Just wanted to see if there is any pics or video of the tmobile galaxy s2 tear down. Want to see what it looks like on the inside but don't want to do that to my device. Lol
Did a search but didn't have much luck! Can anyone help? Thanks!
Killing Zombies With My Samsung Galaxy S2
darkside79 said:
Just wanted to see if there is any pics or video of the tmobile galaxy s2 tear down. Want to see what it looks like on the inside but don't want to do that to my device. Lol
Did a search but didn't have much luck! Can anyone help? Thanks!
Killing Zombies With My Samsung Galaxy S2
Click to expand...
Click to collapse
Check over at ifixit.com they are beast in teardown repair and rebuild guides.
Sent from my Invincible Juggernaut!
Babyj303 said:
Check over at ifixit.com they are beast in teardown repair and rebuild guides.
Sent from my Invincible Juggernaut!
Click to expand...
Click to collapse
With Apple devices.. Not too much else
Sent from my T-Mobile Galaxy S II 4G
Maybe you can purchase something damaged at a reduced price.
- I bet a few repair shops have a FUBAR item in a box somewhere waiting for toxic-cycle.
Do you have any specific questions I tore mine apart and replaced the body. Its similar to the euro sgs2 except there is no screw directly holding the mobo in to.the chassis. If u need any specific pics I'll help u out
PJS
Sent from my SGH-T989 using xda premium
xspeed9190 said:
Do you have any specific questions I tore mine apart and replaced the body. Its similar to the euro sgs2 except there is no screw directly holding the mobo in to.the chassis. If u need any specific pics I'll help u out
PJS
Sent from my SGH-T989 using xda premium
Click to expand...
Click to collapse
where is the vibrator motor?
AznDud333 said:
where is the vibrator motor?
Click to expand...
Click to collapse
Where it is in all Galaxy S & SII phones. Next to the microphone in the cable that has the fixed bottom soft buttons, microphone, and wifi antenna connector. It is a complete assembly but you may be able to de-solder the vibrator from the assembly and replace it if you are careful and have one.
ChauncyG said:
Where it is in all Galaxy S & SII phones. Next to the microphone in the cable that has the fixed bottom soft buttons, microphone, and wifi antenna connector. It is a complete assembly but you may be able to de-solder the vibrator from the assembly and replace it if you are careful and have one.
Click to expand...
Click to collapse
is it hard to disassemble/reassemble this phone at all? any chance of putting up a full vid of disassembling it?
For you guys taking apart your phones... does it have an internal SWAPABLE SD card?
I know my AWS Dell Streak we were able to take it apart and replace the internal SD (micro SD card) with a larger sized one.
What about these phones?
Sent from my SGH-T989 using XDA App
Vinsane said:
For you guys taking apart your phones... does it have an internal SWAPABLE SD card?
I know my AWS Dell Streak we were able to take it apart and replace the internal SD (micro SD card) with a larger sized one.
What about these phones?
Sent from my SGH-T989 using XDA App
Click to expand...
Click to collapse
Bump!
Killing Zombies With My Samsung Galaxy S2
darkside79 said:
Bump!
Killing Zombies With My Samsung Galaxy S2
Click to expand...
Click to collapse
didnt take mine apart too far(because of the lack of a service manual, i didnt want to take apart things that i cant put back)
but it doesnt seem like that's possible
AznDud333 said:
didnt take mine apart too far(because of the lack of a service manual, i didnt want to take apart things that i cant put back)
but it doesnt seem like that's possible
Click to expand...
Click to collapse
Its possible....as soon as I get my hands on the white parts I'll open my phone up
tiguy99 said:
Its possible....as soon as I get my hands on the white parts I'll open my phone up
Click to expand...
Click to collapse
Its possible to change the internal sd card?
Sent from my SGH-T989 using xda premium
xsteven77x said:
Its possible to change the internal sd card?
Sent from my SGH-T989 using xda premium
Click to expand...
Click to collapse
Sorry guys...I miss read the post and posted out of context. please disregard my post above. I'm not sure if the internal sd can be replaced yet either but am eager to find out as well
I drop my phone and the side is all dent and scratched up. Is there any update on how to disassemble this phone yet?
Also is there a link on an oem housing replacement for the T989? I can't seem to find a thread in the accessories sub-forum regarding a new housing replacement. Thanks in advance.
I need some help
My bezel cracked. I have never dropped it, so I don't know how it happened. Samsung charges 100 dollars, but the OEM case with bezel is 17 dollars. Is it possible to replace the Bezel and not the whole screen / digitizer / bezel ?
The Samsung deal sounds good, but if it is just scratched... maybe live with it until you actually break it?
---------- Post added at 08:53 AM ---------- Previous post was at 08:41 AM ----------
I'll see if I can figure out how to do this...
I left this one on the bumper of my truck and went to the store, thirty minutes later, I found it in a busy road, face down. It was run over by a car as I went to pick it up. Whether two tires or 200, I don't know, but the screen was a total loss, and the bezel was so dented I wouldn't even try to put a new screen in it. The phone rang as I was holding it, so it still works. I replaced the whole screen assembly in five minutes, but it cost $170! Price gouging, I'm sure. Anyway, this housing is basically the real structure of the phone, made of metal and the screens are glued into it.
I don't recall seeing anything that looked like a replaceable internal SD card.
I took the old screen off the bezel, just out of curiosity, and it looks extremely difficult to remove any working part from the bezel without destroying it. The AMOLED and digitizer are very fragile, have connections running all around the edges which could be nicked and cause an open circuit, even using plastic tools. I'd recommend replacing broken digitizers or screens, but not broken bezels. I'm also unsure how a metal bezel breaks without cracking the screen, but that is beside the point. I've replaced a broken digitizer on a HTC EVO 4G, for a friend and it took about two hours, required some specialized industrial two sided tape (no foam!) and I risked damaging the AMOLED in that while doing it. Cost was $12.
I'll now try to post some photos.
Galaxy S2 T-Mobile T989 photos
Related
ok so I managed to crack the screen..nice big shatter mark under the screen and now the entire screen went black...insurance is a pain and from what I understand getting Asurion to replace my vibrant will be $130 and buying an AMOLED screen itself is cheaper.
The rest of the phone is still in working condition as before my screen went totally black after it broke some of it was still functional.
Any idea on where I can get the screen? I have not had luck on ebay as of yet, and was hoping someone here could recco a reputable vendor...
Aliexpress? aliexpress DOTcom/product-fm/342627474-Touch-Digitizer-LCD-Display-AMOLED-Screen-origianl-i9000-for-T-Mobile-Samsung-Vibrant-t959-Wholesale-wholesalers.html
Etech? etech DOTcom/cell-phones-lcd-screens--c1144_1156?page=3&m_id=12&sort=20a
www.cnn.cn maybe? it about $70 +sh
Wow wish I would had found this post sooner...
I dropped my vibrant from my and it was in the case.. it landed flat on the screen..glass did not break but AMOLED screen enploded.. I didnt know until i got to my car and tried to make a call. Crap...I dish out the $130.00 bucks ...bummed out about that..
oh man ...
Still great site and price. Thanks
Thanks I'll try cnn.cn. I see some decent reviews about them.
Is there a tutorial on how to replace this? Or would you have to get someone to do it?
Sent from my SGH-T959 using XDA App
noemberday said:
Is there a tutorial on how to replace this? Or would you have to get someone to do it?
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
youtube.. just search for it..
I cracked my screen also. I found that site after I put in the claim. So I figured what the hell and started taking it apart, for next time.
It isn't easy! I'm pretty nerdy and good with my hands. Be very careful and very patient. There are small parts and wires that can very easily break.
Sent from a Samsung Vibrant.
ok so I got the screen...and this thing is hard as hell to swap...anyone have any ideas? I dont want to further damage anything...
I did find this... http://www.careace.net/2010/06/09/disassembly-of-the-samsung-galaxy-s/
FYI incase anyone else is looking for where to buy from.
http://www.globaldirectparts.com/Samsung-T959-LCD-Digitizer-p/smsng6085995.htm
Have you had any luck with this?I own an Orange San Francisco and cracked the amoled,unfortunately orange or any other site/company offers any repair AFAIK. I'm looking into repairing it myself, are amoled connectors compatible from one phone to another or are they manufacturer specific if you are aware of? I know this is a long shot but it doesn't hurt asking.
Chrishas said:
Have you had any luck with this?I own an Orange San Francisco and cracked the amoled,unfortunately orange or any other site/company offers any repair AFAIK. I'm looking into repairing it myself, are amoled connectors compatible from one phone to another or are they manufacturer specific if you are aware of? I know this is a long shot but it doesn't hurt asking.
Click to expand...
Click to collapse
it would most likely have to be the same part
because the Galaxy S series are the only ones with that size AMOLED screen.
been there done that
i got a vibrant off of something awful for pretty cheap with a broken screen
first off you literally have to pry the screen off of the phone
and the bottom four buttons? there is a very thin ribbon cable that is glued to the screen
there are a few things youll need
1.really small screw driver (i got a glasses repair kit from the dollar store. worked great)
2.something to pry the screen off (used a screw driver from said kit)
3.balls. that ribbon cable is very very easy to break
first off you have to take apart the phone completely
i would even take off the one board that the screen connects to
then you need to pry off the screen very carefully
if your amold or whatever part is broken you're going to have to peel it off
it really sucks and makes you look like a bad 70s disco
after that it gets pretty simple
make sure you have something to hold the top and bottom part to the phone
mine isnt flush due to me being a jackass and not getting the right glue stuff to hold it down
after that it should work perfect like before
if anyone wants to trade me a new screen for the i9000 screen or buy me a screen (lol) i would make a very detailed video (not happy with the way the first attempt turned out)
post itt or pm me if you have any questions
So you are saying it should work,but what about the software part,won't there be any problems?
Chrishas said:
So you are saying it should work,but what about the software part,won't there be any problems?
Click to expand...
Click to collapse
what are you talking about
thenotoriouspie said:
what are you talking about
Click to expand...
Click to collapse
about replacing a phone screen using a screen from another model,but of the same size,resolution
thenotoriouspie said:
3.balls. that ribbon cable is very very easy to break
Click to expand...
Click to collapse
and thats what I screwed up....what are my options now? Try again? dont think I can.
scrizz said:
FYI incase anyone else is looking for where to buy from.
http://www.globaldirectparts.com/Samsung-T959-LCD-Digitizer-p/smsng6085995.htm
Click to expand...
Click to collapse
did you see (Minimum order): 2
130448356330 check out this item on ebay
I really need help. I got my phone apart w/ the board for speaker and camera off and the front speaker off. I did not remove the haptic feedback motor yet. how the hell do you actually pry the screen off. i just don't see a way.
will the international galaxy s screen work for vibrant they hace same shape compared to captivate. And I9000s screen is cheaper than T959 screen (based on ebay price)
I am ordering a new genuine OEM T-989 enclosure. I have seen a lot of people replace the screen digitizer combination. I have not seen any body remove the digitizer and screen from the bezel and mid frame.
Has anybody done this?
Does anybody have any information on this?
Any help would be greatly appreciated.
Sent from my SGH-T989 using Tapatalk 2
shnn2011 said:
I am ordering a new genuine OEM T-989 enclosure. I have seen a lot of people replace the screen digitizer combination. I have not seen any body remove the digitizer and screen from the bezel and mid frame.
Has anybody done this?
Does anybody have any information on this?
Any help would be greatly appreciated.
Sent from my SGH-T989 using Tapatalk 2
Click to expand...
Click to collapse
I was going to do this till I see how difficult it is. It is almost impossible to separate the bezel from the digitizer with out breaking the screen. YouTube it.
Sent from my Galaxy SII T-mobile using xda premium
yeislak said:
I was going to do this till I see how difficult it is. It is almost impossible to separate the bezel from the digitizer with out breaking the screen. YouTube it.
Sent from my Galaxy SII T-mobile using xda premium
Click to expand...
Click to collapse
not true, all you need is a heat gun/blow dryer and a steady hand + a pry tool.
KillaHurtz said:
not true, all you need is a heat gun/blow dryer and a steady hand + a pry tool.
Click to expand...
Click to collapse
Any advice on temperature settings and adhesive replacement / pry tool?
Sent from my SGH-T989 using Tapatalk 2
I got sand paper and took all the chrome off the bezel. Come to find out the plastic is a matte black. Looks sick and my phone doesn't look like crap anymore. Looks brand new. Will post pics later if interested.
Sent from my AOKP-T989 using xda premium
yeislak said:
I got sand paper and took all the chrome off the bezel. Come to find out the plastic is a matte black. Looks sick and my phone doesn't look like crap anymore. Looks brand new. Will post pics later if interested.
Sent from my AOKP-T989 using xda premium
Click to expand...
Click to collapse
What grain sand paper did you use? And any special technique in the sanding process?
Ayodeji13 said:
What grain sand paper did you use? And any special technique in the sanding process?
Click to expand...
Click to collapse
P600 I believe. I know it was 600 tho. And no technique I didn't even take the phone apart. I took the battery door off and make sure you have a screen protector on so you don't f up your ****. Just rub he paper hard on the bezel don't be afraid. It will take about 30 to 45 min maybe an hour with breaks cus your fingers will start to burn. Use a gloves they'll help.
Sent from my AOKP-T989 using xda premium
I'm at the doctors when I get out I'll put up some pics so you can see what it looks like before you do it. Also be careful you don't get to much the dusted paint in any port.
Sent from my AOKP-T989 using xda premium
here you go
I have been thinking that if it is impossible, could you not just sand off the bezel, then Dremel out the inside screen mount of the new frame and finally epoxy the new bezel where the old bezel used to reside with plastic epoxy?
I asked some expert phone repair guys at the CPR Cell Phone Repair franchise; and they said that the screen will never ever ever ever come off unless you are either a machine or really good. They stated that they would not be able to guaranty the screens safety especially considering the heat involved.
If it is done by Samsung at all without replacing the entire digitizer and screen combo I would assume they use some kind of vacuum suction cup to pull off the screen after the proper amount of heat is applied.
Or, we could just paying Samsung the quoted 100 dollars to have it done.
This is non warranty work, so does anyone think they will mind if the phone is rooted?
Here is where you can order parts.
I don't know if they are genuine.
http://www.parts4repair.com/samsung-galaxy-s-ii-t989/
shnn2011 said:
I have been thinking that if it is impossible, could you not just sand off the bezel, then Dremel out the inside screen mount of the new frame and finally epoxy the new bezel where the old bezel used to reside with plastic epoxy?
I asked some expert phone repair guys at the CPR Cell Phone Repair franchise; and they said that the screen will never ever ever ever come off unless you are either a machine or really good. They stated that they would not be able to guaranty the screens safety especially considering the heat involved.
If it is done by Samsung at all without replacing the entire digitizer and screen combo I would assume they use some kind of vacuum suction cup to pull off the screen after the proper amount of heat is applied.
Or, we could just paying Samsung the quoted 100 dollars to have it done.
This is non warranty work, so does anyone think they will mind if the phone is rooted?
Click to expand...
Click to collapse
The pictures above you post is what I did to my phone. I sanded the bezel without even taking it apart.
Sent from my SGH-T989 using xda premium
The Bezel is part of the frame I believe. I would bet allot of money you can't get the screen of without cracking the digitizer. But, heat the top and bottom, that is where the greatest concentration of adhesive is. And watch the ribbon to the capacitive buttons because they will be stuck to the screen. You will have to disconnect them.
Sent from my SGH-T989D using xda premium
yeislak said:
here you go
Click to expand...
Click to collapse
That looks pretty cool dude. I have a question for you tho. How did you set the DPI so high? Your icons are small and thats how I want mine to be except whenever I use the DPI app from the market, it causes problems with parts of the ROM. For example the google search bar will only go halfway across the screen.
yeislak said:
here you go
Click to expand...
Click to collapse
That looks badass. Wanna do it to mine since you in Miami? jk lol
yeislak said:
here you go
Click to expand...
Click to collapse
Is that android bot doing the Hokey Pokey?
The Team Infamous project is up and running. http://www.infamousdevelopers.com
Sent from my SGH-T989 using Tapatalk 2
I just got my replacement about a week ago. I bought this phone used and without the battery door. Scuffs included. Luckily I kept the screen immaculate. None the less now that I have a mint handset and bought a battery door... the T989 sure is a smexy fellow. IMO the best looking Galaxy s2. Too bad we never got the Exynos and had to settle for the much slower s3 SoC. I:-/
Sent from my SAMSUNG-SGH-T989 using xda premium
RushAOZ said:
I just got my replacement about a week ago. I bought this phone used and without the battery door. Scuffs included. Luckily I kept the screen immaculate. None the less now that I have a mint handset and bought a battery door... the T989 sure is a smexy fellow. IMO the best looking Galaxy s2. Too bad we never got the Exynos and had to settle for the much slower s3 SoC. I:-/
Sent from my SAMSUNG-SGH-T989 using xda premium
Click to expand...
Click to collapse
Were running at 1.5 Ghz everyone else is at 1.2Ghz.
Sent from my SGH-T889 using Tapatalk 2
Site back up
The infamous website is back up.
http://www.infamousdevelopers.com
Hi
My partner has cracked the glass on the screen of her note 2. I was going to fix it for her but I'm looking for somone with experience fixing the note 2. I recently fixed a cracked screen on my galaxy s 3 by replacing just the glass on the front and using the same lcd etc. It only cost me £25. Is the same repair possible on the note 2 or is it constructed differently? I've had a look online and you can buy the glass from various places.
Thanks
Steve
steevwatson said:
Hi
My partner has cracked the glass on the screen of her note 2. I was going to fix it for her but I'm looking for somone with experience fixing the note 2. I recently fixed a cracked screen on my galaxy s 3 by replacing just the glass on the front and using the same lcd etc. It only cost me £25. Is the same repair possible on the note 2 or is it constructed differently? I've had a look online and you can buy the glass from various places.
Thanks
Steve
Click to expand...
Click to collapse
Did the new replacement fit perfectly as it was before?
Sent from the Rabbit Hole
Unfortunately, the glass is glued onto the touchscreen which makes it more difficult. Though I've seen somebody posting about fixing it anyway, involving a heat gun to get the glue off, but couldn't find the post on Tapatalk. Perhaps if you search around.
Sent from my GT-N7100 using Tapatalk 2
bushako said:
Did the new replacement fit perfectly as it was before?
Sent from the Rabbit Hole
Click to expand...
Click to collapse
In my galaxy s3 it looked good as new.
Thanks
Steve
adytum said:
Unfortunately, the glass is glued onto the touchscreen which makes it more difficult. Though I've seen somebody posting about fixing it anyway, involving a heat gun to get the glue off, but couldn't find the post on Tapatalk. Perhaps if you search around.
Sent from my GT-N7100 using Tapatalk 2
Click to expand...
Click to collapse
On the GS3 the glass was only glued around the edges of the touchscreen. I was hoping it was the same for the note. I'll have an other look online everything I found for the note was about replacing the whole screen. Loads of info and vids for replacing the galaxy s 3 glass tho. Thats what made me wonder if it was more complicated for the note. I'm still tempted to try it. Worst case is I have to replace the whole screen which I would have to do anyway
Thanks
Steve
Let me know if you are doing this soon
I have gathered all the pieces and tools to repair mine (glass lens, heat gun, pry tools, etc) and have planned to do it on wednesday.
However, I could not find anyone on the internet that have acheived it yet. I hope it's possible
Here's a useful video that may help: http://www.youtube.com/watch?v=bxgZeb5QytM
Here is my redneck method. You may need a bigger knife.
http://forum.xda-developers.com/showthread.php?t=2039145
---------- Post added at 09:42 PM ---------- Previous post was at 09:41 PM ----------
steevwatson said:
On the GS3 the glass was only glued around the edges of the touchscreen. I was hoping it was the same for the note. I'll have an other look online everything I found for the note was about replacing the whole screen. Loads of info and vids for replacing the galaxy s 3 glass tho. Thats what made me wonder if it was more complicated for the note. I'm still tempted to try it. Worst case is I have to replace the whole screen which I would have to do anyway
Thanks
Steve
Click to expand...
Click to collapse
Lucky, mine was glued 100% on the AMOLED display and all. I managed to fix it though, be careful when applying the new superglue to hold the new display as I put in too much and it bled over onto the display surface.
Inach said:
Here's a useful video that may help: http://www.youtube.com/watch?v=bxgZeb5QytM
Click to expand...
Click to collapse
Thanks, this is a change of Digitizer+Glass and the guy wrotes : "Its not possible to replace the glass only without special equipment,"
So,it might not be possible to only un-glue the glass as we see video for S3
nickanderson said:
I was thinking of getting this case, does anyone have this? If so, what do you think?
ww w.ion-factory.com/predator_note2.php
broke link due to being new
Click to expand...
Click to collapse
And what would "special equipment" be? If it's only a heat gun, then great. But if it needs a clean room with robotic arm, well not so great.
Sent from my GT-N7100 using Tapatalk 2
G.Reaper said:
And what would "special equipment" be? If it's only a heat gun, then great. But if it needs a clean room with robotic arm, well not so great.
Sent from my GT-N7100 using Tapatalk 2
Click to expand...
Click to collapse
good question. If the screen is broken anyway and my Mrs lets me i'm tempted to give it a go. surely worst thing that happens is I'll need to buy a new screen which I would have to do anyway if I don't try.
Thanks
Steve
steevwatson said:
good question. If the screen is broken anyway and my Mrs lets me i'm tempted to give it a go. surely worst thing that happens is I'll need to buy a new screen which I would have to do anyway if I don't try.
Thanks
Steve
Click to expand...
Click to collapse
Good point, and though I personally haven't done the procedure on this phone, I cannot see how more than a few basic tools plus heat gun shouldn't fix it if you're nimble enough.
Sent from my GT-N7100 using Tapatalk 2
Mine dropped from two feet and hairline cracked across the whole screen. I bought the full assembly LCD/digitizer. Did the repair per LE55ONS. AOK now. afterwards, I tried to pry apart the digitizer glass. In my Note II it is bonded with transparent gum covering the entire LCD. No way to replace only the digitizer on my version of the Note II
Hi all
I have a cracked screen on my Galaxy Nexus and want to replace it.
I know the digitizer is stuck to the glass but I've watched a video on YouTube and with a bit of time and patience it should come apart.
Has anyone successfully replace the glass and only the glass on the Galaxy Nexus?
I've seen some replacement glass on eBay for around $20 which doesn't seem too bad. But I want to know when you remove the old glass which would remove the glue holding the old glass on, do I need any glue to stick the new glass on and where would I find this so called glue?
I bought a used broken galaxy nexus off ebay that also has this issue and I am probably gonna try and fix it eventually. I ordered replacement glass off ebay for 15 dollars and its coming with little tools for the job aswell.
Did it come with stuff to stick the glass back on :s
I will probably pick it up on Monday so I can check then.
Sent from my Galaxy Nexus using xda app-developers app
I did the same thing. Found a nexus on ebay for 40 bucks with a cracked screen. Phone works perfect, I ordered replacement glass only and and I'm just way nervous to do it.
Sent from my Galaxy Nexus using xda premium
Any luck with this repair? It seems like there are people who say it can't be done and some who say it can. I've watched some videos on this topic as well but they never really show how to put the glass back on without getting air and dust trapped in between the digitizer and the glass.
chipzdelux said:
Any luck with this repair? It seems like there are people who say it can't be done and some who say it can. I've watched some videos on this topic as well but they never really show how to put the glass back on without getting air and dust trapped in between the digitizer and the glass.
Click to expand...
Click to collapse
I had the same issue with my Gnex, but after talking to private service guy,I replaced complete digitiser together with glass. The reason was simple.
As I get info from that guy, you will never be able to protect any dust to stay at digitiser area, so after some time phone will not recognise some touches,because of glue has to be used and it is not easy to cover complete area,that is why probably dust will come inside.
Anyway,those are informations I get from guy who is servicing/repairing all kinds of mobile phones, so this was his opinion and maybe there is better way,how to solve it.
I wish you good luck
It didn't come with glue .
I found this http://www.amazon.com/gp/product/B004WIQW3U/ref=oh_details_o00_s00_i00 which seems like the right thing to me.
Sent from my Galaxy Nexus using xda app-developers app
so did anyone successfully replaced the glass?
I found good deal in Amazon and not sure if this is going to work!
I have a broken GNex which I am willing to sell for parts... Anyone interested Pm me
sdhanush1 said:
I have a broken GNex which I am willing to sell for parts... Anyone interested Pm me
Click to expand...
Click to collapse
do you have an intact glass?
the.lirius said:
do you have an intact glass?
Click to expand...
Click to collapse
I had... Sold it already... I remember seeing one in eBay UK website you may want to try there.
Sent from my awesome Xperia Z
sdhanush1 said:
I had... Sold it already... I remember seeing one in eBay UK website you may want to try there.
Sent from my awesome Xperia Z
Click to expand...
Click to collapse
ty mate.. i will seriously think about it :good:
Any word on replacing the glass? I've been watching some videos about the process that includes everything except the regluing.
I found one video on the regluing process, but it shows the replacement in an industrial factory setting with an industrial autoclave vacuum to remove any air bubbles present.
I have also seen people on the YouTubes use 3mm wide double sided tape around the entire perimeter of the phone to reduce dust, but I can see potential issues with this method, as the factory method seems to apply a solid layer of adhesive material.
I would like to hear success stories, but I'm inclined to pop this thing open and give out a shot.
Sent from my Galaxy Nexus using Tapatalk 2
advise
sdhanush1 said:
I have a broken GNex which I am willing to sell for parts... Anyone interested Pm me
Click to expand...
Click to collapse
I thought the glue is not a must have parts,but samsung wont put the glue on without any reason. what i know about the glue is it will make ur glass much harder...
as many of you may know the glass on the galaxy s3 l710 not sure about the other models is not drop proof I think its just a scratch resistance glass not drop resistance glass I've seen many of post and youtube videos where folks have dropped there phone including me. and get crazy quotes to replace it. so I went digging for other options. first a little over view on the hardware of the phone there is the glass, touch screen digitizer,middle chassis, components that sit on the back of the middle chassis including mother board etc. and then the back cover.
the below youtube video shows how to take phone apart, its not hard just make sure u have the right tools. (very fine phillips head screw drivers etc)
https://www.youtube.com/watch?v=lHELvmoX0NY
this video explains why its wiser to go with the replacement touch screen digitizer assembly replacement vs glass replacement if done wrong you can brake the digitizer so best bet go with the digitizer assembly replacement.
https://www.youtube.com/watch?v=bkQZHU-SRC8
now here is what I call the exciting part, I have been hearing crazy prices for the touch screen digitizer between 300 and 500 dollars which is funny to me because the phone does not cost that much so the link below is to a website that sells parts for the phone at a very low prices.
http://www.aliexpress.com/wholesale/...30&groupsort=1
I see as low as 112 bucks. I ordered from the alieexpress before some of them ship the tools you need to disassemble the phone. I well be ordering my touch screen digitizer screen for the l710 in a week or two I'll keep you posted on the switch out. I cant wait to get it done I know a couple of phone part venders in the mall who swear you need to go the route with the heat gone etc and they can do it for me for 300 dollars yea right lol
Do you know of a place to get parts for the E4GT? I have a perfectly functional E4GT but it has a broken digitizer. The outer glass itself doesn't even have a scratch
CNexus said:
Do you know of a place to get parts for the E4GT? I have a perfectly functional E4GT but it has a broken digitizer. The outer glass itself doesn't even have a scratch
Click to expand...
Click to collapse
They actually have all parts check them out
arcolino1 said:
They actually have all parts check them out
Click to expand...
Click to collapse
Awesome, thanks
EDIT: Also just a heads up, you linked the website wrong, it leads to a 404 on their site
Try repairsuniverse.com/
Sent from my SPH-L710 using XDA Premium 4 mobile app
gronimo21 said:
Try repairsuniverse.com/
Sent from my SPH-L710 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
aliexpress.com
has way better prices, lowest I saw on the repairsuniverse.com for the s3 touch screen digitizer was 169.00
but your post made me do a random google search for samsung galaxy s3 touch screen digitizer and I
am seeing even lower prices on other websites. and the sellers have good ratings. Interesting.
That site is also from Hong Kong and it goes by alibaba.com I've order from here before everything came as is yes it's a bit higher but it's oem
Sent from my SPH-L710 using XDA Premium 4 mobile app