Broken screen. What are the options? - HTC One X

Bust the thing badly from only 3 foot onto hard surface.
Anybody had theirs replaced by htc or themselves or otherwise? Its cracked all over and the odd patch of yellow.
Ta slim
Sent from my HTC One X using XDA

my experience
Long story short, I have an att HOX with a broken screen that I purchased from eBay for cheap in addition to the global HOX that I am using to write this. The LCD was fine, just the glass was broken. After waiting for a replacement to ship from China, I waded into the intertubes and found several tutorials on screen repair for the HOX. After several infuriating hours I discovered something that none of the tutorials mention. The adhesive that bonds the LCD to the digitizer is very strong stuff and even with the liberal application of a decent heat gun, you stand a good chance of breaking the LCD while trying to separate it from the digitizer.
Your best bet is to purchase the display assembly and replace the entire thing. If you do decide to try and replace only the digitizer, you will need patience, lots of time(2 hours+), and some luck. Follow the directions but instead of trying to separate the two pieces in one go like they show in the tutorial, work your way in about a quarter inch or less at a time. Use the heat gun right next to where you plan to separate the LCD and then slowly work around from there. The longer it takes, the better. Just be careful not to overheat the LCD. A good rule of thumb is that if it is too hot to hold in your bare hand, you used too much heat.

This ^
If you try to only replace the digitizer.....you're gonna have a bad time

Related

Repairing Galaxy Nexus (Voume Button, USB Charging Front glass )

hello,
i recently got my hands on a galaxy nexus, Although it is working just fine it has a few problems:
the first being, the volume control button seems to have been taken off, i think replacing that with one found on ebay would do the trick.
this item i guess:
http://www.ebay.co.uk/itm/Samsung-i...arts_Tools&hash=item4d01f3f508#ht_1908wt_1270
Secondly the phone does not detect when usb is connected, or it is connected to a charger. HOWEVER it charges when the phone is off, but the screen does not go on. Will changing the usb charging board be the solution ? i am thinking something like this :
http://www.ebay.co.uk/itm/USB-Power...arts_Tools&hash=item27c572bbff#ht_4112wt_1037
The third and final problem with the phone is that the front glass is broken. HOWEVER the touchscreen works just fine and there are no spots on the LCD screen either. Will changing the front glass be easy ? Do any of you have any special tehniques or pictues/videos that can help ?
It is available on ebay. I have read around the internet that peeling it off is difficult and you need a heat gun, I am prepared to take that risk however i do not have any glue to use, could anyone recommend me the type of glue that is used to fix the glass ? it seems to be peeling off when i scratch it with my nail and has a rubbery texture
no one here to give their suggestions ?
No idea what kinds and of glue is down there, but there is also huge risk of tearing the screen if you want to separate the screen and glass.
I will recommend you to buy then entire screen though, although you could try doing it first.
Pressed from my Maguro
By far the hardest part will be replacing the glass. The glass is fused to the digitizer, and the whole thing is glued to the frame. The only replacements I've heard about were the whole assembly, not just the glass.
Check out http://ifixit.com for step by step instructions. I know they have one for the USB port, probably for the others as well.
Yes I agree with what others have said. Although it is very tempting to just buy the digitizer since the screen is working just fine, it is extremely difficult to separate them. Its not impossible though and if you have done it before on other phones then I guess you can spend a little on just the digitizer. It involves heating up the screen with a heat gun and slowly separting the two but thats a lot more easier said than done. Hopefully the entire assembly comes down in price though as its a pretty expensive part. Good luck!

[Q] Huge crack across screen!Need some advice.

Dropped my phone on asphalt today and got a big hairline crack across the screen . (Attached pics)
It really hurts cause i always baby this phone and just the rush to get to work and in my car, completely missed my pocket.
The screen is still responsive to touch and seems to be working normal thank god the lcd screen wasnt damaged and the digitizer didn't shatter.
Got a few questions t
1) just wanted to clarify that the digitizer lies ontop the LCD screen?
2) and that is all that needs replacing?(from damage seen in the pics)
3) also mine is branded just HTC(no carrier, so it's international GSM version?)
4) would it matter if i bought a replacement digitizer meant for the at&t version or not?
5) should be getting a one x that had some water damage and is no longer working. would the digitizer from this phone be a viable option for me to use as a replacement or should i just order the part online.( I really want it replaced fast and if i have to order the replacement it will take about a week to 2 weeks to arrive in my country
so apparently i can't attach any urls until i make 10 posts or i'd show u guys the part i wanted to order but its basically just a screen digitizer from ebay with tools needed for about $17.86.(is that cheap, good or expensive price considering the item + tools)
can you guys please search for it on ebay?the title of the post/part is Touch Screen Digitizer Glass Lens Replacement For HTC One X S720 + Free Tools
the link above is the item i'm looking to order for replacement. is it the right part i'm looking at?and would that be all i need or is there anything else i should add?also quality wise would it be top pick or are there any better options available?
Attached some pics also.Advice would be greatly appreciated.
You are unlikely to be able to separate the digitizer and lcd without damaging the LCD.
A water damaged phone may have a water damaged screen.
Search one of the other broken screen threads for more information.
I've replaced several screens on captivate.easiest way is get replacement(LCD+digetizer) from ebay,Google procedure.watch or read as many times as needed to feel confident to take apart phone.the hardest part is seperating LCD from phone(they use adhesive to secure LCD to phone).I used razor to carefully cut adhesive.
Most components are plug&play.just follow guide completely,u should be fine.
My LCD was $85 on ebay.good luck.
Sent from my SGH-I897 using xda app-developers app

[Q] Shattered glass

So, I shattered the glass on my Galaxy S3 today. It's pretty messed up (see the attached picture), but the touch works, even in the damaged areas. So it seems it's only the glass that needs to be replaced, with something like this:
http://www.ebay.co.uk/itm/Blue-Fron...K_Replacement_Parts_Tools&hash=item417515ee67
Correct?
Yep, goodluck. Replaced the same on my Galaxy Note 2. all good now.
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
1slow4G said:
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
Click to expand...
Click to collapse
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
MadsBen said:
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
Click to expand...
Click to collapse
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Actually the glass on an s3 is just that, glass. The digitizer is fused together with the LCD. However glass is glued to the LCD which can make it very difficult to replace. If you've never taken on the repair of a screen before then I would say you'll be more likely to break the LCD than not in your replacement of the glass. But again it is possible if you are very slow and very careful. As someone else mentioned though it's much easier to replace the whole assembly.
It didn't went well. I wasn't too carefull. In the bottom, the glass was too shattered, so when I tried to lift it, a piece with glue got stock and lifted the digitizer. So now that don't work. I'm not gonna spend £100-120 on a new digitizer, I'm gonna settle for my good old Nokia 6300i (and Nexus 7...) and wait for the Nexus 5.
I would wait for the n5.. gs3 is a dying trend already.
Its hard like everyone said , if your really gunna do it watch videos online and be prepared. If you know anyone that has done it successfully ask for help or tips
ouch didnt see u tried it already
the same happened to me on my wife's white sgs3 trying to be the savior of the day turned out to be an expensive digitizer replacement of $200 instead of the $8 glass replacement. I rushed the glass removal and cracked the lcd screen. I could have ordered one on ebay for $100 but wife needs the phone the next day so i decided to get it repaired locally.
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
My 2 cents
bidibull14 said:
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
Click to expand...
Click to collapse
Wanted to warn that changing the glass is not for everyone. It takes patience and zen. If you rush it, you will likely break LCD and spend even more $$$ that you would have otherwise. Also following notes:
1. Watch at least a couple of youtube videos before starting.
2. Heavy duty heat blower works much better than a hair dryer. Of course, don't go crazy, as it's possible to melt the phone with it
3. S III has a wire at the bottom (the one which goes to the buttons). If you damage it, you will need to replace whole LCD, there is [almost] no chance you will be able to fix this wire. So, always start removing glass starting with the top of the phone
4. Heavily cracked glass is hard to remove, as it crumbles. To make it easier, a) put a scotch tape on top of glass, so that the small pieces stick to it, and b) use a lot of heat
5. Everybody advises to use plastic tools, personally I used swiss army knife with high level of success, and never had a problem scratching LCD. Your mileage may vary, but using metal blade certainly makes life much easier, especially in heavily cracked glass situation.
6. If you do use blade, it often is enough to get blade just a little bit under a glass, and then simply apply heat. Big chunks will unglue all by themselves.
7. Remember, that failure is always an option. Don't use it on the phone, if you know that you desperately need it working right this day, if you don't have a plan B.
1slow4G said:
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Click to expand...
Click to collapse
same freezing issue on mine... apparently the hardness of Gorilla2 is much greater than the knockoff glass replacements. The replacement glass on ebay and kijiji may not be authentic and that is why it bends slightly when pressed harder (in fact mine cracked completely when I applied too much pressure)
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
hani93 said:
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
Click to expand...
Click to collapse
I've heard about that glue too. I'm considering switching mine, because when I repaired I reused the glue of the original glass, and know I had dust between the glass and the lcd -.-
My concern is about the uv light, don't know if we could put in the sun to substitute it.
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
m1batt1 said:
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
Click to expand...
Click to collapse
it's not that hard to remove factory gle there..
for example, i removed mine, by rolling the glue with fingers.
just make sure, that you don't apply too much pressure to lcd.
and after that, clean up lcd form dust/fingerprints, and you are good to go.
and for removing glass, i used usual/ stronger kitchen knife (attached picture).
i replaced my glass 3 months ago.
i use normal hair dryer to remove glass and glass comes out almost as whole except for small broken pieces.
i think my scratch guard help in that.
i didnt use any additional glue or uv light.
nonresponsive screen is issue but only when you press too hard and press of power button resolve this issue.
but whole process of replacing galss took 2hrs

[Q] Screen Shattered

Hey All.
Been using nexus 7 2013 since last 2 years. My nephew dropped it and the screen cracked from the side. The device is working fine. The touch doesn't work at the the area of the cracks on the top right, and a few other places. But works everywhere else on the screen. My question is what has to be replaced, the digitizer or the entire LCD. My personal diagnoses is only the upper glass needs to be replaced. Please advice further!
Digitizer is for $15 and the whole thing is for $50. What has to be replaced and how to find out?
Please see the pictures and help me please
Get the whole thing. Replacing only digitazer is very difficult and compromises the tablet's construction.
no_cannabis said:
Get the whole thing. Replacing only digitazer is very difficult and compromises the tablet's construction.
Click to expand...
Click to collapse
agree with you
barriecary said:
agree with you
Click to expand...
Click to collapse
how much cost to replace?
I did it, two times, buy the glass+lcd+digitizer combo, you can find it at ~ $40
It takes 10 minutes to disassemble the tablet and 1h+ to separate the glass from the frame, the glue is very strong and the melting point is so high that you can melt the frame when trying to separate. Even doing this you will have to scrap the glue and zillions of microscopic bit of glass embeded in the glue. It's doable of course, but be patient!
I bought the screen + digitizer from Aliexpress about $20 last month
This was the guide I followed: https://www.youtube.com/watch?v=hAlNuGrGDuU
I didn't have heat gun or other thing, I just scratched the whole screen away from frame, took me couple of hours to completely replace the screen, but works nicely. This was the first time ever I've replaced a screen.
Just make sure you have double sided adhesive tape before you start, about ~3mm or so. My replacement screen didn't include that adhesive so I had to buy it separately.
well done..patience is the key, so id be not very good at it..haha..touch wood ive never dropped any of my tablets/mobiles, hopefully the cases i always put on would cushion any blows, i bought a used nexus 7 2013 and although cosmetically its in great shape, the lcd is showing blue blobs, like ink leakage..stuck pixels maybe, but i dont think you can just do the lcd change, the whole front would need buying which is pointless as i only paid £45 in the first place.. but im so impressed with it performance wise, i got a samsung t280 in the latest sale, returned it after 3 days, the chip inside was shockingly rubbish..

Should I replace touch screen digitizer alone (without LCD)?

I recently shattered the front glass on my Z1C. The display still works, but I get so many random ghost touches that it is unusable. Just wondering if anyone here has replaced the screen digitizer by itself rather than buying the digitizer + LCD screen together. Obviously it would be more difficult, however many posts about replacing both have mentioned the lower quality of the LCD image. Since my LCD still works, it would seem like a better option to use the stock one rather than a cheap knock-off. Not to mention it would be a little bit cheaper (I saw a kit which included glue, UV torch, tools, cleaner, and the digitizer for around $18 US). But on the other hand, with the added complexity comes additional risk that I will screw it up and end up worse off than just living with a duller display.
I’m still on the fence about which way to go here. Quality is subjective, so maybe I’m worrying over nothing and the new LCD would be good enough for me. I’d really appreciate your opinions.
Thanks!
Replace all.
I would suggest you to replace the LCD and digitizer completely. I broke mine in December last year. A small glass crack along the power button side made the top half of the digitizer stopped working. The LCD was fine though. I had to connect a wireless mouse to make a backup, copy some stuffs and use my old phone, while the replacement part came. Bought mine from Witrigs.com for $42 including front housing adhesive and shipping. Repairing was easy. Just heat the front part, lift it carefully. Swap the old part for the new one.
But like you I wanted to separate the glass digitizer from the LCD first. After several attempts removing the glue and the glass, the LCD had burnt spots. Maybe I applied a little too much heat in trying to remove the glass. And the broken glass left some permanent scratch marks on the LCD even after cleaning.
In all, trying to separate the LCD and glass has become very hard since last year. I've been repairing phones and tablets for years, mainly broken LCD or glass or both. From my experience, its better to change the whole part now.
Wish you good luck for the repair. Lets hope your phone lives again!!
same here. its very hard without professional stuff to change the display glass without damaging the touch under it. best way is to buy a new "complete" display module (glass, digitizer, touch) so that u only have to press the felx ribbon to ur phone. then using the glue stripes to fix it (using a hair dryer makes it easier to press it in).
Before the installation test the functionality
Hi there!
Can someone trustfully confirm, that witrigs.com is a good source for parts?

Categories

Resources