My problem is I can't access QPST, after I made a change to my ppp config...the weird part is, Odin works, and I can reset the phone in download mode. But when it comes back on, it keeps swithing into airplane mode...also, its giving an error message.TI have all the proper drivers installed...and the phone works...I just cant think of away to get back into my DIAG MODE so I can do programing. I have another post with more detailed info....I'm reposting here because I cant post in the development section yet.....
So...what error message is it giving you? What rom are you on? What change did you make to your ppp config? And are you using the proper modem for your build?
rom is the 2.1 stock..i didnt get a chance to change that yet...In ppp config, I changed my NAI Tethered..from boost to blank..then i changed the user ID to blank.... and I copied the HA AND AAA's from profile 0 & 1 to the epic from th Tp2....when I wrote to the phone it reboted.....as far as the modem I'm not sure but I think is odin..i downlaoded on it and tired to restore everything to stock but that doesnt work...
the message error says Sorry! The process com.android. phone has stopped unexpectedly. Please try again.
ummmm try a hard reset, or data restore... see if that resets the information that you changed, cuz the information you deleted and changed is the sprint programming so you might not have signal for data, atleast when i do my toroubleshooting i see the HA's and user name and stuff
I dont think the issue is with the ppp config..Its the NV items I wrote to the phone in cdma workshop...when the phone reset, and came back on it stopped reading the port. the phone can connect in pda but you can not acess cdma or qpst from there..I cant change back the NV items
Friends- I am facing a strange problem here. While i connected Sprint S3 for the first time, i was able to connect it to WS 2.7 by latching to the com port after getting in diag mode(rmnet+dm+modem). I was even able to unlock the set by entering samsung default password (while it was not getting spc unlocked) and then flashed cdma operator parameters. After the phone got reset, i checked for prl in the handset which was changed, which meant i was able to flash the parameters.
But then after that, i am able to connect my phone to ws2.7 by latching to the com port, but when i go to read or enter spc/etc, it gives an error "Failed... Phone does not answer". I tried removing the phone and connecting it again, changing the port, reinstalling drivers, but same issue. Request help from gurus..
I am using a HTC One V CDMA (Virgin Mobile USA) in India on Reliance CDMA network. The phone was flashed to Reliance and everything is working fine ie I can make/receive calls/sms etc. 1x / EVDO credentials have already been written to the phone.
Now the issue is that I am not able to enable data or the data connection doesn't get enabled automatically. When I try to enable data it says "Disconnected because service is unavailable". But if I press the "Activate this device" button in the settings section, an activation screen 1..2..3 comes up, then wait for 3-4 sec, the 3G symbol gets displayed meaning its able to make a data connection. Now if I go back to the settings page and enable data it successfully connects, and I am able to access internet at EVDO speeds. But after some idle time, the data connection is automatically disconnected and to reconnect I need to repeat the above process. Even if I intentionally disconnect data and try to reconnect, it doesn't happen and I need to go through the "Activate this device" process.
I believe some sort of initialization is missing which is done during the "Activate this device" phase and hence I am able to connect. What could be the reason for this? Is it some setting/configuration that needs to be enabled?
Please pour your valuable tips to resolve this issue.
Thanks
Fixed the issue with auto connection of data, not sure what fixed it exactly, but here are the last changes that I made after which it started working.
You need to use the tool QPST (I used version 2.7.378, an older version didn't work) for this.
In the M.IP tab, disable all profiles except profile 1
Then edit profile 1 and make changes (check attachment)
Then in RmNet tab enable auto connect for device 0 and 1.
After that
PPP Config --> Um --> Enter user/pass as "net" (Req Pw enc should be unchecked)
PPP Config --> AN --> Enter the EVDO credentials given by the MEID registrar (Req Pw enc should be unchecked)
Please note that I got it working merely by trial and error and some of the above changes may not be required and I am not even sure why they are necessary , but with the above configuration I am able to enable data without any problem.
iamvarkey said:
Fixed the issue with auto connection of data, not sure what fixed it exactly, but here are the last changes that I made after which it started working.
You need to use the tool QPST (I used version 2.7.378, an older version didn't work) for this.
In the M.IP tab, disable all profiles except profile 1
Then edit profile 1 and make changes (check attachment)
Then in RmNet tab enable auto connect for device 0 and 1.
After that
PPP Config --> Um --> Enter user/pass as "net" (Req Pw enc should be unchecked)
PPP Config --> AN --> Enter the EVDO credentials given by the MEID registrar (Req Pw enc should be unchecked)
Please note that I got it working merely by trial and error and some of the above changes may not be required and I am not even sure why they are necessary , but with the above configuration I am able to enable data without any problem.
Click to expand...
Click to collapse
Thanks for the above method .. Did you use this method after loading the NVDump file given by the registrar ? ... ALso when i edit the UM and AM feilds and issue write to the phone its showing as the phone has a read only NV ITEMS.
yakaaithiri said:
Thanks for the above method .. Did you use this method after loading the NVDump file given by the registrar ? ... ALso when i edit the UM and AM feilds and issue write to the phone its showing as the phone has a read only NV ITEMS.
Click to expand...
Click to collapse
Well, I had loaded the NVDump earlier, but as I had mentioned it would connect first but if you disconnect or get disconnected it wouldn't reconnect.
Check if the SPC is correct, cause I never got any error like that.
iamvarkey said:
Well, I had loaded the NVDump earlier, but as I had mentioned it would connect first but if you disconnect or get disconnected it wouldn't reconnect.
Check if the SPC is correct, cause I never got any error like that.
Click to expand...
Click to collapse
OP, I am taking a HTC One V for my dad and plan to use it with reliance, could you please tell me what I need to do ?
I already unlocked and rooted the phone. Do I just walk into a reliance store or do something more on computer etc before going there ?
experx said:
OP, I am taking a HTC One V for my dad and plan to use it with reliance, could you please tell me what I need to do ?
I already unlocked and rooted the phone. Do I just walk into a reliance store or do something more on computer etc before going there ?
Click to expand...
Click to collapse
You are talking about Reliance CDMA right?
If yes you need to get the MEID registered, will cost you about Rs 500. Reliance store guys will not do it, have to get it done through some 3rd party provider.
It says Read only NV Items for me too
2kool2btrue said:
It says Read only NV Items for me too
Click to expand...
Click to collapse
That's fine. Its only for one particular NVITEM. Just ignore it.
Hello varkey bhai,
Please Help me with the problem.
1. my meid is registered with reliance.
2. my prl is 00005
3. i am using the handset since 10 months.
4. evdo is also activated on my number.
But i am just getting 1x speeds.
Only thing i feel, i am missing out is on the username,Password,NV file,akey etc.
I have not received the above details from my reigstrar
Can u please guide me how this can be done to start evdo speeds.
Thanks in advance
vakubhai said:
Only thing i feel, i am missing out is on the username,Password,NV file,akey etc.
I have not received the above details from my reigstrar
Click to expand...
Click to collapse
Without the correct EVDO credentials, you won't be able to get EVDO speeds. You need to check with your MEID registrar.
NV dump is not really required and the same can be configured manually if you have the credentials as I have described above. Since you are able to make and receive calls, it looks like the Akey is already set.
so that means if i dont get the credentials from the registrar EVDO can never be started on this handset??
iamvarkey said:
Without the correct EVDO credentials, you won't be able to get EVDO speeds. You need to check with your MEID registrar.
NV dump is not really required and the same can be configured manually if you have the credentials as I have described above. Since you are able to make and receive calls, it looks like the Akey is already set.
Click to expand...
Click to collapse
vakubhai said:
so that means if i dont get the credentials from the registrar EVDO can never be started on this handset??
Click to expand...
Click to collapse
You could check with some other person who does MEID registration, maybe they can retrieve the credentials. But without it, EVDO will not work.
i have an htc droid incredible and i am facing the same problem as mentioned above are the steps above same for my phone also
vikisharma said:
i have an htc droid incredible and i am facing the same problem as mentioned above are the steps above same for my phone also
Click to expand...
Click to collapse
Try it out. It should work.
NVITEM Dump file
iamvarkey said:
That's fine. Its only for one particular NVITEM. Just ignore it.
Click to expand...
Click to collapse
Hello iamvarkey,
i have a sprint htc one that i have flashed but still dont have signal for voice and data. will the nv dump file help resolve this issue and how can i get it.
thanks
jewelman said:
Hello iamvarkey,
i have a sprint htc one that i have flashed but still dont have signal for voice and data. will the nv dump file help resolve this issue and how can i get it.
thanks
Click to expand...
Click to collapse
Simply by loading the Reliance PRL file, you should have voice signal, if not you are doing something wrong.
iamvarkey said:
Simply by loading the Reliance PRL file, you should have voice signal, if not you are doing something wrong.
Click to expand...
Click to collapse
i had done that but didnt work. the phone was sent to me without activating it first with sprint, can this affect it
jewelman said:
i had done that but didnt work. the phone was sent to me without activating it first with sprint, can this affect it
Click to expand...
Click to collapse
I don't think that would be a problem.
Make sure you are using the right PRL file.
No above steps required.
You must have flashed NV Dump already.
Your phone must be activated via *228 already.
Just perform below mentioned steps :
1) Put your phone in Diag Mode by dialing ##3424#
2) Get HTC Diag Mode driver if you don't have it already
3) Download DFS Demo version from DFS Website
4) Connect your phone with DFS, send SPC
5) Now, go to Programming tab -> Data ->
6) Click Read
7) At PPP tab, write "net" (without quotes) to SIP NAI, UID, Pwd field.
Restart the device and here you go, your device would get connected to internet instantly.
keval32 said:
No above steps required.
You must have flashed NV Dump already.
Your phone must be activated via *228 already.
Just perform below mentioned steps :
1) Put your phone in Diag Mode by dialing ##3424#
2) Get HTC Diag Mode driver if you don't have it already
3) Download DFS Demo version from DFS Website
4) Connect your phone with DFS, send SPC
5) Now, go to Programming tab -> Data ->
6) Click Read
7) At PPP tab, write "net" (without quotes) to SIP NAI, UID, Pwd field.
Restart the device and here you go, your device would get connected to internet instantly.
Click to expand...
Click to collapse
Keval,
I recently bought a HTC One E8 and am using Reliance CDMA on Slot-1 and facing this issue.
Would the steps jotted by you help me?
Thanks,
Vinay