I just decided last night to switch from Calkulin to Blazer so I could try it out.
The results were disastrous.
I took my phone, which was running on Rogue Desperado Kernel, EL29 Modem, Calk 2.8.1, and backed up everything. Then I booted into ROGUE recovery, and flashed CALKS FORMAT ALL. This was a success.
Then I flashed BLAZER ROM 3.7. This was a success, according to my little black and green screen.
**HOWEVER, upon reboot I was stuck at SAMSUNG GALAXY S II screen. I waited...and waited...and waited. It never moved past this screen.
Then I tried booting into recovery - no dice. I had to download the Stock EL29 Kernel/Modem/ROM ODIN Full Restore and flash everything back to square one.
Once this was completed, I rooted using the Auto Rooter and took my phone to EL29 with CWM. Then I flashed my Kernel over to the stock EL29 with Rogue Kernel (this is easier to use than stock CWM IMO).
FINALLY, I booted into recovery, flashed CALK FORMAT ALL, then flashed BLAZER ROM 3.7. Now I'm back to the ** from earlier in this post - SAMSUNG GALAXY SII is on the screen, and I can't get past it or boot into recovery.
I'm going to run through the steps again to bring my phone back to stock, but I'd really like to try this ROM out. Does anyone have any ideas?
Any help is greatly appreciated.
With no background information, it sounds like it may have been a bad download. Have you tried downloading another copy of Blazer rom?
The process you described was correct, and sometimes bad downloads lead to infinite splash screens.
jyaworski said:
With no background information, it sounds like it may have been a bad download. Have you tried downloading another copy of Blazer rom?
The process you described was correct, and sometimes bad downloads lead to infinite splash screens.
Click to expand...
Click to collapse
+1. Definitely sounds like a bad download
jyaworski said:
With no background information, it sounds like it may have been a bad download. Have you tried downloading another copy of Blazer rom?
The process you described was correct, and sometimes bad downloads lead to infinite splash screens.
Click to expand...
Click to collapse
OK it looks like you correct. I re-installed Calk 2.8.1 with no issues and did a restore through Titanium. I then got a message saying "download incomplete" of BLAZER ROM. It's odd, because the download went through fine yesterday and the notification cleared before I booted into Recovery to flash everything.
Now I'm trying to re-download the ROM and the link is down with no mirror. Does anyone have a copy saved that they can create a mirror with?
webbiam said:
I just decided last night to switch from Calkulin to Blazer so I could try it out.
The results were disastrous.
I took my phone, which was running on Rogue Desperado Kernel, EL29 Modem, Calk 2.8.1, and backed up everything. Then I booted into ROGUE recovery, and flashed CALKS FORMAT ALL. This was a success.
Then I flashed BLAZER ROM 3.7. This was a success, according to my little black and green screen.
**HOWEVER, upon reboot I was stuck at SAMSUNG GALAXY S II screen. I waited...and waited...and waited. It never moved past this screen.
Then I tried booting into recovery - no dice. I had to download the Stock EL29 Kernel/Modem/ROM ODIN Full Restore and flash everything back to square one.
Once this was completed, I rooted using the Auto Rooter and took my phone to EL29 with CWM. Then I flashed my Kernel over to the stock EL29 with Rogue Kernel (this is easier to use than stock CWM IMO).
FINALLY, I booted into recovery, flashed CALK FORMAT ALL, then flashed BLAZER ROM 3.7. Now I'm back to the ** from earlier in this post - SAMSUNG GALAXY SII is on the screen, and I can't get past it or boot into recovery.
I'm going to run through the steps again to bring my phone back to stock, but I'd really like to try this ROM out. Does anyone have any ideas?
Any help is greatly appreciated.
Click to expand...
Click to collapse
The EXACT same thing happened to me and I did the same as the OP. I followed the instructions, I thought, verbatim. I'm not a newb when it comes to flashing, I've been doing this for years. Stupid me, I flashed a ROM and locked up the phone for a few hours until I got home from work. The only thing that brought it back was Odin to stock and start all over. The only roms that work for me are cal's rooted stocks, his custom roms and strong Steve's Smurf love ROM. Such is life.
was trying to download the new blazer rom and seems the link is broken so will try later.
PhantomHacker is having issues with his host (see quote below), I'm sure he'll have it handled asap. Blazer ROM is awesome, hope you guys enjoy once he gets it back up and running.
PhantomHacker said:
Having problems with my host... -_- Working on getting this back up.
Sent from my SPH-D710 using XDA App
Click to expand...
Click to collapse
Im not sure if you are or not but if you are trying to download the rom from your phone that is the first mistake. I have had allot of bad luck doing it this way. Always download it from the computer and never transfer it through Kies air always use a usb cable. I cannot tell you how much trouble I have run into when trying to download from the phone or transfer roms/themes wireless.
PH's site is back. Download to PC
OK I'm all good. Someone posted a mirror last night for the Blazer Rom (nibrwr notes that PhantomHacker's site is back up today for anyone else trying to download) and I downloaded it on my phone.
rbtrucking - I know you mentioned to always download on PC and transfer, but I've had almost no issues with the downloads direct to the phone. I did all of the Calk install when I first rooted this way, and the Blazer issue was probably my own fault, I must have ended the download before the file finished and then tried to Flash it.
I downloaded the full Blazer Rom on my phone directly yesterday and flashed it in Recovery and it worked fine.
Everything is working perfectly, and I've got it overclocked to 1.35GHZ. Stable as all hell and pulling over 5,000 on Quadrant, whatever the hell that test is good for.
Thanks for the help everyone.
Related
Posting this here because it wont let me post in the development forum.
Downloaded Legendary Rom 2.2, rebooted into Clockwork, wiped cache and Dalvik x3 each, installed Rom, rebooted....just sits at Samsung logo. I gave it a while in case it was just slow or something and then pulled battery, went back into clockwork, and tried installing a different kernel (the newest Samurai) in case that was the problem. Same thing happens except there is now a blue progress bar below the samsung logo. any suggestions to get it to work? I am installing legendary 2.1 now to see if that works.
DaveWW00 said:
Posting this here because it wont let me post in the development forum.
Downloaded Legendary Rom 2.2, rebooted into Clockwork, wiped cache and Dalvik x3 each, installed Rom, rebooted....just sits at Samsung logo. I gave it a while in case it was just slow or something and then pulled battery, went back into clockwork, and tried installing a different kernel (the newest Samurai) in case that was the problem. Same thing happens except there is now a blue progress bar below the samsung logo. any suggestions to get it to work? I am installing legendary 2.1 now to see if that works.
Click to expand...
Click to collapse
Reflash the rom again. If still the same issue, then download the rom from a computer and compare the MD5 checksums to make sure you have the entire file. Read a few pages back in that thread to get the MD5 checksum and use something like: http://portableapps.com/apps/utilities/winmd5sum_portable
The progress bar appeared at the Samsung screen after your kernel update because that particular kernel added that.
What did you have installed prior to installing Legendary ROM, some people have reported issues if they weren't on gingerbread prior to flashing. Try flashing back to stock, upgrading to gingerbread ota, reroot with Odin and then reflash. I'm working on Legendary ROM 2.2, works well, but have some issues with the screen turning off and not coming back on. 2.1 was flawless for me though. Might go back.
njett said:
What did you have installed prior to installing Legendary ROM, some people have reported issues if they weren't on gingerbread prior to flashing. Try flashing back to stock, upgrading to gingerbread ota, reroot with Odin and then reflash. I'm working on Legendary ROM 2.2, works well, but have some issues with the screen turning off and not coming back on. 2.1 was flawless for me though. Might go back.
Click to expand...
Click to collapse
I think that is a Samurai 3.0 kernel issue. Try Shadow kernel.
Sent from my SPH-D700 using XDA App
i must relay this...shadowkernel is awsome. as they have said above. odin back to ec05 and start from scratch. it sound like you have a semi-soft brick issue.
I get that when I try copying the ROM file through my network or a slow connection, meaning a bad file. Another person got this almost everytime because his sd card was going bad and needed reformatting. Everytime he flashed it transmitted bad data through recovery. He reformatted sd card and no more problems. But first try a redownload as suggested.
So I got my new Phone In the mail today because my other Epic 4g touch broke.
First thing I do is Load The latest ACS One Click Root/Restore For EL29 and all goes well. Now Im wanting to Load a Custom Rom, so Now i need a Recovery, So I use the E4G Autoloader to Load CWM and all goes well.
Boot into CWM, flash the ROM...reboot and it gets stuck at the Samsung Galaxy S screen.
I have tried restoring to EL29, EL26, EK02 and then insalling CWM, and all goes well up untill the point of rebooting from ANY ROM flash.... it just stays at the Samsung Galaxy S screen. Tried with CWM and Various other CWM5 variants.
Has any one seen this before? My last 4g touch did nothing like this.
Chris
So here I sit with a Stock Rooted Kernal/Rom (EL29) afraid to load CWM and flash any Rom because it always gets stuck at the Samsung Galaxy S Screen.
Really wanting a custom rom....
have you tried to use calkulins format all file before flashing the rom? if not try this link it should download it for you.
http://forum.xda-developers.com/attachment.php?attachmentid=771828&d=1320435068
Yes, I have it loaded on my SD card and use it every time. Iv tried so many combinations.. This is the first time I have had any problem with anything... Hero, Epic, Photon, 1st Epic Touch
This could be a re-man Phone because I got it via Insurance when my last one broke....think they could have done something to it?...even so I can ODIN/Restore to any EK02, EL26/29 and everything is fine.
I'd say I would be good with it cause they come rooted when using the ACS One Click, but I want a custom rom.
Chris
Sorry man then I don't know how to help you. That's the best I have for you. Best of luck ;-)
Sent from my GT-i9100 using xda premium
boostedmach said:
So here I sit with a Stock Rooted Kernal/Rom (EL29) afraid to load CWM and flash any Rom because it always gets stuck at the Samsung Galaxy S Screen.
Really wanting a custom rom....
Click to expand...
Click to collapse
Don't use the one click root method just use Odin to root the phone. Make sure your downloads are good by checking your md5. Another question for you how long are you waiting when it that screen pops up because the first boot takes a while as you may already know. Forgot to ask did you wipe your SD card when you got your new phone you could try that as well.
Gonna try to ODIN a 100% Stock rom, then go from there.
Looks like I found a EG30 Stock ROM, think that would be a good start?
Found http://forum.xda-developers.com/showthread.php?t=1415884
Going to ODIN that, then go from there.
Chris
boostedmach said:
Found http://forum.xda-developers.com/showthread.php?t=1415884
Going to ODIN that, then go from there.
Chris
Click to expand...
Click to collapse
There is a ek02 rom
Well that failed in ODIN...
Would an EK02 be better to start out with?
Do you have a Google plus account
Yes I have a Google Plus account
boostedmach said:
Yes I have a Google Plus account
Click to expand...
Click to collapse
Sign in lets get this phone running a custom rom. My name is shawn
I have a Stock EL26 w/Root
I also ODIN'd StockAS5-EL26 Repack from Chris41g
And all is happy...but im affraid to try and Load any custom Rom via Recovery because nothing has ever worked so far. Online Stock Roms via Odin have worked.
I have read about a few others getting stuck at the Samsung Galaxy S Screen, but i dont know what they have done if anything.
Chris
smccall said:
Sign in lets get this phone running a custom rom. My name is shawn
Click to expand...
Click to collapse
I assume your talking about signing in online?
my user name is this user name @gmail.com
Chris
boostedmach said:
I assume your talking about signing in online?
my user name is this user name @gmail.com
Chris
Click to expand...
Click to collapse
OK looking now
So Weird.
Stock EL26, Rooted fine, Installed chris41g repack with ACS Recovery, Flashed the EL29 Modem went fine.
Wanting to use Calkulin E4GT v2.8 or TNz BLEND
boostedmach said:
So Weird.
Stock EL26, Rooted fine, Installed chris41g repack with ACS Recovery, Flashed the EL29 Modem went fine.
Wanting to use Calkulin E4GT v2.8 or TNz BLEND
Click to expand...
Click to collapse
Can't find you on Google
Im on my google+ page and logged into gmail.
boostedmach said:
So Weird.
Stock EL26, Rooted fine, Installed chris41g repack with ACS Recovery, Flashed the EL29 Modem went fine.
Wanting to use Calkulin E4GT v2.8 or TNz BLEND
Click to expand...
Click to collapse
Boosted Into Recovery, flashed Calkulin E4GT Format All, Then Flashed Calkulin E4GT v2.8... Rebooted
Now stuck at the Samsung Galaxy S Screen.
Checked MD5 for the rom.
On a side note, The flash went pretty fast in recovery and the precentage bar did not work, Dont remember how long a ROM normally takes in to flash in Recovery but Its almost 300mb and it went pretty fast.
Chris
I just upgraded my E4GT Sprint from GB to ICS using the oneclick installer. I am trying to install the CODENAME rom from CWM but havng issues getting CWM installed. I used the the E4GT auto but FE16 isnt listed so i tried FE15 but it wont load into CWM. So i tried this link "http://forum.xda-developers.com/showthread.php?t=1390393" and flashed from ODIN and it goes into CWM but before it boots it says my phone is a gt-i9100 and has a ! on the bottom. It appears to boot though so i booted back into CWM and tried to flash the ZIP for CODENAME and the gapps file and it jsut gets stuck at the boot screen with the transformer logo. I cant get into CWM after that point and have to ODIN back to ICS. I am on ICS now and its working fine. Does anyone have any instructions on getting CWM installed and the codename rom from a fresh odin ICS install?
mazdaspeed6 said:
I just upgraded my E4GT Sprint from GB to ICS using the oneclick installer. I am trying to install the CODENAME rom from CWM but havng issues getting CWM installed. I used the the E4GT auto but FE16 isnt listed so i tried FE15 but it wont load into CWM. So i tried this link "http://forum.xda-developers.com/showthread.php?t=1390393" and flashed from ODIN and it goes into CWM but before it boots it says my phone is a gt-i9100 and has a ! on the bottom. It appears to boot though so i booted back into CWM and tried to flash the ZIP for CODENAME and the gapps file and it jsut gets stuck at the boot screen with the transformer logo. I cant get into CWM after that point and have to ODIN back to ICS. I am on ICS now and its working fine. Does anyone have any instructions on getting CWM installed and the codename rom from a fresh odin ICS install?
Click to expand...
Click to collapse
You really should read more before hopping around like that without checking. Real risk for a brick here.
-Flash EL26 stock CWM kernel via the PDA option in ODIN/Mobile ODIN
-When phone begins reboot, Hold Power + Volume up until boots into recovery.
-Wipe data/factory, cache and dalvik cache
-Flash ROM
-Flash Gapps
-Reboot
Those are the instructions right from the developer's thread. This is an AOSP rom and it sounds like you're trying to install TW kernels.
http://forum.xda-developers.com/showthread.php?t=1662295
This is the kernel repository. It links to each kernel where you can read further and find out if they are safe for flashing things.
Seems like you've done a bunch of stuff. But you really should do a whole bunch of reading first or you will brick your phone.
My suggestion would be to use sfhub's one-click http://forum.xda-developers.com/showthread.php?t=1705730 to get to a fully stock rooted device. Then use his autoroot package http://forum.xda-developers.com/showthread.php?t=1342728 to add CWM (the lates in the package is FF11+CWM Agat I believe) then you can add Agat's latest kernel with CWM http://forum.xda-developers.com/showthread.php?t=1721065
But I would be very careful when flashing ANY ROM; use the developers prefered method. Some recommend using EL26 CWM. Some a different recovery or procedure. Be especially careful with CM9 and AOKP builds to follow the directions there.
Good luck
So while i was waiting for a response i just went back to the stock GB using the one click install. I then used the autoroot package to install CWM and then restored my nandroid backup before i made in the very beginning. So my phone is back to a perfect state with GB and CWM installed. Can i just flash the ROM from CWM as is then? For some reason i thought it had to be "converted" to ICS and thats what started this whole mess. Things have changed since my old Evo
I just noticed that im running EL29 not 26...does that matter? When i try to flash that CMW EL26 stock root is when it gave me that gt-i9100 on boot and the ! at the bottom. Using the autoroot and choosing the EL29 Rogue is the only way i got it installed.
mazdaspeed6 said:
So while i was waiting for a response i just went back to the stock GB using the one click install. I then used the autoroot package to install CWM and then restored my nandroid backup before i made in the very beginning. So my phone is back to a perfect state with GB and CWM installed. Can i just flash the ROM from CWM as is then? For some reason i thought it had to be "converted" to ICS and thats what started this whole mess. Things have changed since my old Evo
I just noticed that im running EL29 not 26...does that matter? When i try to flash that CMW EL26 stock root is when it gave me that gt-i9100 on boot and the ! at the bottom. Using the autoroot and choosing the EL29 Rogue is the only way i got it installed.
Click to expand...
Click to collapse
My friend some good suggestions above your post. Give yourself a day or two and do some reading prior to flashing. This way you may not end up at Sprint making up stories about why your phone wont boot up.
Let me just echo what everybody else has said, you're gotta read more. A lot more! If you're one goal is to get CNA in your phone I would recommend reading all of the very first post on that thread. They give step by step instructions.
If you need CWM there are several options to get it on your phone. Both sfhub and I have put together several one-click and automated options to get it on your phone.
One thing that hasn't been suggested yet but I would strongly encourage you to do is to read the "How Not To Brick Your E4GT" thread. It's sticked in the General section.
Good luck!
Two more things.
1) If you're going to ask for help give it a few minutes before trying something new. It takes people a minute to reply. Sometimes waiting that extra minute or two is all you need to be saved from bricking.
2) Don't be afraid to hit your thanks button for everyone who has offered advice already. I got them once for you but it might not hurt to do it again.
Hello,
Am presently running AOKP Milestone 6 with TWRP recovery & want to flash the Blazer ICS ROM. QBKing77 suggests flashing Blazer from CWM 5.0.2.7, but I'm not sure how to install CWM from TWRP. I am thinking I simply need to download the tar file to my SD card, then flash via Mobile Odin. Not sure that's correct or where that will leave me...
Also thought maybe I can flash CWM as a zip from TWRP. Again, not sure that's correct or where that will leave me either.
Any definitive help would be appreciated. Been reading for hours! Thanks so much!
I have the same problem/issue, would welcome some advice. Previously bricked (BLOD) now new phone, don't want to relive that experience.
snkycool said:
I have the same problem/issue, would welcome some advice. Previously bricked (BLOD) now new phone, don't want to relive that experience.
Click to expand...
Click to collapse
Keep in mind though that this is the Epic 4G Touch forum. Looks like you might be running an EVO? Just a heads up...
not any more, profile up date. I was running a Blazer rom, then flashed another rom and did not pay attention and BLOD. Gonna stick w/Phantom ROM unitl this brick then getsfixed, but would love to use TWRP.
After some discussion in agats thread (http://forum.xda-developers.com/showthread.php?t=1767421), I decided on the following method of installing agat recovery & flashing the Blazer ICS ROM, & it worked like a charm:
1- download newest agat kernel from OP & install on sd
2- flash agat kernel using Mobile Odin
3- as soon as splash screen appears on reboot, pull battery
4- power up into new agat recovery, wipe, & flash ROM
On a side note, just to be super safe, I used Calkulin's Format All instead of manually wiping.
These are the steps simplified. If anyone needs more detail, just ask. Thanks! Hope that helps someone...
Thanks to QBKing77 for the many videos from which I gathered enough info to give this method a shot, & agat63 for your support!
I recently went back to stock F127, then manually flashed the FL24 update via mobile odin, now phone constantly freezes an reboots every few seconds!! Is there any fix for this at all?? Should i attempt to revert back to F127 if possible?
dougthemug said:
I recently went back to stock F127, then manually flashed the FL24 update via mobile odin, now phone constantly freezes an reboots every few seconds!! Is there any fix for this at all?? Should i attempt to revert back to F127 if possible?
Click to expand...
Click to collapse
If you are on stock unrooted FL24, go into stock recovery and wipe cache partition.
BluesRulez said:
If you are on stock unrooted FL24, go into stock recovery and wipe cache partition.
Click to expand...
Click to collapse
I'm having a similar issue. But was on FI27 with random reboots and an overly sensitive power button and then sometimes will take a few presses to turn on the screen. I rooted and the reboots seemed to have gotten much more frequent. I'm now on CyanogenMod 10.1 and it's happening just as much.
Will that work for me as well? If so, how do I wipe my cache partition?
BluesRulez said:
If you are on stock unrooted FL24, go into stock recovery and wipe cache partition.
Click to expand...
Click to collapse
No...it was FL24 with root (Qb king) the trouble began when i attempted to flash agat cwm thru mobile odin, thats when phone went nuts. Was able still to use odin mode to revert back to stock F127 which fixed dillema, but am now stuck searching for workaround as in a different kernal -w- cwm as in the earlier odin releases like FF18 which included options like root/w/cwm, or different cwm tar thats compatible with mobile odin......
dougthemug said:
No...it was FL24 with root (Qb king) the trouble began when i attempted to flash agat cwm thru mobile odin, thats when phone went nuts. Was able still to use odin mode to revert back to stock F127 which fixed dillema, but am now stuck searching for workaround as in a different kernal -w- cwm as in the earlier odin releases like FF18 which included options like root/w/cwm, or different cwm tar thats compatible with mobile odin......
Click to expand...
Click to collapse
Same thing happened to me after I flashed Agat recovery. I had to re-root my phone to fix the rebooting but now I don't know which recovery to use. :/
I haven't had any issues running Kubans FL24 kernel at all. Check this thread.
http://forum.xda-developers.com/showthread.php?t=2139013
Kernel with recovery here:
http://forum.xda-developers.com/showthread.php?t=
Sent from my Blu Kuban v0.2.5 FL24 E4GT SGS2 SPH~D710 (and whatever else they can call this phone) using Tapatalk 2
I have 2 phones and they both have the same issue. Right after the fl24 update. Sprint wont help at all. Any idea how to fix. Or I have to install a new rom?
Fl24 is the ics ota that sprint has pushed out. Not good. You best get away from ics, consider leaked Jb GB08 by sextape :thumbup: in dev section.
Crank up your PC, download GB08 one click stock/rooted restore, put your phone in download mode and hit start.
You're going to fall in love with your phone all over again. :thumbup::thumbup::beer:
DO NOT USE "NO DATA" you cannot keep your borked up ics data, this needs to be wiped clean, hence rooted restore.
You can only use "no data " after you are on Jb. Coming from ics you need full wipe and the one click "restore " does that.
Copy your internal and external SD's to a folder on your PC, then do the one click. :thumbup::thumbup::thumbup:
Before you ask, there is no safe recovery for Jb yet, and using a GB recovery involves flashing back to gingerbread, then flashing back, don't go there. Official Jb rec is just around the corner, maybe a month or less. :what:
Enjoy the jelly beans!!
Pp. :beer::thumbup:
Transmitted from another galaxy with a Jellybean infused P-5113 full of Unicorn porn.
PanchoPlanet said:
Fl24 is the ics ota that sprint has pushed out. Not good. You best get away from ics, consider leaked Jb GB08 by sextape :thumbup: in dev section.
Crank up your PC, download GB08 one click stock/rooted restore, put your phone in download mode and hit start.
You're going to fall in love with your phone all over again. :thumbup::thumbup::beer:
DO NOT USE "NO DATA" you cannot keep your borked up ics data, this needs to be wiped clean, hence rooted restore.
You can only use "no data " after you are on Jb. Coming from ics you need full wipe and the one click "restore " does that.
Copy your internal and external SD's to a folder on your PC, then do the one click. :thumbup::thumbup::thumbup:
Before you ask, there is no safe recovery for Jb yet, and using a GB recovery involves flashing back to gingerbread, then flashing back, don't go there. Official Jb rec is just around the corner, maybe a month or less. :what:
Enjoy the jelly beans!!
Pp. :beer::thumbup:
Transmitted from another galaxy with a Jellybean infused P-5113 full of Unicorn porn.
Click to expand...
Click to collapse
Hi,
I'm in the process of rooting/finding a ROM for my Fiance's E4GT... I was hoping the latest OTA would fix the HORRIBLE battery life, but alas it has not. Not going to get into what all I've tried to fix the battery issue... short of another ROM (she's really not a "power user").
I looked for the thread you specified, but could only find the FJ10 build. It appears "sextape" is no longer a member here?
Only way I was able to find it was found this page from google:
http://www.xda-developers.com/android/official-jelly-bean-on-epic-4g-touch-fj10-released/
But when you click on the link provided in the news story that should take you to his member profile (to find all created threads, thus the GB808) it's gone.
The thread linked in that article is to the FJ10 build, which shows the OP as "guest" WTF is going on there?
Anyways, can you link me to ROM you've posted about. I'm just looking for something for her to get better battery life. Her phone stays off in her pocket at work all day (shows NO screen on time for 8-10 hours) however the battery is steadily declining with "Android OS" at fault. I've tried DS Battery and other apps, nothing can force the phone to sleep. Even done a full factory reset and disabled everything but basic 3g for web browsing (no other sync) and the battery still drains.
Thanks,
Jonathan
Here you go http://forum.xda-developers.com/showthread.php?p=37986593
Just follow the instructions in the op. Do some reading in thread all should be good.
Do not be distracted by the custom roms, not now, stick to stock for now.
Pp. :beer::thumbup:
sent from a jellybean filled epic touch.