Related
For some odd reason, I lost adb functionality (i.e. any adb command issued receives "error: device not found"). I looked in Device Manager and noticed that MyHTC was gone! I looked at my phone and USB debugging was enabled and in charge only. I could put it in USB Drive mode and the PC would recognize it as a USB Mass Storage Device so that I could exchange and view files but no adb.
I searched and searched on this issue for hours and installed over a half a dozen "androidusb.inf" driver files several times over. Every install generated the Code 10 error where Device Manager was lacking some information from the driver file and could not start the device. I reinstalled HTC Sync and gave that a try...nothing. Downloaded USBDeview and uninstalled all HTC drivers including the HTC Android USB Device and tried again to no avail. WTF?! What else am I supposed to do?
Well, in a "what the hell, let's give it a try" kind of moment, I decided to toggle the USB debugging off and then back on (and yes, it was checked and on the whole time). WORKS!!! WHAT THE CRAP?!! MyHTC is back in Device Manager and everything is back to normal. I'm glad but irritated!
I share this story in hopes that if someone else stumbles on this problem, they will not have to go through the same headache as I did. Just thought this was odd considering how many times I have plugged and unplugged and never had any problems with adb.
Toggle USB Debugging....so simple. *rolleyes*
Same Issue
I've got the same issue on my EVO 4G. Just installed the latest CM7 and now it tell me device not recognized. If I manually install the drivers it gives me the same code 10. I can't bring up the phone as a storage device and toggling the debugging is not working. Any ideas?
SillyJay said:
I've got the same issue on my EVO 4G. Just installed the latest CM7 and now it tell me device not recognized. If I manually install the drivers it gives me the same code 10. I can't bring up the phone as a storage device and toggling the debugging is not working. Any ideas?
Click to expand...
Click to collapse
You installed the hboot drivers correctly?
Boot into recovery, with usb debugging enabled, connect to pc, it should install the drivers.
Still the same
Even when I reboot into recovery it still gives me "USB Device not recognized." I previously had MikFroyo on my phone with no problems. I'm at a loss.
SillyJay said:
Even when I reboot into recovery it still gives me "USB Device not recognized." I previously had MikFroyo on my phone with no problems. I'm at a loss.
Click to expand...
Click to collapse
You most likely have a bad cable, do you have another one you can try?
Possibility
Not at the moment but that may explain it. Still seems weird for it to just go out right as I change to CM7, but still a possibility. I am going to run and grab my other cable. Thanks for the advice.
No Luck
The new USB cable didn't fix the problem. Also, in device manager, even with the driver installed its labeled as "unknown device."
If I boot into hboot the computer recognizes it.
**update: After rebooting from the hboot, my phone is recognized by the computer however, a disk drive is not coming up in "my computer." I have USB storage turned on but Im not getting anything.**
Any help would be much appreciated!
Sad Day
Apparently the Micro USB port on the bottom of my phone is going bad... I talked with some other people who've had the same problem. HTC knows that the ports aren't very sturdy as well. Well... sad day for me.
Also if you're getting the notice from windows saying that you your device will run faster in a 2.0 usb port and you know the port is 2.0 ... chances are your port is going bad as well.
*****UPDATE*****
Flashed to MikFroyo and none of the above stated problems. I would venture that it was CM7 but apparently everyone else is able to use it so who knows.
Dezire z keeps askinf for MTP drivee?? i recently flashed mexdroid rom, and in the beginning none of the usbs would connect my phone. I thought it was a nightly issue as it was based off of a nightly but now its using RC1.
Recently i played around, it wouldnt connect with the "ADB or Android phone driver." I fixed that and those work fine in Device Manager in Windows 7. However!, in device manager it KEEPS asking for MTP. i tried uninstalling, updating, everything!! and it just wont find my htc desire z.
ADB can find it when using command prompt. It can even logcat, and its weird why ADB can see it but windows cant. I have posted a Download link to the Logcat file. Im hoping anyone here can help me.
http://dl.dropbox.com/u/21509455/logcat.txt
thanks
edit* i think i read somewhere Android doesnt use MTP drivers....-confused-
windows 7 can see my phone and lets me safely remove it too, but wont let me see it in my computer.
issues I was having with W7 x64 were resolved by PDANet. you might try it out, although your issue is slightly different than mine... the device was entirely unrecognizable (by adb, fastboot, the whole shebang).
edit: NOTE you don't need to actually use PDAnet, it will just locate an appropriate driver and install it for you, then you can uninstall it from your PC.. unless you want to use it, of course. pretty slick.
pmcqueen said:
issues I was having with W7 x64 were resolved by PDANet. you might try it out, although your issue is slightly different than mine... the device was entirely unrecognizable (by adb, fastboot, the whole shebang).
edit: NOTE you don't need to actually use PDAnet, it will just locate an appropriate driver and install it for you, then you can uninstall it from your PC.. unless you want to use it, of course. pretty slick.
Click to expand...
Click to collapse
ive done this and it found the proper driver. "Android phone" BUT when it tries to connect with device, it says "failed to handshake with device" and proceeds to uninstall pdanet. Is it because its conflicting with windows 7 cant find the MTP driver?.... sooo confused.. never, ever had this problem
edit* after pdanet is uninstalled, the Android phone driver works fine, but MTP does not.
jark99 said:
ive done this and it found the proper driver. "Android phone" BUT when it tries to connect with device, it says "failed to handshake with device" and proceeds to uninstall pdanet. Is it because its conflicting with windows 7 cant find the MTP driver?.... sooo confused.. never, ever had this problem
edit* after pdanet is uninstalled, the Android phone driver works fine, but MTP does not.
Click to expand...
Click to collapse
that's a bugger.
when you plug the phone in, in device manager, does it show as a USB mass storage device under the USB controller section? to check: unplug all usb devices (aside from input devices like keyboard/mouse/what-have-you). plug in your phone and go to device manager (right click my computer->manage->device manager). under USB controllers, check and see if there is a USB mass storage device. assuming you have disconnected any other storage media, this is your phone.
if it does:
uninstall this driver, unplug your phone, restart, plug your phone back in.
if it doesn't:
my next step (take it for what it's worth - I'm sure there's an easier way) would be to unplug all usb devices (including keyboard/mouse - anything USB related), uninstall EVERYTHING under the USB Controller submenu, then restart and plug the phone in.
W7 should automatically recognize and reinstall the USB host controllers and hubs.
edit: are you using any other USB storage devices? thumb drives, ext harddrives, etc? do they work?
pmcqueen said:
that's a bugger.
when you plug the phone in, in device manager, does it show as a USB mass storage device under the USB controller section? to check: unplug all usb devices (aside from input devices like keyboard/mouse/what-have-you). plug in your phone and go to device manager (right click my computer->manage->device manager). under USB controllers, check and see if there is a USB mass storage device. assuming you have disconnected any other storage media, this is your phone.
if it does:
uninstall this driver, unplug your phone, restart, plug your phone back in.
if it doesn't:
my next step (take it for what it's worth - I'm sure there's an easier way) would be to unplug all usb devices (including keyboard/mouse - anything USB related), uninstall EVERYTHING under the USB Controller submenu, then restart and plug the phone in.
W7 should automatically recognize and reinstall the USB host controllers and hubs.
edit: are you using any other USB storage devices? thumb drives, ext harddrives, etc? do they work?
Click to expand...
Click to collapse
Under the usb section in device manager, i have about 8 or so usb controllers and stuff. Im using a Gateway Laptop and only one thing is using a usb port--- the mouse. Thats all. So i dont really have a clue which one is my htc phone because when plugging it in and going into device manager the only devices i remember using the phone were adb, android phone, and Now MTP. If i could pinpoint which usb controller is using my phone ill uninstall it. Other than that, what else is there? This is the strangest problem ever
Sent from my HTC Vision using XDA App
sighh, comeon guys. here ill post some pics of what is going on
Here are the pics of what is going on!!
Normal mode (no phone plugged in) - http://dl.dropbox.com/u/21509455/normal%20mode.jpg
Phone plugged in mode - http://dl.dropbox.com/u/21509455/phone%20plugged%20in.png
Uninstalled MTP & ADB driver Picture (looking for drivers) -http://dl.dropbox.com/u/21509455/phone%20uninstall%20drivers.jpg
Phone with ADB driver but no MTP - http://dl.dropbox.com/u/21509455/phone%20with%20driver%20found%20but%20no%20mtp%20.jpg
hope this helps , if you find something that can make this work let me know ASAP
140 views? and no one knows how to fix this problem?? anyone? hello?
jark99 said:
140 views? and no one knows how to fix this problem?? anyone? hello?
Click to expand...
Click to collapse
Have you tried the drivers from the official HTC Sync software? Also, are you actually trying to use the phone as an MTP device or as a USB mass storage device? I don't think you can use both at the same time (though I don't use this ROM so maybe things have changed). If you don't actually want the MTP functionality, I wouldn't worry about it.
Also, I noticed the notes for the ROM says "USB mounting is not working on a Windows OS computer" is a known issue. Not sure if that could be related...
ianmcquinn said:
Have you tried the drivers from the official HTC Sync software? Also, are you actually trying to use the phone as an MTP device or as a USB mass storage device? I don't think you can use both at the same time (though I don't use this ROM so maybe things have changed). If you don't actually want the MTP functionality, I wouldn't worry about it.
Also, I noticed the notes for the ROM says "USB mounting is not working on a Windows OS computer" is a known issue. Not sure if that could be related...
Click to expand...
Click to collapse
im trying to use it as a mass storage device, MTP isnt supposed to show up from what i read. but now it wont start without MTP
did you try what I pm'd you earlier today?
pmcqueen said:
did you try what I pm'd you earlier today?
Click to expand...
Click to collapse
windows 7 home doesnt have that script gpedit.msc
i looked all over google and it doesnt work . only pro and business versions have it.
Did the HTC Sync software not work? Also, have you tried formatting your SD card? Might be a long shot, but if it was ever used in MTP mode at one point, maybe your comp is detecting the files and thinking it's still an MTP device. Not sure if it works that way though...
Did you ever set the phone to MTP mode in the past? Like if you were ever on a Sense-based ROM. Maybe if you had it in MTP mode prior to flashing the new ROM, it stayed in it. Once again, no clue if it works that way since I've never used MTP on this phone before, but might be worth trying if you are out of options.
STILL havent fixed this MTP driver issue, have tried everything including the post above me!....NOTHING IS WORKING. why is it being recognised as mtp, when all i need is use the sd card.
this has been up for a week, seriously no one knows how to fix it?
jark99 said:
this has been up for a week, seriously no one knows how to fix it?
Click to expand...
Click to collapse
I'm guessing it's because no one else has encountered this problem before...
So what happened when you flashed back to a Sense-based ROM? I've never used one, but I thought when you connect the phone via USB, you have to choose what kind of connection you want (e.g., HTC Sync connection vs Disk Drive). Are you saying even when you choose to connect as a drive, the phone still shows up only as an MTP device (which I'm assuming is what is used when in HTC Sync mode)?
ianmcquinn said:
I'm guessing it's because no one else has encountered this problem before...
So what happened when you flashed back to a Sense-based ROM? I've never used one, but I thought when you connect the phone via USB, you have to choose what kind of connection you want (e.g., HTC Sync connection vs Disk Drive). Are you saying even when you choose to connect as a drive, the phone still shows up only as an MTP device (which I'm assuming is what is used when in HTC Sync mode)?
Click to expand...
Click to collapse
i switched to MIUI rom where i can mount sd card, and it still shows up as MTP in device manager on windows. Its not a rom issue, its a issue with WINDOWS seeing my device as a MTP and not STorage ....stupid windows 7.
jark99 said:
i switched to MIUI rom where i can mount sd card, and it still shows up as MTP in device manager on windows. Its not a rom issue, its a issue with WINDOWS seeing my device as a MTP and not STorage ....stupid windows 7.
Click to expand...
Click to collapse
Well either Windows sees your phone as an MTP device or the phone is actually reporting itself as an MTP device (not sure how it works on phones, but typically Windows communicates with firmware on a USB device to determine its classifications).
I'm guessing you already tried this since it's one of the only threads on the G2 forum when I did a search for MTP...
http://forum.xda-developers.com/showthread.php?t=901449
ianmcquinn said:
Well either Windows sees your phone as an MTP device or the phone is actually reporting itself as an MTP device (not sure how it works on phones, but typically Windows communicates with firmware on a USB device to determine its classifications).
I'm guessing you already tried this since it's one of the only threads on the G2 forum when I did a search for MTP...
http://forum.xda-developers.com/showthread.php?t=901449
Click to expand...
Click to collapse
Thankss i saw some of those. One method i didnt try, but ill try it and let you know how this goes. Thanks for the link
Sent from my HTC Vision using XDA App
Bumppp. Still no proper way to fix this!!
Sent from my HTC Vision using XDA App
anyone find any fix for this MTP ISSUE?
Okay, this is the second time this error has popped up and it's starting to get on my nerves. Anytime I plug my phone into ANY USB port, and this is counting both 2.0 and 3.0 ports, I get the error bubble: Hardware ID Missing. Windows cannot identify the device plugged into the SAMSUNG Mobile USB Composite Device." Honestly, this is beyond irritating.
For one, I am not going to reinstall Windows 7. That's too much hassle for this. Second, ever since someone plugged their Droid into my USB cable so they could charge up their phone, this message started appearing. I tried to reinstall drivers (Samsung driver exe said it couldn't install), uninstall, disable, etc etc, but finally managed to get the damn computer to read it when I stuck it in the 3.0 USB port. Now, just 10 minutes ago, I plug the phone in, I get that error, on a 3.0 USB port.
So, now I have no idea what is going on, nor how to fix it. I've tried searching, but there are no answers. Or, the possible "solutions" don't even work even remotely close.
I could really use some help on this. And, again, please do not mention "Reinstall Windows". That's just too much of a hassle and I'm not going to do that.
You may not want to try this either but try a system restore
Sent from my SPH-L710...if some one helps you press the thanks button
Volknochi said:
Okay, this is the second time this error has popped up and it's starting to get on my nerves. Anytime I plug my phone into ANY USB port, and this is counting both 2.0 and 3.0 ports, I get the error bubble: Hardware ID Missing. Windows cannot identify the device plugged into the SAMSUNG Mobile USB Composite Device." Honestly, this is beyond irritating.
For one, I am not going to reinstall Windows 7. That's too much hassle for this. Second, ever since someone plugged their Droid into my USB cable so they could charge up their phone, this message started appearing. I tried to reinstall drivers (Samsung driver exe said it couldn't install), uninstall, disable, etc etc, but finally managed to get the damn computer to read it when I stuck it in the 3.0 USB port. Now, just 10 minutes ago, I plug the phone in, I get that error, on a 3.0 USB port.
So, now I have no idea what is going on, nor how to fix it. I've tried searching, but there are no answers. Or, the possible "solutions" don't even work even remotely close.
I could really use some help on this. And, again, please do not mention "Reinstall Windows". That's just too much of a hassle and I'm not going to do that.
Click to expand...
Click to collapse
I had the same issue what ended up fixing it for me was watching when I plugged the phone in after a clean driver install and stopping Windows from downloading and installing an updated driver. Dont know if its the same for you but that fixed it for me. I was really frustrated by it and found no help either.
probably an easy fix
definitely don't need to reinstall windows or do a restore. But just to be sure, you don't have kies installed right? Seems to cause problems.if there's no kies installed, go into the device manager and find your phone whatever it's listed as right click and uninstall. Check the little box that says, "delete the driver software for this device". do this for any devices relating to yours. Including the stuff under modems,ports,USB controllers.and tick that box that delete driver software for this device every time you uninstall something. Now, not saying it's necessary but wouldnt hurt, reboot the pc. Then with your phone unplugged, reinstall the Samsung drivers for the phone. Now to make sure windows doesn't DL its own drivers,disconnect from the internet and plug the phone back in. Should be all good.
I won't do a system restore, that won't do anything. Not to mention it would erase some programs that were installed (not related to phone). So, not doing that. Also, my computer will not automatically update any drivers or any thing else, as I have it set to manual mode.
And, I do not have Kies installed. It never worked for me properly, when it came to driver installation. I've done the "go into device manager" bit many times before, it still likes to play the "Hardware ID doesn't match" card. Drivers won't install either. I don't know what it is, but damn this is the most stubborn thing I've ever encountered.
i've post this in other forums today. what i do to get it working is i toggle USB debugging and try it out, then start toggling the ptp and mtp until it works. the combo that works for me is turn on debug, plug in computer, unplug, turn off debug, plug in. if it doesnt work then i toggle back and forth MTP and PTP. 5 tries at most, for me. Also, i did a nandroid back to my oem ICS that was 2 weeks old and just rooted. the problem is worse there. i'm using freegsmr6 with trinity kernel on Tmo. hope it helps.
Ditto
Yeah that whole "Hardware ID missing" was an irritating situation. This is what I recommend as far as making it work.
1. Plug in.
2. When you get the error message, I think its because of a conflict with the ADB interface. Go to Settings, Developer Options, and check off USB Debugging.
3. Plug in once again and it should work. If not, try toggling between Camera and MTP.
I have Windows 7 Ultimate and it works fine for me
I always get that error as well with my SGS 3. I have to reinstall Kies everytime it does that which is annoying.. ANyone has a permanent solution about this?
Fix for me was...
1-plug in phone. Get the hardware ID message. Leave phone plugged in.
2- open device manager. Click on. Android Phone and Uninstall Samsung Android ADB Interface. Also check the "delete software driver" when the dialog box shows.
3-still in device manager. Scroll down to Universal Serial Bus Controllers. Uninstall Samsung Mobile USB Composite Device.
4-unplug phone.
5-reboot pc.
6-install SAMSUNG USB drivers from their site or from here
http://www.epiccm.org/2012/06/cwm-recovery-on-all-sgs3-lte-variants.html?m=1
7-reboot or not. Plug in phone.
This worked for me and no issues for the last 6 days. YMMV..
this works!
stevounit said:
yeah that whole "hardware id missing" was an irritating situation. This is what i recommend as far as making it work.
1. Plug in.
2. When you get the error message, i think its because of a conflict with the adb interface. Go to settings, developer options, and check off usb debugging.
3. Plug in once again and it should work. If not, try toggling between camera and mtp.
I have windows 7 ultimate and it works fine for me :d
Click to expand...
Click to collapse
But why this problem now out of nowhere when everything worked fine before.
Sent from my SPH-L710 using xda app-developers app
Hardware ID missing - SOLVED!!
1. Uninstall any previous instance of Kies/USB driver
2. Download the latest Kies, specific to your S3.
3. Download Samsung USB drivers 1.4.6.0 (I've tried newer versions but they all failed)
4. REBOOT
5. Disconnect from internet (VERY IMPORTANT!!! - forcing Windows to install local drivers ONLY)
6. With the phone disconnected, install Kies + USB drivers downloaded in steps 2,3
7. Connect the phone and let Windows install the drivers.
8. Reestablish the internet connection.
I've done just that, I've connected my S3 to the PC several times, I've also rebooted twice and I've never seen that stupid message again - while of course everything works as expected.
:good::good:4 days later, several times rebooted (phone and PC), several connections with Kies and I have NEVER seen that error again - it works!!
UPDATE!! (Oct.11.2012)
After a few Kies updates and going through various ROM's:
- the procedure listed above works 100% but a few steps are just not needed (redundant) - see bellow
- the problem is mostly caused by Windows "forcefully" trying to install its own drivers, rather than allowing Samsung's suggested.
- Samsung's fault is providing "updated" drivers that don't always work (hence, use the suggested 1.4.6.0 drivers)
- Following EVERY Kies update, DISCONNECT from internet before plugging your phone (otherwise you'll have to go through this, AGAIN).
Some suggested here that plugging the phone into a different USB port (without disconnecting from internet) would be the culprit - which happens to be true, but as a mere effect, not the cause: every time an unknown device is plugged into a different USB port, Windows is trying to download/install the appropriate drivers if it doesn't recognize the hardware - and there you are again.
So, the simplified procedure becomes:
1. Not needed - leave Kies installed, as is - no harm at all
2. N/A
3. YES
4. Not (always) required
5. MUST
6. MUST
7. MUST
8. Yes
Furthermore, if still interested in connecting your I747(M) as UMS (USB mass storage) the solution presented here works. I tested it myself - read my comment on this post for the very few existing hiccups.
- while installing the USB mass storage device drivers you don't have to disconnect from the internet
Install Drivers
Have you tried just installing the drivers directly from Samsung? That is all I did when I had problems and it worked.
tyler1037 said:
Have you tried just installing the drivers directly from Samsung? That is all I did when I had problems and it worked.
Click to expand...
Click to collapse
For someone experiencing the "hardware ID missing" error, just reinstalling the drivers won't do anything. Like many others, I've been banging my head trying to solve this for quite some time; the suggested steps are truly a compilation of successful ideas and trials mingled with tons of frustration, coming from my own experience as well as from many different people and forums.
If, on the other hand, you had a different type of connectivity issues - without this error, then, yes, reinstalling the drivers is Samsung's recommendation.
billard412 said:
definitely don't need to reinstall windows or do a restore. But just to be sure, you don't have kies installed right? Seems to cause problems.if there's no kies installed, go into the device manager and find your phone whatever it's listed as right click and uninstall. Check the little box that says, "delete the driver software for this device". do this for any devices relating to yours. Including the stuff under modems,ports,USB controllers.and tick that box that delete driver software for this device every time you uninstall something. Now, not saying it's necessary but wouldnt hurt, reboot the pc. Then with your phone unplugged, reinstall the Samsung drivers for the phone. Now to make sure windows doesn't DL its own drivers,disconnect from the internet and plug the phone back in. Should be all good.
Click to expand...
Click to collapse
Just wanted to say thank you. Did this and the last 2 days, works everytime. I made sure that after the first time I plugged the phone in after doing all this, and the screen pops up asking what I wanted to do, made sure to check the box for "do this everytime" and then choose the view folder option or whatever that is.
Thank you again,
Whiteice
One thing I have tried which might help others - I had the Android Developers toolkit installed on my machine, which I've removed and I also removed the HTC Sync software which was for my old desire.
Rebooted, installed the SG Toolkit (can't remember which post I found it in) and then chose option one after selecting firmware to install drivers.
I cancelled the "Windows Updates" bit of the driver detection and it found the first item, and had "item disconnected" for the remaining three.
Unplugged and plugged back in and voila it works.
This worked for approx 5 mins and then stopped, however I did all the above with debugging on, debugging is now off and all seems well (touch wood). However looking at putting on a different kernal to expose storage as mass storage and also get around cifs issues.
Hope this helps someone.
nacos said:
1. Uninstall any previous instance of Kies/USB driver
2. Download the latest Kies, specific to your S3.
3. Download Samsung USB drivers 1.4.6.0 (I've tried newer versions but they all failed)
4. REBOOT
5. Disconnect from internet (VERY IMPORTANT!!! - forcing Windows to install local drivers ONLY)
6. With the phone disconnected, install Kies + USB drivers downloaded in steps 2,3
7. Connect the phone and let Windows install the drivers.
8. Reestablish the internet connection.
I've done just that, I've connected my S3 to the PC several times, I've also rebooted twice and I've never seen that stupid message again - while of course everything works as expected.
:good::good:4 days later, several times rebooted (phone and PC), several connections with Kies and I have NEVER seen that error again - it works!!
Click to expand...
Click to collapse
Thank you so much for this. This solution worked for me.
nacos said:
1. Uninstall any previous instance of Kies/USB driver
2. Download the latest Kies, specific to your S3.
3. Download Samsung USB drivers 1.4.6.0 (I've tried newer versions but they all failed)
4. REBOOT
5. Disconnect from internet (VERY IMPORTANT!!! - forcing Windows to install local drivers ONLY)
6. With the phone disconnected, install Kies + USB drivers downloaded in steps 2,3
7. Connect the phone and let Windows install the drivers.
8. Reestablish the internet connection.
I've done just that, I've connected my S3 to the PC several times, I've also rebooted twice and I've never seen that stupid message again - while of course everything works as expected.
:good::good:4 days later, several times rebooted (phone and PC), several connections with Kies and I have NEVER seen that error again - it works!!
Click to expand...
Click to collapse
Thanks for this i will try it tomorrow as still new to these tabs.
For moment i change to camera PTP and it pops up, so at least i can use it for now.
Will let you know how i get on.
Best wishes :good:
adamspud said:
One thing I have tried which might help others - I had the Android Developers toolkit installed on my machine, which I've removed and I also removed the HTC Sync software which was for my old desire.
Rebooted, installed the SG Toolkit (can't remember which post I found it in) and then chose option one after selecting firmware to install drivers.
I cancelled the "Windows Updates" bit of the driver detection and it found the first item, and had "item disconnected" for the remaining three.
Unplugged and plugged back in and voila it works.
This worked for approx 5 mins and then stopped, however I did all the above with debugging on, debugging is now off and all seems well (touch wood). However looking at putting on a different kernal to expose storage as mass storage and also get around cifs issues.
Hope this helps someone.
Click to expand...
Click to collapse
The Android Developers toolkit DOES install the USB drivers 1.4.6.0 - which seems to be the ONLY one that works, BUT the rest of the steps suggested in my previous post are needed in order to get rid of the problem - otherwise the fix is just temporary.
Re-loading OS drivers corrected issue.
tyler1037 said:
Have you tried just installing the drivers directly from Samsung? That is all I did when I had problems and it worked.
Click to expand...
Click to collapse
I removed the updates to Kies on my Note and uninstalled the Kies update on the PC which is what started this issue of the OS not recognizing the device and then a fresh driver load for my phone from the Samsung site. Worked Perfectly, Thanks!
Cowoholy
Hi all...I am new to XDA forum, but have been browsing in the trove of information to help with my problem. At the end I am resorting to posting a new thread to hopefully help me in resolving this problem or provide a good explanation why it does not work.
Problem: I am trying to use the USB cable to transfer files to my SD Card. (I am not sure what reason, but someone has informed me that either Samsung's proprietary software Kies does NOT work, you can only transfer using Samsung KIES Air...which is painfully slow.)
Now here is my situation:
1. I have a Bell Canada - Samsung Galaxy Note-2
2. The Phone has been unlocked and rooted (using Odin)
GOAL:
- I don't care if I need to transfer files to the SD card, and then sort the files out afterwards on the phone.
- Primary goal is to allow me to transfer files (music, mp3, etc.) via USB cable.
Your help is greatly appreciated...in providing some sort of clear cut instructions or directions.
Thank you in advance.
Android Noob User - Daniel :crying:
I know you didn't ask for this, but could you possibly use Airdroid? It has always been reliable for me and honestly it's my best solution for myself because we don't actually have UMS anymore, sigh.
Airdroid Vs. Kies Air
Thanks for the response and recommendation.
So is Airdroid? better or the same as Kies Air?
dckp said:
Thanks for the response and recommendation.
So is Airdroid? better or the same as Kies Air?
Click to expand...
Click to collapse
I've never used Kies so I can't say!
But basically, you download the app from google play and go to web.airdroid.com and you type in the code that you see in the app. From there you can read your phone's text messages and transfer files and do other things via your wifi connection. File transfer on my (good) wifi network is fairly fast (about the same as using a usb cord) and it's good for me because I personally use Ubuntu and Chrome OS, so the USB storage options don't work or don't work well.
usb driver
All you need is go to samsung website and install the usb driver. You should have an option to do this during the kies installation too.
dckp said:
Hi all...I am new to XDA forum, but have been browsing in the trove of information to help with my problem. At the end I am resorting to posting a new thread to hopefully help me in resolving this problem or provide a good explanation why it does not work.
Problem: I am trying to use the USB cable to transfer files to my SD Card. (I am not sure what reason, but someone has informed me that either Samsung's proprietary software Kies does NOT work, you can only transfer using Samsung KIES Air...which is painfully slow.)
Now here is my situation:
1. I have a Bell Canada - Samsung Galaxy Note-2
2. The Phone has been unlocked and rooted (using Odin)
GOAL:
- I don't care if I need to transfer files to the SD card, and then sort the files out afterwards on the phone.
- Primary goal is to allow me to transfer files (music, mp3, etc.) via USB cable.
Your help is greatly appreciated...in providing some sort of clear cut instructions or directions.
Thank you in advance.
Android Noob User - Daniel :crying:
Click to expand...
Click to collapse
Just in case, make sure that MTP is checked in USB computer connection.
*Settings>Storage> Menu button>USB computer connection> check Media device (MTP)*
I know it may seem obvious to some but it does get overlooked sometimes.
Cheers!
ace862 said:
Just in case, make sure that MTP is checked in USB computer connection.
*Settings>Storage> Menu button>USB computer connection> check Media device (MTP)*
I know it may seem obvious to some but it does get overlooked sometimes.
Cheers!
Click to expand...
Click to collapse
In regards to the downloading the 'Samsung Driver' I have already attempted that, and with no luck of cooperating. Under 'device Manager' in Window 7. The listed device when I plug-in the phone is "Qualcomm CDMA Technologies MSM" with an exclamation mark. I have been trying to try the driver files so I can 'direct' the appropriate drivers file. But no luck locating it. The Samsung Kies installation mention that it has installed, but no luck.
MTP Option:
In regards to the MTP, I do not have that option available on my phone, the only thing avaliable is through the 'Developer option -> Checking/Unchecking USB debugging'
Please Help! :crying:
I have download the driver form the Samsung.com website.
Now, It doesn't technically allow to choose my specific phone model, with my carrier (BELL), so I went with the closest ATT.
I have located the folder with the USB driver, and force window to look through it.
But still windows says it cannot find the correct driver for my device....this is getting frustrating.
HELP...help...help...
dckp said:
MTP Option:
In regards to the MTP, I do not have that option available on my phone, the only thing avaliable is through the 'Developer option -> Checking/Unchecking USB debugging'
Please Help! :crying:
Click to expand...
Click to collapse
That is odd. Do you have a Storage category under System Settings? It should show you available space on internal and sd storage. What happens when you hit the menu button? (button to the left of the home button)
When you connect your USB cable, do you get a notification that says "Connected as a media device"?
Heres what you do.
Make sure you have current samsung usb drivers. Redownload just for fks sake.
Yeah idk wtf ms prob is but its got issues with samsung phones.
So ok drivers gtg?
Plug in phone
Wait for annoying pop up.
Leave phone pluged in and on restart computer.
You should get the all clear but first it may give you the cant recognize drivers thing give it a min should work.
Other solution
Download this
http://www.google.com/url?q=http://...gQFjAA&usg=AFQjCNEJj15zF95WRtG86GXUDNcyErSAGA
Basically just keep going back and forth witj mtp and mount you should kick it in.
And you may need to restart computer.
Sgs3 easy wotks pretty good for me.
You gotta make sure you have the microsoft mtp update installed.
Pia I know.
ace862 said:
That is odd. Do you have a Storage category under System Settings? It should show you available space on internal and sd storage. What happens when you hit the menu button? (button to the left of the home button)
When you connect your USB cable, do you get a notification that says "Connected as a media device"?
Click to expand...
Click to collapse
In regards to your question. Yes It is odd....'Yes" I do have a storage category under System settings. I do see available space on internal and sd storage. BUT Nothing happens when I hit the menu button. Absolutely nothing
dckp said:
In regards to your question. Yes It is odd....'Yes" I do have a storage category under System settings. I do see available space on internal and sd storage. BUT Nothing happens when I hit the menu button. Absolutely nothing
Click to expand...
Click to collapse
I'm sorry. That is my bad. It looks like those options are not available on the stock rom. I thought they were. The option is there on CM.
It looks like it is probably a driver issue. If your computer is not recognizing your device when it is plugged in, it could also be a bad USB cable. If you can try a different cable, see if something different happens when you plug in your phone.
Worst comes to worst, you may just have get a card reader and connect your sd card to your computer that way.
1. Is cable good? It may be sending incomplete signal. The fault could be your device's usb port or cable or pc usb port.
1a. test device with another known working usb cable
1b. test cable with another known working device
2. Is PC port good?
2a. Plug a different, known working USB device into port, do other devices work?
2b. Plug device into another usb port on PC, not into usb hub or front usb ports.
2c. Does it successfully connect for transfer with another PC?
3. Is driver good?
(This is most likely your problem, but a bad usb device, cable, or port can make it more difficult to troubleshoot. )
3a. Re-download driver. BUT BEFORE YOU DO...
use a different browser to download or delete your browser's cache. (Attempting to redownload may just be grabbing the already known poor copy.)
3b. Run Windows Update after driver is installed.
If still having problems.
Search for, download, and run the portable program usbdeview. Attached USB devices will be highlighted. See if it shows up to the system and what it is being recognized as.
It sounds like either a bad driver install or conflicting program/setting.
Turn off antivirus temporarily to rule that out.
For assistance with installing Qualcomm USB drivers, see this post:
http://forum.xda-developers.com/showthread.php?t=1669498
USB will not function with my OnePlus 3, I've loaded drivers and still no avail.
templarsniper said:
USB will not function with my OnePlus 3, I've loaded drivers and still no avail.
Click to expand...
Click to collapse
As regards the attaching of files, you have to have a minimum number of posts to be able to do that.
As regards the USB, be a little more specific like what you are trying to do, which ROM you are running, whether you are rooted, what happens when you connect the phone to PC etc which will enable the members to help you.
There could be several reasons for this, but lets start with the basics.
Have you tried a different cable?
Have you selected File Transfer (MTP) from usb options?
kenboyles72 said:
There could be several reasons for this, but lets start with the basics.
Have you tried a different cable?
Have you selected File Transfer (MTP) from usb options?
Click to expand...
Click to collapse
I get a windows sound like its connecting then in the bottom right where the time is next to that is a root sign then I get a pop up saying exactly.....The last USB device you connected to this computer malfunctioned and Windows does not recognize it. Recommendation.. Try reconnecting the device. If Windows still does not recognize it, your device may not be working properly. When I go to the Device Manager/Control Panel it doesnt do anything. I've tried to add adb to the path but maybe added it to wrong path now it won't come on. If there is a work around maybe to re-add to right path. Device Manager was fine before I added adb and added path as per internet search. Device Manager before would say something like error 39. I've tried MTP that doesn't get it to open up either.
TNSMANI said:
As regards the attaching of files, you have to have a minimum number of posts to be able to do that.
As regards the USB, be a little more specific like what you are trying to do, which ROM you are running, whether you are rooted, what happens when you connect the phone to PC etc which will enable the members to help you.
Click to expand...
Click to collapse
I cant even root for the life of me now, Im on 8.0, I'm trying to just root the phone and to start the computer has to recognize it I understand but it won't, with my Oneplus 2 was fine,(I'm thinking maybe phone doesnt have the drivers built in to the file system, you know when you plug in and turn on MTP it shows the drivers app for Windows?) the only thing it errors plugging in.
I get a windows sound like its connecting then in the bottom right where the time is next to that is a root sign then I get a pop up saying exactly.....The last USB device you connected to this computer malfunctioned and Windows does not recognize it. Recommendation.. Try reconnecting the device. If Windows still does not recognize it, your device may not be working properly. When I go to the Device Manager/Control Panel it doesnt do anything. I've tried to add adb to the path but maybe added it to wrong path now it won't come on. If there is a work around maybe to re-add to right path. Device Manager was fine before I added adb and added path as per internet search. Device Manager before would say something like error 39. I've tried MTP that doesn't get it to open up either.
On my son's pc running windows 10, I didn't have any issues connecting my OP3 to it and viewing files, nor did I have to install any drivers, same for Windows 7.
Hook phone to pc via usb cable.
Pull down notification bar and select "File Transfer" from usb options or go to Settings and search USB and select USB Preferences > File Transfer.
Browse phone from Window's file manager.
If still having issues, you can try and install Oneplus USB drivers, reboot pc and see if the phone can be recognized.
Oneplus USB drivers:
https://app.box.com/s/u47rur40qm5efly6pz41rbhagu5qvc80
Fixed USB problem
kenboyles72 said:
On my son's pc running windows 10, I didn't have any issues connecting my OP3 to it and viewing files, nor did I have to install any drivers, same for Windows 7.
Hook phone to pc via usb cable.
Pull down notification bar and select "File Transfer" from usb options or go to Settings and search USB and select USB Preferences > File Transfer.
Browse phone from Window's file manager.
If still having issues, you can try and install Oneplus USB drivers, reboot pc and see if the phone can be recognized.
Oneplus USB drivers:
https://app.box.com/s/u47rur40qm5efly6pz41rbhagu5qvc80
Click to expand...
Click to collapse
For some reason it's working now don't know what the problem was or even if it was something I did. Either way it's fixed.
templarsniper said:
For some reason it's working now don't know what the problem was or even if it was something I did. Either way it's fixed.
Click to expand...
Click to collapse
If you are running Win 10, you will have to disable driver signing before the correct drivers are installed. May be that was your issue.