Develop Bugs

[Q]Laggy after flashing new Rom/Kernel

Hello,
I have just flashed AOPK 4.0.3 and Franco 4.0.3 to my GN but it looks abit more laggy and the battary looks like its draining abit faster, is that due to the fact its less then a day on the device? will it be better? can someone explain how to use the Performence tool on this rom ?
Max Cpu/Min Cpu and Scaling governer
Voltage Control
Thx

1) Try a factory reset. Some times there are bits and pieces left over from your previous ROM. Standard ROM procedure.
2) if Step 1 doesn't work, reflash everything. Sometimes a bit here and there is off, resulting in a bad flash. It will only give you problems when those bad bits are needed, causing crashes or battery eating program loops.
3) If that doesn't work, redownload the ROM/Kernel. Verify the MD5 and flash that.
4) If you're having the exact same problem when trying all 3 steps, then it might be a ROM problem and you should contact the ROM dev and explain the problem and ask what you need to do to help him. However, it might not be a problem the dev can fix. Sometimes you have a phone that doesn't work with ROM X when the cell network equipment for Carrier Y in your area is provided by Company Z. Try another ROM/Kernel combo. Eventually, you will find something for you.

vitalero said:
Hello,
I have just flashed AOPK 4.0.3 and Franco 4.0.3 to my GN but it looks abit more laggy and the battary looks like its draining abit faster, is that due to the fact its less then a day on the device? will it be better? can someone explain how to use the Performence tool on this rom ?
Max Cpu/Min Cpu and Scaling governer
Voltage Control
Thx
Click to expand...
Click to collapse
The lag may be caused by something as simple as your phone does not like the default setting for either the governor or the max cpu frequency. I would recommend to lower the max cpu setting and see if that helps. If not, try increasing the min cpu setting or change the governor to Ondemand or Performance and see how it works. If none of this helps, try a different kernel.
Good luck

Something that i did notice is the now and before the flashing my ram is still 300 only available and 370 used, is there a way to make it lower? thats after reboot...
Another questions is, my friend have a SG2 with Lite'ning rom on it, and his colours are AMAZING he still doesnt have ICS but he runs faster then my fresh nexus, how can i atlist make my colours as vivid as his? Thx

Bumped once, can someone answer please?
my friend's SG2 also show 850mb ram total and by a press of a butten it clears to 600 ram free and 250 working. why our phone shows only 750 and on my only 300 free all the time and 350 buzy while nothing working...

[Help] Lots of freezes and crushes after updating to 4.0.5

Hi,
I've had my Archos G9 80 updated to the latest android official 4.0.5 from and since then i'm expriencing lots of crushes and freezes. I'm getting them randomly with no specific app working.
Also, i have tried to do full formats (Android + Data), and still having same issues.
Does anyone have any idea what else i can try?
Thanks.

I had lots of freezes too (not only with the latest firmware). They seem to be gone since I changed the CPU govenor from "hotplug" to "interactive". I'm not sure yet that it was the reason, but try it and let us know if it helps.

DeeDroid said:
I changed the CPU govenor from "hotplug" to "interactive".
Click to expand...
Click to collapse
how this is done? Ι have the same problem!

africa_twin said:
how this is done? Ι have the same problem!
Click to expand...
Click to collapse
Yes, can this be done from the phone itself? Within the ROM?

You can set this in any tool that is intended for overclocking. I don't overclock, I only changed the Govenor.
I use "SetCPU". ("No-frills CPU Control" should do the same.)

So does this have any other effects on the phone?

RichWPX said:
So does this have any other effects on the phone?
Click to expand...
Click to collapse
Nothing too serious. Your CPU is clocked dynamically so it doesn't run full speed when there is nothing to compute(save energy). To my understanding the govenor is basically a policy to manage how quickly the frequency steps up/down on changing CPU load. So "powersave" is supposed to save energy but make the system a little less reactive than "interactive" Governor for example. I think I read somewhere "hotplug" deactivates the second core on low load situations, I suspect for some strange reason my device might have crashed sometimes on trying to wake up the sleeping second core. Well maybe I'm wrong, that's why I'm interested if it helps others.
I didn't notice any change in battery lifetime, mostly it's the display anyway that drains the battery. Everything is running well, battery lifetime is great too and no crash/freeze at all since i changed that setting and it crashed almost every damn day before, no matter if it was Honeycomb or ICS.

I downgraded the device to 4.0.4 and since then, no crushes.. I guess for some reason 4.0.5 isn't stable on my device.. ill stick with this version unroll they get another one out..
To downgrade, just install official update file of the version you want to upgrade to..

DeeDroid said:
Nothing too serious. Your CPU is clocked dynamically so it doesn't run full speed when there is nothing to compute(save energy). To my understanding the govenor is basically a policy to manage how quickly the frequency steps up/down on changing CPU load. So "powersave" is supposed to save energy but make the system a little less reactive than "interactive" Governor for example. I think I read somewhere "hotplug" deactivates the second core on low load situations, I suspect for some strange reason my device might have crashed sometimes on trying to wake up the sleeping second core. Well maybe I'm wrong, that's why I'm interested if it helps others.
I didn't notice any change in battery lifetime, mostly it's the display anyway that drains the battery. Everything is running well, battery lifetime is great too and no crash/freeze at all since i changed that setting and it crashed almost every damn day before, no matter if it was Honeycomb or ICS.
Click to expand...
Click to collapse
Thanks! And I have notices ICS is not as snappy as GB was... I mean GB flew! Swiping the screen, it feels a little off now.

RichWPX said:
Thanks! And I have notices ICS is not as snappy as GB was... I mean GB flew! Swiping the screen, it feels a little off now.
Click to expand...
Click to collapse
GB? Gingerbread? Guess you mean Honeycomb. Anyway, I experienced ICS to be much better.

DeeDroid said:
I had lots of freezes too (not only with the latest firmware). They seem to be gone since I changed the CPU govenor from "hotplug" to "interactive". I'm not sure yet that it was the reason, but try it and let us know if it helps.
Click to expand...
Click to collapse
changing govenor from "hotplug" to "interactive" seems to help against random freezes. 4 days without problems until now i had freezes with ics, but never with honeycomb.
device: archos 101g9
[ROM] Archos ICS - Firmware 4.0.5(4.0.3) - ROOT & BUSYBOX , Only for SDE (thanks surdu_petru)

DeeDroid said:
I had lots of freezes too (not only with the latest firmware). They seem to be gone since I changed the CPU govenor from "hotplug" to "interactive". I'm not sure yet that it was the reason, but try it and let us know if it helps.
Click to expand...
Click to collapse
That seems to be my problem too. Setcpu requires root. is there a very easy way to do this, just to run this setcpu? There used to be a z4 tool, but can't seem to find it anymore.
Edit I see that I need superoneclick. Will temporary root suffice or will I need permanent root to change the governor setting.and keep it so.

Unfortunately all know temp root variants tend to brake things- im Honeycomb sound, in ICS 3d driver.
The only real option is to enable SDE and use custom firmware.
As for freezes- try reinstalling apps. Direct upgrade from Honeycomb does not work for all
tapatalked from Xperia Arc S

DeeDroid said:
GB? Gingerbread? Guess you mean Honeycomb. Anyway, I experienced ICS to be much better.
Click to expand...
Click to collapse
I have the same experience. Hc was laggy and slow. Ics is much faster and smoother.
Sent from my ARCHOS 80G9 using Tapatalk

gen_scheisskopf said:
Unfortunately all know temp root variants tend to brake things- im Honeycomb sound, in ICS 3d driver.
The only real option is to enable SDE and use custom firmware.
As for freezes- try reinstalling apps. Direct upgrade from Honeycomb does not work for all
tapatalked from Xperia Arc S
Click to expand...
Click to collapse
sorry for the n00b question, but SDE stands for ??? S ? Develeper Edition ?
Will "Superoneclick" not root my device ?

sbtwister said:
sorry for the n00b question, but SDE stands for ??? S ? Develeper Edition ?
Click to expand...
Click to collapse
Special Developer Edition
sbtwister said:
Will "Superoneclick" not root my device ?
Click to expand...
Click to collapse
No, it won't. Gen9 system layout is different than for most other devices

hey, back to topic
5 days without freeze with govenor "interactive". i witched back to "hot plug" this morning and had to reboot my tablet 2 times today. for my case, "interactice" seems to help against random freezes.

mines performance intstead of interactive... experienced some freezing n interactive..

Man I'm really pissed.
Yesterday I had to hard reboot 7 times
Sent from my X8 using xda premium

hmm,
sounds not good. archos stands not for high quality i guess. we get what we pay . i had an archos 101g8, now a 101g9 and trouble with hard-/firmwares since 2010. i think, this was the last one - no furthermore advantures
@IrishStuff09: you did reformat for ics or upgrade from honeycomb? the best way is to start from scratch and skip upgrades.

[Q] Does anyone else's A100 slow down

Does any one else's a100 become super laggy after a few minutes of being on.. I am running the latest flex reaper I even overclock it all the way but I get this huge lag after the first few minutes of being on.. anyone else experience this or have a fix for this?

Crimson Ghoul said:
Does any one else's a100 become super laggy after a few minutes of being on.. I am running the latest flex reaper I even overclock it all the way but I get this huge lag after the first few minutes of being on.. anyone else experience this or have a fix for this?
Click to expand...
Click to collapse
I do not experience this issue. When you flashed the rom, did you do a clean install? Have you formatting the device?

Yup.. I format everything.. I use the touch recovery and just use every option that it provides and wipe everything.. It even does it when there is nothing installed. I usually delete almost all the useless system apps that I don't use like the google music app and all of the ones civato provides... I even change the animation settings to .5 in the developer section.. should I turn them off all together?

Crimson Ghoul said:
Yup.. I format everything.. I use the touch recovery and just use every option that it provides and wipe everything.. It even does it when there is nothing installed. I usually delete almost all the useless system apps that I don't use like the google music app and all of the ones civato provides... I even change the animation settings to .5 in the developer section.. should I turn them off all together?
Click to expand...
Click to collapse
The animations should not have anything to do with it. Does this only occur on that rom? Have you tried other roms and experienced that issue?

not many other roms out there.. I have used stock and his.. had the same issue on both.. Also happens on my brother's a500.. it usually happens when unlocking and going into any app.. it sits there for a few seconds and then opens whatever it is i opened

Crimson Ghoul said:
not many other roms out there.. I have used stock and his.. had the same issue on both.. Also happens on my brother's a500.. it usually happens when unlocking and going into any app.. it sits there for a few seconds and then opens whatever it is i opened
Click to expand...
Click to collapse
This is starting to sound like a hardware issue. Before that is concluded, you could:
- Make sure the governor is not set to "conservative"
- Try a clean install of CM9
If the problem still arises, its most likely a hardware issue.

I'm using the OC kernel and have it to 1500.. I also always leave it on performance.. I figure it would kill my battery life but I don't use it much.. and i tried cm9 also.. too many issues as of right now

Crimson Ghoul said:
I'm using the OC kernel and have it to 1500.. I also always leave it on performance.. I figure it would kill my battery life but I don't use it much.. and i tried cm9 also.. too many issues as of right now
Click to expand...
Click to collapse
It doesn't seem it can be anything else but a hardware issue in that case.
NB. Overclocking to a high frequency can cause instability and bring about that issue (but since you experienced it on the stock rom, its quite likely not to be that).

the overclocking helps to speed it up a tad bit.. for the most part it just lags.. i did a clean install just now

Thought I would jump in. Stock ics would slow down and lag on me, jittery transitions poor performance in games or movies, but it took an hour not a few minutes. However testing the T20 kernel before the release kernel had that exact issue, bogging and lagging within minutes.
His release kernel doesnt do it, and flex extreme as well as my cm9 builds don't, even with T20 kernel. Consider flashing that kernel to see what happens.
Side note...what issues did you have with cm9? And what release? My build 1 has been running for 3 days no reboots stable as can be undervolted and OC when needed. Something to maybe think to try to see if it persists. T20 kernel works fine with it too.
Tapatalked from my Galaxy S II.

Crimson Ghoul said:
Does any one else's a100 become super laggy after a few minutes of being on.. I am running the latest flex reaper I even overclock it all the way but I get this huge lag after the first few minutes of being on.. anyone else experience this or have a fix for this?
Click to expand...
Click to collapse
Yup, EVERYTIME I turned on my screen then unlocked it to laggggggg for a lil while. I'm now using CM9 n that issues gone. Try CM9
forum.xda-developers.com/showthread.php?t=1705554
A100 Running CM9 Nightly ROM n ezT20 OC Kernel :-D

To prevent the lagg after unlock, I set the governor to ondemand and the minimum frequency to 312.

eww245 said:
To prevent the lagg after unlock, I set the governor to ondemand and the minimum frequency to 312.
Click to expand...
Click to collapse
That reminds me...setting a screen off profile with the same min/Max speed can cause issues with that, give Max a notch or two higher. And don't have it change the governor leave it the same. So like interactive screen on Myst nit be conservative screen off, doesn't work that way.
Tapatalked from my Galaxy S II.

I had the same issue on stock. I noticed there are 2 weather applications installed (version 1 and version 2) immediately after I disabled the old weather application (version 1) this stopped happening. I used the ICS GUI to do the disable.
This might not be the case in custom rom, but is true for stock. Post reply and let me know if this fixed it for you also.

Crimson Ghoul said:
Does any one else's a100 become super laggy after a few minutes of being on.. I am running the latest flex reaper I even overclock it all the way but I get this huge lag after the first few minutes of being on.. anyone else experience this or have a fix for this?
Click to expand...
Click to collapse
Do you have a micro SD card plugged in? Try reformatting the card with a computer. Worked for me.
Sent from my A100 using XDA

I felt the need to add my two cents in this....this has been happening to me for the longest with the flex reaper rom ONLY. I've used stock and ZN's rom and those did not lag after unlock...only flex reaper. I'm currently using flex reaper and still experience it from time to time but doesn't destroy my day at all...

Give the CM9 nightly ROM's a go. No Bluetooth n no HDMI audio, but everything else is fine n damn smooth. Those issues will be fixed though
A100 Running CM9 Nightly ROM n ezT20 OC Kernel :-D

eww245 said:
To prevent the lagg after unlock, I set the governor to ondemand and the minimum frequency to 312.
Click to expand...
Click to collapse
I installed Flex 100 Reaper with stock and it it seemed to run smooth enough. Then I installed the OC kernal, and started to get lag. I was looking around to find the OC settings, but can't see it anywhere in settings..
Can anyone direct me to where can I adjust the governor/max/min CPU settings?
Sorry for the noob question.

htc_softbank said:
I installed Flex 100 Reaper with the OC kernal, and started to get lag. I was looking around to find the OC settings, but can't see it anywhere in settings..
Can anyone direct me to where can I adjust the governor/max/min CPU settings?
Sorry for the noob question.
Click to expand...
Click to collapse
Setcpu from the play store.
The overclock settings are not integrated like CM.

[Q] CPU throttleed--why? and..best CPU utilization monitor?

I'm running Albinoman's JB RC3 ROM, and like it a lot. The only significant problem I have is occasional severe sluggishness. When it happens, I'll open IntelliControl and I notice either of two things going on:
1) I'll see that the max CPU speed has been reset to 664000 or something close to that (it's always the same number, but I don't remember exactly what it is...600-something). Once I crank the max limit back up to 1036800, things are good again. What keeps resetting the CPU limit to such a low level, and how do I stop it from doing that???
2) I'll see that the CPU is maxed out at 1036800, but I can't figure out what's chewing up the CPU. What tool can I use to see what process is consuming all the CPU cycles when that happens?
Thanks for the help...

1. I can't tell you why it happens... but I know it is a common problem on the JB ROMs (on the Dinc). There was quite a lot of discussion about it. I know the devs are aware of the issue and were working on it.
2. I don't know of anything that will graph percentage of cpu cycles, or anything exactly like that. But try hooking the phone up to the PC and run ddms (part of the adb tool set) and see what it is doing (or failing to do). While ddms is running in verbose mode it will give you a running output of everything the phone is doing (along with all the errors and warnings).

MysticCobra said:
I'm running Albinoman's JB RC3 ROM, and like it a lot. The only significant problem I have is occasional severe sluggishness. When it happens, I'll open IntelliControl and I notice either of two things going on:
1) I'll see that the max CPU speed has been reset to 664000 or something close to that (it's always the same number, but I don't remember exactly what it is...600-something). Once I crank the max limit back up to 1036800, things are good again. What keeps resetting the CPU limit to such a low level, and how do I stop it from doing that???
Click to expand...
Click to collapse
That's because he's using an older version of Evervolv's qsd8k-common. It was fixed on Oct 10 with Change I3a0fff83: powerHAL: fix the screen off bug. This is one of the reasons I do nightlys, is to get all the new tweaks. This bug won't be fixed in his ROM till he resyncs his source and recompiles. It's triggered by the screen turning off. There's a workaround with Tasker, but since this bug is no longer in my ROM, I quit looking at it.
MysticCobra said:
2) I'll see that the CPU is maxed out at 1036800, but I can't figure out what's chewing up the CPU. What tool can I use to see what process is consuming all the CPU cycles when that happens?
Click to expand...
Click to collapse
CPUSpy is a pretty good app.

MysticCobra said:
I'm running Albinoman's JB RC3 ROM, and like it a lot. The only significant problem I have is occasional severe sluggishness. When it happens, I'll open IntelliControl and I notice either of two things going on:
1) I'll see that the max CPU speed has been reset to 664000 or something close to that (it's always the same number, but I don't remember exactly what it is...600-something). Once I crank the max limit back up to 1036800, things are good again. What keeps resetting the CPU limit to such a low level, and how do I stop it from doing that???
2) I'll see that the CPU is maxed out at 1036800, but I can't figure out what's chewing up the CPU. What tool can I use to see what process is consuming all the CPU cycles when that happens?
Thanks for the help...
Click to expand...
Click to collapse
For #1, a possible fix could be to use this power.qsd8k.so provided by tiny4579:
http://forum.xda-developers.com/showpost.php?p=32552961&postcount=264
Replacing this file fixed the issue on Pons's ROM, but it may wreak havoc on Albinoman's, I have no way to know. Make sure you have a good nandroid backup before attempting to use it. Or, just wait for Albinoman to release a newer ROM with the problem fixed in the source.

musical_chairs said:
For #1, a possible fix could be to use this power.qsd8k.so provided by tiny4579:
http://forum.xda-developers.com/showpost.php?p=32552961&postcount=264
Replacing this file fixed the issue on Pons's ROM, but it may wreak havoc on Albinoman's, I have no way to know. Make sure you have a good nandroid backup before attempting to use it. Or, just wait for Albinoman to release a newer ROM with the problem fixed in the source.
Click to expand...
Click to collapse
It should work fine on Albinoman's ROM. powerHAL is a generic jellybean feature and should work on all JB ROM's. You won't need the fix however on either of Pon's ROMs whether AOKP or CM10.

I'm finding the same issue on the 11/08 build. I replaced the file with the one you uploaded, yet no change. Still reverts to 614 when the screen is off.
I'm managing it with both Incredicontrol and Juicedefender, so on wake it returns to 1075, and the SAv2 seems much smoother than interactive for me. If there's a fix in the newer builds I may flash one (if I get the time), but for now I'm really impressed by how well this one is running.
Thanks,
...sorry...I was on the phone...

omniatic said:
I'm finding the same issue on the 11/08 build. I replaced the file with the one you uploaded, yet no change. Still reverts to 614 when the screen is off.
I'm managing it with both Incredicontrol and Juicedefender, so on wake it returns to 1075, and the SAv2 seems much smoother than interactive for me. If there's a fix in the newer builds I may flash one (if I get the time), but for now I'm really impressed by how well this one is running.
Thanks,
...sorry...I was on the phone...
Click to expand...
Click to collapse
It's supposed to change to 614 on screen off. The bug was that it would stick at 614 even on screen on.
I don't recommend that lib for cm. It's outdated.
Also I don't use sav2 anymore as it doesn't and won't implement project butter. Also interactive can be more aggressive than sav2 as it can jump frequency on touch via boostpulse which sav2 doesn't have.
Sent from my Galaxy Nexus using Tapatalk 2

Oh, well, then I guess I'll give the interactive another try. Maybe just needs to settle in longer. Got so used to ICS, wasn't sure what to expect from JB. Guess it's time I read back a few pages and see what else I've missed.
...sorry...I was on the phone...

Thanks, guys--appreciate the help!

Maybe its out of topic but since i still cant post on dev sub forum i wanna ask a question here to pons.
Im running your CM10 20121114, whenever i play music with appolo it always reboot my dinc.
Is any other had this problem too?

alph0 said:
Maybe its out of topic but since i still cant post on dev sub forum i wanna ask a question here to pons.
Im running your CM10 20121114, whenever i play music with appolo it always reboot my dinc.
Is any other had this problem too?
Click to expand...
Click to collapse
Yep, just a tad bit off topic.
I haven't had this problem before. Granted, I've never played music off my Inc, but I haven't heard anyone else complain, either. Can you PM a logcat? And it's always preferable to report errors off latest versions (currently 1120).

PonsAsinorem said:
Yep, just a tad bit off topic.
I haven't had this problem before. Granted, I've never played music off my Inc, but I haven't heard anyone else complain, either. Can you PM a logcat? And it's always preferable to report errors off latest versions (currently 1120).
Click to expand...
Click to collapse
Thanks for the reply Pons. Yes i think i will download the latest build sooner and test it again. Hope it (randon reboot with apollo) will not happen again on my dinc. But if it still, i will pm you the logcat.

alph0 said:
Thanks for the reply Pons. Yes i think i will download the latest build sooner and test it again. Hope it (randon reboot with apollo) will not happen again on my dinc. But if it still, i will pm you the logcat.
Click to expand...
Click to collapse
I use Apollo Music regularly on Pons's CM10, it works fine, doesn't reboot.

alph0 said:
Maybe its out of topic but since i still cant post on dev sub forum i wanna ask a question here to pons.
Im running your CM10 20121114, whenever i play music with appolo it always reboot my dinc.
Is any other had this problem too?
Click to expand...
Click to collapse
Try flashing to his newest build. It fixed a few problems for me and is incredibly fast. I had to reflash gapps from goo.im though because play store was force closing. Also, doubletwist is a better music player imo because it has a better interface and has good integration with the lockscreen.

Anyone else feels battery drains a lot faster on 4.1.2

Korean ver.
Sent from my LG-F180K using xda app-developers app

nope, same with latest 4.0.4

Much better now that it's rooted and setCPU profiles are enabled once again F180L owner.

I actually see a really nice improvement in battery life over 4.0.4. My wakelocks are now 1/4 of what they were. My problem is CPU related - cant get up (to 1.5 ghz... Throttled down to 1.1 almost all the time)

Emm, why do you need 1.5ghz?

Tim4 said:
Emm, why do you need 1.5ghz?
Click to expand...
Click to collapse
I am so confused by this question
Because, like many other people, I bought this phone in part for its processing power. I could have saved a lot of money by getting a slower but uncrippled phone (even stock gingerbread on my Galaxy S was 'good enough' for basic tasks). And yes, I have noticed lags since the speed has been mostly capped at 1.1ghz. I dont expect there to be full speed all the time, but I'd like it to be as snappy as possible when I am doing light activities with it, like web browsing. Why would anybody be content to have a 30% reduction in their phone's capabilities?
UPDATE: the lags I was experiencing seem to have been softare related. They appear to have disappeared after a clean install of JB and manual install of all apps from play store
---------- Post added at 12:24 PM ---------- Previous post was at 12:09 PM ----------
Hentitan said:
Korean ver.
Sent from my LG-F180K using xda app-developers app
Click to expand...
Click to collapse
Oh yeah. What is draining your battery? Is it a specific application or just the OS? If its the OS you can install Better Battery Stats and take a look at your kernel wakelock statistics.

Something wrong with your unit, cause mine one doesnt lag at all even on 700mhz with 2 cores disabled.
Also on 1.1ghz its still most powerfull CPU on the market, but its your way.
I believe you can disable thermal protection in service menu.

Tim4 said:
Something wrong with your unit, cause mine one doesnt lag at all even on 700mhz with 2 cores disabled.
Also on 1.1ghz its still most powerfull CPU on the market, but its your way.
I believe you can disable thermal protection in service menu.
Click to expand...
Click to collapse
Thanks for your advice to check the service menu in more depth but I didnt see the option there. I wouldnt really want to disable it if I could since it does have a use (I'd rather my battery didnt overheat and explode or something ).
Unlikely that there is something wrong with my unit. The lags arent choppy, per se, but more fractional delays that werent there before the upgrade to JB. I probably would not have said anything if I hadn't seen the phone's prior behaviour. And yes, it is my way - I like things to function as they were intended regardless of whether the current performance is "good enough". Lopping off the top multiplier almost entirely seems like a crude way to regulate the operation and temperature of the phone [.. but the new information below suggests that this isnt intentional...] . If I have to compromise at some level, I will gladly take this (nearly imperceptible) loss of function for the improved battery life I am seeing in this ROM.
Update: the weird frequencies I have been seeing have been reported by others using the same rom as me. It seems to be related to the kernel.

Here we go. Just installed setcpu to show you the service settings works. Also im able to set 100% brightness whenever i want.
I used to underclock cpu on ics, but someday ive realized LTE eats battery 10x times faster, so everything ive done with setcpu is kinda useless.
So i just dont care whats going on with cpu freq since it still lighting fast.
Also JB doesnt lag even on old 1ghz devices cause of triple buffer and forced vsync. I think you still should check your phone.
p.s. Latest F180K official rom

Tim4 said:
Here we go. Just installed setcpu to show you the service settings works. Also im able to set 100% brightness whenever i want.
I used to underclock cpu on ics, but someday ive realized LTE eats battery 10x times faster, so everything ive done with setcpu is kinda useless.
So i just dont care whats going on with cpu freq since it still lighting fast.
Also JB doesnt lag even on old 1ghz devices cause of triple buffer and forced vsync. I think you still should check your phone.
p.s. Latest F180K official rom
Click to expand...
Click to collapse
Thanks again for your advice, although that screenshot has nothing to do with the service settings and JB does lag quite a bit on older 1 Ghz devices, as I can attest by having JB running on my Samsung Galaxy S. I reinstalled JB as cleanly as possible and manually reinstalled all my usual apps from the play store and the lags seem to have disappeared. Maybe there was a problem with my recovery softare ? I edited my earlier post to reflect this, but the change in CPU frequency is still there.
As I was trying to say before, you and I are using different phones and different roms. It seems to be a recognized quirk with the rom I am using that while the phone is unplugged, the cpu frequency and screen brightness are very heavily regulated (cannot run @ 1.5 or full brightness even while phone is cool; goes away when the phone is plugged in). Please do not start telling me that 100% brightness is as unnecessary as 100% cpu frequency (I dont ever use 100%). I think you and I will just disagree on acceptable limitations of capabilities, even if I agree with you that they dont affect normal phone use at all. I see it as a mystery that needs solving.
And I am glad to hear that your phone works so well with the official rom . I could wait for official JB on the e973 but I'm impatient and Houstonn did a great job with the port.

So your phone's service menu doesnt have the High Temperature Property and the Thermal Daemon disable buttons?
You still can ask someone to disassemble korean version service menu to find the flags so you can use it on E973

Tim4 said:
So your phone's service menu doesnt have the High Temperature Property and the Thermal Daemon disable buttons?
You still can ask someone to disassemble korean version service menu to find the flags so you can use it on E973
Click to expand...
Click to collapse
There's a chance I'm still just missing it or looking for the wrong thing... Could I ask you to just take a screen shot of your menu setting for me?

Sure lol

Tim4 said:
Sure lol
Click to expand...
Click to collapse
ha ha, yeah I definitely dont have that option. Thanks a lot.
UPDATE: This fixed all problems

no hidden menu for korean versions?
Sent from my LG-F180K using xda app-developers app

Actually the screenshot is from F180K
3845#*180#