problems with s-on usb brick - Desire HD Q&A, Help & Troubleshooting

kernel 2.6.35.10
sense 3.0
android 2.3.5
s-0n
just got a dhd from the bay of fleas,the dhd will not perform any usb functions apart from charging.
i have all the drivers and sdk installed on my pc from my desire bravo.
i searched and found a thread about unrooted usb brick,followed all the instructions in fastboot oem enable blah blah,all i get is waiting for device.
when i attatch the dhd to the usb i get nothing,plug in the bravo and all is ok,also when i select recovery i get the red triangle.
i am at a bit of a loss with this problem,dont want to be stuck on a non rooted sense 3.0 its bloody slower that my aio bravo, i might add the phone functions normally apart from the above problem.
waiting to flash thanks mark

markb63 said:
kernel 2.6.35.10
sense 3.0
android 2.3.5
s-0n
just got a dhd from the bay of fleas,the dhd will not perform any usb functions apart from charging.
i have all the drivers and sdk installed on my pc from my desire bravo.
i searched and found a thread about unrooted usb brick,followed all the instructions in fastboot oem enable blah blah,all i get is waiting for device.
when i attatch the dhd to the usb i get nothing,plug in the bravo and all is ok,also when i select recovery i get the red triangle.
i am at a bit of a loss with this problem,dont want to be stuck on a non rooted sense 3.0 its bloody slower that my aio bravo, i might add the phone functions normally apart from the above problem.
waiting to flash thanks mark
Click to expand...
Click to collapse
When you say it wont perform any USB functions, does it acknowledge that the usb cable has been plugged in? i.e do you get the charge only/ Disc drive menu? have you tried different micro usb cables?

ghostofcain said:
When you say it wont perform any USB functions, does it acknowledge that the usb cable has been plugged in? i.e do you get the charge only/ Disc drive menu? have you tried different micro usb cables?
Click to expand...
Click to collapse
nope,nothing at all.when i plug it in no menu at all,even with the usb connected and boot into bootloader no noise from the pc,totally dead ...

My personal feeling would be that the usb port is possibly damaged.

ghostofcain said:
My personal feeling would be that the usb port is possibly damaged.
Click to expand...
Click to collapse
my thoughts as well,does the dhd use a different cable than the standard desire bravo ?.as i did not get a cable with the phone.
is there anyway of checking if the port is damaged ? thanks

If it charges through PC the usb is fine. It could be that the drivers do not mach. Have you tried updating them or connecting to another PC?
Recovery won't work since the phone is s-on meaning you can't possibly flash a radio on it.
Solution: root.
Sent from my Desire HD using XDA App

Try another cable, some are just charge only.

Related

phone not seen by laptop via usb

Could someone help me on this issue. When i connect my phone via usb to my laptop and on other different laptops/computers i've tried so far, it only charges the phone without mounting sd card or allowing data transfer. I'm using an O2 branded stock htc desire running on froyo. i want to root my phone and install install a custom rom. i don't know how or if possible to make a goldcard without using a usb connection cable to a laptop/pc and for the other processes of rooting and installing a custom rom.
I took it for repairs and a new port was put in and still same problem persists.
You know that you have to manually select mount sd. Also have you tried to connect it via adb, not to transfer files but to see if i usb connection works?
Sent from my HTC Desire using XDA App
For the adb connection, I think this will require USB cable connection or it's there a way to do this without USB cable connection.
Sent from my HTC Desire using XDA App
scorror said:
Could someone help me on this issue. When i connect my phone via usb to my laptop and on other different laptops/computers i've tried so far, it only charges the phone without mounting sd card or allowing data transfer. I'm using an O2 branded stock htc desire running on froyo. i want to root my phone and install install a custom rom. i don't know how or if possible to make a goldcard without using a usb connection cable to a laptop/pc and for the other processes of rooting and installing a custom rom.
I took it for repairs and a new port was put in and still same problem persists.
Click to expand...
Click to collapse
Once you plug in your USB cable, you have to pull the top bar down and manually select to use it as a usb 'disk'...only then will you be able to load it with custom ROM.
As for rooting, I think you need to enable USB debugging for the UnRevoked method....
Evil_Cid said:
Once you plug in your USB cable, you have to pull the top bar down and manually select to use it as a usb 'disk'...only then will you be able to load it with custom ROM.
As for rooting, I think you need to enable USB debugging for the UnRevoked method....
Click to expand...
Click to collapse
when i select it to use as usb disk, the laptop doesn't see it, same for usb debugging.
i tried using a usb hub with four ports to connect my phone to the laptop, the message i get is that '' this usb device is not recognised''. Pls why that message
Any help on this issue. I've been reading on usb brick phones and how to unbrick it. The problem is even when phone is connected via usb in fastboot mode, it still say device is not recognised. i was trying to get the CID number of the phone. i've never rooted or flash a custom rom yet. i started experiencing this when the phone fell on a concrete floor. i don't know if this is hardware related problem or software related.

Problem connecting HTC Desire HD via USB cable

Hi All,
since some days i'm not able to get connection to my PC via USB cable. DHD does'nt even ask for sort of connection - all relative settings on the phone like USB debugg & ask for mod of USB conn are of course checked!
PC doesn't react on my DHD. Anyone did entcounter the same?
I'm workin on ARHD 2.15. Attempts with other ROMS was also not succesfull
Any advice will be highly appreciated!
hann
Have you tried with another computer? If it doesn't work, you've got a usb brick. I remember I had that on my friends desire, but got it fixed using this guide: http://forum.xda-developers.com/showthread.php?t=691639
I don't know if this will work on the desire Hd though...
Thank-you Mate for your response.
Yes I checked it on other pcs and I was at least asked for sort of connection I intended to do. But sdcard wasn't mounted though. Also in fastboot mode loading bootloader usb is not active.
I will try to follow your tip.
Sent from my Desire HD using XDA App
hann2 said:
sdcard wasn't mounted though. Also in fastboot mode loading bootloader usb is not active.
Click to expand...
Click to collapse
got the same problem :/ any ideas??
Just try your card on another phone, or try another card from other phone to pinpoint the problem

USB brick?

I'm hoping someone can help me here, and before people say it, yes I have done a search and tried different options but nothing seems to work.
I'm on 0.93 hboot with s-off and fully rooted for years.
The problem?
I was running Nikez Rom on my Desire and it had a few rebooting issues but nothing to be alarmed of. However after one of these reboots the phone did not charge, computer displays a 'power surge on USB' message and disables usb port. Fastboot is not recognised and fastboot USB does not appear when I connect. Using adb does not identify the device either.
What I have tried to do to resolve
Having read several forum posts around USB bricks and fixing fastboot to changing mtd0.IMG files, nothing has seemed to work. Alternatively, it could be me not following things or not doing things in a logical manner. I have also done a factory reset and flashed sandvold Rom but that hasn't helped either.
Help
I am now almost at the end of my tether (no pun intended), so would really appreciate some help in trying to fix this problem.
What I have not done
I have not yet flashed the stock ruu, but not sure how that would work either if my computer disables the USB port anyway.
Skill level
I'm not an expert so please be gentle.
Thanks
Sent from my HTC Sensation Z710e using xda app-developers app
You are SOFF so the easy way to fix usb brick is to flash 4ext recovery since it has got an inbuilt usb brick repairer. However you are saying fastboot is not working. Even with usb brick fastboot should work. That leads me to believe that the problem may be elsewhere. I would check the computer once.
handy5876 said:
You are SOFF so the easy way to fix usb brick is to flash 4ext recovery since it has got an inbuilt usb brick repairer. However you are saying fastboot is not working. Even with usb brick fastboot should work. That leads me to believe that the problem may be elsewhere. I would check the computer once.
Click to expand...
Click to collapse
Thanks, tried 4ext fix usb brick option also, but did not work. I have a Sensation as well and that works fine re computer, so I don't believe it's a computer issue.
Also, the mains charger (plug) light goes off as soon as I put the Desire on charge but comes back on when I remove the phone from the mains charger - which leads me to believe there is something wrong with the phone usb software, but don't know what that could be.
Are there and other options for me to try? Is my phone usb bricked?
You can try the Unbrick option in 4ext recovery.
Also try on a different USB port or even a different PC.
techwiz98 said:
You can try the Unbrick option in 4ext recovery.
Also try on a different USB port or even a different PC.
Click to expand...
Click to collapse
Thanks - already tried these options.
Just responded above to a similar suggestion.
Any other help appreciated.
ac_utd said:
Thanks, tried 4ext fix usb brick option also, but did not work. I have a Sensation as well and that works fine re computer, so I don't believe it's a computer issue.
Also, the mains charger (plug) light goes off as soon as I put the Desire on charge but comes back on when I remove the phone from the mains charger - which leads me to believe there is something wrong with the phone usb software, but don't know what that could be.
Are there and other options for me to try? Is my phone usb bricked?
Click to expand...
Click to collapse
I dont think the problem is software related. I say this bacause the usb port is not working in either fastboot, recovery or rom. Each of these has got its own usb software and they cant all be bad. It seems to be hardware related. I got a feeling your usb port is fried. Most probably it has a short because your mains charger light is fanning out.
handy5876 said:
I dont think the problem is software related. I say this bacause the usb port is not working in either fastboot, recovery or rom. Each of these has got its own usb software and they cant all be bad. It seems to be hardware related. I got a feeling your usb port is fried. Most probably it has a short because your mains charger light is fanning out.
Click to expand...
Click to collapse
But could this happen while it wasn't connect via mains or computer?
How do I confirm this? Is there a solution if this is, in fact, the problem?
ac_utd said:
But could this happen while it wasn't connect via mains or computer?
How do I confirm this? Is there a solution if this is, in fact, the problem?
Click to expand...
Click to collapse
shut down the phone plug it in and see what the charger does.
or even pull the battery and plug it in. if theres ashort it should still be there
colin_404 said:
shut down the phone plug it in and see what the charger does.
or even pull the battery and plug it in. if theres ashort it should still be there
Click to expand...
Click to collapse
Pulled the battery out of the phone, out it on mains charge, but still main charger light goes off.
Tried another battery & it does the same thing. Tried different mains charger and it does the same thing.
How do I prove it's a hardware or a software issue?
Should I try a stock RUU?
Having read other forums regarding USB bricks, people have been able to access fastboot usb, but I can't.
So, I don't really know what the problem is.
I got fixed by this method.
androidforums [dot] com/desire-support-troubleshooting/485991-pls-help-stuck-cant-mount-sd-card-recovery [dot] html
check above link, replace [dot] 's with " . " (period)
boot to fastboot (back+power) and use the following command in command prompt
fastboot oem enableqxdm 0
This will enable the SDcard function in recovery
fastboot oem eraseconfig
This should fix the usb brick
reflash the rom you want from your recovery (you will need to wipe device via recovery 1st)
Click to expand...
Click to collapse
paddyankee said:
I got fixed by this method.
androidforums [dot] com/desire-support-troubleshooting/485991-pls-help-stuck-cant-mount-sd-card-recovery [dot] html
check above link, replace [dot] 's with " . " (period)
Click to expand...
Click to collapse
Thanks for your message, but the issue is every time I connect the phone to my laptop (and I've tried this on two different laptops), I get a message as below:
"One of the USB devices attached to the computer has malfunctioned, and Windows does not recognise it."
It seems the charge on the USB port of the phone has gone corrupt - if that's at all possible.
Once I get fastboot USB working, I'll be good to go.
I'm on BRAVO PVT1 SHIP S-OFF
HBOOT-6.93.1002
RADIO-5.17.05.23
Surely I can't be the only person to have this issue??
Also, I can access my sd card via ES Explorer.
On most of the usb brick issues, I believe the sd card is inaccessible. However, I can access it.
Therefore, I don;t even know whether my phone has a usb brick or whether it's something else?
Anyone?
Sent from my HTC Sensation Z710e using xda app-developers app
Did you try reinstalling usb drivers on your PC?
Sent from my toaster
yea...my username sucks...deal with it...
abaaaabbbb63 said:
Did you try reinstalling usb drivers on your PC?
Sent from my toaster
yea...my username sucks...deal with it...
Click to expand...
Click to collapse
The computer's not the problem The phone is.
Computer usb ports work fine with other devices and my sensation.

[Q] USB Brick - "USB device not recognized" (no ADB or Fastboot)

Hi guys.
As the title suggest I've run into a USB brick with my Desire HD. I don't know how and can't remember when but it was well after I was flashing custom roms. Basically when I plug it into any PC with any cable it says "USB device not recognized". The phone thinks it's just charging (charges fine otherwise both on PCs and with the normal AC adapter). When I'm in fastboot or hboot it won't say it's in USB mode either.
When I try using Fastboot and ADB on my computer it just says there are no devices connected. I've tried many roms, both with Sense and without going from gingerbread all the way up to ICS and JB with no luck.
I cannot find any solution to this problem anywhere and was just wondering if someone stumbled upon a fix?
My thanks in advance.
Huzi.
[Update]
Plugged it into the USB 3.0 port on my brother's laptop. It turned the phone off. Turned it on and it started installing drivers and it works on there. Haven't tried it out on anything else yet as I'm backing up the files. It turned off the phone and installed it on my computer but didn't work last night. I guess I'll try again once all 11GB are copied over
huzi_a said:
Hi guys.
As the title suggest I've run into a USB brick with my Desire HD. I don't know how and can't remember when but it was well after I was flashing custom roms. Basically when I plug it into any PC with any cable it says "USB device not recognized". The phone thinks it's just charging (charges fine otherwise both on PCs and with the normal AC adapter). When I'm in fastboot or hboot it won't say it's in USB mode either.
When I try using Fastboot and ADB on my computer it just says there are no devices connected. I've tried many roms, both with Sense and without going from gingerbread all the way up to ICS and JB with no luck.
I cannot find any solution to this problem anywhere and was just wondering if someone stumbled upon a fix?
My thanks in advance.
Huzi.
[Update]
Plugged it into the USB 3.0 port on my brother's laptop. It turned the phone off. Turned it on and it started installing drivers and it works on there. Haven't tried it out on anything else yet as I'm backing up the files. It turned off the phone and installed it on my computer but didn't work last night. I guess I'll try again once all 11GB are copied over
Click to expand...
Click to collapse
Same things happening on my one XL. this post is ancient For mine even using RUU doesn't work it goes like device unplugged/cannot be found or something similar. ill try usb 3.0 when i get back to my desktop but this kinda sucks. I just had it repaired days ago.

Unable to Root - USB?

Hi All,
I need help to root and S-OFF my phone. The issue is that my USB charging post does not work (PC and other laptops do not detect it). I have read the Welcome to the HTC Desire (Bravo) Troubleshooting Guide (http://forum.xda-developers.com/showthread.php?t=1275632) and followed Section 11, at step number 7, I am unable to boot into recovery - all i get is a black screen with a red triangle /!\?
My phone is not recognized by the PC when selecting "Disc Drive", "HTC Sync". Have tried fastboot and I also tried Unrevoked, does not detect phone, have made sure usb debugging is on, any ideas - help and guidance will be appreciated.
Phone Info:
BRAVO PVT1 SHIP S-ON
HBOOT 0.93.0001
MICROP 031d
RADIO 5.11.05.27
Android Version 2.2
Baseband 32.49.00.32U-5.11.05.27
so your micro usb port on your phone is damaged and cannot transfer data?
that method won't work
"#NOTES: MUST BE BOOTED INTO ROM, ONLY TESTED ON FROYO AND S-OFF"
you can't do step 7, because step 6 will fail. it can't flash a recovery because you are not s-off yet.
have you installed all the relevant drivers for the phone to be detected? install htc sync, then uninstall it but leave the htc drivers.
at a minimum you will need your phone to be recognised by PC. then use revolutionary to s-off. follow the guides.
Hi
Thanks for the reply's. It may be that the USB port is damaged.
I have installed HTC Sync and uninstalled it,not removing the drivers.
Is there a way to root without USB, say using the micro SD card?
ldp04180 said:
Hi
Thanks for the reply's. It may be that the USB port is damaged.
I have installed HTC Sync and uninstalled it,not removing the drivers.
Is there a way to root without USB, say using the micro SD card?
Click to expand...
Click to collapse
not sure to be honest. so when you connect, computer can't see it or connect at all, you can't browse your sd card? it still charges though, so usb port is not completely broken.
have you tried another micro usb cable / laptop with drivers installed / sd card just to be sure?
you will almost certainly need it to be detected by pc to s-off/root etc. the software needs to communicate with the phone. have another look at the guides to see if they have another workaround.
Hi
Used another cable to check computer connection, still no joy, phone not recognized and does not charge phone anymore
I have read the guides, they all want PC access, do just asking if anyone knew of a different solution?
ldp04180 said:
Hi
Used another cable to check computer connection, still no joy, phone not recognized and does not charge phone anymore
I have read the guides, they all want PC access, do just asking if anyone knew of a different solution?
Click to expand...
Click to collapse
well if your phone doesn't charge anymore you need to look at the bigger picture. you need a working usb port regardless, at a minimum to charge the device! even if you s-off / root etc if it's not going to last one charge!
send for repair if it's under warranty, or find out how much it would cost for someone to repair it. there are probably guides out there to change it yourself if you're adventurous.
once it's repaired and working, you can s-off root etc properly
eddiehk6 said:
well if your phone doesn't charge anymore you need to look at the bigger picture. you need a working usb port regardless, at a minimum to charge the device! even if you s-off / root etc if it's not going to last one charge!
send for repair if it's under warranty, or find out how much it would cost for someone to repair it. there are probably guides out there to change it yourself if you're adventurous.
once it's repaired and working, you can s-off root etc properly
Click to expand...
Click to collapse
ok, thank you for your advice.

Categories

Resources