Related
I picked up a white one of these:
http://www.ebay.com.au/itm/For-LG-G.../221311296509?ssPageName=ADME:L:eek:C:AU:3160
It has a matte translucent finish, and the case is hard, not TPU. I prefer translucent to clear as it doesn't show all the dust and crap that inevitably builds between the phone and the case. It fits perfectly and the buttons are easily accessible. I like that you can still see the rear logo and the case isn't physically obtrusive at all. The gap between screen and front bezel is just over 1mm. Worth the buy, especially for $5. I dropped it 20 minutes ago on a tile floor from about 1m up, no physical change. Can't tell if it landed on a front or back corner as there are no marks. Paid for itself 100 times over.
Photos here:
http://imgur.com/a/pMFZI
I have had one of these for a bit over a week and it's cracking all over the place where I tend to hold my phone. Not from drops, just the stress of holding the phone. :-/
thejonesyboy said:
I picked up a white one of these:
http://www.ebay.com.au/itm/For-LG-G.../221311296509?ssPageName=ADME:L:eek:C:AU:3160
It has a matte translucent finish, and the case is hard, not TPU. I prefer translucent to clear as it doesn't show all the dust and crap that inevitably builds between the phone and the case. It fits perfectly and the buttons are easily accessible. I like that you can still see the rear logo and the case isn't physically obtrusive at all. The gap between screen and front bezel is just over 1mm. Worth the buy, especially for $5. I dropped it 20 minutes ago on a tile floor from about 1m up, no physical change. Can't tell if it landed on a front or back corner as there are no marks. Paid for itself 100 times over.
Photos here:
http://imgur.com/a/pMFZI
Click to expand...
Click to collapse
I ordered a quicksand case from the same seller so it's good to know you got your case. How long did the shipping take I wonder?
Jaxidian said:
I have had one of these for a bit over a week and it's cracking all over the place where I tend to hold my phone. Not from drops, just the stress of holding the phone. :-/
Click to expand...
Click to collapse
Mine's flexible enough not to crack, even if I try to flex it, even at the corners. It fits nicely and isn't stretching to hold the phone at all. You might have a different model?
bblzd said:
I ordered a quicksand case from the same seller so it's good to know you got your case. How long did the shipping take I wonder?
Click to expand...
Click to collapse
About two weeks to Australia.
belt clip case for N5
I have also ordered one Amzer belt clip case for my N5 from a reseller site Fommy...just waitng for it to be delivered..and will surely put up the pics and reviews of the case....as I have also used the cases earlier also of this brand and they were quite sturdy and sustainable one...so considering the past experience I ordered one for my N5 too....so hoping that it wont let me go down.....
I have a similar case only in solid white. Not even a week of use and it is showing signs of coloration..
pic : http://imgur.com/jDgNmCM
stickyness
does this case stick in your pocket?
I find that really annoying with manny cases :-/
thejonesyboy said:
I picked up a white one of these:
http://www.ebay.com.au/itm/For-LG-G.../221311296509?ssPageName=ADME:L:eek:C:AU:3160
It has a matte translucent finish, and the case is hard, not TPU. I prefer translucent to clear as it doesn't show all the dust and crap that inevitably builds between the phone and the case. It fits perfectly and the buttons are easily accessible. I like that you can still see the rear logo and the case isn't physically obtrusive at all. The gap between screen and front bezel is just over 1mm. Worth the buy, especially for $5. I dropped it 20 minutes ago on a tile floor from about 1m up, no physical change. Can't tell if it landed on a front or back corner as there are no marks. Paid for itself 100 times over.
Photos here:
http://imgur.com/a/pMFZI
Click to expand...
Click to collapse
Hey did you use the screen protector that came along with it?
Thanks for the detailed pictures. I ordered the white one, too, based on the excellent details you provided here.
Cheers
Thanks for the review. There are also some very similar cases made by Bear Motion on Amazon, might even be same case? idk here for matte smooth and here for sand
Are there any case haterz on this forum, who run their phones without any kind of cases / back stickers etc ?
Could you post some photos, facts, knowledge how well the phone stands everyday usage ?
I have been using case since day one, but i just can't stand it anymore. Did I buy alluminium phone to put it in rubber case or stick plastic sheet of foil on it to lose the feeling of alluminium ? No !
I drop my phone very rarely, actually i have never droppped it (knock knock), only time it hit ground it was clumsy bird's (jokin clumsy friend's hands) fault. My only concern is lens protector. On one side its nicely hidden in the rim, but at the other lens cover is protruding just a very litle bit. I am attaching picture to illustrate it a bit. It is side look.
There's a "hole" in the phone body, so the lens should be all hidden / drown and there should be 1 milimeter gap, when i place phone on table. On one side there is, on other lens is in line with body.
Grey - phone
White - gap for lens cover
Black - lens cover
Mods, please do not delete this topic - this has already happened in past (moved to accesories thread), but it get lost very easily, i try to debate with users without accesories.
Thanks
i did for apprx 4 months when i first bought the device, now i'm using crystal clear case to not to hide devices body.
i bought a case after i saw scratches on camera lens, luckly camera lens got replaced after service for red tint.
also shiny exposed alumium around the device got scratched and deformed a bit.
I also am not a fan of big bulky cases. One of the main reasons I bought this phone is because it is so damn beautiful (compared to most other phones). I've always joked about how iPhone fans typically rave about how "sleek" and "thin" their phones are, yet they walk around with them wearing the equivalent of a down-filled parka that is anything but "sleek".
I did compromise a bit, just because I want to keep my phone looking nice. I found the Cimo clear case. It is very thin, and very clear. It has just enough of a "lip" around the edge so that the screen of the phone won't contact the ground when it is lying down (or dropped on its face). The soft rubbery cushioning should also protect against dings on the corners and back, as well as prevent scratches. All without sacrificing the beauty of the phone. I paid $10 on Amazon for it.
NEH,
I did not buy a unibody aluminium finish phone to hide it behind chinese plastic covers. Thats not my style. I have pretty much the same type of use like yours. The only thing that has happened with me is that the beats audio red sticker at the behind bottom plate is now fading off. Nothing else. Just keep keys/card holder and coins in other pocket. I dont think you need a plastic cover.
When I had my One I used the HTC hard shell - minimal design but clear so you could still see the phone. Best case I had IMO
http://shop.emea.htc.com/uk/p_htc_store_product.aspx?i=251537
Whether you can still get it is another question
I've been using this case works well still shows the phones great looks and protect it all around.
HTC One
Guys, thanks for all the replies.
But this thread is strictly about naked devices - no cases at all !
well ii put a case on it.... next time its still usable years down the road
Mine has had nothing on it except a transparent skin on the back since i bought it last May. Still looks great...
Yeah I've been running mines nekkid since I got it last April, just couldn't bring myself to spend money to cover such a good looking device. Other than some wear marks around the shiny beveled edge, there's no obvious signs of age.
I'm not rough on it, but I don't baby it either. I have dropped it a few times(on purpose, just to show people how durable it is), and run my knife across the screen and back, but no damage.
Sent from space...
jaqual said:
Yeah I've been running mines nekkid since I got it last April, just couldn't bring myself to spend money to cover such a good looking device. Other than some wear marks around the shiny beveled edge, there's no obvious signs of age.
I'm not rough on it, but I don't baby it either. I have dropped it a few times(on purpose, just to show people how durable it is), and run my knife across the screen and back, but no damage.
Sent from space...
Click to expand...
Click to collapse
And what about lens cover ? Is yout lens completely hidden, or do you have it like me ? Hidden on one side, flush with body on the other.
Do you use any kind of pouch or something ?
never ever use a case defeats point of having such a wonderful design,have a leather pouch when not in us and just treat it like a baby when in use 6 months on still pristine not a mark
Sent from my Transformer TF101 using XDA Premium 4 mobile app
remusator said:
And what about lens cover ? Is yout lens completely hidden, or do you have it like me ? Hidden on one side, flush with body on the other.
Do you use any kind of pouch or something ?
Click to expand...
Click to collapse
My lens cover is slightly recessed, so no, not like you, but haven't had any damage to it. No pouch or anything, just keep it in my pocket with my change.
Sent from space...
No case.
I am careful when I lay it down on certain surfaces.
And I try *very* hard never to let it slip out of my hands and fall.
No damage due to general wear. I dented the back slightly and roughed up one corner slightly.
Totally worth it. Love the feel and thinness of the phone.
[1] said:
Mine has had nothing on it except a transparent skin on the back since i bought it last May. Still looks great...
Click to expand...
Click to collapse
this is how i use mine. transparent cover over the back which i only put on because the aluminum is actually very slippery for me and the clear skin provides better grip so i dont drop it. clear cover over the screen and im good to go. few small areas around the front bevel where the blue has worn away but other than that its prefect. i never use a case, defeats the purpose of having a thin phone.
I Have been using it without cover, but in December it has fallen on the road so i ordered some cheap one from the e-bay.
So now, i am using it with cover, but i lost that great metal feeling of the phone.
Here is an example with and without cover
http://i.cubeupload.com/KydqLb.jpg
I don't use a case at all makes it easier to use the volume and power button
Sent from my Verizon HTC One using Tapatalk
I use no covers, just matte screen protector (I like the way my display looks with it). Bought it in June 2013. It fell on the floor several times, it got only one scratch on the top (on the lright corner), but it still looks amazing! As it's always in my pocket, lately the "beats audio" logo on the back is going away slowly... but i use nothing to protect it
NxNW said:
No case.
I am careful when I lay it down on certain surfaces.
And I try *very* hard never to let it slip out of my hands and fall.
No damage due to general wear. I dented the back slightly and roughed up one corner slightly.
Totally worth it. Love the feel and thinness of the phone.
Click to expand...
Click to collapse
+1. Dont know how long I would keep the phone. But while I have it might as well enjoy the quality feel of it.
My HTC One is about two weeks old. I love it so much, I can't bring myself to cover this baby up.
Also, I am paying for a warranty, so if anything happens to it I'll get a new one, or maybe the M8 if they run out =D
Hi
I bought a oneplus one about 3 months ago and I absolutely love it however I dropped it a while ago and everything is fine but the frame area to the left of the charging port is completely jacked up :/ chunks of it are missing too...
I'm currently using the oneplus flip cover however it doesn't cover it up, so my question is: is there any light tpu/hard shell case that covers up the entire silver bezel, or at least the bottom of the phone so I don't have to look at this anymore xD. All cases I've seen so far leave a bit of the bottom frame exposed just enough so you can see the damage :'(
Anyone know any case that can cover it up?
Thanks!
I advise you to look for the "Diztronic" TPU case, covers completely the silver frame, following the contour of the screen. There's just a 1 cm spot where the frame is visible, at the bottom of the cover, near the hole for the USB cable, but in normal use is not visible. It's 6 months that I'm using this cover in combination with a tempered glass and I'm really satisfied.
Guess it all depends on what kind of protection you want. If you just want mild protection and to just cover the sides, then go with the tpu case. If you want heavy protection, I would suggest the Tudia Omnix Hybrid, http://www.amazon.com/TUDIA-Full-body-Protective-Protector-Resistant/dp/B00SO4XYHA . I have the Tudia case and it has taken a beating and protected the phone very well, even from some pretty high falls. Only con about the Tudia case, is that the front covers the sides of the screen a bit and prevents touch at the the very edges of screen. This can be a bit bothersome if using apps in full screen/landscape when you have to swipe down to exit full screen.
noahvt said:
Hi
Anyone know any case that can cover it up?
Thanks!
Click to expand...
Click to collapse
kenboyles72 said:
I would suggest the Tudia Omnix Hybrid
Click to expand...
Click to collapse
I too have a Tudia--Slim-fit Cygen.
thanks
thanks
Bino92 said:
I advise you to look for the "Diztronic" TPU case, covers completely the silver frame, following the contour of the screen. There's just a 1 cm spot where the frame is visible, at the bottom of the cover, near the hole for the USB cable, but in normal use is not visible. It's 6 months that I'm using this cover in combination with a tempered glass and I'm really satisfied.
Click to expand...
Click to collapse
I totally agree, couldn't have said it better. Here are some visuals for you. I got the Diztronic case when I bought the phone, it has protected it from falling out a car, off the desk, and off a moderately high shelf. You can get a tempered glass screen protector off eBay, have to search a bit (TechArmor don't have one). I got one from user dreamlight2004 for around 5 dollars. I made the mistake of getting the OPO screen protector when i first got my phone and it went bad a month ago, a hard scratch from a key. Tempered glass protector looks so much better. Just loaded COS13, it should keep me busy until the OP3 gets announced - so far it's looking to be a really good phone (boo on the OP2 and OPX)
Case view
Phone view
I agree, Diztronic bumpers are terrific.
I'm using this one http://www.ebay.com/itm/Rearth-Case-OnePlus-One-Folie-Ringke-Fusion-Schutzhulle-Cover-Tasche-klar-/121715293296?hash=item1c56cbfc70:g:gAUAAOSwT6pVt5tV And it is awesome. You can also print your designs for this case!
Ringke Fusion for me is great. It covers the OPO completly.
DO NOT BUY THE TUDIA CASE.
I bought it because I thought it looked pretty sweet. It's the worst case I have ever owned, and I have owned a few. Half the case is slippery nonsense plastic. You grab your phone "wrong" (by this I do not mean insecurely, but simply you happen to not have your fingers on enough of the case's rubber outline), it's like holding an eel.
The clips covering the audio jack and usb port are an absolute NIGHTMARE to open, and plugging in your charger for the night would realistically take three hands with 17 fingers each to manage in a reasonable timeframe. Good thing my audio jack's clip, after having been used exactly twice without even the slightest bit of the abuse it deserved, now no longer clips into it's crevice, and is permanently hanging out at a 30 degree angle. The pop-out clip on the back is nail ruining torture to get out, as is the rubber outline holding the front of the case, should you want to get this garbage off to see how far you can launch it through the air in rage.
I wouldn't use this piece of junk if they paid me.
I am using the TUDIA Dual-Layer case+a glass screen protector, which turned my One to a tank
I drop it way too often, but it still works flawlessly, so I can recommend this case. It also coverers the aluminum frame
I can rep the Poetic Case found here:
I took out the screen protector but I have been rocking the case for more than a year. It is kinda bulky but I have no worries about dropping it or tossing my phone on my desk. Also, It is kinda water resistant (with the screen protector). I have dropped like a glass of water on it and quickly cleaned it up with no harm
Considering the new xperia x has one and that the back cover on the z3 is easily replaced, wouldn't it be a great idea to give your old phone an updated look by just putting a custom back on it!
Can be done. The camera plastic cover is glued to the back cover from the inside?
isn't it like a Faraday cage? does it kill the wifi + mobile signals?
bookworth said:
isn't it like a Faraday cage? does it kill the wifi + mobile signals?
Click to expand...
Click to collapse
Shouldn't kill them (maybe it will be tricky with NFC). The thing is that the frame around the phone is plastic, so that should be enough for the WiFi.
Guids said:
Considering the new xperia x has one and that the back cover on the z3 is easily replaced, wouldn't it be a great idea to give your old phone an updated look by just putting a custom back on it!
Click to expand...
Click to collapse
THat's a good idea. I thought about it and was wondering about the Faraday effect. But then again I would settle with anything that is not glass to be honest.
I'm sure that anybody with a CNC could make a custom backplate in POM or any other resistant plastic...
Now to find somebody on the forum with a CNC and spare time!
I made my own in acryllic plastic.
1. Cut out in 1mm acryllic sheet using the old back as a template and then cut with Exactoknife(Needs to cut/draw a line several times with exactoknife, acryllic is tough to cut, also needs to be sanded down to same size as old cover. Sanded evenly and not to fast to prevent friction heat that messes up the acryllic)
2. Take out camera lens from the old frame (Adhesive tape, easy to remove with exacto)
3. Drill a hole for camera lens using old back as template.
4. Sanded both sides from 80 to 120(Wood) then 400>600>800>1200 Silicone carbide paper(Wet)
5. Heated it up evenly with a flame on both sides to give it a darker smoked color then stuck it between two flat objects to prevent it bubbling or deforming until it cooled down.
(Heated back and forth so it didnt get too hot and had time to cool)
6. Once cool, washed with water.
7. A few smooth strokes against 1200 Silicone Carbide (Wet) to even out any irragularities
8. Dried, then a few smooth strokes with 1200 Silicone Carbide dry, sideways to have an even pattern and smooth surface.
9. Took the camera lens, glued into hole. Let dry then 1200dry sanded around camera hole to remove glue residue. (Dont sand the camera lens or you have to polish it. Major PITA..)
10. Took the top part of the black sticker from the inside of the old glass cover, cut out the top camera part as a square and stuck it around camera and flash to prevent flash bleeds.
11. Reapply new adhesive tape to the cover and reapply it and voila, waterproof again
This is my 3rd, made it last night, rushed job as I was tired wanting to sleep, so did not care about looks.
Also couldn't find one of my previous glass covers so I had to reuse the camera lens and sticker from the old plastic cover.
Resulting in the camera lens outer ring breaking off and the sticker being semi sticky and filled with bubbles. But it functions, which was the main idea.
Didnt bother about sanding it decently so there's still scratches, but it gives you an picture what it looks like.
If done properly and more patiently you can get a smoother texture, no air bubbles and a non broken lens, but once superglued that lens is stuck rocksolid.
Hey guys, is there a drawing of the back cover available?
I would like to try a 3D-print, after the second back cover is broken.
But I don't have a radius gauge and need the radius of the corners.
Thanks for your help.
@mike the pike
what a coincidence!
I have made a modell in FreeCad because I had the same idea like you. But I don't have a 3D printer, so my plan was to order it from a german company which offers to cut parts out of plastic plates.
I'am not a drawing or CAD profi, in fact this was my first experience with stuff like this, but I am pretty shure my modell is quite accurate. My only opportunity to test it, was to print a 1:1 sketch and compare it with the (broken) original backcover.
Feel free to use and modify my work, but please tell me if it works. :highfive:
Doing this, part one
I spent some time in the machine shop on campus yesterday, and, with the help of the assistants, made a metal back out of sheet aluminum.
The toughness is far superior to glass, and the strength is, too (the glass used on the Z3 Compact by default is somewhat pathetic).
From here, I was planning to first apply a brushed finish with an abrasive pad and WD-40 (thanks, YouTube) then either anodize (time to steal a HVPS from a hardware store?) black, or pay someone to apply a thermoset powder coat. Anodizing would probably yield better results, and be cheaper, but the scratch resistance on the aluminum is a bit low, so thermoset would help a bit. Oh, and the bottom left corner is a little bit off. Might get some silicone caulk and apply at the corner for waterproofing. Otherwise, it turned out extremely well. Filed down the corners myself to get the perfect fit.
One problem that I have is the flash. The normal back glass is a plane of glass stretching across the LED in the back. Will either 3D print it, or, more realistically, just stick a spare Z3 Compact camera lens cover on it and call it a day. Any other suggestions are welcome.
Also, I'm not allowed to post images, since I made this account for this . If you're interested in the result, PM me.
Eric
P.S.: NFC doesn't work but reception is perfect.
Barrel_Trollz said:
I spent some time in the machine shop on campus yesterday, and, with the help of the assistants, made a metal back out of sheet aluminum.
The toughness is far superior to glass, and the strength is, too (the glass used on the Z3 Compact by default is somewhat pathetic).
From here, I was planning to first apply a brushed finish with an abrasive pad and WD-40 (thanks, YouTube) then either anodize (time to steal a HVPS from a hardware store?) black, or pay someone to apply a thermoset powder coat. Anodizing would probably yield better results, and be cheaper, but the scratch resistance on the aluminum is a bit low, so thermoset would help a bit. Oh, and the bottom left corner is a little bit off. Might get some silicone caulk and apply at the corner for waterproofing. Otherwise, it turned out extremely well. Filed down the corners myself to get the perfect fit.
One problem that I have is the flash. The normal back glass is a plane of glass stretching across the LED in the back. Will either 3D print it, or, more realistically, just stick a spare Z3 Compact camera lens cover on it and call it a day. Any other suggestions are welcome.
Also, I'm not allowed to post images, since I made this account for this . If you're interested in the result, PM me.
Eric
P.S.: NFC doesn't work but reception is perfect.
Click to expand...
Click to collapse
I assume that the glass they use for the camera lens is of a convex design such to scatter the light intensity for maximum coverage of the subject. It won't be so easy as just using any untreated material unless you want a dull-flash. Assuming you've already made your cuts to good tolerances, then why not just source your adhesives from the OEM itself? Save yourself some work. The proper way to apply those adhesives(as such to retain the water-resistant nature) is to use a hot plate up to 100 C and place it on the plate for a few seconds before pulling it off.
I'm mainly worried about the cut at the bottom left. It's not at all made to a good tolerance. I did buy the adhesive sticker, and I plan to use it, but some silicone wouldn't hurt on that one place.
Also, there is a bit of distortion when I look through it, so you're right. Not much I can do about it, though, but pray to the gods of diffraction.
allerd said:
@mike the pike
what a coincidence!
I have made a modell in FreeCad because I had the same idea like you. But I don't have a 3D printer, so my plan was to order it from a german company which offers to cut parts out of plastic plates.
I'am not a drawing or CAD profi, in fact this was my first experience with stuff like this, but I am pretty shure my modell is quite accurate. My only opportunity to test it, was to print a 1:1 sketch and compare it with the (broken) original backcover.
Feel free to use and modify my work, but please tell me if it works. :highfive:
Click to expand...
Click to collapse
Sorry, I didn't visit this site quiet a wile.
I lent me a radius-gauge and I think I found some good values.
Unfortunately I don't have them in mind, because I gave them to a colleague, how will 3D-print the cover for me.
As I only made hand-drawing, he will transcript it into any 3D-data-file, which I will provide you here, as soon as I received the results.
So stay tuned.
The cover for the camera is still usable and I plan to insert it into the new back-cover, but I'm quite at a loss about the flashlight.
p.s. Yesterday I mounted my 4th back-cover
Accurate 3D model and curves for creating z3c back cover:
http://www.thingiverse.com/thing:1998130
Mission complete
Hi all!
I finished my metal back cover. Still a new user, so can't post images, but I just wanted to let you guys know that I completed it and the phone is 100% functional (aside from NFC, RIP).
In the end, I anodized the aluminum and used a thin plastic sheet sealed with superglue around the flash (flash works fine BTW), and gave it a little brushed finish afterwards that cut into the anodized piece ever so slightly.
I'm very happy with it, the finish on this phone is unlike any I've ever felt. Smooth, yet solid, soft, yet sturdy. The phone is cool to the touch when in standby. The camera was a bit wonky at first, but as I pressed down into the metal back it stabilized, and now seems very resilient. The anodization itself didn't go all that smoothly (took four tries), with the metal part itself ending up with an uneven finish. It being black and brushed helps, as the texture undulates, making up for the inconsistencies.
I made a post to /r/Android with images and more details. Same username as on here. Go check it out if you're interested.
Eric
Mission also complete
I finished now my 3D-printed backcover and it is quite satisfying.
I made it by using the file railpl posted.
Unfortunately it is about half a mm to short so there is a small gap on the short side, but for me it is okay.
I used the lenscover from my old glassback and drilled a tiny hole for the flashlite.
So I think it is not waterproof anymore.
Hi all,
I purchased one of these, a red one, a few days ago for my Le Max 2, and thought some of you might like it.
It fits great, although I did have to shave a millimeter off of the USB-C area so that the CDLA jack would slide in properly.
I'm posting a store link to it here. However, I'm not the seller nor am I an affiliate. So I'm not getting paid to promote it.
Kind regards,
Bill...
New 360 Protection Housing For LeEco Le Max 2 Case Ultra-thin Hard matte PC Back Cover Phone Case for Letv Le 2 Max X820 5.7"
http://s.aliexpress.com/iuEVRrYJ
(from AliExpress Android)
I bought the black "textured" of the same case, works great. Super slim, slight edge so screen doesn't touch on face down, lip around camera lens , cheap.
Its really the perfect case.
Supertacomonkeyexplosion said:
I bought the black "textured" of the same case, works great. Super slim, slight edge so screen doesn't touch on face down, lip around camera lens , cheap.
Its really the perfect case.
Click to expand...
Click to collapse
Yeah, I quite like it also. And the price is very reasonable... :good:
Yes, this is one of the best cases for this phone. I had one for about 8-9 months. I used the gold one, it matches somehow with the rose gold color of the phone so it won't look that girlish with the case. The rubber starts to peel off slightly at the edges after about 4-5 months, depending on usage (I always slide it in my jeans pocket). After about 6 months some cracks start to appear at the corners where the case is cut. It performs very well though. Because I was happy with it, I ordered 2 more of the same, but I found them a bit cheaper.
Now I'm using a skin which looks like this: Wire Drawing membrane Skins Protective Film Wrap Skin Cellphone full body Protective Sticker For LeEco Letv Le 2 2Pro/Le Max 2
http://s.aliexpress.com/vyIrQFrm
(from AliExpress Android)
The parts that stick on the screen are useless because I use a tempered glass and they come over the edges. On top of this I have the original transparent case from LeEco to protect the skin. I'm not sure how long would the glue last on the sides without the case. The chamfered edges remain uncovered though.
valy_cta said:
Yes, this is one of the best cases for this phone. I had one for about 8-9 months. I used the gold one, it matches somehow with the rose gold color of the phone so it won't look that girlish with the case. The rubber starts to peel off slightly at the edges after about 4-5 months, depending on usage (I always slide it in my jeans pocket). After about 6 months some cracks start to appear at the corners where the case is cut. It performs very well though.
Click to expand...
Click to collapse
I anticipate that it will wear a bit eventually. However, for the price, I'm very satisfied with it...