was getting ready to go to CM10 and wanted to wipe everything on my phone. went through and erased all user data, cache, etc... however, i also wiped the system partition. now i dont have a new zip to flash to install the firmware again and i cant mount it to USB to transfer one. has anyone seen anywhere to get the CM roms in tar or md5 format so i can just flash them from odin?
any other ideas would also be appreciated.
found an at&t stock rom so far (im using rogers so dont know if that is causing this error) when i go to flash it i get:
<ID:0/006> Added!!
<ID:0/006> Removed!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCALEM_I747ATTALEM_I747UCALEM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
ok just a followup.... it failed because i was trying to flash an AT&T rom. also, samsung-updates is slow as hell and my download failed 3 times. I used this in the end
d-h.st/oDF
just leaving this here in case anyone has the issue
Related
I was installing cyanogenmod but something soft-briked it so I went back and did the unrooting process but this time installed 4.4.2 instead of the older rom. After trying to root I learned that the stock rom I was on patched rooting away. Now I'm stuck and even trying to downgrade I get the following error in odin. All my searching I haven't found anything on how to fix this. Can someone help, all the guides on the forum do not work.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUAMDL_M919TMBAMDL_M919UVUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sbl2.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl3.mbn
<ID:0/006> rpm.mbn
<ID:0/006> aboot.mbn
<ID:0/006> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Guess I didn't need to do that, still was able to flash custom rom, thought i lost that ability. Now I only have to worry about the whole flag for warranty
.
Try getting another stock file, what I mean by another I mean find it from xdas s4 thread and a new version of Odin, preferably a older version
Sent from my SGH-M919 using XDA Premium 4 mobile app
I updated my i317M (Telus) via OTA and the next day it rebooted and went into boot loop.
I've tried flashing the phone with 4 different stock roms (from 4.1.2 to 4.4.2) but they all fail.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I317MVLBMA3_I317MOYABMA3_I317MVLBMA3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've tried flashing Philz Touch recovery but that fails as well.
I've tried to boot it into recovery mode but it shows a dead Android with error logs like "E:failed to mount"
Help?
goyagoyago said:
I updated my i317M (Telus) via OTA and the next day it rebooted and went into boot loop.
I've tried flashing the phone with 4 different stock roms (from 4.1.2 to 4.4.2) but they all fail.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I317MVLBMA3_I317MOYABMA3_I317MVLBMA3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've tried flashing Philz Touch recovery but that fails as well.
I've tried to boot it into recovery mode but it shows a dead Android with error logs like "E:failed to mount"
Help?
Click to expand...
Click to collapse
Try flashing with odin again but before flashing open the tar and remove the bootloader out of it.
Hi, thanks for the reply cnote.
Would the bootloader be sboot.bin or boot.img or both?
thanks again
edit: or rather, how do you remove the bootloader and remake the tar file?
goyagoyago said:
Hi, thanks for the reply cnote.
Would the bootloader be sboot.bin or boot.img or both?
thanks again
edit: or rather, how do you remove the bootloader and remake the tar file?
Click to expand...
Click to collapse
I believe it;s both. Just retrieve the tar file only.
sboot is the bootloader boot.img is the kernel .Have you tried the latest NH2 for your phone also maybe try using a pit file
The nh2 you will have to get from sammobile and the pit file can be found here http://forum.xda-developers.com/showthread.php?t=2609871
Also after odin is finished go into factory recovery and do a factory reset or its just going to sit at the boot screen
flashing pit file also gives an error :S
hi, today i was trying to downgrade from 4.4 to 4.3 but i think i messed up
anyways, im trying to flash "L900VPUBMK4_L900SPTBMK4_HOME.tar.md5" but i keep getting
on phone "sw rev.check fail. device:3, binary:2"
Code:
[SIZE="2"]<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006>
<ID:0/006>
<OSM> All threads completed. (succeed 0 / failed 1)[/SIZE]
on newer odin i get
Code:
[SIZE="2"]<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L900VPUBMK4_L900SPTBMK4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)[/SIZE]
also i can access download mode and cwm recovery.
can any one help me??? plzzzz any help is apreciated
If you're on the latest NE2 firmware it is impossible to downgrade back to mk4 due to Knox boot loader, download the NE2 tar and flash it thru Odin... good luck! You might have to look for a partition fix posted by jlmancuso somewhere in a buried thread...
I was able to flash http://forum.xda-developers.com/showthread.php?t=2541395 using twrp and abd. After that i downloaded mobile odin and installed stock mk4
Sent from my SPH-L900 using XDA Free mobile app
So I rooted my s4 mini i9195 and flashed aicp ver 10 and now I have no wifi, no mobile, no lte, the haptic feedback buttons don't work, no led, and my computer doesn't recognize the s4 mini unless I go into download mode. When I start up the phone it says something about something being wrong with the internal hardware of my phone but it's a brand new phone and I didn't have these problems before flashing this rom. I tried using odin to go back to stock and it fails at nand-write start. I tried loading a new pit and that fails too. I'm completely stuck now. I have no idea what to do. Can someone please help me?
How you flashed aicp?
I used cwm.
Here's what comes up on odin when I try to flash back to stock:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCOD3_I9195BTUCOD1_I9195XXUCOD3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Can you enter in recovery mode?
yeah, I can. I tried clearing caches and data and flashing aicp over again, it didn't work-in fact, for whatever reason the aicp rom isn't in my sd card anymore.
Try to flash a stock deodexed rom from here http://forum.xda-developers.com/showthread.php?t=2552363 using your custom recovery
the problem with that is I can't get anything from my computer to my phone because the phone doesn't pop up on My Computer and the phone doesn't give me any options when it's plugged in. It's only recognized when in download mode and trying to do anything in download mode doesn't seem to work.
Download direct to you phone and then move to sdcard or download to pc and than just using a card reader move rom to your sdcard and then try to flash
I can't download directly to my phone, I have no connection whatsoever on my phone.
Use a computer and a card reader ))
I'm going to get an sd reader later today. I tried flashing the modem and this is what I got:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUCOC2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NON-HLOS.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006>
<ID:0/006> Receive Response from boot-loader
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
What firmware did you have before flashing aicp?
It was android 4.4.2 touchwiz I believe but I don't know the details. The phone was up-to-date and it's I9195
Whatever try to restore to a stock rom by flashing a deodexed rom
so the rom flashed properly but I still didn't have mobile data or wifi or haptic feedback. I'm not really worried about the haptic keys because I can just use softkeys if necessary but the mobile data and wifi are an issue. LED worked when I shut the phone down to put it into download mode to flash the modem. Flashing the modem was unsuccessful:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUCOC2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NON-HLOS.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> Transmission Complete..
<ID:0/005> Now Writing.. Please wait about 2 minutes
<ID:0/005>
<ID:0/005> Receive Response from boot-loader
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
And the phone came up with red lettered "Secure Check Fail Modem"
Try to call *#06# And tell what you get
At least look here http://forum.xda-developers.com/gal...rom-aicp-6-0-kk-4-4-4-9195-919015-10-t2907258
IMEI 990004400585315 / 01
I looked on that thread but nothing about my issue is coming up.
<ID:0/005> Receive Response from boot-loader
<ID:0/005> Complete(Write) operation failed.
Does this mean that I should flash a new bootloader? I never unlocked knox because beyond voiding the warranty, I didn't think it would have any effect on flashing but I may be wrong?
Your phone is definitely a "i9195" and not a "i9195L"? Was your phone locked to a network?
I found this http://forums.androidcentral.com/sa...ot-flash-really-really-stuck-please-help.html try to do how is described in the last thread but remember that you have a 9195 not a s3
I just got this AT&T version of the Note 8 from a buddy, and am having a hard time flashing to CM13 6.0.1 with Odin 3.10.7. I have it rooted, but every time I try to flash the I467M_BNF5_BNF5.tar.md5 file, it fails. This is what I am getting:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> tz.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I feel like I am forgetting to do something trivial, so any help would be much appreciated
That has a locked bootloader. There is no custom recovery for that model. So roms are a no go on the ATT version.
Ah damn. I don't even want the phone part of it. I was trying to speed it up a little bit and get some customization options. I guess I can't be too angry because I only paid $75 for it and he had some pictures of his ex leftover on there. Thanks man