puting a reward for anyone that can solve my prob - T-Mobile Samsung Galaxy S II SGH-T989

hey guys i have a problem with my ssgs2 t mobile and i have a phone that wont turn on but it well be seen by Odin but no download mode i flashed a kernel on my internal SD and it ****ed up my phone and i am offering 50 dollars usd for anyone that can fix it by software via Odin or any other software that can unbrick my phone

1. Pulling and replacing battery then holding vol up and down then plugging in usb does nothing?
2. can you just flash a stock rom from odin? http://forum.xda-developers.com/showthread.php?t=1350360

don728871 said:
hey guys i have a problem with my ssgs2 t mobile and i have a phone that wont turn on but it well be seen by Odin but no download mode i flashed a kernel on my internal SD and it ****ed up my phone and i am offering 50 dollars usd for anyone that can fix it by software via Odin or any other software that can unbrick my phone
Click to expand...
Click to collapse
If Odin sees it, can you flash a stock recovery?

Do the OLED buttons light up at all??
If the buttons light up, it could be your phone is powering on but the display has died, would not be the first one I have seen ...
If Odin is seeing it, and flashing stock gets you no where, I am willing to bet that it is a hardware issue that software is not going to be able to fix ...

I would use this method to restore it back to original stock and then go from there. There is a video and everything.
http://forum.xda-developers.com/showthread.php?t=1393938

This is what I did when I had that problem;
1. Plug phone into computer and open Odin
2. If Odin detects it, move on
3. Click PDA and select the stock 2.3.6
4. Click "START"
5. Wait
6. If it doesn't work unplug and repeat.
*I did this process 3 times before my phone finally booted up

it might work
i well go to the odin and get stock rom 2.3.6 but do i need a pit file and if so where can i get one

can i have a boot loader for my t989 and if i flashed a bad kernel what do i need to recover

don728871 said:
i well go to the odin and get stock rom 2.3.6 but do i need a pit file and if so where can i get one
Click to expand...
Click to collapse
No pit file needed just flash the md5 file found here http://forum.xda-developers.com/showthread.php?t=1391174 (after you unrar it) in odin to get back to stock rom and kernel along with recovery.. You will have to reapply root with odin again afterwards
Sent from my SGH-T989 using Tapatalk

i need a new bootloader for my t989

Related

Sprint Note 2 bricked

Hello everyone i got a note 2 sprint bricked. I used odin and it keeps saying failed at sboot.bin right after recovery.please help if you can thanks.
carshass said:
Hello everyone i got a note 2 sprint bricked. I used odin and it keeps saying failed at sboot.bin right after recovery.please help if you can thanks.
Click to expand...
Click to collapse
You need to post more info if possible but it sounds like you are trying to downgrade from MA7 to an earlier firmware like LK8. The update included a security patch so it won't let you go back to insecure. Try pulling the sboot out of whatever you are trying to flash or stick with MA7
Sent from my SPH-L900 using xda app-developers app
Try downloading another .tar file for ljc. I had the same issue. I believe i got a working one directly from samfirmware
Sent from my SPH-L900 using xda app-developers app
oook,, so im new to the note2 just came from a gs2 with jellybam on it...soo im running jellybomb and i flashed venum ice reborn 1.5 it seemed to fash fine until reboot,, then it just hung on the note2 bootup screen. i hold down home and power and it says up to download custom rom down to restart... both jut hang. help?
i got as far as trying to find odin but i couldnt and stopped.
shangus1 said:
oook,, so im new to the note2 just came from a gs2 with jellybam on it...soo im running jellybomb and i flashed venum ice reborn 1.5 it seemed to fash fine until reboot,, then it just hung on the note2 bootup screen. i hold down home and power and it says up to download custom rom down to restart... both jut hang. help?
i got as far as trying to find odin but i couldnt and stopped.
Click to expand...
Click to collapse
umm ya i see why i didnt get a reply.. all i had to do was hold volume up home power and the n re flash... its amazing what you can figure out inhere when ignored lolz
carshass said:
Hello everyone i got a note 2 sprint bricked. I used odin and it keeps saying failed at sboot.bin right after recovery.please help if you can thanks.
Click to expand...
Click to collapse
I've been having the same problem for a couple days now. I can install a custom rom but I can't figure out how to get back to stock.
You need to post more info if possible but it sounds like you are trying to downgrade from MA7 to an earlier firmware like LK8
Click to expand...
Click to collapse
That might be the problem I'm having.
EDIT:
Yep, that was it. Thanks!
carshass said:
Hello everyone i got a note 2 sprint bricked. I used odin and it keeps saying failed at sboot.bin right after recovery.please help if you can thanks.
Click to expand...
Click to collapse
It's not brick cuz odin can still see your phone. If you dont have TWRP on it, go to www.twrp.com and download the tar file for sprint note 2. Then use Odin to flash it. Once you are done that, go here http://forum.xda-developers.com/showthread.php?t=2086769 to get either the old LJC or MA7 and put it in your phone either internal or external SD. Do the wipe cache/factory reset first. Then flash it. It will go back to stock rom.
Help
Hello even though its old I figured I would post here first instead of starting a new thread, my friend has a Note 2 for Sprint never rooted or custom ROM flashed and he said it was sitting on the charger and when he woke up in the morning it was off and after attempting to power the device on it stays stuck on the Samsung logo. I cant get Kies to recognize the device at all not matter what pc is use however it shows up in Odin but it fails everything from stock files ( older and current ) , different versions of Odin, recoveries and I even tried a " unbrick .tar file " . Any help at all would be appreciated I will include pics
demorik said:
Hello even though its old I figured I would post here first instead of starting a new thread, my friend has a Note 2 for Sprint never rooted or custom ROM flashed and he said it was sitting on the charger and when he woke up in the morning it was off and after attempting to power the device on it stays stuck on the Samsung logo. I cant get Kies to recognize the device at all not matter what pc is use however it shows up in Odin but it fails everything from stock files ( older and current ) , different versions of Odin, recoveries and I even tried a " unbrick .tar file " . Any help at all would be appreciated I will include pics
Click to expand...
Click to collapse
Can you odin a custom recovery and boot into it?
1. Put phone in download mode
2. In odin program uncheck reboot and flash recovery
3. After flash disconnect phone and pull battery
4. Quickly insert and remove battery multiple times (if you just reinsert battery it will automatically boot)
5. Boot phone into recovery backup any important data that is on your internal sdcard
6. Do factory reset then flash billards stock mc2 with counter reset (do not wipe cache after flashing this)
7. Flash superuser zip found in billards Op
8. Reboot phone and freakout when see the screen do odd things and reboot (this is normal)
Now it will bootup on stock rooted mc2.
Sent from my SPH-L900 using XDA Premium 4 mobile app
jlmancuso said:
Can you odin a custom recovery and boot into it?
1. Put phone in download mode
2. In odin program uncheck reboot and flash recovery
3. After flash disconnect phone and pull battery
4. Quickly insert and remove battery multiple times (if you just reinsert battery it will automatically boot)
5. Boot phone into recovery backup any important data that is on your internal sdcard
6. Do factory reset then flash billards stock mc2 with counter reset (do not wipe cache after flashing this)
7. Flash superuser zip found in billards Op
8. Reboot phone and freakout when see the screen do odd things and reboot (this is normal)
Now it will bootup on stock rooted mc2.
Sent from my SPH-L900 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I have tried but I never tried to uncheck anything in Odin, I will try it later and post the results thanks.
say my brother it still doesnt let me boot into recovery what do i do...
jlmancuso said:
Can you odin a custom recovery and boot into it?
1. Put phone in download mode
2. In odin program uncheck reboot and flash recovery
3. After flash disconnect phone and pull battery
4. Quickly insert and remove battery multiple times (if you just reinsert battery it will automatically boot)
5. Boot phone into recovery backup any important data that is on your internal sdcard
6. Do factory reset then flash billards stock mc2 with counter reset (do not wipe cache after flashing this)
7. Flash superuser zip found in billards Op
8. Reboot phone and freakout when see the screen do odd things and reboot (this is normal)
Now it will bootup on stock rooted mc2.
Sent from my SPH-L900 using XDA Premium 4 mobile app
Click to expand...
Click to collapse

Has my phone bitten the dust?

Really hope somebody can help.
I have had a galaxy note 2 for about 6 months on Vodafone UK N7100.
Today while i was at work i felt something hot in my pocket, my phone was very hot (i was not doing anything with it) The phone was stuck on the Samsung boot screen.
After a few minutes of looking at this i realised it was stuck and removed the battery. SInce then i have been unable to get past the boot screen, i can't get into download mode or reboot mode. The only things to note. When i turn my phone on a red light flashes. When i plug my charger in the charge icon appears on screen but it does not charge.
Really hoping somebody can help.
I had rooted my phone if that helps (it did not cause this problem and has been functioning rooted for months)
Update
Just managed to get to a screen which warned me about installing custom software and did i want to continue. I said yes and it is now downloading something
How did you get to that screen?
Sent from my Desire S using xda app-developers app
The Mole said:
Really hope somebody can help.
I have had a galaxy note 2 for about 6 months on Vodafone UK N7100.
Today while i was at work i felt something hot in my pocket, my phone was very hot (i was not doing anything with it) The phone was stuck on the Samsung boot screen.
After a few minutes of looking at this i realised it was stuck and removed the battery. SInce then i have been unable to get past the boot screen, i can't get into download mode or reboot mode. The only things to note. When i turn my phone on a red light flashes. When i plug my charger in the charge icon appears on screen but it does not charge.
Really hoping somebody can help.
I had rooted my phone if that helps (it did not cause this problem and has been functioning rooted for months)
Update
Just managed to get to a screen which warned me about installing custom software and did i want to continue. I said yes and it is now downloading something
Click to expand...
Click to collapse
does it get recognize in odin if yes try to flash stock rom and revive your phone hopefully u are not using the 4.1.1 rom better get a 4.1.2 and bring it to life :good:
if u can get to download mode now then flashed philz recovery first. After flashing recovery wipe dalvik, cache partition & then data reset.then u can flash stock using odin. try this if the first one doesnt work
shhbz said:
does it get recognize in odin if yes try to flash stock rom and revive your phone hopefully u are not using the 4.1.1 rom better get a 4.1.2 and bring it to life :good:
if u can get to download mode now then flashed philz recovery first. After flashing recovery wipe dalvik, cache partition & then data reset.then u can flash stock using odin. try this if the first one doesnt work
Click to expand...
Click to collapse
I got there through home volume down and power during boot up.
I can't get into recovery though (using volume up)
Which version of odin should i be using? I am using 3.07
I am using the rom suggested in this guide http://reviews.cnet.co.uk/mobile-ph...e-2-from-rooted-to-factory-settings-50010623/
If i should not be using that where can i get the one i should be using.
When i try to install the stock rom linked above i get the message failed no PIT partition
Thanks for all the help so far
The Mole said:
I got there through home volume down and power during boot up.
I can't get into recovery though (using volume up)
Which version of odin should i be using? I am using 3.07
I am using the rom suggested in this guide http://reviews.cnet.co.uk/mobile-ph...e-2-from-rooted-to-factory-settings-50010623/
If i should not be using that where can i get the one i should be using.
When i try to install the stock rom linked above i get the message failed no PIT partition
Thanks for all the help so far
Click to expand...
Click to collapse
this would be your last hope http://forum.xda-developers.com/showpost.php?p=32273406&postcount=5 follow the guide properly marked in red and remember to tick re partition in odin, if this doesnt work then your phone has been affected by sds due to 4.1.1 rom so u need to take it to service for motherboard replacement which is borne by samsung so no worries, and remember never to use a 4.1.1 rom in note 2 get the 4.1.2 rom or rather they will install that only this time and in future just go through dr.ketan thread http://forum.xda-developers.com/showthread.php?t=1896696 here it will guide you perfect instead following some untidy guides
for odin use 3.04 it works great though i havent tried new version as 3.04 works great you will get it in ketan thread
shhbz said:
this would be your last hope http://forum.xda-developers.com/showpost.php?p=32273406&postcount=5 follow the guide properly marked in red and remember to tick re partition in odin, if this doesnt work then your phone has been affected by sds due to 4.1.1 rom so u need to take it to service for motherboard replacement which is borne by samsung so no worries, and remember never to use a 4.1.1 rom in note 2 get the 4.1.2 rom or rather they will install that only this time and in future just go through dr.ketan thread http://forum.xda-developers.com/showthread.php?t=1896696 here it will guide you perfect instead following some untidy guides
for odin use 3.04 it works great though i havent tried new version as 3.04 works great you will get it in ketan thread
Click to expand...
Click to collapse
Thanks for the advice i am downloading the file now.
I did not manage to install the rom i suggested i was using so i don't think that could have been the issue. My phone just seemed to get hot then stop working, i hope as you suggested it is not my motherboard. Did you say that i should still be covered by the warrenty even though i had rooted my device?
The Mole said:
Thanks for the advice i am downloading the file now.
I did not manage to install the rom i suggested i was using so i don't think that could have been the issue. My phone just seemed to get hot then stop working, i hope as you suggested it is not my motherboard. Did you say that i should still be covered by the warrenty even though i had rooted my device?
Click to expand...
Click to collapse
well your reply is quite confusing
1.did you manage to flash the rom with pit in odin. was it successful or you get any errors
2.does your phone start now
3.if not then your phone has died and it needs to be taken to service guys ,but just check what the status of your phone in download mode is it official or custom . if its official then no worries just go ahead and take it to service guys and tell them abt your issue that the phone stopped working while in pocket dont info them that you rooted it ever just make them blv that it was a sds caused by 4.1.1 rom so they replace it free.
i mean your motherboard
Sorry if i am confusing matters.
I did not manage to flash anything it was just coming up with failed no PIT partition.
Current binary samsung official
My system status is custom
Are these ok to return my phone with?
I decided to take the advice offered and download the recovery but got confused.
Do i need all of the files from that link or just 1?
I downloaded the first one N7100XXDMB2_Factory
It contained
boot
cache
hidden
modem.bin
recovery
sboot.bin
system
tz
None of these are the md5 format
i am now thinking i should have downloaded XXDLJ2_OXA_Factory
Is that correct or was i right with the first file. If i was right downloading the first file then where do i get the md5 files required for odin to do my factory restore.
Know these are very noobish questions just doint want to do anything wrong
In answers to your questions....
1) Did i manage to flash the rom with it in odin
No
I got confused which files i should be using and did not want to do anything without being sure
2) My phone does not start
3) When i am in download mode my phone shows
Current binary Samsung official
My system status is custom
Are these ok to return my phone with?
The Mole said:
Sorry if i am confusing matters.
I did not manage to flash anything it was just coming up with failed no PIT partition.
Current binary samsung official
My system status is custom
Are these ok to return my phone with?
I decided to take the advice offered and download the recovery but got confused.
Do i need all of the files from that link or just 1?
I downloaded the first one N7100XXDMB2_Factory
It contained
boot
cache
hidden
modem.bin
recovery
sboot.bin
system
tz
None of these are the md5 format
i am now thinking i should have downloaded XXDLJ2_OXA_Factory
Is that correct or was i right with the first file. If i was right downloading the first file then where do i get the md5 files required for odin to do my factory restore.
Know these are very noobish questions just doint want to do anything wrong
Click to expand...
Click to collapse
well follow this video but just select all file required and then flash instead flashing twice hope this video helps as u need to select individual file
https://www.youtube.com/watch?v=CMSsoCqZr1w if you still face prob ask the uploader in that thread maybe he can help you and as far as system status is concerned u need to either flash a stock rom or get into recovery to wipe data and factory reset or ven this https://www.youtube.com/watch?v=PpWcM44On88 for your proper understanding. dont you get .tar file and pit file in that download
are u able to enter into recovery mode as first post u mentioned download mode not working now u say its working
shhbz said:
well follow this video but just select all file required and then flash instead flashing twice hope this video helps as u need to select individual file
https://www.youtube.com/watch?v=CMSsoCqZr1w if you still face prob ask the uploader in that thread maybe he can help you and as far as system status is concerned u need to either flash a stock rom or get into recovery to wipe data and factory reset or ven this https://www.youtube.com/watch?v=PpWcM44On88 for your proper understanding
are u able to enter into recovery mode as first post u mentioned download mode not working now u say its working
Click to expand...
Click to collapse
Sorry recovery mode is not working, only download mode, i will have a look at the suggested video.
Thanks again for your continued help
The Mole said:
Sorry recovery mode is not working, only download mode, i will have a look at the suggested video.
Thanks again for your continued help
Click to expand...
Click to collapse
well initially it was a bootloader issue but destroying the pit became an issues hopefully u get it back to life this time
shhbz said:
well initially it was a bootloader issue but destroying the pit became an issues hopefully u get it back to life this time
Click to expand...
Click to collapse
I have managed to get hold of the correct files, however when i try to run them in ODIN ODIN does not get past the stage get PIT for mapping.
Can i try anything without the PIT stage?
The Mole said:
I have managed to get hold of the correct files, however when i try to run them in ODIN ODIN does not get past the stage get PIT for mapping.
Can i try anything without the PIT stage?
Click to expand...
Click to collapse
If your phone doesn't have a partition map, then no, you can't.
You can try, as a last resort, using this guide: http://forum.xda-developers.com/showpost.php?p=43760271&postcount=22
I had a similar problem not too long ago (although it started with all apps crashing and then stuck at bootscreen) and managed to fix my phone.
Sent from my GT-N7100
vladeco said:
If your phone doesn't have a partition map, then no, you can't.
You can try, as a last resort, using this guide: http://forum.xda-developers.com/showpost.php?p=43760271&postcount=22
I had a similar problem not too long ago (although it started with all apps crashing and then stuck at bootscreen) and managed to fix my phone.
Sent from my GT-N7100
Click to expand...
Click to collapse
Sounds like the same issue i have had. Apps kept crashing, i never thought it was the phone just the apps. I will look into the link thanks very much
CAn i just ask what is an EFS and how do i get a backup of it
If you need any help I'm here. Cheers!
Sent from my GT-N7100
vladeco said:
If you need any help I'm here. Cheers!
Sent from my GT-N7100
Click to expand...
Click to collapse
Thanks can i just ask what EFS is and how i get a backup of mine before i carry out your guide.
The Mole said:
Thanks can i just ask what ENS is and how i get a backup of mine before i carry out your guide.
Click to expand...
Click to collapse
EFS is a part of the system that stores your serial number, IMEI and everything related to your phone specifically. You are generally able to back it up using a custom recovery or using software on your PC while the phone is rooted and booted on the android OS. Since you cannot boot into recovery and also can't boot into android itself, I don't think you would be able to back it up.
If you ever installed a custom rom with AROMA, there is a chance you have it backed up already. But if you don't explicitly remember...
vladeco said:
EFS is a part of the system that stores your serial number, IMEI and everything related to your phone specifically. You are generally able to back it up using a custom recovery or using software on your PC while the phone is rooted and booted on the android OS. Since you cannot boot into recovery and also can't boot into android itself, I don't think you would be able to back it up.
If you ever installed a custom rom with AROMA, there is a chance you have it backed up already. But if you don't explicitly remember...
Click to expand...
Click to collapse
Ah ok,
I will give the guide a go and let you know how i go.
Thanks again
I get the error message write operation failed in ODIN, i am guessing that means its dead.
Do you happen to know if i take it back to my phone company to fix if they will be able to tell i had rooted it
on the download screen i have
Current binary samsung official
My system status is custom
could they tell anything from that?

[Q] Firmware upgrade encountered an issue. Please help!

Noob here, please be patient.
Samsung SGH-T989D was running CM 9. Did a factory reset as I was planing to sell the phone, but once I did that the phone was stuck in a loop at the boot logo.
Tried upgrading via recovery mode to the new CM 10, but was still stuck in boot loop.
Tried clearing cache, etc...but nothing would work.
So I downloaded the newest stock Telus ROM, put the phone into download mode and used Odin to flash - however Odin failed.
Now the phone won't start and I immediately get the following message: "Firmware upgrade encounted an issue. Please select recovery mode in Kies and try again".
I tried Kies recovery mode but it does not see my phone. Odin still sees it, but wont flash it.
I found this thread for the S2 - http://forum.xda-developers.com/showthread.php?t=1457458.
But I have not been able to find one for the S2x.. Where would I find the bootloader and kernel to flash as it explains in the above guide...
Or maybe someone has other advice?
Thanks for your help!!
http://forum.xda-developers.com/showthread.php?t=2076939
Lots of stuff the t989 there. Just be sure you actually have the t989 or t989d.
Or look through our dev section for probably more up to date stuff.
Sent from my cell phone telephone
---------- Post added at 07:35 PM ---------- Previous post was at 07:34 PM ----------
Forget the other thread you found. That's not our phone and anything there that you flash could brick your phone!!
Sent from my cell phone telephone
fruzmatik said:
Noob here, please be patient.
Samsung SGH-T989D was running CM 9. Did a factory reset as I was planing to sell the phone, but once I did that the phone was stuck in a loop at the boot logo.
Tried upgrading via recovery mode to the new CM 10, but was still stuck in boot loop.
Tried clearing cache, etc...but nothing would work.
So I downloaded the newest stock Telus ROM, put the phone into download mode and used Odin to flash - however Odin failed.
Now the phone won't start and I immediately get the following message: "Firmware upgrade encounted an issue. Please select recovery mode in Kies and try again".
I tried Kies recovery mode but it does not see my phone. Odin still sees it, but wont flash it.
I found this thread for the S2 - http://forum.xda-developers.com/showthread.php?t=1457458.
But I have not been able to find one for the S2x.. Where would I find the bootloader and kernel to flash as it explains in the above guide...
Or maybe someone has other advice?
Thanks for your help!!
Click to expand...
Click to collapse
All u need to do is download Odin 1.85 to ur PC, then go to http://techerrata.com/browse/twrp2/hercules and download the twrp 2.6.6.0.tar.md5 to ur PC, power ur phone on in download mode, the same screen will come up "firmware...issue", kids will do nothing for this and u will need to make sure kids is NOT RUNNING. Odin will not see the device if kies is running at all, now open the Odin program and connect the phone to PC using OEM factory USB cable, on Odin it should say "added", now click the box PDA, find the twrp file u downloaded b4, click on that file and then hit start in Odin, DO NOT CHECK ANYTHING ELSE... Let Odin do its thing and u will be fine, Odin will reboot the phone and u will now have twrp recovery, boot to recovery to finish rooting process
Sent from my SGH-T989 using xda premium
soupysoup said:
All u need to do is download Odin 1.85 to ur PC, then go to and download the twrp 2.6.6.0.tar.md5 to ur PC, power ur phone on in download mode, the same screen will come up "firmware...issue", kids will do nothing for this and u will need to make sure kids is NOT RUNNING. Odin will not see the device if kies is running at all, now open the Odin program and connect the phone to PC using OEM factory USB cable, on Odin it should say "added", now click the box PDA, find the twrp file u downloaded b4, click on that file and then hit start in Odin, DO NOT CHECK ANYTHING ELSE... Let Odin do its thing and u will be fine, Odin will reboot the phone and u will now have twrp recovery, boot to recovery to finish rooting process
Sent from my SGH-T989 using xda premium
Click to expand...
Click to collapse
Went to the site you linked but there is no twrp 2.6.6.0.tar.md5
I downloaded openrecovcery-twrp-2.6.0.0-hercules.tar
However, in Odin it still wont flash the phone (I closed all Kies processes beforehand).
This is all that happens - just hangs here...
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
kj2112 said:
Forget the other thread you found. That's not our phone and anything there that you flash could brick your phone!!
Sent from my cell phone telephone
Click to expand...
Click to collapse
I wasnt going to use the files from the other thread, I just assumed I could try this procedure once I got the correct files for the SGH-T989D:
Recovering a soft bricked phone
1) Grab the Recovery Package, and you'll see a bunch of .tar files. Take a look at the names. You'll see CODE, MODEM, CSC and .PIT. Put each one in its place.
2) Turn off your phone. Enter Download mode by presing Volume Down + Home + Power button.
3) Plug in your phone. It will show you, in a yellow box in ODIN, ID:COMx (x being the number displayed, sometimes displays 7, sometimes displays 9)
Now here, take a breath
First try flashing WITHOUT the .PIT and re-partition. And only if it DOESN'T WORK OR FIX then you flash with the .PIT and Re-Partition ticked.
4) Once ready and done all your prayers, press Start. Wait patiently. It usually takes 5 minutes to flash.
Have you done everything correctly until now? Then...
Congratulations on recovering your phone!
You deserve some cake afterwards, and some rest
Now, if your problem is the NAND rw coruption, and wasn't fixed by the above fix, then follow these steps :
5) Download the Kernel. Flash it in PDA. Without ticking Re-Partitioning
6) Successful? Nice, hope is still present.
7) Flash the recovery package, following steps 1-4 This should fix your issue. If it does not, then :
WARNING : FLASHING A BOOTLOADER IS DANGEROUS. FLASH WITH EXTREME CAUTION.
8) Download the Bootloader. Flash it as PDA or Bootloader in ODIN. Without ticking Re-Partitioning
9) Flash the Kernel, as in step 5
10) Flash the recovery package, like in steps 1-4 And that will fix any of your issues
11) After you have recovered your phone, I advise you to have your phone completely up to date by browsing and downloading the firmware for your version through SamMobile!
fruzmatik said:
I wasnt going to use the files from the other thread, I just assumed I could try this procedure once I got the correct files for the SGH-T989D:
Recovering a soft bricked phone
1) Grab the Recovery Package, and you'll see a bunch of .tar files. Take a look at the names. You'll see CODE, MODEM, CSC and .PIT. Put each one in its place.
2) Turn off your phone. Enter Download mode by presing Volume Down + Home + Power button.
3) Plug in your phone. It will show you, in a yellow box in ODIN, ID:COMx (x being the number displayed, sometimes displays 7, sometimes displays 9)
Now here, take a breath
First try flashing WITHOUT the .PIT and re-partition. And only if it DOESN'T WORK OR FIX then you flash with the .PIT and Re-Partition ticked.
4) Once ready and done all your prayers, press Start. Wait patiently. It usually takes 5 minutes to flash.
Have you done everything correctly until now? Then...
Congratulations on recovering your phone!
You deserve some cake afterwards, and some rest
Now, if your problem is the NAND rw coruption, and wasn't fixed by the above fix, then follow these steps :
5) Download the Kernel. Flash it in PDA. Without ticking Re-Partitioning
6) Successful? Nice, hope is still present.
7) Flash the recovery package, following steps 1-4 This should fix your issue. If it does not, then :
WARNING : FLASHING A BOOTLOADER IS DANGEROUS. FLASH WITH EXTREME CAUTION.
8) Download the Bootloader. Flash it as PDA or Bootloader in ODIN. Without ticking Re-Partitioning
9) Flash the Kernel, as in step 5
10) Flash the recovery package, like in steps 1-4 And that will fix any of your issues
11) After you have recovered your phone, I advise you to have your phone completely up to date by browsing and downloading the firmware for your version through SamMobile!
Click to expand...
Click to collapse
Make sure u have the stock USB cord, and remove kies totally from ur PC, even if u think its not running it still may interfere with Odin, do not, do not touch anything on Odin besides PDA, and as long as u download the recovery tar file from the link I gave u, have the factory cable, and are in Odin it will work, try diff com ports on ur PC, mine likes com5 urs may be different, I had the exact same issue and freaked out like I assume u did and this was how I fixed it, u do not have a soft brick, u have a firmware malfunction, the guide for soft brick won't help u, try twrp 2.4, that's the one that fixed mine, if u need help pm me or hangouts an I'll walk u through it step by step...
Sent from my SGH-T989 using xda premium
soupysoup said:
Make sure u have the stock USB cord, and remove kies totally from ur PC, even if u think its not running it still may interfere with Odin, do not, do not touch anything on Odin besides PDA, and as long as u download the recovery tar file from the link I gave u, have the factory cable, and are in Odin it will work, try diff com ports on ur PC, mine likes com5 urs may be different, I had the exact same issue and freaked out like I assume u did and this was how I fixed it, u do not have a soft brick, u have a firmware malfunction, the guide for soft brick won't help u, try twrp 2.4, that's the one that fixed mine, if u need help pm me or hangouts an I'll walk u through it step by step...
Sent from my SGH-T989 using xda premium
Click to expand...
Click to collapse
Thanks! Switched to a different computer and had no issues flashing.
fruzmatik said:
Thanks! Switched to a different computer and had no issues flashing.
Click to expand...
Click to collapse
Glad I could help, sometimes even if u think kies isn't affecting odin it just might be, happy I could be of assist, hit that thanks button if u like lol
Sent from my SGH-T989 using xda premium

[Q] Sprint Note 2 (SPH-L900) Bricked after attempted 4.3 Update

I've been having issue with my Sprint Note 2 for a while. I've also posted this to Reddit and other parts of the forum but so far have gotten no way to fix my issue. Here's the link to Reddit: http://www.reddit.com/r/techsupport...nt_note_2_sphl900_bricked_after_attempted_43/
Sorry, I didn't want to type that all up again and having to deal with formatting and such.
Basically, the gist of it, from what I can gather is that I have accidentally loaded the 4.3 bootloader with KNOX and it is currently preventing me from doing anything productive (flashing CWMR, rooting, installing stock, etc). I read here on the forum that there were ways to do so, especially this post: http://forum.xda-developers.com/showthread.php?p=46861777
I was wondering if there were steps for the Sprint Note 2 SPH-L900?
Any help in debricking my phone is appreciated.
Try these steps.
1. Boot phone into Odin/download mode
2. Flash twrp or cwmr via Odin.
3. When it reboots pull battery and then boot into recovery.
4. Flash this http://forum.xda-developers.com/showthread.php?p=36388145 it is mc2 bootloader, firmware, radio, etc...
5. Reboot phone. Things get weird for a few mins but it will boot.
You are now Knox free once again but you are also bone stock.
Sent from my SPH-L900 using XDA Premium 4 mobile app
jlmancuso said:
Try these steps.
1. Boot phone into Odin/download mode
2. Flash twrp or cwmr via Odin.
3. When it reboots pull battery and then boot into recovery.
4. Flash this http://forum.xda-developers.com/showthread.php?p=36388145 it is mc2 bootloader, firmware, radio, etc...
5. Reboot phone. Things get weird for a few mins but it will boot.
You are now Knox free once again but you are also bone stock.
Sent from my SPH-L900 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I've tried that multiple times. The problem here is that I can't load CWMR or TWRP. At first, I assume that I'd have to root so I downloaded the CF auto root file and flash it using ODIN. Then I tried installing CWMR (after converting to .tar using Caboomi's tool here on the forum). It would reboot and I tried holding down volume up + power + home button but nothing would happen. I try combinations of that and still nothing. I flashed the 4.3 sboot.bin to get it back to stock Samsung bootloader then retried with CWMR without rooting first this time and it still doesn't work. ODIN would tell me that it succeeds but I can't enter Recovery no mater the combination of keys that I press. I'm assuming this has to do with Knox in which case I'd just have to wait for the official 4.3 firmware on SamMobile to flash it since stock 4.1.2 won't work.
QuantumInteger said:
I've tried that multiple times. The problem here is that I can't load CWMR or TWRP. At first, I assume that I'd have to root so I downloaded the CF auto root file and flash it using ODIN. Then I tried installing CWMR (after converting to .tar using Caboomi's tool here on the forum). It would reboot and I tried holding down volume up + power + home button but nothing would happen. I try combinations of that and still nothing. I flashed the 4.3 sboot.bin to get it back to stock Samsung bootloader then retried with CWMR without rooting first this time and it still doesn't work. ODIN would tell me that it succeeds but I can't enter Recovery no mater the combination of keys that I press. I'm assuming this has to do with Knox in which case I'd just have to wait for the official 4.3 firmware on SamMobile to flash it since stock 4.1.2 won't work.
Click to expand...
Click to collapse
After flashing cwm do battery pull...Don't let it auto-reboot.
Also try different version of Odin maybe
louforgiveno said:
After flashing cwm do battery pull...Don't let it auto-reboot.
Also try different version of Odin maybe
Click to expand...
Click to collapse
I tried 3.07, 3.09, and even barebone 1.85 that came with CF auto root. It doesn't work. I can't load recovery just fine (according to ODIN) but I can't get into Recovery.
Here is the fix https://www.dropbox.com/s/s2clvyo4y6gar6s/4.3_Unbrick.tar
I promise this will fix your issue, but when you get done, you will be on MC2 with the 4.3 bootloader, but, it will boot, let you flash recovery and everything. I know this because I did the same thing as you and flashed the old cf-auto root and bricked my phone to, and I created this file to fix it and if you look in the help section, you will find my thread on how to unbrick after 4.3 update fail.
I promise though, this will fix your fone
Keithgordon said:
Here is the fix https://www.dropbox.com/s/s2clvyo4y6gar6s/4.3_Unbrick.tar
I promise this will fix your issue, but when you get done, you will be on MC2 with the 4.3 bootloader, but, it will boot, let you flash recovery and everything. I know this because I did the same thing as you and flashed the old cf-auto root and bricked my phone to, and I created this file to fix it and if you look in the help section, you will find my thread on how to unbrick after 4.3 update fail.
I promise though, this will fix your fone
Click to expand...
Click to collapse
...My God..... What ever you did, it worked. Turns out, Caboomi's file didn't work too well. I couldn't get CWMR working at all even after converting to .tar. I used TWRP instead and it works. Problem was that it asked me for my password, which I don't know since I tried everything, so I had to resort to wiping everything. I installed the file jlmancuso suggested, loading it onto SD card then flashing using TWRP, and now my Samsung Note 2 is debricked.
Your file was a godsend. Thank you!
No recovery stuck on bootloop
im having the same issue could you post that dropbox link again
So i was able to get recovery back but it wont let me mount my sd card so i cant flash anything through recover was hoping the file you have could be loaded through odin as it is a .tar file correct please help and thanks in advance.
Keithgordon said:
Here is the fix https://www.dropbox.com/s/s2clvyo4y6gar6s/4.3_Unbrick.tar
I promise this will fix your issue, but when you get done, you will be on MC2 with the 4.3 bootloader, but, it will boot, let you flash recovery and everything. I know this because I did the same thing as you and flashed the old cf-auto root and bricked my phone to, and I created this file to fix it and if you look in the help section, you will find my thread on how to unbrick after 4.3 update fail.
I promise though, this will fix your fone
Click to expand...
Click to collapse
rckingws6 said:
So i was able to get recovery back but it wont let me mount my sd card so i cant flash anything through recover was hoping the file you have could be loaded through odin as it is a .tar file correct please help and thanks in advance.
Click to expand...
Click to collapse
Yes, flash that file in Odin, it will downgrade you to MC2 with the MK4bootloader
Keithgordon said:
Yes, flash that file in Odin, it will downgrade you to MC2 with the MJA bootloader
Click to expand...
Click to collapse
MJA ? Isn't that an s4 bootloader?
louforgiveno said:
MJA ? Isn't that an s4 bootloader?
Click to expand...
Click to collapse
yep, sorry, I just woke up....I meant whatever version we are on with the note, what is it? MK4? I have both so I keep switching back and forth in the threads. Funny thing is, they are completely different, i will change that, thanks for pointing that out
my friend 's L900 bricked too ,but I cant download the file you provide , the error message is “Error (509) This account's public links are generating too much traffic and have been temporarily disabled”
may you provide another URL to download it or mail it to me ? my email is [email protected] , thanks.
another question , how can i flash it into device with ODIN ? from Pit ? bootloader ?PDA ?PHONE ? or others ?
Sent from my SPH-L900 using xda app-developers app
---------- Post added at 06:23 PM ---------- Previous post was at 06:14 PM ----------
Keithgordon said:
yep, sorry, I just woke up....I meant whatever version we are on with the note, what is it? MK4? I have both so I keep switching back and forth in the threads. Funny thing is, they are completely different, i will change that, thanks for pointing that out
Click to expand...
Click to collapse
my friend 's L900 bricked too ,but I cant download the file you provide , the error message is “Error (509) This account's public links are generating too much traffic and have been temporarily disabled”
may you provide another URL to download it or mail it to me ? my email is [email protected] , thanks.
another question , how can i flash it into device with ODIN ? from Pit ? bootloader ?PDA ?PHONE ? or others ?
Sent from my SPH-L900 using xda app-developers app
yea I still cant dowload it sorry for being a pest.
Keithgordon said:
Yes, flash that file in Odin, it will downgrade you to MC2 with the MK4bootloader
Click to expand...
Click to collapse
hello if you are online i need some help i dl the 4.3 note 2 update it has a different build than the one sprint has there are some features that are not on this build is there any way for me to get the ota from sprint
rckingws6 said:
yea I still cant dowload it sorry for being a pest.
Click to expand...
Click to collapse
rckingws6 said:
So i was able to get recovery back but it wont let me mount my sd card so i cant flash anything through recover was hoping the file you have could be loaded through odin as it is a .tar file correct please help and thanks in advance.
Click to expand...
Click to collapse
Try using TWRP instead. It gives you the option to mount an external SD card. Also try restarting into recovery again. I had Recovery bugged out on me once.
QuantumInteger said:
Try using TWRP instead. It gives you the option to mount an external SD card. Also try restarting into recovery again. I had Recovery bugged out on me once.
Click to expand...
Click to collapse
i need some help
yea i can get into twrp recovery now but my sdcard wont mount thats why im trying to use odin
QuantumInteger said:
Try using TWRP instead. It gives you the option to mount an external SD card. Also try restarting into recovery again. I had Recovery bugged out on me once.
Click to expand...
Click to collapse
For those of you who have bricked Note 2s (SPH-L900), I'm going to drop a DropBox link here to a folder of ALL of the files that I used to unbrick my phone. I experimented with multiple methods (and several sleepless nights). Some of them will be useful to you, not all. I have the Android SDK and Caboomi's converter for .img to .tar. It doesn't work too well for CWMR just FYI. ODIN-OC will attempt to load stock MC2 onto your phone but it won't work if it's bricked. Arc Converter is a program I used to try convert the MK4 .zip file to .tar to try and flash an update using ODIN. It didn't work. The steps that I took to unbrick my phone will be posted after the link.
https://www.dropbox.com/sh/c2bfpfdf0qbs6bu/ZiNC-BF5kf
Be patient. Some of the files are still updating.
Steps:
1) Put your phone into Download mode by holding volume down + power + home button at bootup
2) Use ODIN (3.07 or 3.09) to load the 4.3_Unbrick.tar file. This will take a bit of time so be patient. Once the phone boots up again, you'll get past the boot screen that says "Samsung Galaxy Note II" and you'll get the Samsung logo with the spinning icon but it will loop. This is normal.
3) Next, power off (yank the battery and cable, leave battery out but plug the cable back in) and reboot into download.
4) Flash the TWRP .tar file (don't try converting the CWMR to .tar, it won't work) then reboot.
5) Hold volume up + power + home button (be patient here)
6) You should see the Team Win logo. You're now in recovery. The TWRP may ask you for the password. It is NOT the passcode to your lockscreen or your Google password. I have no idea what it is. At this point, you'd have to wipe your phone (internal only) if you want to flash the stock recovery.
7) Load the MC2 stock recovery file with counter reset onto a microSD card and mount it onto the phone (play around with TWRP, if it doesn't see the SD card the first time, restart or play with the mount function). Just be careful not to wipe your microSD card.
8) Flash the stock recovery (give it time) and it'll restart. You should be back at 4.1.2.
EXTRA STEPS
If you're still interested in 4.3, load the MK4 update onto the microSD card as well. BEFORE you go through the activation process for the 4.1.2 firmware at boot, boot into recovery. Flash the 4.3 update using stock recovery. This should put you onto 4.3 after the phone reboots. You should now have stock 4.3 (no root).
Sorry for all the download errors, I am uploading to my websight right now and as soon as it uploads, I will post the URL, it should download much faster too. I didnt realize so many people needed it

[Q] Unbricking trouble

I have the galaxy m919, and had a bad flash yesterday. My phone is now softbricked, and I am unsuccessful in fixing it.
I have run ODIN with a PDA file and it did not fix the problem. I am pretty sure I also need a PIT file to load. I thought I had one saved from when I originally got my phone and decided to root it and put the Infamous rom on it, but can't find it for the hell of me.
All attempts to search for the files online just gives me .tar files.
Any suggestions?
If I was soft bricked I would flash the stock img. When you say bad flash I assume the process was interrupted. Go here http://forum.xda-developers.com/showthread.php?t=2336392 and download the stock ROM open Odin and select PDA and find the stock MDL tar file and select it, then put your phone in download mode by pushing (volume down+home and power) then plug it in you your PC. Make sure the com window lights up and click start. Let the phone reboot and then re-root or do what you wish. I hope this helps. Good luck
Sent from my SGH-M919 using xda app-developers app
Thank you! I wiped it in recovery, and it fires up just fine now on the stock rom I installed.

Categories

Resources