?
I am a tech junky, the first thing I would do is take it 100% apart and clean every inch on the inside. Eventually the stuff inside of that phone will turn cruddy from the bath water. $150 for a SGSIII is a hella good deal, rip it apart and give it a good cleaning.
Thanks yeah I thought it was a great deal, I could've asked him to drop it less but I felt bad since he was my friend. Phone is brand spanking new and only used for 2 months.
I'm thinking about buying a new whole front piece (LCD, digitizer, frame) though.. what do you guys think? I can get it online for $230ish and not sure how much I can get for my existing front piece.
artluo100 said:
Thanks yeah I thought it was a great deal, I could've asked him to drop it less but I felt bad since he was my friend. Phone is brand spanking new and only used for 2 months.
I'm thinking about buying a new whole front piece (LCD, digitizer, frame) though.. what do you guys think? I can get it online for $230ish and not sure how much I can get for my existing front piece.
Click to expand...
Click to collapse
I would try to fix it before going for a new front piece. Getting that new front piece + the 150$ you already paid = the price of a brand new S3 on ebay.
If it's himidity keeping them from working, leaving the phone in a seeled bag of rice for a couple days can fix it.
If you have the $$$ laying around to do it I would say go ahead. It may help the resell value down the road. I can't stand this phone naked, it feels like a big wet bar of soap in my hands. I would preserve the $$$ spent and put it in an Otterbox Commuter.
I was thinking about making back the money by selling the original piece. Not sure how much I can get for that though. The only thing holding me back is replacing the silver bezel around the LCD. You have to remove everything and swap it over including LCD, glass, buttons, etc. Sounds like a big risk for someone like who who has never done this type of work before.
artluo100 said:
I was thinking about making back the money by selling the original piece. Not sure how much I can get for that though. The only thing holding me back is replacing the silver bezel around the LCD. You have to remove everything and swap it over including LCD, glass, buttons, etc. Sounds like a big risk for someone like who who has never done this type of work before.
Click to expand...
Click to collapse
Well if getting someone to do it for you doesn't cost much, could be something to look into.
Yeah currently looking for someone to do that for me. Not sure where to look... all these cell phone repair places want to replace the whole piece PLUS they keep your LCD for "recycling" which means they'll take my LCD, repair it and sell it to the next sucker for $200 something.
I'm in NYC btw.. so by any chance any of you know someone in the area who has experience doing this, please let me know. Thanks!
artluo100 said:
Yeah currently looking for someone to do that for me. Not sure where to look... all these cell phone repair places want to replace the whole piece PLUS they keep your LCD for "recycling" which means I'll take your LCD, repair it and sell it to the next sucker for $200 something.
Click to expand...
Click to collapse
Haha. Well mobiletechvideos.com is well known around here, could be an option. I dunno how he proceeds though.
BWolf56 said:
I would try to fix it before going for a new front piece. Getting that new front piece + the 150$ you already paid = the price of a brand new S3 on ebay.
If it's himidity keeping them from working, leaving the phone in a seeled bag of rice for a couple days can fix it.
Click to expand...
Click to collapse
+1
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Soaking it in 99% isopropyl alcohol right now. gave the mainboard a scrub down with a toothbrush about 1.5 hrs in. Also scrubbed the back of the touch screen, whichever resistors and chips I saw.
Fingers crossed.
Quick question.. how long should I let the parts dry after taking it out of the alcohol? It seems like alcohol evaporates pretty quick but the smell of it stays.

Categories

Resources